Search Documents

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By H. R. Manouchehri

"Pyrrhotite (Po) is one of the most abundant sulfide minerals in processing industry and must be rejected in most cases. Particularly, Po rejection and its selectivity against pentlandite (Pn) have long been a challenge due to similarities in the mineral composition of the two minerals and the collectorless flotation characteristics of Po. Xanthates have been widely used to promote sulfide mineral flotation; however, in the presence of xanthates, the redox potential established at the mineral/solution interface is most important, determining the flotation performance. In this paper, the importance of electrochemistry in Po and Pn flotation has been demonstrated and a comprehensive study was conducted on two different feed streams (i.e., magnetic concentrate and scavenger cleaner streams, containing magnetic and nonmagnetic forms of Po, respectively), from Vale’s Clarabelle Mill in Sudbury, Ontario, with an objective to determine if improvements in Po rejection and Pn recovery could be achieved by controlling pulp electrochemistry. By conducting a series of flotation tests under different Eh conditions and reagent usage schemes, it was revealed that higher Po content in the magnetic stream may protect Pn from being oxidized, improving Pn recovery. The results indicated that at low oxidizing pulp chemistry, the rest potential for the Pn is still high enough to allow the formation of dixanthogen to promote its flotation. Using a Pt electrode, it was found that by controlling pulp potential at -50<Eh< +50 mV, the Pn recovery and Po depression would be satisfactory. The results, using mineral electrodes (Outotec Chena analyzer), indicated that selective separation can be achieved if low-to-moderate oxidation potentials (0 to 100 mV) or reduction (0 to -100 mV) potentials are monitored using Pn and Po electrodes. Mixing two streams at 50:50 wt % would be possibly beneficial in selective separation.IntroductionPyrrhotite (Po), Fe1-xS, is one of the most abundant sulfide minerals in the processing industry. It is an iron-deficient sulfide that occurs either in monoclinic or hexagonal form. The monoclinic one is richer in sulfur and is ferromagnetic, whereas the hexagonal Po is poorer in sulfur and has no magnetic properties. In general, the ferromagnetic properties of natural Po increase with increasing sulfur content. Although Po holds significant iron content, it is not used as a feedstock for the iron and steel industry due to the difficulty in achieving complete removal of sulfur. The common availability of iron oxide ores makes the iron sulfides irrelevant for the steel industry."

Jan 1, 2015

By Han Xing, Cui Jianzhong, Qin Ke, Shao Bo, Zhang Haitao

In this paper, a new approach that uses hot-top DC casting process to producing multi-alloy ingots is present. The different type and size of composite and coated ingots (4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm and 4045/3003 coasted ingot with F140mm/F110mm in diameter) are cast by this approach. The macro-morphologies and microstructures of the composite ingots, the temperature distribution and the element distribution in the interface zone were investigated, also and the interface bonding strength was measured. Results show that the solid supporting layer formed on the cooling plates plays a key role in the casting process of composite ingots. The solid supporting layer can prevent the blending of two melts by resisting the impact of alloy melt, which ensures the stable casting process and casting high quality composite ingots, because the contact height is increased using hot-top DC casting. In addition, fabrication and properties of 4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm are reported in detail.

Jan 1, 2015

"The paper treats the spatial aspect of mine sequence optimization. This aspect is revealed in the context of determination of the optimum number of cutbacks of an open pit mine. Cutback mining is a dominating method currently in base\precious metal mining and it is based on a pseudo-economic discretization of the pit space by using advanced pit design algorithms. The result of the implementation of such approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks for maximization of the project value. A mathematical solution of this problem is developed with the utilization of a combinatorial analysis. The solution provides a multi-variant investigation of the optimum mine sequence with the implementation of an author’s method for production scheduling optimization, which uses the Net Present Value as a criterion for assessing the economic efficiency of mine sequencing. A case study is provided for the conditions of a hypothetical open pit gold mine to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the cutback geometry. INTRODUCTION The mine sequence optimization in open pit mining is a procedure that predetermines the efficiency of the production scheduling optimization. From a technological standpoint, the mine sequence optimization deals with two aspects – spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the open pit design problem. Original results on the time aspect of mine sequence optimization are published by Halatchev [2002]. They reveal a wide range of the Net Present Value (NPV) variation for a multi-variant arrangement of mine sequence over time and using a fixed geometry of the cutbacks, which determines the economic potential of a single open pit mine from a deterministic standpoint. The results show a range of NPV variation up to 30% depending on the stripping ratio of the mine. The effect of this variation is mainly due to the implementation of the mine planning principle of waste deferment in the scheduling optimization and using all theoretically possible variants of mine sequence arrangement by the inclusion of the bench sequences over the Life-Of-Mine (LOM) in the production process."

