Search Documents

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

By A. Robison, V. T. McLemore

"The San Juan Basin, New Mexico contains many heavy mineral beach-placer sandstone deposits of Cretaceous age. Beach-placer sandstone deposits are concentrations of heavy minerals that formed by mechanical concentrations (i.e. settling) of heavy minerals on beaches or in longshore bars in a marginal-marine environment. They have high concentrations of several elements, such as Ti, Zr, rare earth elements (REE), Sc, Y, U, Th, Nb, Ta and Fe. These elements are becoming increasingly more important to industry, because they are used in the manufacture of devices our society uses every day, i.e. cell phones, computers, and alternative energy devices, like solar panels. It is unlikely that any of the beach-placer sandstone deposits in the San Juan Basin will be mined in the near future because of small tonnage, low grades, high iron content, and distance to processing plants and markets. However, as the demand for some of these elements increases because of increased demand and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Current studies at the New Mexico Bureau of Geology and Mineral Resources are focused on the Apache Mesa (formerly Stinking Lake) deposit near Dulce, New Mexico. INTRODUCTION Beach-placer sandstone deposits are accumulations of heavy, resistant minerals (i.e. high specific gravity) that form on upper regions of beaches or in long-shore bars in a marginal-marine environment. They form by mechanical concentration (i.e. settling) of heavy minerals by the action of waves, currents, and winds (Fig. 1; Bryan et al., 2007). Modern examples are found along the Atlantic Coast, USA (Koch, 1986; Carpenter and Carpenter, 1991), southeastern Australia (Roy, 1999), and Andhra Pradesh, India (Rao et al., 2008), where they are mined for titanium, zircon, and monazite (a Ce-bearing rare earth, REE, mineral). Detrital heavy minerals comprise approximately 50-60% of these sandstones and typically consist of titanite, zircon, magnetite, ilmenite, monazite, apatite, rutile, xenotime, garnet, and allanite, among other minerals. Most of these minerals have a high specific gravity exceeding 4 and are dark colored, giving the sandstones a dark color, resulting in them being called black sandstones. Although beach-placer sandstone deposits are found in strata of all ages; the deposits in the San Juan Basin in New Mexico are restricted to Late Cretaceous rocks belonging to the Gallup, Dalton, Point Lookout, and Pictured Cliffs Sandstones (Fig. 2; Table 1; Chenoweth, 1957; Houston and Murphy, 1970, 1977). The beach-placer sandstones are black, dark gray, to olive-brown, resistant to erosion, and radioactive due to radioactive zircon, monazite, apatite, and thorium minerals. Anomalously high concentrations of Ti, Fe, Nb, Th, U, Zr, Sc, Y, and REE are characteristic of these deposits. Similar Upper Cretaceous heavy mineral, beach-placer sandstone deposits are found throughout Montana, Wyoming, Utah, Arizona, and Colorado (Dow and Batty, 1961; Houston and Murphy, 1970, 1977; Zech et al., 1994)."

