Search Documents

By D. Arku

The increased use of sensors to facilitate automation has led to an explosion of data. As data sets grow in size, their use becomes more complex. Therefore, there is an incentive for reducing the size of the datasets, as long as this does not compromise information gleaning. With this in mind, this project explored basic aggregation as a viable alternative to amassing large amounts of data. The goal of the project was to determine if one would arrive at different conclusions had they analyzed aggregated data instead of raw data. In a mine, operational data is typically used for tracking process statistics, correlation between factors, autocorrelation and multivariate models (for a factor of choice). Therefore, this project compared results from such analyses when it was conducted with aggregated data (AD) with the results of analyses conducted with raw data (RD). The data consisted of one-minute-apart readings from a semiautogenous grinding (SAG) mill on the horsepower, feed rate (tons per hour), rotations per minute (rpm), noise, recycle (tons per hour), density (% solids) and bearing pressure (psig). This data was aggregated by averaging five and 10 continuous (one-minute) observations. Changes in statistical measures between the two approaches were typically within 5% of each other. Differences in correlation coefficients between RD and AD(s) were also within this range. Autocorrelations present within RD were preserved in AD, as long as the time lags were scaled for the amount of aggregation. Regression and neural network models were also developed for power consumption. The prediction performance of developed models was similar whether one used raw data or aggregated data. Overall, it appeared that aggregating the data based on 5- or 10-minute time spans would not have resulted in conclusions (from simple or complex analyses) being different from using raw data. In other words, whether one had used raw data or aggregated data, the conclusions would have been the same, suggesting that time domain aggregation, a common industry practice, is a good alternative to storing high-density data in this case.

By Robinson Leon-Diaz, Alberto Jaen-Toribio, Raymond Blanchard, Mike Deevy, Miguel Fuentes-Llanos

"Tunnels designed to NFPA 502 are required to withstand the RWS time-temperature curve, more specifically prevent progressive spalling and loss of strength of steel reinforcement. Fire boards or spray-on layers can be effective, however, these solutions have capital and whole-life cost implications. The use of “fire resistant” concrete based on a suitable aggregate with polypropylene fibers has also increased in recent years. This article presents a new methodology for thermal and structural analysis of segmentally lined tunnels, which permits the analysis of project specific fire curves and an assessment of different fire protection strategies. The effectiveness of fire boards is assessed along with whether “fire resistant” concrete alone is a viable means of achieving the required protection. Finally, since NFPA 502 recommends water-based fixed fire-fighting systems for Category C and D tunnels, we discuss the question of how a fixed fire-fighting system should be addressed within the structural design. INTRODUCTION Protecting road tunnels from structural damage and collapse is a key requirement for both life safety and business continuity. Where road tunnels are part of key highway corridors, protecting business continuity is a high priority for owners, operators and the Authority Having Jurisdiction. For existing tunnels, compliance with NFPA 502 may require upgrades with either passive fire protection and/or water-based fixed firefighting systems. For new tunnels, compliance with NFPA 502 requires a combination of good practice in design and fire testing. A water-based fixed firefighting system is a Conditionally Mandatory Requirement1 for Class C and D tunnels, i.e. all tunnels greater than 300m and 1000m long respectively. The basis for fire safety design of new tunnels and assessment of existing tunnels is the worst-case fire scenario. A number of factors, including but not limited to the following, influence this design fire scenario:"