Jan 1, 2015

By J. F. Mack, P. R. Michael, J. M. Shapaka, S. J. Self, M. W. Richmond

"On October 11, 2000, an estimated 306 million gallons of water and coal waste slurry drained from an impoundment in Martin County, eastern Kentucky into an adjacent underground mine. Approximately 230 million gallons of the water and slurry discharged from two underground mine portals and affected over 75 miles of streams in Kentucky and West Virginia. In response to this and several other similar events, the U.S. Office of Surface Mining Reclamation and Enforcement (OSMRE) commissioned an oversight study that evaluates how well state and federal regulatory programs established under the Surface Mining Control and Enforcement Act are ensuring that impoundment operators are minimizing the potential for impoundment-basin breakthroughs. The study focuses on slurry impoundments constructed in the hollows of Appalachia where numerous coal seams and steep topography combine to result in a large number of mined seams intersecting and underlying impounding facilities. Factors under consideration include: (1) full accounting of all mineable coal seams intersecting and underlying the impoundment; (2) identification and accurate location of underground mines close enough to the impoundment to potentially affect its stability; (3) assessment of the stability of coal barriers between the impoundment basin and adjacent mines, and stability of roof rock and pillars in mines subjacent to the structure; (4) determination of the flowability of the impounded slurry when expanding or undermining the facility are being considered; and (5) measures undertaken to reduce breakthrough potential when necessary. The oversight study began in 2012 after program-evaluation criteria were defined in an OSMRE technical position paper. The study is scheduled to be completed in 2017. BACKGROUND The Surface Mining Control and Reclamation Act (SMCRA) authorizes the disposal of coal mine waste by constructing a coarse coal mine waste embankment across a valley and pumping the fine coal mine waste (slurry) into the resulting basin (Figure 1). A concern shared by many engineers, geologists, and mine inspectors familiar with coal mine waste slurry impoundments is related to the common occurrence of underground mine workings adjacent to or beneath the impoundment: the potential for slurry “breakthroughs” into mine works and subsequent breakouts into the surface waterways (Figure 2). On October 11, 2000 a combination of coal refuse slurry and water from the Big Branch impoundment in Martin County, Kentucky broke through into an underground mine and subsequently discharged into the receiving streams. The location of the point of breakthrough, pathways of slurry/water flow within the mine workings, and two points where the liquid exited the mine are shown in Figure 3. An estimated 306 million gallons of water and coal refuse slurry drained from the impoundment into the adjacent underground mine. Approximately 230 million gallons subsequently discharged from the underground mine at two portals."

Jan 1, 2015

By P. James

"INTRODUCTION High sulfate (SO4-2) levels often occur in MIW (mining influenced water) either as the result of oxidation of sulfide minerals exposed by mining activity or by deliberate addition – commonly by sulfuric acid (H2SO4) use in hydrometallurgical leaching activities. Increasing regulation of sulfate discharge is creating new pressure to treat or mitigate sulfate release to prevent its entry into the environment. Current treatments include precipitating as gypsum during lime treatment, filtration separation using membranes such as reverse osmosis and nanofiltration technology, and biological elimination via methods like constructed bioreactors. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform can also remove sulfate from target streams as a byproduct of its usual primary treatment focus points of metal species elimination and/or pH adjustment.[1-6] This powerful new capability can mitigate sulfate contamination and recover the sulfate in a useful and potentially saleable form as a byproduct of improved primary treatments focused on enhancing production or treating waste. This provides a new treatment opportunity and value proposition for lowering overall sulfate consumption/addition or creating new revenue to defray conventional treatment costs. The DEMET Alternative DEMET utilizes a patented electrolytic technology platform employing proprietary dynamic high surface area electrodes in innovative configurations to achieve a variety of novel selective chemistries. DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells. Secondary reactions (Figure 1A) which could also occur at the cathode (plating/electrowinning, precipitation/scale formation, etc.) are controlled through process tailoring and operation parameter selection. Additionally, DEMET‘s innovative dynamic system mitigates potential fouling and electrode occlusion or shorting challenges which could occur when process particulars demand some of these secondary side reactions occur."

Jan 1, 2015

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

"Foreword by Emily SarverAssistant professor, Mining and Minerals Engineering, Virginia Tech, Blacksburg, VAThe Mineral Processing Division hosted its fifth Student Poster Contest during the 2014 SME Annual Meeting and Exhibit in Salt Lake City, UT – and, by all accounts, it was a huge success! This year, the contest more than doubled in numbers of individual entries and schools represented. A total of 30 students participated, including 23 graduates and 7 undergraduates, representing 13 US and international institutions: Colorado School of Mines, Michigan Tech, Missouri University of Science and Technology, Montana Tech, New Mexico Tech, South Dakota School of Mines, University of Kentucky, University of Utah, Virginia Tech, West Virginia University, Autonomous University of Chihuahua (Mexico), UNAL Medellin (Colombia), University of British Columbia (Canada). In addition to constructing their posters, students submitted abstracts and gave short oral presentations highlighting their research. Based on tallied scores from all three components of the contest, the judging panel selected 1st, 2nd and 3rd place winners at the undergraduate and graduate levels, which were announced during the MPD Luncheon on February 26.In the undergraduate division, University of Utah’s Lucas Pich was awarded the 1st place prize for his poster “Solid-liquid mixing studies in lab-scale flotation tank using electrical resistance tomography.” His extended abstract is included in this issue of Minerals & Metallurgical Processing. Joshua Chidester, also of Utah, won 2nd place for his poster presenting “Evaluation of detectors for radiotracer RTD measurement by MCNP.” And Lucas Rojas-Mendoza, of UNAL Medellin, took 3rd place for his poster on “Preg-robbing in Colombian gold ores.”In the graduate division, 1st place went to Caelen Anderson, of the Colorado School of Mines, who also placed in this contest in 2012 and 2013! The 2nd and 3rd place prizes were awarded to Jacob McDonald and Joseph Halt, respectively, both of Michigan Tech. Extended abstracts describing the work of these up-and-coming researchers are also included in this issue.The 2014 Contest was chaired by Emily Sarver (Virginia Tech) and Lisa Schlink (Freeport-McMoran Copper and Gold, Inc.). Aaron Noble (West Virginia University), David Perkins (Derrick Corporation) and Derek Novotny (Eriez) graciously served on the judging panel this year.Special thanks are extended to all sponsors of the 2014 MPD Student Poster Contest, and to all student participants. Please watch for upcoming details on the 2015 Contest. We look forward to seeing you in Denver!"

