Search Documents

By Perry L. Christian

"Mana/ta Coal Ltd. 's Costello Mine, located seven kilometres east of Estevan, Saskatchewan, has been operating at the present location since 1960. During the past twenty-three years, annual production of lignite coal has averaged 590 000 tonnes. The coal is used for power generation and for industrial and domestic use. Markets, operating techniques, facilities in place and reclamation are discussed. Introduction The Costello Mine (formerly the Klimax Mine) is located in southeastern Saskatchewan, approximately 210 kilometres southeast of Regina and 5 kilometres from the United States' border, as shown in Figure 1. The present mine, 7 kilometres east of the city of Estevan, has been operating since 1960. The history, however, of the Costello Mine and of the Estevan Coalfield dates from the initial settling of the area in the 1880s. Mining initially consisted of burrowing into the side of the Souris River Valley or other hillsides where the coal seam was exposed. Eventually, slopes were put down in the Estevan/Bienfait area and vigorous underground activity existed. In the late 1920s surface strip mining was introduced. The use of strip mining progressed to the point where it completely replaced underground mining in the 1950s and it is the only method in use today. During the past 23 years annual production has averaged 590 000 tonnes. The lowest production was in 1960 when the mine was starting up at 167 000 tonnes and the highest production was in 1977 when production was 1 509 000 tonnes. The Costello Mine controls approximately 11 400 hectares of mineral rights in the Estevan area. This is made up of 4 900 hectares of freehold coal and 6 500 hectares of leases. The area forms a large, irregular shaped configuration. Most holdings are contiguous and adjacent. The mine also owns some 8 400 hectares of surface rights. The lands under the Costello Mine's surface rights control, which are not being used in the mining operation, are leased to local farmers and ranchers. This ensures that the land is used to its full potential, both before and after mining."

Jan 1, 1985

By M McCarthy

Over the last six years Mandalay Resources has increased production rates and improved safety outcomes at its Costerfield mine in Victoria, Australia. This mine is an underground operation utilising narrow mining techniques to extract vertical veins, and produces up to 80 000 equivalent ounces of gold per annum, in both gold and antimony value.The operational challenges of narrow vein mining include controlling overbreak when veins being mined are only 300 mm wide. The mine has developed methods and modified equipment to suit extraction of these veins. Productivity improvements over the period have involved development of a stoping method and equipment to suit 1.8 m wide development drives. Over the last five years and during a skills shortage, recruitment, training and retention of personnel has been key to keeping corporate knowledge and skills to execute a careful efficient mining technique to minimise overbreak.Managing an underground operation close to nearby residents has unique challenges. Historically Victorian residents had family members work as underground miners; however, in the current day with few underground operations in this jurisdiction, community knowledge of mining has decreased. The Costerfield Operations are only 100 m from the nearest residence and the company values community engagement, partnership and investment with local Heathcote organisations.The mine has invested substantially in executive coaching of its leadership team early, which has paid dividends in problem solving potential of that team and ensuring the operation delivers on its promises to all stakeholders. The operation has become safer and employees are now more aware of their individual contribution in producing safe, efficient gold and antimony that benefit the whole operation, community and the region.CITATION:McCarthy, M, 2016. Costerfield – a narrow vein case study, in Proceedings International Mine Management Conference, pp 331-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Vincente M. Jr. Lim, Brain W. Lawrence

