Search Documents

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

By M Blanch

Gas management practices across the Australian underground coal industry have evolved significantly since the early nineties with the introduction of hazard management plans, directional drilling techniques, surface gas predrainage methods, and the widespread use of ventilation and gas reservoir simulation software.The improvements are evidenced by a substantial reduction in the occurrence of outbursts and gas related delays during a period where coal production rates have increased three to four fold. The development of effective gas predrainage strategies have been afforded by the use of reservoir simulators and a significant increase in the availability of measured gas reservoir data, in particular gas content and composition, adsorption isotherms and permeability. That said significant opportunities remain to optimise gas drainage designs and increase certainty in the gas predrainage design process through an enhanced understanding of coal seam permeability and how it is applied in the gas drainage design process.This paper describes the discrepancies between measured and actual seam permeability found during the recent assessment of two pilot predrainage programs executed in the coal measures of Queensland’s Bowen Basin. The results of those programs illustrate the need to better understand the validity of measured permeability data. The history match method employed in the pilot well assessments is proposed as an integral step in the routine gas drainage design processes that will ultimately lead to increased certainty and flexibility in gas predrainage practices.CITATION:Blanch, M, 2017. Coal seam gas predrainage optimisation through an enhanced knowledge of coal seam permeability, in Proceedings Australian Mine Vent Conference 2017, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By McCarthy. Richard E.

The prime movers of the Centralia Project, the surface coal mine and the power plant, private utilities are very aware of public attitudes. They have established and maintain the reputation for leadership in public service and are genuinely concerned that this project initiate the pro-grams and design the hardware to answer the question :What will be the impact of the mine and the plant on the physical environment, i.e., the air, soil and the water." So in the beginning almost as soon as the decision had been made to go ahead with the project, officials of the two private utilities, Washington Water Power and Pacific Power & Light went on record and publicly stated time and again that the overall approach of the Operators would be to do all that was reasonably possible to safeguard the environment. This attitude became part of the thinking of the project planners, part of the design of the power plant and part of the plan for the surface mine. The coal to be mined is from the Skookumchuck formation. The formation is Late Eocene and is made up of poorly consolidated marine and non-marine deposits. The major overburden removal equipment is a bucket-wheel excavator -conveyor system and a 56 yard dragline. Mining of the coal will be done with truck and shovel. The coal is processed, washed and crushed to 1 ¼ " for delivery to the power plant. The muddy water created by the washing process is chemically treated and the solids removed by a thickener-vacuum filter system.

Jan 1, 1971

By Brook W. H

The history of the reduction of iron from its ores is lost in antiquity. Archreologists state that man has practised it for over four thousand years. Until comparatively recent times charcoal was the principal reducing agent for making metallic iron from its various oxidised ores. Coke was first used by iron founders in England in 1619, and its use spread gradually throughout the civilised world from then onwards. Indeed, the destruction of forests to obtain the requisite charcoal made the iron founders, both in England and America, extremely unpopular, and this hampered the iron industry to a considerable extent, until coal provided the metallurgist with a new and better fuel--coke which is used by most pyro-metallurgists today. The transition from wood to coal products for iron smelting had a profound effect on the location of iron works. Particularly was this the case in America where, in the infancy of the industry, practically each of the early States had its own iron producers, but as coal and coke replaced charcoal, there came about a concentration of the iron and steel industry around the coking coal deposits, and so today there are huge steel plants clustered around the soft coal basins in Pennsylvania and Illinois.The development of the iron and steel industry in Australia, which is comparatively recent by world standards, has been cradled in the coal basins of New South Wales. The first steel works of any consequence in this country were built near Lithgow, close by the mines which produced the coal for coking.Incidentally, these works were rather unique in that the three essential materials for iron and steel manufacture-ore, coal, and limestone-were found virtually at the works' back door.When, in 1912, the location of the proposed steel works for The Broken Hill Pty. Co. Ltd. for smelting ore from Iron Knob in South Australia was considered, the site ultimately chosen was at Newcastle, almost on top of seams of satisfactory coking coal. One of the major factors which had determined the site of the steel works was the fact that, about 1912, three tons of coal were required to produce one ton of finished steel product, and the relative economics of ore and coal haulage were much in favour of bringing ore to the coal.