Jan 1, 2016

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By Anita Wu

"GENERAL BACKGROUND/CONTEXT The £300 million Bond Street Station Upgrade project will provide essential congestion relief and step-free access to an important interchange and destination station in the heart of the London Underground network. In 2010 London Underground (LU) let a design & build contract to Costain Laing O’Rourke (CoLOR), with the works to be completed in early 2017. CoLOR’s lead designer is Halcrow-Atkins JV (HAT). The station upgrade works comprise the following principal elements: •,A new satellite ticket hall on the North side of Oxford Street •,Two additional escalators and stairs providing congestion relief to the Jubilee line platforms •,Four lift shafts to provide step-free access between the different levels of the station •,Additional stairs to Central line platform level •,Tunnelled connection to the Crossrail station immediately to the south •,Connecting passageways, including ten connections to existing station tunnels. To achieve this, an existing property at 354-358 Oxford Street has been purchased and demolished, and the basement deepened to make provision for the new ticket hall. From this basement two circular shafts have been sunk, providing construction access for the tunnelled passages and lift and escalator shafts. The tunneling is principally in the London Clay stratum, which is widely recognized as a favorable tunneling medium, although the deepest parts of the works extend into the Lambeth Group strata which consist principally of stiff clays at this level but also contain water-bearing sands. The majority of tunneling has been carried out using mechanical excavation and sprayed concrete linings but other techniques have been used in areas where SCL is not practicable.A key challenge for design and construction of the works has been spatial constraint, in particular due to: •,The existing underground station layout •,The Limits of Deviation for the works •,The small construction site at 354-358 Oxford Street •,Overlaying Third Party assets including Listed buildings, sewers and water mains."

Jan 1, 2016

By Earle Bagley

In late 1971, the Sun Company, then known as Sun Oil Company, acquired a large surface mineable federal coal lease with the thought that those coal measures within its boundaries would provide a future feedstock of either coal or coal liquification. Our Cordero lease was one of the last Federal coal leases let before the recent decade long leasing moratorium. Because of the tremendous demand for compliance steam coal for the electric power industry, a decision was made to develop the property to serve that market. In 1974, Sunoco Energy Development Company (SUNEDCO), the non- oil and gas energy unit of the Sun Company, began engineering studies for development of the lease. The mine was originally designed at a 12.0 million ton per year capacity. The Cordero Mining Company was formed to mine and operate the property. Construction of the facilities adjacent to the lease began in January 1975. Due to the Sierra Club versus Department of Interior Secretary L. B. Morton suit, work within the lease was delayed until mid-1976 when pre-stripping of the overburden began.

Jan 1, 1982

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By Howard N. Egan

The importance of coal as the major energy source has led to wider interest in the recovery of waste coal fines as a usable product. An additional incentive for fine coal recovery has been the increased emphasis on environ- mental pollution control and conservation of the nation's natural resources, Accordingly, a series of studies and tests were performed to investigate the feasibility of the recovery, concentration, balling and pelletizing of coal fines as a marketable adjunct to existing mining and beneficiation operations. These studies were conducted at the existing operations of the Eastern Coal Corporation at Stone, Kentucky, and the Metallurgical Laboratory of Arthur G. McKee & Company in Cleveland, Ohio. The purpose of the investigations was to recover the fines from the effluent waste waters of an existing preparation plant and transform them into a high carbon, low sulfur and ash product capable of being handled with a minimum of degradation and dusting problems. The fines were relatively high in ash content prior to processing, and flotation pretreatment served a combined function of beneficiation, recovery and water clarification, The minus 28 mesh coal concentrate containing 40 to 45 percent minus 325 mesh size material had an ash content varying between 5 and 7 percent and a sulfur content of less than 0.5 percent. Chemical and size analyses of the effluent and concentrated fines are presented in Table I for comparison.

Jan 1, 1967

By Thomas J. Neil, O&apos

Mine land reclamation is a comparatively new science-Although some mining companies point with pride to reclamation efforts of 20 to 30 years ago these were the exception rather than the rule. In the last ten years the skyrocket of environmental awareness has been awesome to behold. Future shock gripped mine operators everywhere as they struggled to cope with rapidly changing and escalating demands. The initial result was that two divergent points of view became dominant. Environmentalists said, "Put it back the way it was," and the miners responded, "Let's grow some weeds and hide it." These views are not surprising as they represent rather obvious alternative responses, albeit at opposite ends of the decision spectrum. The former case has prevailed more often than the latter, as most state and federal legislation -- both proposed and passed -- has required drastic alteration of the post-mining landscape so that evidence of prior mining is largely obliterated. An exception to this has been in porphyry copper country where the infrequent abandonment of mines has given emphasis to the second philosophy -establishing vegetative cover on mine waste materials. Now, it should come as no revelation to most mining people that both of these approaches to mine reclamation suffer from serious drawbacks when applied to open pit copper mines. First, whereas waste dumps and tailings dams can be vegetated with some aesthetic benefit, the massive presence of copper mining operations remains very prominent. It is difficult to conceal an open pit copper mine. Second, returning open pit copper mines lands to their original topography and productivity is simply not a reasonable alternative.