Underground mining operating costs consist pri¬marily of direct costs such as labor, supervision, ma¬terials, and supplies, plus indirect costs. The material and supply costs vary substantially between mines but commonly range from 35 to 60% of the total direct costs. As part of the preparation of accurate operating cost estimates for a project, information must be as¬sembled to select the material and supply items and to determine the quantities of these items that will be required. Cost data then can be incorporated with the estimated material and supply requirements to determine the total material and supply costs for the project. Estimated quantities will vary considerably between mining projects depending upon factors such as the type of material being mined, the mining method, the equip¬ment selected, drilling and blasting techniques, mucking and haulage methods, ground support requirements, number of men employed, etc. Valuable information often can be obtained from suppliers and manufacturers, including data on current operating practices for similar projects, recommenda¬tions for the specific project, and preliminary cost quota¬tions. However, quotations obtained for estimates are generally higher than the prices paid at the time of purchase. Mines operating in the area, or those mining under similar conditions, also can provide essential design information, but it often is difficult to obtain cost information from the operators. Estimated costs for the most common major items of underground materials and supplies are presented in the accompanying tables. They represent current costs or cost ranges and are intended to be used only as a guide when preparing budgetary estimates for materials and supplies. Cost data were obtained mainly from suppliers and manufacturers, with up to three quotations being ob¬tained for each item whenever possible. In most cases, as noted in the table footnotes, prices were based on quantities representing normal requirements for me¬dium-size mine operations. Every attempt was made to assure accuracy. However, the cost for most items, especially those with multiple sources, can deviate sig¬nificantly for various reasons such as geographical loca¬tion, current market conditions, quantities ordered, size of the customer (which could influence the ultimate quantities purchased), and the ability of the purchasing department. It is also for these reasons that the actual amount individual mines are now paying for specific items may vary from the estimated cost in the tables. The cost for specific sizes of items that do not appear in the tables often can be factored from the data pre¬sented. Costs for many items can be converted easily to a unit that sometimes is more basic, but not as com¬monly used, such as from a length to a weight unit. Other items not listed, such as repair parts for equip¬ment, will involve contact with suppliers to determine specific recommended requirements and to obtain costs for these items as related to each individual project. Costs are expressed in terms of US dollars as of 1978 unless otherwise specified. All measurements, sizes, and weights are expressed in conventional units (i.e. feet, inches, pounds) ; applicable metric conversion fac¬tors follow each table. Costs are represented for drill steel and bits; mining explosives; blasting caps; blasting supplies; ground sup¬port items; ventilation equipment; utility pipe, utility hose, and accessories; mine track and accessories; tires for underground equipment; lubricants and fuels; and miscellaneous supplies.

Jan 1, 1982

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By S. C. Schmelter

The destabilizing effect of water pressure on rock mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock mass deformation and transient fluid flow is used for this purpose. The traditional soil mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1997

By Yiming Sun, John Stolz, Jakob Walter, Drew Mason

The Courthouse Commons SEM Tunnel was excavated within 6 feet of cover beneath two buildings in downtown San Diego utilizing high-precision geotechnical instrumentation. The excavated dimensions are approximately 25 feet in diameter and 328 feet in length connecting two in-service detentionlevel security buildings. Presupport includes large-diameter grouted canopy pipes and smaller pipe spiles. Initial support consists of fiber-reinforced shotcrete with lattice girders. This paper presents observed ground and structure behavior and lessons learned. During construction an unanticipated brick structure was encountered, and methods were developed to improve adhesion of shotcrete to sandy soil and to reduce rebound

Dec 1, 2022

By R Barritt, P Scott

Across the globe, it is a common scenario that tailings storage facilities (TSFs) are being decommissioned; however, their subsequent impact on the local environment and landscape can often be overlooked during the mine planning process. In addition, the requirement of a cover system for a facilities closure may not be a priority until the latter stages of the mine/mill operation when potential cover materials may have been utilised elsewhere or, worse, buried. Developing a conceptual design and closure plan for a TSF early in a mining venture is fundamental to its success once operations have ceased. If a cover system is a planned component for rehabilitation of a TSF, it is vital that its design is appropriate to the facility and any local site constraints, such as climate and cover system material availability. It is also strongly recommended that various cover system options are physically trialled at the site by using performance-monitoring instrumentation. Through this process, an informed decision can be made regarding the most appropriate cover system design to meet any regulatory and stakeholder closure objectives and criteria specific to the site in question; however, in order for the cover system’s performance to be determined through on-site trials, it is essential that an appropriate instrumentation design is utilised. Often, little attention is paid to the data that is being obtained, and its importance may only become apparent after several years of monitoring at an expense to the venture. This should not be the case. Many sites have used an appropriate initial planning stage to understand what is required for the successful closure of a TSF, how it can be achieved and how monitoring data can be utilised to prove, or otherwise, that a cover system design will be a success.CITATION:Barritt, R and Scott, P, 2015. Cover system performance monitoring for tailings – are we doing it correctly?, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By B. K. Ayres