Jan 1, 1947

By Gene M. Handel

Today the world is heavily dependent on petroleum for its energy. In the United States, over 75% of the primary energy used comes from petroleum. Other developed countries are similar. The less developed countries have a lower dependence on petroleum just as the United States did through the early 20th Century. However, these less-developed countries look upon petroleum as one of the primary energy sources for the economic growth required to improve their standard of living. So everyone considers petroleum an essential ingredient in the recipe for the good life. But there is a substantial problem with this recipe, and it is finally getting general recognition. Petroleum is a finite resource, and the world is using it up at a rapid, accelerating rate. Though it won't be exhausted for many decades, the early warnings of ultimate limits have already appeared. The suppliers of the incremental production in the Middle East have threatened to restrict increases in their production rates. And, of course, the short term embargo of four years ago clearly demonstrated the economic impact of reduced access to petroleum as a primary source of energy. World petroleum production will probably peak in. 10 to 15 years and then start declining. When that happens, economics--the allocation of scarce products (also known as the dismal science for obvious reasons)--indicates that the price of petroleum will escalate in real terms. So that's the situation today. We have a serious and growing problem facing us that could substantially alter the quality of our life over the next 25 years. Recognition that the society may face a period of lowered expectations after a long period of upward mobility will be a painful experience, but it is certainly not the moral equivalent of war. And, besides, we have time to take positive actions to avert the most serious consequences. When we consider alternate energy sources, the possibilities are almost endless: coal, oil shale, tar sands, solar, fission, fusion, wind, tides, biomass, etc. Actually, the list is endless because new possibilities are continually being proposed. Of these possibilities, coal uniquely stands out as an attractive substitute for petroleum. Coal can be, and is, burned to generate electricity and provide heat. It can be liquefied to supplement the liquid fuels from petroleum, and it can be gasified for use as synthetic natural gas. Unlike exotic alternate energy such as solar and fusion, coal has successfully been used commercially to produce synthetic fuels. But, the technology does need to be refined and modernized. Thus, coal's role is not to be "America's Ace in the Hole," but to bridge the transition from primary dependence on petroleum for energy to the utopia of renewable sources of energy. But don't be mislead by the prophets--those renewable sources of energy are going to be very, very expensive when they are invented.

Jan 1, 1978

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as follows: 1 Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimen¬sion of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of Water 1. A particle will move upward if [W > KVr(s-1)] and, by suitably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [T1= s2-1] cannot be separated in an upward-current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of 2.5 sp. gr. Unless 2.5-1 the ratio of diameters is less than [1.35-1 or 4.3 to 1,] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone¬-shaped vessels or vessels of other shapes that allow the use of&apos; different velocities of current at different points in the flow are used to modify this limitation. 3. During the initial stages of motion, coal particles ascend more rapidly than refuse particles of the same size. 4. A particle will ultimately fall if [W < KVr(s-1).] If particles of

Jan 1, 1950

By M. R. Geer

Coal washing assumed an important role in the mining industry of the Pacific Northwest long before washing practice became firmly established in the Appalachian field. A Scaife washer was operated in the state of Washington in 1887; and by 1927, the fist year for which complete statistics were compiled, nearly a third of the state&apos;s coal production was washed, in comparison with only about 5 pct for the country as a whole. Mechanical preparation was adopted in Alaska in 1922 in a plant constructed by the United States Navy at Chickaloon to provide bunker coal for naval forces operating in northern waters. Many of the coal beds mined in Washington and Alaska contained more impurities than those mined elsewhere, and this circumstance contributed to the early interest in mechanical cleaning. A much more important factor, however, was the inclination of the coal beds. With steeply pitching beds, hand sorting by the miner at the face is impossible; consequently, all material must be loaded and dealt with on the surface, just as is now proving the case with mechanical mining of flat beds. Thus "full-seam" mining afforded the same stimulus to the early development of coal washing in the Northwest that - it is providing under mechanization in the rest of the country today.

