Search Documents

By K. Scholey, S. Marcuson

As high grade nickel sulphide ores are being depleted and with the continuing challenges experienced in economically processing nickel laterite ores, it is important to investigate technologies that can extract nickel from low grade ultramafic ores which are present in large quantities worldwide. In the Thompson Nickel Belt, there are some hundred million tonnes of mineralization that are potentially amenable to surface mining. Since the original discovery of the Thompson orebody, recovery of nickel from these ultramafic deposits has been an elusive goal. Research and development projects as well as commercial processing have been attempted. In the 2000's as other resources became scarcer, a major drilling, mine evaluation and research project was initiated at Vale. In 2007, Vale Base Metals Technology Development invited Cytec and potential academic partners to participate in an industry-university research consortium with the goal of developing new technologies and methods of processing the ultramafic deposits. Three university professors, J. Finch of McGill, P. Somasundaran of Columbia and R. Pelton of McMaster accepted, each group attacking the problem with a different approach. This paper describes the management of the research consortium and the significance of the results from Vale's perspective. The next four papers in this session will summarize the project and results from the partners' point of view. Vale is pleased to share the experience of the collaborative research and development with the mining industry.

Jan 1, 2011

By Tapan Goswami, Stephen Jeric, Geoff Brent

Highwall failures in large deep open cut mines have very significant safety and commercial implications. There are many factors influencing the stability of highwalls. The major influence is the interaction of the local geology with the shape of the pit wall. This factor is in the realm of the geotechnical engineer and is beyond the control of the blasting engineer. However, a secondary influence is the blastinduced damage to the wall. In most open cut metal mines the blasting strategy to control this damage involves the use of separate production and trim blasts bounded by presplits at the final wall.

Jan 1, 2011

By Timothy C. Siegel

A piled raft refers to a shallow foundation that is structurally connected to the piles, while composite ground refers to a soil-pile matrix where the piles are not structurally connected. The design objectives for both a piled raft and composite ground are (excluding special considerations such as expansive soil): (1) to provide a sufficient ultimate resistance and (2) to distribute the load into the soil-pile matrix so that the settlement experienced by the shallow foundation is within tolerable limits. A simplified model is proposed for a shallow foundation on composite ground where the foundation settlement is estimated as the sum of the downward movement of the piles plus the downward movement of the shallow foundation relative to the pile head. The proposed simplified model is applied using conventional geotechnical analyses for two hypothetical examples of shallow foundations undergoing compression settlement.

Jan 1, 2011

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermo-physical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at the University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous case is modeled with walls, each having a different set of thermo-physical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By W. Hardtke, B. Perry

Model reconciliation problems at the low-grade, high-nugget Phoenix gold-copper deposit led to an examination of the influence of production decisions on ore-waste classification. A conditional simulation study of the deposit was used as the basis for: 1) quantification of dilution at different bench heights, 2) quantification of ore-waste misclassification relative to bench heights and cut-off wades, and 3) determination of an appropriate number of samples to optimize ore-control polygon definition. Actual reconciliation data were empirically used to support conclusions. Simulations of both gold and copper were combined through net revenue modelling. These simulations increased understanding of the nature of the deposit and provided insight for resource modeling and mine planning.

Jan 1, 2011

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By B. Wasmund, B. Haneman, G. Sheehan

Success in implementing new technology for metallurgical processes is not a foregone conclusion: This paper includes a survey of 23 new technology-based metallurgical plant start-ups, in which the authors have identified 7 successes, 9 difficult start-ups, and 7 failures. Success is defined not only as meeting the schedule and budget to the end of mechanical completion; the key goal is a fast ramp up to the full design production level, with minimum plant and equipment modifications required after start-up. This paper sets out the key factors that underlie achievement of a quick production ramp up curve, as determined from the authors' project experiences and a quantitative analysis of over twenty metallurgical plant start-ups, both pyrometallurgical and hydrometallurgical. Thorough test-work and pilot plants, plus appropriate scale-up to the full commercial plant, are key determinants of success in implementing new technology in metallurgical processes. Another critical factor is the number of new elements and their interactions. Project phasing is also particularly important for new technology projects, with appropriate review after each phase to develop a risk mitigation plan for the subsequent phase. New technology projects need committed champions to advance the project in the face of sceptics, but also require dispassionate and unbiased experts to ask the hard questions. As a project evolves, it is important to periodically question the appropriateness of assumptions, as well as to re-assess the relevance and completeness of data from test-work I pilot plants I industrial analogues. Sufficient human and financial resources are required to complete the often arduous implementation phase. During the ramp-up period, the operation generates little positive cash flow; however, significant expertise and capital are required for the de-bottlenecking projects that are often necessary to reach the plant's design output level.