Modern management of uranium mine or mill waste storage facilities (WSFs) often requires that they be remediated or decommissioned with a cover system. In addition to creating a self-sustaining landscape that supports the end land use, cover systems are intended to reduce long-term risks to human and ecological receptors from the stored waste to acceptable levels. The performance and longevity of a cover system will be strongly influenced by the features or shapes of the WSF final landform. Hence, cover systems and landforms must be thought of as an integrated design. Based on the author’s experience, the most important elements of the design process for maximizing the potential of WSF final landforms / cover systems being sustainable over the long term are noted in this manuscript. Several key items that must be considered and addressed during the planning phase of constructing a WSF final landform are also described. Various methods for monitoring performance of a WSF final landform are also reviewed. Key aspects associated with decommissioning a tailings WSF and waste rock pile at the former Cluff Lake uranium mine in northern Saskatchewan are included to illustrate many of the practical insights provided in this paper.

Jan 1, 2020

By Howard A. Perko, Margaret Dring, Gerald Verbeek, Scott Slaughter

Helical piles have become a widely used deep foundation system in recent years due to their many inherent advantages. The cone penetration test (CPT) is commonly used in geotechnical practice to evaluate subsurface conditions for deep foundation design as the method provides a continuous soil profile in a short amount of time, measures in-situ soil strength, and in many ways behaves similar to a “mini pile” during penetration. In the CPT test, an instrumented cone is hydraulically advanced into the soil at a constant rate. As the cone is advanced, strain gauges embedded in the cone body continuously measure the tip resistance and side friction. In addition, a piezometer element is commonly used to measure the (dynamic) pore water pressure in the soil as the cone is advanced. A study was conducted comparing the CPT tip resistance to helical pile installation torque and capacity. In this paper, the outcome of this study was compared with historical data of helical pile installation torque records, static analysis predictions using commonly used techniques, and pile load test results over a wide range of soil conditions. A literature review was also conducted where a comparison was made for CPT tip resistance and helical pile installation torque data with previously published correlations.

Sep 8, 2021

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By Erik S. Bernard

"INTRODUCTION Conventional steel bar reinforcement is used in many tunnel linings to provide high flexural and tensile load resistance. These Reinforced Concrete (RC) tunnel linings may suffer flexural cracking during service or, in the case of precast concrete segments, during production, handling, or installation. Cracks can lead to corrosion of steel reinforcement, so limits are placed on maximum acceptable crack widths to reduce the likelihood of corrosion during the intended design life (AFTES, 2013; MC2010, 2012). However, the relatively light level of reinforcement used in many applications can result in quite wide in-service crack widths, so either additional steel bar reinforcement is required to limit maximum crack widths, or fibers can be included to control crack widths. Numerous investigations have been undertaken into the efficacy of including steel fibers to reduce crack widths in conventionally reinforced members (Stang and Aarre, 1992; Abrishami and Mitchell, 1997; Bischoff, 2003; Dupont and Vandevalle, 2003; and Jansson et al, 2010), but steel fibers suffer the problem that they are at least as sensitive to corrosion at cracks as steel bars and therefore have similarly tight limits placed on acceptable crack widths (AFTES, 2013). An alternative means of maintaining narrow crack limits in RC members has therefore been sought. The current investigation was instigated following an observation that theories promoted as an explanation for the ability of steel fibers to reduce crack widths in reinforced concrete flexural members (Deluce et al, 2014) do not depend on the material composition of the fibers used but instead depend primarily on the tensile stress generated by the fibers across cracks. Since it is known that macro-synthetic fibers are capable of equaling the post-crack tensile capacity of steel fibers, it has been hypothesized that macro-synthetic fibers are also capable of reducing crack widths in reinforced concrete flexural members but with the added advantage that macro-synthetic fibers are completely immune to the effects of corrosion. Use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete flexural members subject to aggressive environmental exposure is more rational than use of steel fibers because steel fibers are very sensitive to the corrosive effects of environmental exposure at cracks. The current investigation was therefore undertaken to explore the potential use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete members subject to flexure. Barchip BC54 fibers were selected as they are one of the most widely used and competitive high performance macro-synthetic fibers currently available."