Jan 1, 2016

By Sandin E. Phillipson

"On April 5, 2010 a massive dust-fueled explosion at a longwall mine in southern West Virginia claimed the lives of 29 miners. The mine had experienced large gas inrushes from the floor on two known previous occasions, and natural gas was found emanating from floor fractures behind the longwall shields after the explosion, indicating a likely fuel source for the initial ignition. In succeeding months, another longwall mine operating in the same seam 15 miles away encountered smaller inflows of natural gas that halted production from two different longwall faces. Production was halted at a third longwall mine, 30 miles south of the first, in May 2011, when explosive levels of methane were detected inby the longwall face on the headgate. The same mine was evacuated on March 20, 2014 when a series of floor gas feeders were encountered on the longwall face. A literature review indicated that there has been little documentation or description of these events, and that their size and frequency are unknown. The most significant floor gas inrushes in the United States are believed to have been associated with longwall mining in the Pocahontas No. 3 Seam of western Virginia, in which an estimated 5.8 x 107 ft3 of natural gas was expended from a floor feeder on the longwall face over a two-week period (Aul, pers. comm.).A variety of mechanisms and circumstances are associated with methane emanations from underground mines. Hyman (1987) defined an outburst as a violent, simultaneous release of gas and comminuted rock material into a working face or the interior of a borehole, and indicated that certain soft or fractured coals have a propensity for outburst based on gas desorption rates. In this mechanism, reservoirs of autogenic gas hosted in pockets of soft, crushed coal surrounded by harder coal are released suddenly as confining stress is removed by mining. Hyman (1987) also suggested that highly stressed, relatively gassy coal that is penetrated by mining-induced fractures could be outburst-prone. Clayton et al. (1993) and Ulery (2008) recognized the importance of faults as potential conduits for gas from adjacent strata into coal mines, and suggested that biogenic gas trapped in adjacent strata could migrate into mined coal seams due to a pressure differential. Ulery (2008) distinguished between an outburst and a blower, the latter defined as an event expending a large amount of gas over an extended time period, most often emanating from underlying strata, but without expulsion of coal or rock. Methane feeders are further defined as a subset of blowers that continually expend gas over a long period of time but at a lower rate. Many of the mechanisms discussed by Ulery (2008) relate to geologic features that can impound gas within the seam, releasing a voluminous amount when mining breaches the elastic dike, fault gouge, or other geologic structure that had restricted and compartmentalized coalbed methane migration. Thus, the events discussed in this paper can be described as blowers and feeders. However, detailed geological observations of the three longwall mines discussed in this paper appear to indicate a mechanism that is different from those described by Hyman (1987) or Ulery (2008), in that they did not involve coalbed-sourced gas, and the reservoirs were not hosted by coal seams."

Jan 1, 2016

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By Johannes Jäger

"A composite shell lining typically consists of an outer permanent sprayed concrete shell, a water proofing layer and an inner sprayed or cast concrete shell. Composite shell linings become more and more popular and have been built recently on large scale infrastructure projects. Surprisingly there is very little published literature on the actual structural design of composite linings. As a consequence there is a lack of common understanding on how to design a composite lining structure. Composite action of the outer shell (primary lining) initially carrying short term ground loads and the “unloaded” inner shell (secondary lining) require nonlinear concrete modelling to be able to assess the bearing capacity of the composite lining structure adequately. The composite action of the waterproofing membrane and the inner and outer shells can be considered either by simplified closed form solutions or by numerical models. Strength and stiffness parameters of membrane and concrete govern interaction of inner and outer shell. This paper should contribute to understanding composite lining behaviour with focus on the bearing capacity at limit state by taking into account the actual loading history. Possible ways and concepts on how to deal with these topics are presented, however a broader discussion on limit states of the composite lining materials – also in the long term will be required to come to an agreement on composite lining design methodology. INTRODUCTION Composite Lining Technology Traditionally the construction of shotcrete lined tunnels incorporates primary and secondary linings, separated by a sheet or a sprayable waterproofing membrane. The primary lining shotcrete is considered to be structurally temporary and the secondary lining to be permanent, leading to designs which ignore the bearing capacity of the primary lining in permanent condition. There was general perception that the shotcrete lining installed immediately at the tunnel face, experiencing strains up to 1% and even cracking in the early age, combined with mesh reinforcement additional support measures like lattice girder, spiles and bolts cannot be considered as a permanent structure. But also former shotcrete mixes showed significant weakness with respect to durability suggesting a more temporary nature of primary lining shotcrete. On the other hand it was clear that primary lining shotcrete does not disappear, it may lose probably a certain percentage of its bearing capacity, but discounting any contribution from the primary lining at all was considered inherently conservative. There were different strategies to account for the risk of reduced durability and bearing capacity of the primary lining, either by selecting moderate ground loads for the secondary lining design, by assuming that some residual load will be carried by the primary lining. This approach is very much based on experience. Another more rational possibility is to assume that the primary lining degrades into a rocklike material, which is weaker than the primary lining shotcrete but still imparts some strength to the ground around the secondary lining, but does not need to comply with any concrete design codes any more."

