Search Documents

By Cheryl Devine, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg

The microbial-mediated recovery of valuable metals locked in mining wastes presents an economical alternative to conventional hydrometallurgical processes. The present study investigated the bioleaching response of a low-grade nickeliferous pyrrhotite tailings (0.6 wt% Ni) and an upgraded pyrrhotite tailings (1 wt% Ni) produced by Vale Base Metals in the Sudbury Basin of Ontario, with the ultimate aim of maximizing Ni recovery. The initial part of the study focused on the bacterial adaptive evolution protocol, by repeatedly sub-culturing an indigenous culture from an acid mine drainage site on 2% (w/v) pyrrhotite tailings. The results showed that the extent of Ni dissolution is positively correlated with microbial activity. Microbial profiling revealed A. ferroxidans to be the dominant member of the microbial consortium. The enriched culture was used for optimizing the growth medium by varying the concentration of essential growth nutrients. Finally, an aerated biotic and abiotic leach of a 10% (w/v) upgraded pyrrhotite tailings with and without pH control, showed a higher recovery of Ni in the pH controlled experiments. These results demonstrate that a high concentration of the oxidant Fe3+ in solution promotes the dissolution of Ni. Furthermore, the sulphide conversion into So was found to be higher in the pH controlled experiments (32%), relative to the experiment without pH control (10%).

Jan 1, 2015

By C. C. Walden, D. W. Duncan, P. C. Trussell

Thiobacillus ferrooxidans released copper from -400-mesh chalcopyrite at a rate of 54 mg/I/hr. Any flotation chemicals remaining on the concentrate did not inhibit the leach rate. Zinc rougher tailings were also leachable. With bacteria, 75 per cent of the zinc and 68 per cent of the copper came into solution. In the sterile controls, only 16 per cent of the zinc and 10 per cent of the copper were released; 100 per cent of the copper and 36 per cent of the zinc were leached from pyrite cinders through the action of bacteria, and 17 per cent of the copper and 10 per cent of the zinc were solubilized in the sterile controls. Less than 0.027 per cent of ~he iron came into solution. The majority of the copper in a converter slag was acid-soluble, but a reverberatory slag responded to microbiological leaching. About 62 per cent of the copper came into solution, compared to 12 per cent in the sterile control. The various factors influencing the rate and extent of microbiological leaching are discussed.

Jan 1, 1966

By K. A. Natarajan, S. Usha Padukone

"An industrial waste liquor having high sulfate concentrations was subjected to biological treatment using the sulfate-reducing bacteria (SRB) Desulfovibrio desulfuricans. Toxicity levels of different sulfate, cobalt and nickel concentrations toward growth of the SRB with respect to biological sulfate reduction kinetics was initially established. Optimum sulfate concentration to promote SRB growth amounted to 0.8 - 1 g/L. The strain of D. desulfuricans used in this study initially tolerated up to 4 -5 g/L of sulfate or 50 mg/L of cobalt and nickel, while its tolerance could be further enhanced through adaptation by serial subculturing in the presence of increasing concentrations of sulfate, cobalt and nickel. From the waste liquor, more than 70% of sulfate and 95% of cobalt and nickel could be precipitated as sulfides, using a preadapted strain of D. desulfuricans. Probable mechanisms involving biological sulfide precipitation and metal adsorption onto precipitates and bacterial cells are discussed.IntroductionIndustrial effluents from hydrometallurgical and mineral processing operations often contain high sulfate and metal concentrations posing significant disposal problems, which require urgent solution to avoid serious environmental contamination. In such waste liquors, sulfate and heavy metals such as cobalt, nickel, zinc and iron originate from the chemical or biological oxidation of exposed sulfide minerals. Reduction of sulfate and precipitation of toxic metal ions from industrial wastes is essential from the viewpoint of environmentally acceptable waste disposal and recovery of associated strategic metals.Many of these heavy metals are essential for metabolic activity of bacterial cells at low levels. But they exert toxic effects at concentrations encountered in polluted water. Removal of toxic metals through biological reduction of sulfates from industrial waste waters have been practiced for several decades. Metal remediation through common physicochemical techniques such as oxidation-reduction, chemical precipitation, filtration, electrochemical treatment, evaporation, ion exchange and reverse osmosis processes is expensive and not suitable in the case of voluminous effluents containing complexing organic matter and low metal concentrations. Further, strong and contaminating reagents are used for desorption, resulting in toxic sludge and secondary environmental pollution. Biotechnological approaches can be more efficient and cost effective for detoxification of such effluents. Biotreatment/ bioremoval offers several advantages over conventional chemical and physical treatment technologies, especially for diluted and mixed contaminants. Biological detoxification, which involves the use of microbes to detoxify and degrade environmental contaminants, has received increasing attention in recent years (Iwamoto and Nasu, 2001). In addition, valuable metals can be recovered from metal sulfide sludge (Boonstra et al., 1999)."