Jan 1, 2016

By N Anderson

With traditional grade control processes, geological models are created by geologists at the completion of the data collection stage and wireframe construction is closed off at a set date to allow for time to complete the estimation process. Any issues identified at earlier stages or the addition of new data requires the estimation process to be started again. Alternative interpretations are explored only if time allows and often in a limited fashion. An alternative workflow has been developed at the Waihi Underground Gold Mine utilising Leapfrog Edge and Seequent Central. Geological and grade control models are created, dynamically linked, and saved as separate branches. A project geologist is able to work on the grade control model and a mine geologist on the geological model simultaneously. This allows for a non-linear modelling workflow with continual review and feedback. The introduction of new data can occur right up to the model due date, with data collection, validation, alternate interpretation, and review happening incrementally. Models are categorised and stored in Seequent Central according to project status. An approved version of the geological model and grade control estimate are uploaded at the time of release and transparently capture all data used at a point in time, as well as the review process. Dynamically updating models for grade control has reduced turnaround time while increasing accuracy and quality. Estimates of individual domains are vastly improved from being able to rapidly evaluate the effects of model parameter changes in real time and 3D. Development and stope design directly benefit from these streamlined processes, with higher quality, timely production occurring as a result.

Mar 22, 2022

By P Lukic

The definition of the working sections that will be used in a mine is usually initially made in the field by the geologist supervising the drilling program. These initial definitions are often made on the basis of rules of thumb such as æcoal less than 30 cm thick cannot be mined separatelyÆ; æpartings more than 30 cm thick will be mined separatelyÆ; and æif a coal seam is less than 50 cm thick and the parting above or below is thicker than the coal, the coal will be wastedÆ. These decisions are also often made based on the requirement for a minimum sample mass for analysis, and the desire to collect data at the minimum resolution to conserve the exploration budget.In many cases the geological models based on this data are produced at a resolution that is inadequate to allow the mining engineer to produce a mine plan that will maximise project value. This problem is generally unrecognised.Where data is collected to a higher level of resolution the subsequent processes employed in the production of geological models and mine plans often discards the inherent value that is hidden in this data. Again this problem is generally unrecognised.This paper highlights this problem and then presents a methodology that ensures that the optimal working section is selected and compares the outcomes of applying this methodology versus adherence to the usual rules of thumb.

Sep 26, 2011

By M. Krzaninski, Y. Zou, A. Frost

The foundation solution for a data centre building in Sydney, Australia comprised two alternatives, the first of which incorporated the use of CFA piles founded in rock at approx. 27m depth to support column working loadings of approx. 7.5MN, and the second utilising rapid impact compaction with a raft foundation of 1.0m thick concrete slab. Soil conditions comprised 1m of fill over 3 to 4m of sands varying from loose to dense consistency, underlain by very stiff clays overlying the rock. A creative solution incorporating Rapid Impact Compaction to improve the loose soils in conjunction with a piled raft solution was proposed. Piles proposed under the raft were Atlas Drilled Displacement piles which offered advantages of displacement pile performance and savings in time and material costs. The piled raft solution was developed in consultation with the consulting structural engineer, combining the skills of the piling contractor and consulting engineer to the benefit of the project. This paper describes the development and design aspects of the piled raft solution adopted for the project.