Jan 1, 1976

In early June, Rio Tinto?s chief executive officer Tom Albanese said that he expected demand for iron ore, aluminum and copper to double in the next 15 years. Driven by global industrialization and urbanization, Albanese said during his company?s annual general meeting that to meet the demand in 2030, the additional supply required will be equivalent to replicating the iron ore output of Australia?s Pilbara region every five years, adding another aluminum production complex the size of Canada?s Saguenay every nine months and developing another copper mine the size of Escondida, in Chile, each year.

Jan 1, 2010

By C. Clark, J. Johnson, M. Stepan

"Shotcrete and mesh are often installed to control ground deformation, falls and ejection between bolts. The combination of mesh and shotcrete forms a panel or plate that is typically bent by ground extruding between restraining rockbolts. The ground pressure applied (that is, the resistance of these panels to bending) over large ground deformations is important for maintaining ground support safety. This paper describes a new test device that measures this resistance and its evolution over large deformations. Mixes of shotcrete, mesh and other components that can maintain significant support pressure are desired, a characteristic described as the “toughness” of support. Results show toughness depends largely on how shotcrete is integrated with other components. Shotcrete strength is less important. INTRODUCTION Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often called upon to do this (Figure 1). Applications are especially common in mines with squeezing ground or seismic loading. The support pressure maintained during ground deformation is key to the performance of these systems, and to protecting miner safety. However, the toughness of a design is difficult to estimate. Researchers at the Office of Mine Safety and Health Research (OMSHR) responded to this deficiency or “gap” by designing a full scale test device, described in this paper, and beginning a testing program. Some initial results from this program are reported to demonstrate test capabilities.BACKGROUND - TOUGHNESS Mining in ground that fails from the combination of in situ and mining induced stress is commonplace. Ground support elements are installed to reinforce such ground and preserve mine safety. Typically, the strength of support is considered key, and is used to prevent or halt yielding. However, ground movements driven by creep of weak ground or seismic loading may be impossible to halt altogether. In these cases, it is essential that support is able to yield with the ground in a safe manner while maintaining confining pressure that mobilizes the strength of rock in the immediate perimeter of the opening. In addition, it’s usually desirable to contain ground between rockbolts to protect miners from loose rock that might fall or be ejected. Shotcrete and screen are often employed, sometimes together and in combination with other support elements, to accomplish this function. A key characteristic of such a system is its ability to maintain support pressure through large ground deformations, a characteristic often called “toughness” – especially in support systems incorporating shotcrete. Toughness can be quantified as the work done during deformation (e.g. force x displacement)."

Jan 1, 2015

By McCarthy. Richard E.

The prime movers of the Centralia Project, the surface coal mine and the power plant, private utilities are very aware of public attitudes. They have established and maintain the reputation for leadership in public service and are genuinely concerned that this project initiate the pro-grams and design the hardware to answer the question :What will be the impact of the mine and the plant on the physical environment, i.e., the air, soil and the water." So in the beginning almost as soon as the decision had been made to go ahead with the project, officials of the two private utilities, Washington Water Power and Pacific Power & Light went on record and publicly stated time and again that the overall approach of the Operators would be to do all that was reasonably possible to safeguard the environment. This attitude became part of the thinking of the project planners, part of the design of the power plant and part of the plan for the surface mine. The coal to be mined is from the Skookumchuck formation. The formation is Late Eocene and is made up of poorly consolidated marine and non-marine deposits. The major overburden removal equipment is a bucket-wheel excavator -conveyor system and a 56 yard dragline. Mining of the coal will be done with truck and shovel. The coal is processed, washed and crushed to 1 ¼ " for delivery to the power plant. The muddy water created by the washing process is chemically treated and the solids removed by a thickener-vacuum filter system.

