Search Documents

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By James A. Bachmann, Christopher J. Gray

On December 26, 1994, at 1:00 am, Santa Fe Pacific Gold's Twin Creeks Mine experienced a major highwall failure involving over 2.5 million tons. The resulting effects of this slide were thousands of ounces of gold that were now deferred and an unstable wall above which made mining the slough material unsafe.

Jan 1, 1996

By Stephen Mansfield, Johannes Schoeman

In August 2006 a technical alliance was formed between Orica Mining Services and Century Mine to provide blasting solutions. The alliance is in the form of a Rock to Specification (R2S™) service, one of Orica’s Blast Based Services (BBS™). The ultimate goal was to facilitate the rapid expansion of material movement from 26 to 41M m3 (34 to 53M yd3) per annum while maintaining a reliable ore supply to the mill.

Jan 1, 2010

By Nan Lee, Stephen H. Chung, Peter Lienberger

INCO Limited's Thompson Open Pit has researched extensively into improved blasting techniques towards increased productivity as well as optimum pit wall protection. Blasting with excessive amounts of explosives near the pit wall can induce severe back-break, new cracks and opening-up of existing joints in the wall. These ill effects can reduce the wall slope stability and restrict mining activities.

Jan 1, 1992

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

By Ankit Jha, Javad Sattarvand, Aaron Young

Blockchain technology is one of the prominent disruptive technologies that are being implemented in several disciplines. The application of blockchains in the mining and mineral industry can provide utility to several processes especially when the industry is undertaking digital transformation. The governing principles of blockchain technology are applicable in undertaking transformation in several processes within the mining industry. This study investigates the applications of blockchain technology within the realms of the mining industry and identifies key areas of implementation. A systematic review of publications on academic platforms relating to blockchain technology in the mining industry did not retrieve a considerable number of articles. Consequently, a thorough review of white papers and articles authored by individuals on use cases within the mining industry is compiled and presented in this review article. This review article identifies all the potential areas within the mining industry where blockchains could provide value and improve processes through their implementation. The broad area of implementation of blockchains includes supply chain, traceability in spares parts, contract management, regulatory compliance and cybersecurity.

Mar 1, 2024

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By DALE MacGREGOR, VERA TUREK

The Blue Mountain nepheline syenite deposit has been the subject of several detailed studies. It has been variously referred to as an intrusive stock, a metasomatic deposit, an intrusive sill and a metamorphic-metasomatic body. The body is divided into six mineralogical zones, the first five being based on the characterizing accessory mineral; muscovite, muscovitemagnetite, biotite-muscovite, biotite, hornblende and pink syenite. Mining currently takes place only in the biotite zone. Foliation is particularly prominent in the central (hornblende) zone and near the margins of the nepheline syenite. Majic bodies within the nepheline syenite may represent basic rocks that have been less altered by metasomatism, metamorphosed basic dykes or sloped blocks of metasediments. The most prominent structural features are the northeast-trending folds that have been modified by later north west-trending folds.

Jan 1, 1984

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By Compiled by Staff

"INTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in the public interest to conclude inquiries and scientific and technologic investigations on mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increaseee efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the U.S. Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that: appear in scientific, technical, and trade journals; in "" proceedings of conventions and seminars; in' reference books; and in other non-USBM publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make this kind of list both necessary and valuable.This edition describes reports and articles published during calendar years 1992 and 1993. It supplements the 50-year list of Bureau publications from July 1, 1910, to January 1, 196O 2; and these 5- year lists of publications and articles: from January 1, 1965, to December 31, 1969 4, from January 1, 1970,to December 31, 19745 , from January 1, 1975, to December 31, 1979 6 , from January 1, 1980, to December 31, 1984 7 , and from January 1, 1985, to December 31, 1989 8."

Jan 1, 1994

By Rita D. Sylvester

"This compilation lists and summarizes publications by Bureau authors published in the regular Bureau of Mines series, in scientific, technical, or trade journals, or in other media; those available from the Bureau of Mines are indicated. Patents issued to Bureau personnel are also listed, and instructions are given on how to apply for permission to use them. One of the outstanding features of this Special Publication is an exhausive subject and author index. IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and present their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries, The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminar's; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1970, to December 31, 1974. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;3 and the 5-year lists of Bureau publications and articles from January I, 1960, to December 31, 1964,4 and from January I, 1965, to December 31, 1969.5 It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1970, to December 31, 1973."

Jan 1, 1975

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964

By Shelby Z. Palya

"INTRODUCTION The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mining substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1975, to December 31, 1979. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 3 the 5-year lists of publicatioll3 and articles, from January 1, 1960, to December 31, 1964,4 from January 1, 1965, to December 31, 1969,5 and from January 1, 1970, to December 31, 1974; 6 and the annual lists of Bureau publications and articles from January 1 to December 31, 1975,7 from January 1 to December 31, 1976,8 from January 1 to December 31, 1977,9 and from January 1 to December 31, 1978.10"

Jan 1, 1980

By Mark Sherman

One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client?s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques. Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt?s Grindpower and OMC?s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC?s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics. The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing. The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor?s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved.

Jan 1, 2012

By Godwin J. Igwe

For soil remediation technology to be effective, a thorough understanding of the interactions between a targeted contaminant and the soil matrix is crucial. Proper selection of remediation technology, based on understanding the bonding/binding characteristics of the soil and contaminant, can often result in significant remediation cost savings. Contaminated soil cleanup is complicated by both the physical nature of the soil formation and the behavior of contaminants introduced into the formation. Contaminants can exist in the subsurface in different phase attached to the soil surfaces, dissolved in the ground water, or occupying pore spaces as a separate gaseous or liquid phase. Contaminants properties and how they exist in the subsurface influence their toxicity, mobility and treatability with different remediation technologies A soil characterization study was performed to provide information for remediation technology selection for an inorganic lead contaminated soil. The soil pH, TCLP analysis, thermogravimetric analysis, the soluble anions and cations present, equilibrium leaching tests, analysis by x-ray fluorescence, sequential extractions and speciation analysis using scanning electron microscopy, were all used. Results provided many insights into contaminant behavior in the soil, indicating ultimately whether soil washing or solidification/ stabilization remediation technologies were applicable.

Jan 1, 1994

Satisfactory means of managing growth in boom towns is a concern in mineral, energy and other large industrial developments. This session will include examinations of socioeconomic impacts, major issues such as social disruption, case studies, methods of managing growth, and concerns involving Indian lands. Innovative methods will be offered to assist the public, government, and industry in finding solutions to managing growth in rapidly growing communities.

Jan 1, 1979

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976