Nov 1, 2022

By John R. Gaines

I am not a member of AIME, and this is my first annual meeting. As a lifelong member of the non-ferrous metals industry I have enjoyed listening today to speakers point with pride and view with alarm the public relations activity or lack thereof in the halls of government, as well as at the grass roots. There is much to be alarmed about, to be sure, but also some accomplish¬ments to be viewed with pride. Other speakers have given a broad overview of our industry's relations with their several publics. I will be specific about two incidents in which The Anaconda Company faced the loss of confidence of a large portion of its publics: the nationalization of our properties in Chile in 1971 and the closing of our under¬ground mines in Butte, which was announced last October. If I have a minute left over, I will speak about our concern for the loss of confidence in business institutions which has been re¬vealed in recent public opinion polls.

Jan 1, 1975

By Harry C. Wiess

RECENT announcement of further restrictions on gasoline consumption in the Mid-West and Southwest has focused public attention on current discussions of an oil scarcity. Conflicting arguments are advanced on the one hand that we have plenty of oil and will not need to restrict consumption as soon as transportation facilities are adequate, and on the other hand that a great impending shortage will require most drastic reductions in civilian consumption in order to provide adequate supplies for military purposes. Data can be presented to support both views, the result being that the public is confused and uncertain of where the truth lies. For a nation with about half of the known crude-oil reserves of the world and two thirds of the total production it seems almost incredible to the layman that any shortage can exist. Those familiar with estimates of future demand. however. show increasing concern regarding our ability to meet military demands without further restrictions in civilian use or wasteful production from our remaining reserves. Only by considering such facts as are available and can be made public can a true appraisal be made of whether or not we are faced with a shortage that will amount to a crisis in crude oil.

Jan 1, 1943

By Steven R. Pittman, Colin McCullough, Peter Galuska

"Traditionally Continuous Fiber Aluminum Matrix Composites have been fabricated using high strength fibers and high strength matrices, often commercial alloys, with the goal of producing high strength composites. However the specific role of the choice of matrix alloy on composite properties has not been well established. One way to control composite tensile strength is to use coatings to introduce a low strength interface between fiber and matrix which tends to reduce the importance of the matrix selection, but unfortunately renders the transverse strength unacceptably low. Thus using a system with strong bonding between fiber and matrix is desirable, such as an alumina fiber / aluminum alloy matrix system. In this case the transverse strength is a strong function of the matrix strength. However the longitudinal strength then depends largely on the characteristics of the matrix. The important role of the matrix is discussed using examples of alumina fibers in various aluminum alloy matrices. The key attributes are matrix constituent phases, alloy chemistry, alloy reactivity with the fiber, and matrix strength. From the understanding developed in these systems a set of design rules may be established for selecting an optimum matrix. IntroductionAluminum matrix composites (AMC's) reinforced with continuous fibers offer very attractive property gains over AI alloys, such as strength, stiffness, and fatigue resistance. These gains are magnified when specific mechanical properties are compared which make them attractive candidates for replacing steel, nickel, titanium and aluminum alloy parts in weight critical applications (1). Many systems have been tried in the past; B/AI, C/AI, SiC/AI, Si-Ti-C-O/AI and AI203/AI. Technically B/AI was a very good system but was expensive in regard to both fiber cost and fabrication and SiC/AI and C/AI systems are still plagued with reactivity problems. The Si-Ti-C-O/AI appears to be a good strength system but with lower stiffness. Until recently, the AI203/AI was a low strength system, in part due to a lack of a high strength fiber. Recently 3M introduced a high strength AI203 fiber - Nextel™ 610, which leads to high strength composites (1,2) and may also be both low cost and also compatible with less expensive casting approaches for fabrication."

Jan 1, 1996

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997