Search Documents

By K. W. Harris, K. A. Perry

Reserve depletion in Central Appalachia is continuously creating unique ground conditions for underground coal mines with many of these difficult environments directly attributable to multiple seam mining and/or deeper overburdens. While many empirical studies have been performed in an effort to improve understanding of these problems along with potentially improving safety and extraction, many of the difficulties encountered lie outside of the normal realm of expected behavior. This is often the case when mining in bump prone ground, where additional concerns are introduced and design buffers are warranted. The boundary element software LaModel was used to study three bump events in a deep-cover, multiple-seam reserve located in Harlan county in the Kentucky region of Central Appalachia. This region is notoriously bump prone due to significant areas of deep cover, the presence of strong to massive lithology (such as sandstone), and an extensive history of underground mining that increases the probability of multiple seam interactions. Multiple seam interactions are best understood with respect to site-specific parameters, including both the geological and geometrical components of interburden, overburden and mine workings. Initially, empirical-based approaches (ARMPS/AMSS) were used when attempting to back-analyze the bump events. However, it was recognized that a more detailed investigation was necessary to understand the fundamental causes/conditions associated with the bump events. Consequently, the LaModel study resulted in a mine-specific calibration method for the reserve. With this method in place, enhanced bump prediction throughout the reserve is expected, such that the stability, recovery and safety of future mining may be improved.

Jan 1, 2014

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By F. B. Kuhnow

When performing blasting operations in open pit settings, energy is released and transmitted through the geology. Some negative effects can have significant impacts on mining operations and adversely affect mine production. This technical paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. The paper includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blastinduced ground motion. Based on the results, a set of criteria is provided to implement in current and future mining operations that involve blasting near underground concrete structures. A set of techniques on how to improve vibration levels for safe operations is also presented. Knowledge of particle velocity and wave propagation for site-specific circumstances to determine a safe level of vibration is recommended. Emphasis is placed on making use of electronic detonators and early delay detonators to achieve successful levels of vibration. A dynamic analysis is necessary to determine if vibration from blasting can damage the concrete shaft structure. When reinforced concrete structures are subject to blast loading, both concrete and steel are subject to very high strain rates. As opposed to static loads, when subject to high strain rate loads these materials increase their strength significantly. In fact, they increase by more than 50% for reinforcing steel, by more than 100% for concrete in compression, and by more than 600% for concrete in tension. This finding is of significant importance in mining operations because it allows an increase in flexural capacity of individual members as a result of high strain rates. Therefore, an elevated ground vibration (PPV) or particle velocity is permissible when blasting takes place near concrete structures.

Jan 1, 2014

By A. J. S. Spearing, T. Kostecki, D. Benton

The use of paste backfill in room-and-pillar coal mines in the United States needs to be fully investigated. This paper discusses a series of physical tests that were conducted to examine the support benefits of theoretical paste backfill regimens in Illinois Basin room-and-pillar coal mines, which necessarily included consideration of weak floor conditions. The series of tests included those simulating strong floor conditions, weak floor conditions, under-confined scenarios, and testing of actual coal-based paste backfill samples. The testing indicated that a paste backfill regimen utilizing a minimum backfill strength of 22 psi at a minimum fill height of 50% of pillar height could significantly increase the longterm stability of coal pillars in the Illinois Basin. Considering typical coal wash plant recoveries, 50% fill would be feasible.

Jan 1, 2014

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By K White, R Hardie, J Merritt, B Kirsch, R Lucas

Constructed stream diversions are a common element of mine sites across Australia. A review of constructed stream diversion performance in the Bowen Basin funded by the Australian Coal Association Research Program (ACARP) in 1999 found over 80 per cent of constructed stream diversions failed to meet regulator and operator expectations. Since that time, improvements have been made in the assessment, design, monitoring and management of constructed stream diversions. Fundamental to these improvements has been the development of a better understanding of the regional stream systems and efforts to replicate the natural stream processes in the function and operation of constructed stream diversions.This paper discusses the history of constructed stream diversions through the Bowen Basin in central Queensland recorded in the outcomes of a series of ACARP funded research projects. Further, the paper reports on the outcomes of a current ACARP funded project that has reviewed the success or otherwise of constructed stream diversions in the region. The assessment has compared the performance of diversions that have been designed to replicate and provide for ongoing stream geomorphic processes with those diversions that were designed and built prior to the development of these design improvements. Based on these investigations we have identified design and construction successes and issues requiring further research and management attention.CITATION:White, K, Lucas, R, Hardie, R, Merritt, J and Kirsch, B, 2013. Challenges and opportunities for constructed stream diversions in the Bowen Basin, Central Queensland, in Proceedings Water in Mining 2013 , pp 73-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J L. Kerr, J Beyer-Robson, S Vink