Jan 1, 1949

By J. R. Nawrot

Reclamation of potentially acid producing coal processing waste requires a 4-foot cover, and/or treatment to allow vegetation establishment. If not planned properly, soil covering alone does not prevent refuse acidification or formation of acid seeps. Adequate neutralization enhancement prior to soil covering can maintain an alkaline environment in the soil refuse interface and prevent acidification. Direct vegetation establishment using only limestone amendment (without soil cover) can successfully reclaim aged and weathered fine (Blurry) and coarse (gob) refuse if adequate neutralization treatment is provided for the oxidized surface zone. Acid seeps, representing an "after-the-fact" verification of an imbalance of acid-base equilibrium may also be corrected using upslope alkaline recharge techniques. Concentrated alkaline recharge pools have been constructed above previously soil covered acid gob at the Peabody Will Scarlet Mine to abate acid seeps. Preliminary monitoring results (1989-1992) from a concentrated alkaline recharge pool demonstration project in the Pit 4 area of the Will Scarlet Mine have documented a 50 to 80 percent reduction in acidity in the principal recharge pool groundwater zone. A 22% reduction in acidity has occurred in the primary seeps located downslope from the alkaline recharge pools. The initial improvements in water quality are seen as a positive indication that groundwater acidity will decrease further and amelioration of the acid seep will continue.

Jan 1, 1993

By Luis Pommier

In the United States, about one-quarter of the fuel oil and natural gas consumption is associated with power production in utility and industrial boilers and process heat needs in industrial furnaces. Coal has been an attractive candidate for replacement of these premium fuels because of its low cost, but there are penalties associated with the solid fuel form. In many cases pulverized coal is unacceptable as a premium fuel replacement because of the extensive cost of retrofitting an existing boiler designed to burn oil or gas. In the cases of synthetic fuels from coal, research and development still has a long way to go and the costs of research and development are very high. Another option which appears very attractive is the use of solid coal in a liquid fuel form, coal slurry fuels. Occidental Research Corporation (ORC) has been developing coal slurry fuels in conjunction with Island Creek Coal (ICC,) Occidental Petroleum&apos;s wholly-owned subsidiary. Both Coal-Oil Mixtures and Coal -Water Mixtures are under development. ICC is a large eastern coal producer, engaged in the production and marketing of bituminous coal, both utility steam and high quality/low volatile metallurgical coals. A sister division, Sheridan Enterprises is engaged in the development of western coals.

Jan 1, 1983

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia?s underground coal mining industry has reported few new cases of pneumoconiosis for over twenty years. Mortality from Coal Workers? Pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in x-ray surveillance programs are also lower in Australia. To understand this disparity, the National Institute for Occupational Safety and Health was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among United States coal miners. A number of factors, including coal dust exposure, silica exposure, and coal rank were examined as potential contributors to the above observed differences. Comparison of coal rank data from each country did not show any significant differences. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. Assuming that quartz is contributing to the greater number of cases of advanced pneumoconiosis in the U.S., more effective dust control measures, as well an independent exposure standard for respirable quartz in coal mining, need to be implemented to prevent this potentially disabling condition.

Jan 1, 2011

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia&apos;s underground coal mining industry has reported few new cases of pneumoconiosis for more than 20 years. Mortality from coal workers&apos; pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in X-ray surveillance programs are also lower in Australia. The U.S. National Institute for Occupational Safety and Health (NIOSH) was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among U.S. coal miners. A number of factors, including coal dust exposure, silica exposure and coal rank were examined as potential contributors to the above noted differences. Comparison of coal rank data from each country did not illuminate the issue. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. If quartz is contributing to the greater number of cases of pneumoconiosis in the United States, more effective dust control measures, as well as an independent exposure standard for respirable quartz in coal mining, should be implemented to reduce this potentially disabling condition.