Jan 1, 2015

By John D. Batty

With the emergence ofbiooxidation as a viable process for the pre treatment of refractory gold ores, so have the number of publica­tions on this topic increased dramatically. To a novice in the field of biooxidation, the infonnation presented is often confusing and sometimes even incorrect. Infonnation has also been published that is misleading in that it highlights a particular feature of a process that is either totally irrelevant or of no consequence to the ultimate goal viz. achieving the maximum economical gold recovery. To assist a potential user of biooxidation in evaluating the available published infonnation some guidelines or considera­tions for some of the more important aspects are given, as well as some extracts from publications that demonstrate the manner in which information has been presented.

Jan 1, 1996

By Ross W. Smith

Microorganisms are increasingly finding use in mineral processing and hydrometallurgy both for the enhancement of mineral engineering operations and for the remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of sulfide ores and biooxidation of refractory sulfide gold ores, are established commercial processes. Others, such as the use of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Other uses of microorganisms are potentially possible. These include use of microorganisms in leaching non-sulfide ores, the flocculation or flotation of minerals and remediation of toxic chemicals discharged from mineral engineering operations.

Jan 1, 1993

By D. Raghavan

In recent years, the environmental issues related to the landfill shortage received considerable importance. Many polymeric solid wastes have high resistivity to chemical and biological degradation, and options are sought by which these wastes can be recycled and reused, or reduced in volume. The present study investigated the biodegradation of polyethylene by Aspergillus niger, and biodesulfurization of rubber by pure and mixed cultures of Thiobacillus thiooxidans and Thiobacillus ferrooxidans. The fungus, A. niger, was found to metabolize portions of polyethylene. Quantitative calorimetric measurements revealed that the amorphocity of the sample decreased during biodegradation. Removal of sulfur from synthetic rubber samples containing 2 to 15% sulfur, was studied in shake flask experiments and the associated oxygen consumption was studied in Warburg respirometers. The mixed bacterial cultures were more effective in the desulfurization of rubber samples than the pure cultures of T. thiooxidans and T. ferrooxidans. The data obtained in these studies may have far reaching consequence for the development of new effective processes regarding the remediation and management of discarded polymeric packaging wastes and car tire rubber materials.

Jan 1, 1993

By S. K. Kawatra, T. C. Eisele

"Recent advances in microbiology have made the application of biotechnology to metallurgical processes possible. Hydrometallurgy stands to gain the cost from the use of microorganisms, as they are useful for both dissolution aids and for removing metals from solution. The development of genetic engineering techniques promises to greatly increase the importance of bioprocessing of metals and minerals by the year 2000.In this paper, the basic effects of microorganisms on metallurgical processes are reviewed, and the applications which are currently either in use or near being used are presented. Representative data collected at Michigan Technological University is also given.IntroductionMany hydrometallurgical operations exist which are thermodynamically possible, but which are industrially impractical due to slow kinetics, high reagent costs, or the need for a highly corrosive environment. However, recent discoveries in microbiology indicate that in many cases these difficulties can be reduced greatly by the action of bacteria and other microorganisms (1-8).A major advantage of using living organisms in hydrometallurgy is that once the culture is established the microorganisms produce their own reagents either from the material being processed or from low-cost nutrient supplements. They thus allow extremely complex chemical reactions to be carried out at reasonable cost. The major drawback of using microorganisms is their inability to tolerate extremely high temperatures, excessive concentrations of toxic metals, or very highly acidic, alkaline, or corrosive conditions. However, the complex reactions which bacteria make possible frequently eliminate the need for such extreme conditions. Also, in recent years a number of organisms have been isolated from such exotic environments as hot springs and deep-ocean vents which can tolerate temperatures higher than was previously thought possible for any organism, and can catalyze a number of metallurgically important reactions (8)."