Jan 1, 2015

By Enzo Palumbo, Joël P. T. Kapusta, François Larouche

In light of the rapid deployment of bottom blowing smelting in China over the last ten years, one has to wonder why it has taken the copper industry so long to adopt ultra-high oxygen enrichment via Savard-Lee type injectors. As early as 1976, Kellogg and Henderson suggested, in their landmark paper on energy usage in the copper industry, that ‘maximum use of oxygen enrichment of process air’ was one of seven ‘energy saving features’ for copper matte smelting and converting. Yet today, shrouded injection and high oxygen enrichment has not been implemented in copper bath smelting outside China and Vietnam. In this paper, the authors explore the reasons why bath smelting processes such as the Noranda Reactor and the Teniente Converter still operate around 40% oxygen enrichment, while the bottom blowing SKS/BBS process typically runs at 65 to 75% oxygen, with all three processes producing white metal. Are there fundamental metallurgical explanations for this striking difference beyond the long-standing skepticism towards high oxygen shrouded injection and its perceived high implementation cost?

Jan 1, 2015

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015

By T. Celik, B. Genc, C. Musingwini

"This paper discusses a new methodology for defining and measuring mine planning software utilization in the South African gold mining sector within an evolving data-set framework. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgyin 2013. In 2014 the data-set was updated with additional and new information. Using the 2012 and 2014 timestamps, a methodology for estimating the software utilization was developed. In this methodology, the three variables of commodity, functionality, and time factor were used to define and measure the software utilization in order to ultimately inform decision-making strategies for optimal software utilization. Using six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation, and Optimization, utilization in the gold sector was measured. This paper presents the methodology employed for measuring the mine planning software utilization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and who want to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2015

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By Jack Young

U. S. Steel Canada Inc.’s Lake Erie Works is the last green field integrated plant to be built in North America. The plant was designed using the best available environmental technology to develop an environmentally friendly production facility. A summary of the technology and measures used in the construction of the plant are summarized in this paper.

Jan 1, 2015

By M. Javier

"The impact of mine closure is perceived through a veil of compliance to human laws and regulations rather than the laws and equilibrium of nature. This perception motivates present research. Understanding the causes and effects of mine closure defines levels of responsibility. This understanding evolves from mine closure&apos;s legacy. Mine closure is characterized in perpetuity by three aspects: Future liabilities; level of technologies for extraction and, usage of mineral resources. These aspects must be updated to a rationally appropriate level. This paper will address the following questions: Will the minerals remaining in the process of mine closure ever be recovered? Will the mine closure inhibit the availability of minerals for the next generation? How many mines are designed to perform a successful mine closure? Do we close the mines or do we close nature? Is it responsible to continue mine closures as we do them today? Is mine closure a complement of mine operations or a contradiction of mining? Do we need to perform mine closures, yet? This paper reviews mine closure practices and principles with the level of responsibility to nature and for the next generation.PREFACE The planet has irreversible issues to deal with regarding the depletion of mineral resources and contamination occurring from human activities. The population increased exponentially to more than seven billion, this high population with its lifestyles, demands a higher supply of minerals. In spite of these conditions, mining is a vital industry to keep ""civilization"" in society. This is evidenced by what we see around us, in that everything ""made"" in society is directly or indirectly due to mining. Hence, mining cannot be avoided or ignored. Society misunderstands the importance of mining in relation to other activities. At this time, mining is fragmented and economically oriented to supply cheap minerals to a market with peculiar characteristics regarding products that could be designed for recycling and stimulate nature’s equilibrium. These issues add important “variable factors” to the equation, when they are considered as parameters for the next generation. It also raises many questions regarding principles and attitudes about morals and ethics exercised in all anthropogenic activities. The industry&apos;s practices have many flourishing paradigms which are subject to a variety of criticisms and observations. Some of these observations will be described in this paper. It is important to clarify in advance a ""normal disclaimer"" about the ""apparent contradiction"" that could take place in the writer&apos;s comprehension when we abruptly ""jump to conclusions"". We must remember that we are profiling the future in an arena that demands a better understanding of solutions to problems created by actual mining."

Jan 1, 2015

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015