Jan 1, 2012

A number of gases, such as carbon dioxide, methane, water vapour, nitrous oxide, ozone and chlorofluorocarbons are transparent to incoming short-wave radiation, but are relatively opaque to outgoing longwave radiation. Variations in the concentration of these gases in the troposphere can alter the thermal balance of the earth&apos;s atmosphere. Outgoing terrestrial radiation which would otherwise escape to space, is trapped within the inner layer of the atmosphere, resulting in a greenhouse effect. It is estimated that at present greenhouse gases other than carbon dioxide, contribute about 50% to the greenhouse effect. However, in the future, the contribution made to the greenhouse effect by gases other than C02 will become increasingly more significant. Greenhouse gases arise from a wide range of sources and their escalating increease is largely related to an increase in the world&apos;s population, an increase in the standard of living of many areas and changes in lifestyle. The effect of increasing man-made greenhouse gases in the troposphere is unknown but it is proposed that it may increase temperature and may modify climate, agricultural response and land use. The sources of greenhouse gases are identified and found to comprise a wide range of activities. The contribution that coals use makes to the greenhouse effect is examined in detail. It is concluded that coals total contribution is small being about 10% of man made greenhouse gases. Envisaged expansion of coal&apos;s use will only cause a small increase in greenhouse gas emissions. Whilst developing technology for coal&apos;s use for power generation has the potential to reduce greenhouse gas emissions from new plants by approximately 25%.

Jan 1, 1989

By A. T. Shurick

THE NRA Administrator&apos;s casual reference to the coal code as the next "pineapple" to be fixed was a conservative estimate of his job. This thorny and adamantine morsel now looms as a critical test of NRA. A failure in coal supplies would have the gravest potentialities in the Administration&apos;s program at this time. And the loss of prestige from a breakdown of the enforcement machinery in this initial large-scale test of strength would accentuate the incipient indications of insurrection in other directions. General Johnson has had a difficult task. It involves problems festering for a quarter of a century. A succes¬sion of Presidents have been glad to tide over their respective regimens with inconclusive expedients; they have been baffled by the complexities of the technical angles and hopelessly irreconcilable concepts of powerful conflicting interests with large issues at stake.

Jan 1, 1933

By J. P. Aiello

"INTRODUCTIONWhile this paper deals specifically with potential coal use at the Cold Lake Project of Esso Resources Canada Limited, a majority of the technical aspects of coal conversion could apply to any oil field and industrial boilers or stearn generators. In 1962, Imperial Oil Limited&apos;s production arm (the forerunner of Esso Resources), began examining methods of extracting bitumen from a 50 m thick layer of oil sand buried 450 m below the surface in the Cold Lake area. Almost two decades of research followed to develop an in situ oil sands recovery technology that made commercial production feasible.A $13 billion mega project that would have produced 22 000 m3/d (141 000 barrels/day) of synthetic crude oil (160 000 bpd of bitumen) was shelved in 1981, and ultimately replaced by a phased development strategy, involving smaller production units, to bring blended bitumen production on stream as markets and prices permit.The first two phases came into production in 1985. There are currently a total of six phases in production with four more in the construction stage. Each phase has 130to 140production wells (initially) and a central plant with water treatment, crude treatment and stearn generating facilities capable of producing 150 m3/d (9500 bpd of raw bitumen). The stearn generation section for each phase consists of three 180millionBtulhour oil fieldsteam generators.In its natural state, the bitumen is too thick to be recovered using conventional oil recovery techniques. At the Cold Lake Project, bitumen is recovered by a method called cyclic stearn stimulation. Water is pumped to the central plant where it is treated and heated to produce high pressure, high temperature steam. During the steam cycle, this steam is transported in insulated pipelines to the wells for injection into the oil sand formation. This cycle lasts from 30 to 50 days, heating the formation and causing the bitumen to flow. Following an initial flowback period, a surface based artificial lift system pumps the heated liquid bitumen, mixed with water and gas, out of the well and back to the central plant. The water and gas are separated from the bitumen, with the gas being used to provide some of the fuel for the stearn generators and the water being treated and recycled. Approximately 5% of the water cannot be recycled and is disposed of by injection into deep formations . The bitumen is blended with a diluent and shipped by pipeline to market."