Jan 1, 2016

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By T. W. Camm

"Search Amazon.com using the keyword “leadership,” and you are rewarded with a list of over 144,000 titles. There is no shortage of books and articles, many of them well written, with excellent ideas. So why is there still a constant cry for effective leadership in organizations? Often, the person in charge has personal blinders that prevent them from seeing or understanding how to implement the newest leadership idea or method. Either deliberately or subliminally, there is a disconnect from learning about leadership, and actually modelling and implementing what has been learned. Some current research in leadership theory can provide insight and tools to address this issue. INTRODUCTION Let’s start with a discussion of terms. Pseudo is defined by Webster (2015) as “Being apparently rather actually as stated.” Synonyms include affected, assumed, contrived, fake, false, phony, pretended, and artificial. Antonyms for pseudo provide additional clarity, especially when we consider terms normally associated with effective leadership: genuine, natural, unaffected, unforced. A similar type from my world of academia is a pseudointellectual, “A person exhibiting intellectual pretentions that have no basis in sound scholarship” (Dictionary.com, 2015). This is a person pretending to have an interest in intellectual activities for status; a fraudulent intellectuality. The thought of applying the term pseudo to leadership first occurred to me while reading Power and Innocence by Rollo May (1972). In discussing the dynamics of power, and how the innocent are often victims of the exercise of power, especially the more aggressive and destructive types of power, he saw two types of innocence. The first he called authentic innocence, which he described as a childlike clarity that carried into adulthood. The second type he called pseudoinnocence, a type of naïveté that makes a virtue of powerlessness, weakness, and helplessness; being more childish than childlike (p. 48-50). Just as there is the potential for pseudoinnocence and pseudointellectuals, it is also possible to experience pseudo leadership. (I hope the gentle reader is not troubled by my decision to use pseudo leadership as two separate words, in contrast to the use of compound words for pseudoinnocence and pseudointellectual cited above. Since there is no official definition of pseudo leadership, I have exercised my author’s prerogative to treat it as two words, both because I think in this particular application this makes the most sense, and also I think it is easier to read). As we will see, there are numerous theories applied to leadership. What is so troubling to many of us in organizations, there are a myriad of “leaders” in companies espousing pet theories, but very few instances where the actions of these individuals match their words. This is a particularly important problem when we look at the effect this has on the day to day operations of a mine, and where effective leadership (or its absence) can have a profound impact on both productivity and safety."

Jan 1, 2016

By R. H. Matjie, J. R. Bunt, C. A. Strydom

"A number of conventional and advanced analytical techniques (proximate and ultimate analysis, low-temperature oxygen-plasma ashing, X-ray diffraction, X-ray fluorescence spectrometry, coal petrography, and lightelement electron microprobe analysis) have been integrated and crosschecked to provide detailed characterization of coals from the Highveld coalfield in South Africa, as a basis for better understanding of the mineralogical and chemical properties of the individual coal sources that are blended as feedstocks for combustion and carbon conversion processes. The techniques included methods to quantify the abundance and composition of the mineral matter (minerals and non-mineral inorganic elements), and also the abundance and chemical composition of the individual macerals in the individual coals concerned.Kaolinite is the most abundant of the minerals in the coals studied, with lesser but still significant proportions of quartz, mica and/or illite, dolomite, calcite, and pyrite. Small but variable proportions of anatase, goyazite, and siderite are present in some coal samples. Electron microprobe analysis, based on a special configuration for light-element study, shows that the vitrinite contains less carbon and more oxygen, and has significantly higher concentrations of nitrogen and organic sulphur, than the inertinite macerals in the same samples. Minor proportions of organically-associated inorganic elements, including titanium, were also identified in some of the maceral components.A comprehensive knowledge of the minerals and non-mineral inorganic elements in the coals used for feedstock preparation, obtained by integration of data from these advanced analytical techniques with more conventional analyses, may be of benefit in understanding the processes that take place during coal utilization, and also in avoiding or ameliorating some of the operational and environmental problems that may occur in different sectors of the coal utilization industry."