Driven by an increasing need for water conservation, coal mine operators in the upper Isaac River catchment have placed significant emphasis upon the reuse of water. This initiative led to an overall increase in the salinity of mine waters. The ionic composition of this water differs from local stream water in that concentrations of sulfate are higher than average stream concentrations by ten per cent, while concentrations of bicarbonate and calcium are lower. When this water is discharged into ephemeral streams in semi-arid environments there is potential for this increased salinity and altered ionic composition to impact upon the ecosystem processes mediated by micro-organisms in river sediments.We have measured nitrification, denitrification and methanogenesis rates in a series of lab experiments using sediments from Isaac River catchment streams and found that salinity affects these processes in different ways and to different degrees. Process rates were shown to differ seasonally between samples taken from the same location and habitat type and also between different habitat types at the same time and location. Both aerobic and anaerobic process rates were higher in surface sediments and it is likely that this activity is associated with surface biofilms. Furthermore, we have shown that the ecosystem processes we have measured are limited by the availability of carbon in the sediments.The management implications of these findings for mine releases into ephemeral streams will be discussed.CITATION:Kerr, J L, Vink, S and Beyer-Robson, J, 2013. The effects of increased salinity on microbially mediated ecosystem processes in ephemeral streams, in Proceedings Water in Mining 2013 , pp 121-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By B Hannah, M Uriarte, F Labarca, C Madore, G Ganapathi, L Martin, T Haase

BechtelÆs Mining and Metals projects across the globe are executed in remote arid and semi-arid countries where providing even basic water supplies impose considerable challenges. Opportunities for water conservation measures using a Six Sigma initiative were proactively pursued to address the potential business impacts of limited availability of water resources. The initiative investigated areas driving water-optimisation during concrete operations and camp management. This paper details the water conservation evaluation of alternatives and cost/benefit analysis based on current and predicted water usage for development projects. Optimisation of water consumption through institutionalising more prescriptive standards for camp design and defining water conservation requirements have resulted in a new standard specification. Based on our projected mining project workload across the globe, it is estimated that for the period 2012 - 2015, a potential 5.5 M m3 water savings resulting in US$11 M could be realised for construction camps and savings of 4 M m3 of peripheral concrete process water resulting in potential cost savings of US$8 M could be achieved as a result of these revised standards.CITATION:Haase, T, Hannah, B, Ganapathi, G, Martin, L, Madore, C, Labarca, F and Uriarte, M, 2013. Water conservation at construction projects, in Proceedings Water in Mining 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A Woodley, N C. Kunz

A mine site water balance is important for communicating information to interested stakeholders, for reporting on water performance and for anticipating and mitigating water-related risks through water use/demand forecasting. Gaining accuracy over the water balance is therefore crucial for sites to achieve best practice water management and to maintain their social license to operate. For sites that are located in high rainfall environments the water received to storage dams through run-off can represent a large proportion of the overall inputs to site; inaccuracies in these flows can therefore lead to inaccuracies in the overall site water balance.Hydrological models that estimate run-off flows are often incorporated into simulation models used for water use/demand forecasting. The Australian Water Balance Model (AWBM) is one example that has been widely applied in the Australian context. However, the calibration of AWBM in a mining context can be challenging. Through a detailed case study, we outline an approach that was used to calibrate and validate AWBM at a mine site. Commencing with a data set of monitored dam levels, a mass balance approach was used to generate an observed run-off sequence. By incorporating a portion of this observed data set into the calibration routine, we achieved a closer fit between the observed versus simulated data set compared with the base case. We conclude by highlighting opportunities for future research to improve the calibration fit through improving the quality of the input data set. This will ultimately lead to better models for run-off prediction and thereby improve the accuracy of mine site water balances.CITATION:Kunz, N C and Woodley, A, 2013. Improving the accuracy of mine site water balances through improved estimation of run-off volumes, in Proceedings Water in Mining 2013 , pp 267-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By C Gimber