Jan 1, 1989

By Jiachen Wang, Nan Wang, Yang Li

The energy structure and consumption ratio in China determine the practical demand for the collaborative mining of coal and co-associated resources. The multi-layer mining of coal, uranium, coalbed methane, and oil and gas co-associated resources, represented by the Ordos Basin, Junggar Basin, and Tarim Basin, faces numerous challenges. Additionally, coal has been found to coexist with various mineral resources in 33 coal-bearing basins worldwide. The scientific issues related to the multi-layer development of coal related co-associated resources urgently need to be addressed. This paper discusses the unique challenges and potential solutions in the multi-layer development of coal-related co-associated resources. The challenges include large extraction space, high mining intensity, intense overburden movement, rapid surface subsidence, and severe overburden damage due to repeated mining disturbances. Proposed solutions include the establishment of a correlation mechanism between multi-layer mining and the carrying capacity of the overburden environment, analysis of the impact characteristics of multiple field couplings, and exploration of their superposition evolution laws. The paper also proposes the development of a comprehensive evaluation and prediction system for overburden environmental capacity loss, a global sensitivity analysis model for overburden environmental capacity, and an intelligent identification and early warning system based on multi-source information fusion. These solutions aim to achieve scientific and precise mining with minimal overburden environmental capacity loss. And the multi-layer development of coal-related co-associated resources is a complex task that requires a multidisciplinary approach and innovative solutions, and further research is needed to validate these strategies and explore new methods and technologies for efficient and sustainable extraction.

Jun 25, 2024

"The theoretical basis of ideal smelting reduction using coal as reductant in a process employing closed loop forced-circulation of hot metal is outlined. In the proposed process, an extensive area of relatively slag-free hot metal is available as a heat sink for absorbing the large amount of heat produced by complete combustion of CO within the furnace. Any slag that is formed within the oxidizing arm of the furnace loop is quickly swept away as a thin floating layer by the bulk movement of hot metal which is induced positively by forced melt circulation and sustained by causing the hot metal and the thin slag layer to overflow into a lower level hearth in which coal is carbonised and dissolved directly into the circulating melt.The proposed process is shown to offer very substantial cost savings over all other direct smelting technology. This is mainly because of its inherently low capital cost and its high energy efficiency. Furthermore, the favourable economics are not reliant on fuel gas credits as all the process gas is combusted within the reactor itself.IntroductionMetallurgical processes in the year 2000 will be compromise solutions to the metallurgical problems that already exist today. It is common knowledge that the mineralogical complexity of certain polymetallic sulphides, for example, precludes high degrees of separation and recovery by conventional mineral beneficiation. steps are therefore being taken towards the development of a truly polymetallic smelting process which will produce simultaneously zinc lead and copper as, metals from complex ores without prior beneficiation(l). In the ferrous extraction industry, the shortcomings of the highly efficient modern blast' furnace are well known and world-wide there is considerable effort being directed towards coal-based ironmaking without the requirement of metallurgical coke as a process intermediate. The current status 0f2Joal-based ironmaking has recently been reviewed by Smith and Corbett. (2)"

Jan 1, 1988

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year&apos;s average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

The Energy Authority of NSW has wide powers and responsibilities conferred by its Act which are pertinent to the State&apos;s coal industry and its development into the next century. With respect to coal, the broad objective is to maximise the benefits to NSW and its people derived from the State&apos;s coal resources. The initial focus of the Authority&apos;s coal-related activities in the late 70&apos;s and early 80&apos;s was on petroleum substitutes from coal. Research was supported, especially on hydrogenation, and the Authority participated in the Joint Australia/Federal Republic of Germany coal-to-oil feasibility study. It also co-ordinated a State Government initiative to involve the private sector in examining the possible establishment of a synthetic fuels industry based on Hunter Valley coal. With a short-fall in world-wide petroleum supply now seen as less likely for some years, the Authority is looking also at ways of working towards the broad objective in the field of coal utilisation on both domestic and export markets. Areas of interest include possibilities for using washery rejects, means of making NSW coal more competitive as an energy source, use of coal-seam gas and new or special technologies for burning coal. The future is expected to see renewed interest in producing petroleum substitutes, and coal - as the State&apos;s major energy resource - is seen as a strong contender as a basis for such an industry. Developments in coal-based power generation are also expected to have an impact, with advanced technologies having a possible place here as well as Overseas.

Jan 1, 1987