Jan 1, 2016

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By Verya Nasri, Kevin Akbarpour, Hiva Mahdavi

"The Sheppard East Light Rail Transit (SELRT) project comprises approximately 13 km of new light rail, which will be constructed along Sheppard Avenue East in Toronto. There is a 380 metre long section of the route that will be constructed as tunnel below Highway 404, which is owned by the Ministry of Transportation Ontario (MTO). MTO has published guidelines for tunneling under its highways. An impact analysis was undertaken to predict the surface settlement and angular distortion of Highway 404 resulting from the construction of the twin tunnels. The results were then compared to the performance criteria defined in MTO’s guidelines. As a result of this analysis, it was necessary to request an adjustment to MTO’s current performance criteria. This paper presents details and results of the impact assessment, approaches taken to satisfy the requirements defined by MTO, and provides details of the adjustment permitted by MTO. INTRODUCTION Several major rapid transit projects are planned for the Greater Toronto and Hamilton Area (GTHA) located in southern Ontario, Canada. These projects are part of The Big Move (Metrolinx 2008) initiative, a 25-year, and $50 billion plan aimed at improving regional transportation. Metrolinx, an agency of the Government of Ontario, is now working collaboratively across the region to deliver major Toronto rapid transit projects to the GTHA. One such project is the SELRT. The line will largely run along Sheppard Avenue East on the surface, except for a crossing of Highway 404 where it will be constructed using a combination of open cut and bored tunneling methods. AECOM has been retained by Metrolinx as the Technical Advisor (TA) to develop the Reference Conceptual Design (RCD) and Project Specific Output Specifications (PSOS) for the project. Also, Infrastructure Ontario (IO) is the Co-Sponsor and CH2M HILL is Metrolinx’s Owner’s Engineer (OE) & Project Management Support (PMS) for the new LRT lines. This paper presents information on the tunneling settlement analysis and further work undertaken to satisfy the MTO’s requirements."

Jan 1, 2016

By Elbasher M. E. Ahmed, Indresan Govender

"A mechanistic model of axial charge segregation in rotating drums is presented. We show that granular material composed of different frictional properties diffuse into axial bands as a consequence of concentration fluctuations in the free surface layer that is caused by friction-limited mobility. A Bagnoldian stress assumption ensures an asymmetric free surface profile thereby providing the essential ingredients for the evolution of axial bands and the subsequent band coarsening observed in the literature. The formulation is sensitive to the boundary conditions of tumbling mills, including particle size and density, mill speed, inter-particle bulk friction, end wall friction and drum geometry (length and diameter).INTRODUCTIONA mechanism to fully describe the axial segregation of charge in a rotating drum remains elusive to the mineral processing industry. With regard to low aspect ratio mills (like ball mills), current thinking favours the use of closed circuit mills with correspondingly low residence times to offset the completely random contact probabilities between particles and balls (Wills & Napier-Munn, 2006). Conical end caps are argued to exploit the centrifugal force to achieve a regular gradation of ball size along the mill with larger sizes at the feed end and smaller ones closer to the discharge. However; segregation along the length has been observed in the absence of conical end caps (Oyama, 1939; Levine, 1999): In these investigations, sufficient differences in the particle’s mechanical properties (particle size, density, shape, surface roughness) was enough to successfully achieve axial segregation. Figure 1 shows the segregation of a bimodal distribution (by size) into bands of larger (darker colour) and smaller (lighter colour) particles."