Jan 1, 1988

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

Since the initial discovery of phosphate rock resources in North West Queensland in 1966, significant changes in ownership and development direction have occurred. Initially development of the resource involved beneficiation to produce a more saleable grade of phosphate rock. However more recently development has focused on the production of a high analysis fertilizer product on the minesite. These changes have been influenced by economics, industry/government cooperation and a changing phosphate industry.

Jan 1, 1998

By W. Gibson Jaworek

It has become apparent in recent years to everyone intimately concerned with the future of the American fuels industries that the growth in demand for energy has become a topic receiving considerable attention, and that investigators are leaning more and more toward a mathematical approach to deduce what pattern that growth will follow. Though coal has been included by necessity In all-studies of future energy markets, it has not been the subject of mathematical analysis or description as frequently as has been total energy or some of the other fuels, particularly petroleum, It is the intent in this particular paper, to subject bituminous coal consumption to a preliminary mathematical scrutiny which can lead to a more logical estimation of the general level of bituminous coal consumption for the next decade, as well as formulating an approach toward describing how coal consumption may vary as the result of the annual variations in activity in the United States, economy, The approach utilized is more sophisticated than the mere projection of the historical trend of bituminous coal consumption. Such a projection would lead to a continuation of the recent decline, indicating that coal consumption would reach zero some thirty years from now. On the other hand, the mathematical analysis described here is a relatively simple, straightforward approach and- is not intended to represent the-ultimate in mathematical economic analysis as now practiced, It is hoped that this will contribute to our knowledge of bituminous coal markets. Even more, it is hoped that it will help arouse a greater interestin utilizing mathematical and statistical analysis when studying the bituminous coal industry. - Since this is a preliminary study, comments and criticisms are anticipated.

Jan 1, 1960

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of 'the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By S. C. Ellis

THE bituminous sand of northern Alberta has already an extensive literature, and most of the reports dealing with the subject are still available (see Selected Bibliography at end of paper). A phenomenon so striking and, as regards its extent, so unique, as the deposit in the vicinity of McMurray settlement could not fail to attract the notice of the early explorers, and we find references to it as far back as the latter part of the eighteenth century. However, scarcely a thought had been bestowed upon the possible economic value of minerals in the the remote northern parts of Canada before the second decade of the present century, and practically no detailed mapping had been done north of the town of Athabaska. The late Wm. Ogilvie made a track survey of Athabaska river in 1884, and surveys of certain lines-including the 23rd base line-had been completed by 1911. Between this base line and lake Athabaska, nothing had been attempted. Actually, no definite information at all was available regarding the character and extent of the bituminous sand when, in the earl y summer of 1913, a reconnaissance party set out from Athabaska for McMurray. At that period, the journey was made in summer by scow or canoe. No telegraph line had been laid, and a casual mail service by canoe or dog team once in three months formed the only means of communication with the outside world. The investigation has begun by the Mines Branch was continued during several subsequent years. The sand deposits were studied and sampled, the bi rumen was extracted from the sand and studied chemically and physically, and the economic significance of the deposit was given exhaustive study.

Jan 1, 1937

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By P S. Jaitawat, M Sarim, M P. Roy, P K. Singh, A Joshi