Jan 1, 1971

By F. G. Loper

Simulation as a mathematical technique is not new. However, recent increases in digital computer speeds and the ease of programming with languages such as Fortran have centered a good deal of attention around simulation in the last few years, Many sophistications of the method have been developed during this time. However, the ability to simulate mathematically still hinges on the ability to ignore unimportant details which would complicate the mathematics and make simulation impractical, Thus, with this attitude in mind, it becomes very easy to design a pseudo- simulator which will predict average conditions very well, but can not truly allow a detailed study of the system being simulated. Most simulations fall into this category, along with the case mentioned here. This paper is not intended to be a critical treatise of the simulator used to study a particular mining system. Instead, it will be used to illustrate the aspects of simulator development. The steps in the development of any simulator are described, along with same detail of the phosphate mine simulator itself.

Jan 1, 1966

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By James B. Fletcher

The Miami mine is located near the town of Miami, Gila County, Arizona. The Miami mine started mining in 1910 and finished in July, 1959. The orebody was divided and mined as follows: Tons High Grade 24,400,000 - Top slicing, sub-level caving, etc. Low Grade 105,100,000 - Block caving Mixed ore 9,800,000 - " Low Grade #2 13,100,000 - " Total Mining 152,400,000 GEOLOGY Ore minerals are largely in pre-Cambrian Pinal schist intruded by tertiary Schultz granite porphyry and covered to some extent by Quarternary Gila conglomerate. The structures are highly faulted and shattered. The Miami fault on the east cuts off the ore and the Pinto fault on the southwest caused re-oxidation of enriched sulphides producing mixed ore. MINERALOGY The chief mineral is chalcocite, with chalcopyrite, bornite, covellite, malachite, azurite, chrysocola, cuprite, native copper, and molybdenite as minor minerals. The ore minerals occur in seams, veinlets and disseminated particles. In block caving there is always some dilution, and drawing of ore stops when the grade drops past an economical point. This results in a small amount of copper left in the stopes below the capping. There is some copper in the capping, probably below 0.03% or less than 0.6 lbs. per ton. Over the low grade #2 orebody and portions of the high grade there was an oxide capping which was not mined. The crushed pilars are another source of copper. The leaching at Miami is an attempt to recover this last remaining copper of a worked-out mine. The enrichment at the Miami mine had gone more nearly to completion than most ore bodies in the southwest. There is practically no pyrite in the capping and very little in the ore.

Jan 1, 1971

By Theodore M. Olson

The Washington State Highway Department consists of seven geographic dis¬tricts. District offices are located in Seattle, Wenatchee, Olympia, Vancouver, Yakima, Spokane and Bellevue. District is covered from the Spokane office, and is responsible for the six counties in the northeast corner of the state (Fig.l). It is bordered on the north by the International Boundary, on the south by the Snake River, on the east by the Washington - Idaho border, and on the west by a north-south line thru Lake Roosevelt. The landslides to be discussed in this paper are at Colfax, Washington, which is located in the southeast corner of the district. The town of Colfax is situated in a narrow valley eroded into the Tertiary volcanic basalts by the Delouse River. The valley walls are steep and generally colluvium mantled. State Highway 1°c, from Spokane to Colfax, descends into the valley from just north of Colfax on a bench cut into the valley wall. The highway department designed a widening project to increase the misting two lane roadway to three lanes, thus providing a passing lane for uphill traffic. The third lane was constructed as a cut section for the entire length. Construction excavation was begun at the top of the hill in silts of eolian origin. Proceeding downhill, excavation encountered three individual basalt flows with two zones of palagonite tuff separating them. The upper palagonite zone was dry, and excavation proceeded across this zone with no mishaps. The lower palagonite zone carried considerable groundwater. As excavation crossed the lower zone landsliding became contemporaneous with excavation, due to removal of toe of slope and saturated conditions. Remedial measures for landsliding consisted of designing shot rock buttresses across the palagonite zone and also the installation of horizontal drains to reduce hydrostatic pressure.