Dust suppression is an important environmental control in most mining operations. The poorest quality water within a mine site is often used for dust suppression since it provides an effective means of reducing the volume of poor quality water. The ultimate fate of contaminants or salinity associated with water used in dust suppression is important to consider for optimising water management and assessing the environmental impact and life span and maintenance requirements of roads associated with dust suppression.The propensity for remobilisation of contaminants or salts depends on a range of factors such as the application rate, climate, road construction, water chemistry and soil geochemistry. This paper describes a typical study approach which could be used to assess the short- and long-term impacts of mine water application for dust suppression. The steps of the study are: reviewing the environmental setting, estimating water requirements for dust suppression, reviewing source water chemistry, developing a mass balance model and assessing the mobility and fate of contaminants with a geochemical model.This approach identifies which salt species are likely to form and whether they are prone to remobilisation. It is possible to quantitatively assess the risk of exporting contaminants or salt from roads and to refine the dust suppression strategy to minimise the environmental risk. The approach can be applied at mine sites to address regulator concerns, aid decision-making and improve the understanding of short- and long-term environmental risks.CITATION:Gimber, C, 2013. Assessing contaminant risk associated with the use of mine water for dust suppression, in Proceedings Water in Mining 2013 , pp 235-240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By R Mann, R Prasad, S Vink, V Nanjappa

The level of salinity that various aquatic organisms can tolerate without incurring any adverse effects is dependent on several environmental and evolutionary factors. These factors include the relative concentrations of different types of dissolved salts in the water that makes up their habitat, the regimes to which organisms are exposed to waters of differing salinity levels (including naturally derived variations), the degree to which an organismÆs life history stages have adapted to salinity, an organismÆs ability or behaviour to avoid adverse levels of salinity and an organismÆs capacity for osmoregulation.Release of saline water into rivers of the Fitzroy catchment has created concern about the impact on aquatic organisms. Not only is salinity itself a stressor on organisms but different ionic compositions will moderate the effects. Ecotoxicology experiments were conducted using artificial saline water based on mine water chemistry using sensitive macroinvertebrates collected from the catchment, as well as a range of laboratory organisms in accordance with the ANZECC and ARMCANZ (2000) guidelines. The 95 per cent ecosystem protection value calculated from species sensitivity distribution derived from the commercial tests was estimated to be ~2.0 mS/cm. For the protection of 99 per cent of the species the salinity has to be reduced by more than 50 per cent to 0.91 mS/cm. The electrical conductivity (EC) values, derived by commercial testing and species sensitivity distribution in this study suggests that salinity contaminant trigger values previously developed using a referential approach for protection of aquatic ecosystems from saline mine water releases in the Fitzroy may be conservative.CITATION:Vink, S, Mann, R, Nanjappa, V and Prasad, R, 2013. Determining the impacts of salinity on freshwater organisms, in Proceedings Water in Mining 2013 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A Horne, Z Graszkiewicz, D Dettrick, R Evan, B Neal

"Most of VictoriaÆs rivers and aquifers are already fully allocated or reaching full allocation. In regions without a well-established water market, access to water entitlements to facilitate new development is limited. In areas with established water markets, mine developers face an undue cost burden in circumstances where they are only planning to consume a fraction of the water entitlements that they purchase. The challenge for water managers is to ensure protection of water resources and other water users without creating an unnecessary disincentive for those types of developments that return most of the water that they take from water sources. The opportunity for development of a mine is explicitly linked to a particular location and must be developed where a resource is located or it cannot be exploited at all. Regulatory arrangements that facilitate development may have a positive impact on economic development, particularly where water availability is a potentially limiting factor. Net volume licensing has the potential to allow increased economic outcomes through improved licensing of access to water. Net volume licensing differs from traditional water licensing in that it authorises access to water on the basis of ænet useÆ rather than æthe gross volume takenÆ. This paper asks under what conditions net volume licensing is likely to be feasible and effective. In particular, the paper examines the information and accuracy requirements to allow net volume licensing decisions to be made. This work is based around five case studies in Victoria that were used to examine the potential for net volume licensing for mines and quarries. Assessing a potential net volume licensing arrangement requires the regulating authority to have an understanding of the inputs and outputs of water to a site. In contrast, assessment of take and use licences consider only a single input. It was concluded that the conditions that lend themselves to net volume licensing include: well understood water inputs and outputs, including appropriate accuracy of information where the location of site water inputs and outputs are the same where the timing of extraction and discharge can be managed to minimise impact on the water resource.A key remaining challenge is establishing an accounting framework that allows net volume licensing under current water resource limits. CITATION:Graszkiewicz, Z, Horne, A, Neal, B, Evan, R and Dettrick, D, 2013. The practicalities of implementing net volume licensing of water use in mines and quarries - a discussion based on Victorian case studies, in Proceedings Water in Mining 2013, pp 241-250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By M Grigorescu, J H. Hodgkinson, H Alehossein