Mining is being carried out using the sublevel open stoping method at the Kayad underground mine. The mine will ultimately reach a depth of 390 m. Kayad village is only 100 m (horizontally) from the underground mining areas. As a result, blast-induced ground vibration is one of the major issues for the residents of the village. This paper deals with the process involved in optimising blast design parameters at the development face blast, slot raise blast and ring hole blast to control blast-induced vibration within safe limits while ensuring improved production, productivity and safety. In total, 1041 development face blasts, 110 slot raise blasts and 52 ring hole blasts were conducted, and 2612 vibration data were monitored in the village at different locations. Initially, electronic delay detonators were used, with an emphasis on controlling vibration in the surface structures. Subsequently, shock tube (Nonel) initiations were used as the blasting faces reached lower depths. A comparative study was also performed for both the initiation systems. The orebody width generally varied from 3.1 to 7 m, and ring hole designs were optimised accordingly. The number of holes in a ring was up to seven and the depth was up to 23 m, depending on the size/width of the orebody. The ring blasts were performed with 64–340 kg of emulsion cartridge explosive and detonated with explosive weight per delay of 10.92–17.16 kg. Extensive experiments were performed and blast-induced vibrations were controlled in the village. Deck blasting (ie up to four explosives decks) was used in a blasthole and the explosive charges were separated by delay detonators, which helped to control the vibration in the village. The actual detonation time of each deck was recorded by monitoring the in-hole velocity of detonation of the explosives, and the charging patterns were optimised accordingly to get the desired blast results.CITATION:Roy, M P, Singh, P K, Sarim, M, Jaitawat, P S and Joshi, A, 2015. Blast design and vibration control at Kayad lead-zinc underground mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 533–544 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Higgins

Measurement while drilling (MWD) techniques can provide a useful tool to aid drill and blast engineers in open cut mining. By avoiding time consuming tasks such as scan-lines and rock sample collection for laboratory tests, MWD techniques can not only save time but also improve the reliability of the blast design by providing the drill and blast engineer with the information specially tailored for use. While most mines use a standard blast pattern and charge per blasthole, based on a single rock factor for the entire bench or blast region, information derived from the MWD parameters can improve the blast design by providing more accurate rock properties for each individual blasthole. From this, decisions can be made on the most appropriate type and amount of explosive charge to place in a per blasthole or to optimise the inter-hole timing detonation time of different decks and blastholes. Where real-time calculations are feasible, the system could extend the present blast design even be used to determine the placement of subsequent holes towards a more appropriate blasthole pattern design like asymmetrical blasting.

Jan 1, 2001

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By Peter K. Strangway

During 1973, a 20,000 net ton (18 100 metric ton) formcoke test was carried out at Inland's 26.5-foot (8.08-meter) hearth diameter on NO. 5 Blast Furnace. The formcoke briquettes were produced from Elko1 coal by FMC at their pilot plant in Kemmerer, Wyoming. The briquettes were shipped to Inland in open railroad cars and most of them were placed in an outside storage field until a sufficient amount was available for the actual blast furnace test. The test consisted of three phases: an initial four-week base period; the actual 33-day formcoke test period; and a final three-week post-test base period. During the formcoke test period, the regular coke skip loads were gradually replaced with skips of formcoke until, after a three-week period, the replacement ratio reached 80%. The furnace operated smoothly and quality hot metal was produced. The burden remained permeable and it was possible to maintain wind rates 9 of over 100,000 scfm (47 Nm3/s) without significant blast pressure increases. Dusting from the formcoke was not a problem either in the stockhouse or in the top gas. The formcoke briquettes maintained their original shape and density as they descended through the furnace. When the 80 percent replacement level had been reached, the inwall temperatures became higher than normal (about 2000 ºF (1090 ºC)) and followed an unusual steady pattern. In addition, the top gas temperature became higher than normal, and the hot metal analyses and temperatures began to fluctuate unacceptably. In general, it is felt that the high inwall temperatures were a result of channeling of the hot furnace gases along the stack walls. This channeling appears to have been promoted by a change in distribution of the burden in the top of the furnace which, undoubtedly, was caused by the increased increments of formcoke. Since it was felt to be unsafe to operate the furnace for an extended period of time with the inwall temperatures at the high level, a decision was made to remove the formcoke from the furnace. When this was done, the inwall temperatures returned to normal. Once the inwall temperatures had returned to normal, the remaining 3,800 net tons (3450 metric tons) of formcoke were used in the furnace at a nominal 40% replacement level for five continuous days. The furnace operated smoothly during this period, and the results were representative of satisfactory furnace operation with partial replacement of regular coke with formcoke. The test was successful in proving that formcoke can replace up to about 50% of the regular coke in a large furnace operating at high wind rates. However, additional work will be required to develop acceptable charging practices for using higher levels of formcoke replacement.

Jan 1, 1977