Jan 1, 1971

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner?s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutterhead, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head?s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner generally improved air quality at both sampling locations to varying degrees in some, but not all, mines when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By Gary L. Mowrey

Visible and sometimes audible indications of excessive underground rock pressure such as pillar fracturing, squeezes on chocks, and "roof talk" are familiar to mining engineers. Such signs often precede rock failure on a larger scale and therefore may be used as a warning. Nevertheless, these subjective observations do not provide an adequate means of evaluating the existing rock pressure conditions in a mine. One method which appears to be extremely promising in determining the stability of geologic structures in general is that of monitoring their associated micro seismic activity. Mining engineers generally agree that during the process of rock deformation and failure small-scale seismic ("microseismic") vibrations are produced in the rock itself. These transient vibrations propagate through the rock structure and may be detected at a considerable distance from the failed rock by employing suitable electronic monitoring equipment. Hardy (1) has presented a detailed review of microseismic research in the mining, petroleum, and geoscience areas, and it is apparent that relatively little application of micro seismic techniques have been made in coal mines. This is especially true in North America since here most coal mines are fairly shallow and consequently are not generally subjected to excessive stresses. Furthermore, strict Federal and State mining laws limit the use of electrical equipment in coal mines complicating the use of the necessary monitoring facilities. In terms of both mine safety and economics, monitoring microseismic activity appears to be invaluable in the detection and location of over-stressed pillars and unstable roof conditions caused by development and production work. In 1970 The Pennsylvania State University Rock Mechanics Laboratory became involved in a research project, sponsored by the U.S. Bureau of Mines, to investigate the feasibility of using microseismic techniques to detect and to locate potential regions of instability around a longwall coal-mine operation [Hardy and t10wrey (2); Mowrey (3)]. In this study geophones (velocity gages) located in an array of shallow boreholes drilled from the surface above the active area of the longwall were employed to detect microseismic activity, and a mobile micro-seismic monitoring facility was used to condition and record this data for later analysis. This project is unique in that measurements were made from near-surface geophones rather than geophones installed on the mine itself. Two advantages are apparent, namely that (1) there are no electrical limitations on the monitoring system and that (2) mining operations can continue normally because there is no monitoring equipment or cables in the mine.

Jan 1, 1978

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

By S. Mafi

The Broken Aro project is associated with a 1910 abandoned underground mine complex that has been discharging aeid mine drainage from entries, seeps and springs. The Ohio Department of Natural Resources(ODNR), R&F Coal Company (R&F) and American Electric Power (AEP) are involved with this unique project that will remine the abandoned underground complex and install a mine seal constructed of fixated flue gas desulfurization (FGD) material. The goal of the project is to eliminate or reduce the acid mine drainage that is discharging into the watershed. This paper discusses remining, installation of the FGD mine seal, government financed reclamation projects and future application to active and abandoned mining sites.

Jan 1, 1998

By G. R. Erdman

The industrial mineral filler plant of the Gouverneur Tale Company is equipped with a good dust collection system installed long before the recent popularization of environmental pollution. Credit for this fact is due to the foresight of Mr. R. S. McClellan, Project Manager and subsequent Vice President and General Manager of Gouverneur Talc, who recently retired as Vice President Engineering of the parent organization, the R. T. Vanderbilt Company. Also instrumental in the early stages of plant operation and the solution of start-up problems was J. A. Gustin who is now an engineering consultant located in Martinsville, Va. Credit is most certainly due to the late R. T. Vanderbilt, the company's founder, who favored and approved the investment in the necessary facilities that were far ahead of all competitors in the industry at that time.

Jan 1, 1972