A new framework that collates and interprets pre-existing data to assess vulnerability and ultimately plan to avoid or minimise flood-related risk to infrastructure, people, downtime, environment and revenue has been developed. The æClimate Related Adaptation from Terrain Evaluation ResultsÆ (CRATER) method tested at a coal mine in Queensland, provides semi-quantitative information to assist decision makers when designating investment for minimising vulnerability of mining operations to climate. Here we present the processes involved in this three-step approach that uses pre-existing spatial data of the mine site and local knowledge to build a set of visual tools to assist decision-making. The first step of the process is performing multi-criteria evaluation (MCE) within a geographic information system (GIS) on ranked natural conditions at the mine, such as elevation, slope, drainage, soil and vegetation, which is performed to identify critical flood areas. Secondly, a fault-tree analysis identifies how impact can occur and what options there are for impact reduction. Finally, a resource assessment of the mineÆs capacity to adapt reduces the adaptation options to those most suited to the mine. The results are confidential, but for the purpose of introducing the methodology, we present simplified results, particularly of steps 2 and 3. CRATER can also be used for future æwhat-ifÆ flooding scenarios to identify the most suitable locations for roads, buildings or other critical infrastructure. The methodology is transferable to any mine, series of mines or locations along the mining value chain that have sufficient data, providing a practical decision-making tool to identify æno-regretsÆ actions that not only could reduce downtime after or during an event, but in some cases may enhance production between extreme events. We now plan to test this method at a broader scale, to encompass more than one mine in the analysis.CITATION:Hodgkinson, J H, Grigorescu, M and Alehossein, H, 2013. Climate Related Adaptation from Terrain Evaluation Results (CRATER) - interpretation of pre-existing data for mine site flood vulnerability and management, in Proceedings Water in Mining 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By A Tang, K Ringwood

"Water is increasingly being recognised as a material business risk that many companies are still not well-equipped to deal with. Despite a raft of water-risk focused initiatives, methodologies and guidelines, the challenge of managing the strong link between the technical and operational water issues, along with the growing external challenges and interests in water, remain a significant risk to a companyÆs ability to deliver value.This paper provides an overview of the key lessons learnt from ERMÆs experience of working with companies across a range of water sensitive industry sectors, in particular, the mining and oil and gas sectors, to develop and implement practical approaches to manage business critical water risk. These examples highlight the importance of managing water risk by linking technical and operational aspects of water management - with the longer term strategic and social license aspects. Four key ingredients were identified that are central to providing companies with a leading edge in the successful mitigation of water risk: understanding and evaluating water risk including the technical and operational aspects of water management, plus the longer term strategic and social aspects articulating a strong business case that prioritises water risks and their financial exposure to the organisation constructing a clear roadmap that practically links the water strategy objectives with on-the-ground implementation and action building capacity in the organisation to manage, engage and coordinate on water to mitigate risk.CITATION:Ringwood, K and Tang, A, 2013. Practical approaches to managing business critical water risk, in Proceedings Water in Mining 2013, pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By A Dal-Corobbo, R Zick

The coal mining industry is now faced with new regulatory requirements that limit the discharge of chlorides into receiving streams. To meet these new regulatory standards for treated mine water, a zero liquid waste approach was developed using advanced treatment technologies. The approach described in this paper will generate clean water for reuse in various energy endeavours or discharge to the environment, with no substantial liquid or solid waste from the treatment process leaving the site.CITATION:Dal-Corobbo, A and Zick, R, 2013. Zero liquid discharge in coal mining operations, in Proceedings Water in Mining 2013 , pp 221-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A D. Price, W J. Germs, O Patterson, T R. Weaver