Jan 1, 2016

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016

By G. Viggiani, J. Bel, H. Wong, N. Losacco, D. Branque

"Within the framework of the European project NeTTUN, the Laboratory of Civil Engineering and Building Sciences of ENTPE in Lyon (France) is in charge of a large experimental campaign to investigate the impact of tunneling on neighbouring piled structures. For this study, an original reduced-scale (around 1:10) physical model of EPBS is used. This ""1g"" laboratory model is able to reproduce the main features of the excavation method. For this new experimental program, the miniature EPBS advances inside a large tank filled with a model soil (dry sand), in which instrumented piles were pre-installed. In this paper, the authors describe briefly the original 3D device and present results concerning the impact of tunneling on a single pile located above the tunnel. Different tunneling face pressure are studied in connection with the practice. Machine parameters, pile solicitations and stress-strain behavior of the soil mass monitored under real time conditions are discussed. INTRODUCTION When tunnels are constructed in urban areas, they often come close to pre-existing structures, such as pile foundations. Perturbations of tunnel construction on these neighbouring structures must be considered during design and construction of the tunnel. Ground movements due to tunnelling may induce bending moments, lateral and vertical loads, settlements and lateral deflections in the piles, which may lead to structural damage or failure of the piles or the supported structure. The interaction between piles and a tunnel in construction is a complex three dimensional problem. To date, several experimental approaches have been carried out to analyse the effects of tunnelling on piled foundations (Bezuijen et al., 1994, Loganathan et al., 2000, Jacobsz et al. 2004, Lee and Basset, 2006, Marshall and Mair, 2011, ). These different studies carried out in the laboratory on 1 g or centrifuged models aim at a better understanding of tunnel - piles interaction and a quantification of the influence of each dominating parameter on the structural responses. Parameters like foundation type (single pile, group of piles) and geometry, relative tunnel – pile position, volume loss induced by tunnelling, ground characteristics, pile loading history were considered. However, most of these experiments were carried out under plane strain conditions by modelling the volume loss due to tunnel excavation by decreasing the tunnel diameter or the radial support pressure. As a result, these models do not adequately account for the variations of settlements both in the longitudinal and the transverse direction, which can induce significant flexional and torsional effects on the structures. These effects are particularly critical and detrimental in the case of historical monuments."

Jan 1, 2016

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By H. Ehnes

"“Industry 4.0” – “Mining 4.0” - perhaps you have already heard of these terms? These keywords signify the next stage of industrial production. The internet and production technologies are growing closer together. Machines can communicate with one another, wherever they may happen to be located. The “Internet of Things” is the appropriate term. But what does SAFETY 7.0 mean? It is both brand new and traditional at the same time. It also has to do with the success of companies, with efficient production. And yet there is a great deal more at stake. It has to do with our lives and our safety – the supreme commodity in this world. What exactly SAFETY 7.0 means, what the number 0 stands for and the meaning of the number 7, and what this all has to do with mining will be explained in the following article. Mining is a fascinating undertaking. Mining is indispensable for a country’s economic development, whatever that may concern: infrastructure, energy supplies or raw materials for industrial production. Mining has brought forth many technological developments and innovations that can currently be found in our daily lives. Mining is impressive, grandiose and repeatedly fascinates mankind with its immense dimensions. Miners throughout the world still work hard and, for this reason, are bound to one another in a special way. In mining, every man looks out for the other; you have to be able to rely on each other. That creates a strong bond. The other side of the coin is that mining and disasters belong to normality in the media and thus also in our perception. Accidents at work and even catastrophes occur in mining, quarries, or raw material operations almost on a daily basis somewhere in the world. They are often associated with extremely serious injuries, or even a fatal outcome, for the miners affected and, in turn, dramatic consequences for the families of those involved. It could be in China, India, Russia, or somewhere in Africa, Asia or America – it mostly does not happen in front of our door or in our neighbour- hood. Perhaps because of this in the daily concert of negative headlines, we do not register these catastrophes any more in our minds. We write them off under the heading “Nothing special”, since there are, day in day out, more terrible news items about wars, civil wars, famines, or ecological disasters. Things only really change if there is a dramatic number of deaths or when we are personally affected, close by in the vicinity, or can witness the rescue action live. In Europe, these three mining disasters in particular have recently generated media resonance:"