"Understanding controls on groundwater and surface water flow and quality at mine sites throughout all mine stages is critical to effectively manage environmental impacts over the entire mine life. Monitoring forms is an essential component of this proof of understanding. Typically, monitoring programs at mine sites have been developed in the framework of existing conditions. However; recognition of the challenges of climate change and the performance of mines during recent extreme events in Australia has highlighted the need to develop monitoring programs that are resilient and responsive to changing environmental conditions. Water monitoring programs need to be effective under a range of environmental conditions, potentially not historically experienced.This emerging challenge requires cross-disciplinary teams to work together to understand issues including: representativeness of background conditions to longer-term conditions at the mine site sensitivity of mine and closure designs to changing climate and hydrologic conditions methods of performance (eg water quality or quantity) failure during extreme climate events such as flood or extended drought.These understandings come together in a detailed conceptual and, in many cases, numerical hydrologic model that considers the mine-water environment under a range of conditions. The groundwater, surface water and water quality monitoring programs that are developed from the conceptual model need to be sufficiently responsive to be effective in the face of such changing conditions, with results in turn informing the conceptual model. Extended drought, major floods and changing weather patterns can alter recharge and discharge areas, oxidation profiles and ultimately, the contaminant flux estimates that would have contributed to mine design parameters and performance. Unless these effects are considered in the spatial and temporal design of the monitoring program and within the parameters monitored, the resultant program may fail to capture data that are critical to evaluating environmental impacts from mine sites.Developing and implementing a water monitoring program that considers these issues can build confidence in mine performance under a range of conditions, leading to increased confidence by all stakeholders in long-term mine performance during and after closure.CITATION:Weaver, T R, Price, A D, Patterson, O and Germs, W J, 2013. Developing resilient water monitoring programs in changing climate conditions, in Proceedings Water in Mining 2013, pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By H He, S Tillotson, S Gibbons, J Shaw

"Water evaluation and management during mining exploration and operational activities is crucial to minimise direct and indirect operational costs and also in delivering mining companies the less tangible, but equally critical æsocial license to operateÆ.Mining is often carried out in remote areas, where the mine will be the most significant and visible user and potential contaminator of water resources. However, wherever it is located, a mineÆs use of water must be managed in the context of two key aspects: the natural parameters of the resource; its abundance, its temporal variability and its chemical and physical qualities other users of the resource; other industry, potable water supplies and ecological requirements of local habitats.It is vital, therefore, that this commodity be assessed to an appropriate degree to help establish the viability and sustainability of the mining project and identify those other stakeholders who may be affected by the mining companyÆs activities.This paper outlines the background to catchment-scale model and presents a cost-effective method for establishing a robust water baseline and creating a water management tool to be used throughout whole mine life cycle. Numerical surface and groundwater modelling has long been established as a tool for reactive management, following collation of yearsÆ worth of data. Now, using freely available remote sensing data and desk study information, analytical modelling techniques can be used cost effectively to provide mining companies with a tool for assessing and managing their water consumption requirements at the outset of a new project venture.The paper includes a selection of case studies to show how the use of analytical modelling can be used as an evaluation and management tool to help not only assess general watershed parameters and water availability but also how it can be used as a tool to provide decision makers with the information to complete æwhat if?Æ scenario assessments. The case studies illustrate how a combined hydrological and hydrogeological model may enable identification of sensitive receptors, water competition issues and contaminant migration pathways to help manage the risks associated with water consumption and its potential contamination from exploration and operational activities.CITATION:Gibbons, S, Shaw, J, Tillotson, S and He, H, 2013. Catchment-scale water modelling and its role in risk management during mining exploration, in Proceedings Water in Mining 2013, pp 175-188 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By B. A. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformation. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, timelapse point clouds of mine workings. In order to determine sloughage volumes and locations, two sets of laser scans were performed 42 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds. Volumetric changes of 2.3-2.6 m3 were detected on rib faces during the time-lapse study. In addition, displacement in the mine roof was, as expected, not detected, suggesting well surveyed scans and an appropriate scan resolution.

Nov 1, 2013

By R. Benito

The publication of the Lerchs Grossmann paper in 1965 outlining a threedimensional graph algorithm for ultimate pit definition set the standard for the mining industry regarding pit optimization. Although the algorithm provides a solution from a static standpoint (i.e., assumes instantaneous mining), it is widely used for commercial packages to generate ultimate pit limits and intermediate phases. However, the solutions delivered are presented in canned reports lacking connection to the original data, which prevents further data analysis and extended reporting. The approach presented in this paper attempts to overcome such barriers by performing openpit optimization through databases. An adaptation of the Lerchs Grossmann graph algorithm is used to generate nodes, arcs and tree structures in customized tables to determine the maximum closure of a graph.

Nov 1, 2013