Jan 1, 2016

By T. Schrauf, J. Scott

"INTRODUCTION Cyanide heap leaching of gold ores in areas with extremely low winter temperatures requires special considerations to prevent freezing of the leach solution. Factors that impact the solution temperature include ore temperature at the time of stacking and during operation, burial of drip irrigation lines, use of geomembrane covers, and heating of the leach solution. Thermodynamic modeling was performed to simulate expected ore and solution temperatures under different operating strategies for Kaminak Gold’s Coffee Gold project in the Yukon Territory. Mean monthly temperatures at the site ranged from a low of -22.5oC to a high of 13.6oC, while in situ ore temperatures ranged from -0.5 to about -1.5oC. The modeling results were used to optimize the operational parameters and indicated that a combination of drip line burial and heating of the leach solution during the winter months was required to maintain solution temperatures above freezing during the initial years of stacking, although as the size of the heap increased, heating was no longer necessary. MODELING OBJECTIVES The successful operation of a cyanide heap leach under extremely cold winter temperatures requires the implementation of operational strategies to prevent freezing of the leach solution and the ore within the heap. Thermodynamic modeling of the heap provides the means to quantify the effectiveness of these different operational parameters on maintaining the required operating temperatures to avoid freezing within the heap. The operational parameters that were evaluated with the model included: • Burial depth of irrigation lines to prevent freezing during the winter months; • Variation in the temperature of the applied leach solution (to simulate heating of recirculated solution); • Variation in the rate of irrigation including seasonal variations between winter and summer months; • Seasonal versus year-round stacking of ore (to simulate the impact of the initial temperature of each ore layer as it is stacked); • Seasonal versus year-round crushing and stockpiling of ore, including the option to stockpile ore on the leach pad in the winter (i.e. stack but not leach fresh ore in winter); • Start date for seasonal stacking; • Variation of the heap geometry over time (both vertical and lateral expansion) and the associated heat storage within the heap; • Use of thermal covers (gravel or geomembrane) over the ore during the winter months; and • Effect of crush size on heat loss during crushing, stockpiling and stacking."

Jan 1, 2016

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016

"Metallurgical process development in greenfield projects must define the comminution flowsheet and establish the equipment sizes that are required to deliver the project design criteria. These are critical steps that heavily influence the financial performance of the project, requiring a detailed understanding of the ore properties of the project resources and the best practice methods to size comminution machines. This paper reviews current practices for determining the ore characteristics relevant to comminution circuit design. Particular attention is given to the design of sampling and testing programs, and the methods commonly applied to size crushers and mills for conventional size reduction applications in mineral processing. IntroductionMetallurgical process development in greenfield projects requires the selection of a comminution flow sheet and must establish the equipment sizes required to deliver the project design criteria. This necessitates a detailed understanding of the ore properties that define the project resource. For brownfield projects the same objectives may apply for plant expansions, or the project objective may be simply to define the capacity and operating cost of an existing facility for a new ore source. The process development phase in either instance will typically comprise the following key activities:• Geometallurgical classification and sampling of the ore deposit or deposits.• Determination of comminution energy requirements.• Benchmarking similar projects.• Identification of flow sheet options.• Equipment selection and sizing.This paper is concerned specifically with process development testing and will as such focus on the first two activities on the list: sampling and testing of the deposit. The discussion will focus on testwork programs to support the design of comminution circuits commonly in use in mineral processing today, specifically crusher, tumbling mill and stirred mill technologies.It is important that any testwork program is designed giving consideration to the types of flow sheets that are viable for the project, and the data that will need to be generated to support the final equipment sizing. Designing a testwork program to only provide information about one particular type of flow sheet will not allow sufficient information to be generated for a rigorous trade-off analysis of options, and may therefore preclude financial optimization of the project. Testing programs should be designed to collect sufficient data to ensure that any backtracking at a later stage to fill in missing information is minimal."

Jan 1, 2016