Jan 1, 2011

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study of ten existing or proposed port sites in Alaska, the Bureau of Mines examined the potential for mineral development around three Alaska port sites: Iliamna Bay, Kotzebue, and Nome. The mineral deposits near Iliamna Bay include gold, copper, and iron. Development of minerals in this area will require the discovery of new deposits or the definition of additional are reserves at known deposits. The mineral deposits near Kotzebue are primarily gold, copper, coal, lead, and uranium. Based on the character of these deposits, it appears that development of a small-scale mine supplying coal for regional use is the most likely scenario in the near-term. The mineral deposits near Nome are primarily gold and copper. Development of small underground gold mines is possible, however it appears that expanded offshore gold dredging will have the greatest impact on the flow of freight and goods through the Nome port in the near term.

Jan 1, 2011

By Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Denise Cristina Oliveira Nascimento, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The piassava fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of polyester composites reinforced with piassava fibers with thinner diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned piassava fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, individually separated fibers with the smaller diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinner piassava fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionA significant change in the transportation sectors mainly the aerospace and automotive, occurred last century with the introduction of stronger and lighter materials. The most relevant example was the polymer composite reinforced with synthetic fiber. They are nowadays replacing conventional materials such as the aluminum alloys in airplane body owing to superior specific strength. in recent years, however, environmental problems in a global scale are imposing a reversion in the use of synthetic fiber specially the glass fiber. In spite of its higher specific strength, this fiber and its polymer composites can neither be recycled nor incinerated in a thermal plant to generate electricity [1]. Moreover, the fabrication, processing and transportation of a glass fiber composite are associated with C02emission, the major responsible for global warming [2].A possible substitute for glass fiber without the above-mentioned environmental problems, could be a natural fiber. In fact, natural fibers obtained from cellulose-rich plants, also called lignocellulosic fiber, are already being used in several engineering fields, particularly the automobile industry [3-6]. Figure 1 illustrates an automobile and its many components made of lignocellulosic fiber composite [7]."

Jan 1, 2011

By James C. Barker

In 1981 and 1985-1986, the Bureau of Mines conducted orientation studies of marine placer platinum-group metals (PGM). PGM are derived from the Goodnews Bay ultramafic complex and magnetic surveys show that the complex extends offshore at least four mi. The present seafloor was an emergent foreland as recently as 8000 years ago. High-energy ocean processes are transporting and depositing sediment such that PGM-bearing materials are reworked and later masked by barren littoral drift. Exploration targets include 1) placers formed since present transgression began, and 2) ancient marine and drowned fluvial deposits. Additionally, there is evidence of PGM solution transport and accretion. At least minor values of PGM in Recent lag-type placers and possible submarine strands are concentrated along an offshore scarp incised through glacial deposits into the preglacial surface between Flat Cape and Red Mountain. Other Recent PGM-bearing features include Flat Cape shoal, Chagvan Bay, Salmon River delta, and modern beaches. Ancient placers include possible N-S fluvial systems 2 to 3 mi offshore, a nearshore scarp 50 ft below sea level, and strands adjacent to projected ultramafic bedrock slopes. The existance of ancient placers is dependent on depth of glacial erosion. SEM studies show PGM are principally isoferroplatinum and osmiridium, with minor sperrylite, moncheite, and platiniridium. Gold is a co-product, and concentrates comprise chromite, ilmenite, and magnetite. Beneficiation tests successfully concentrated precious metals from natural blacksand accumulations, but failed to concentrate low-grade lag gravels.

Jan 1, 2011

By K. Morsi, S. K. Kassegne, A. El-Desouky, K. S. Moon

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based fabrication of macro, micro and possibly nano-scale features and shapes. This new and unique process enables selective sintering of powders by localizing electrically activated sintering conditions through a stationary or moving electrically conducting tip. We present preliminary experimental results on the effect of tip size in the CA TS process as well as the effect of initial powder particle size on the sintering behavior of nickel powder.IntroductionSpark Plasma Sintering (SPS) has been the center of attention of numerous researchers due its noticeable advantages over conventional sintering techniques such as rapid heating rates, lower sintering temperature and shorter holding times. Research on SPS has been applied on a wide variety of materials such as pure metals [ 1], ceramics [2], composites [3], nano-materials [ 4], biomaterials [ 5], shape memory alloys [ 6] and many other material systems. However, it has been mostly limited to bulk materials with simple shapes with a few exceptions ofresearch efforts where the effect of electric current was combined with metal forming processes such as spark plasma extrusion [7,8] and electric rolling of powders[9]. In this paper a novel process (Current-Activated Tip-Based Sintering (CATS)) is discussed where electric current and pressure are applied simultaneously through a small conducting tip (stationary or moving) over a conducting powder compact. This process has the potential advantages of sintering complex geometries with minimum energy requirements as unconventionally high current densities can be achieved due to the small contact area between the tip and the powder compact. Furthermore, by controlling the tip size, it can be possible to sinter features on the macro-, micro- and even nanoscales."

Jan 1, 2011

By S. Mathieu, R. Mennillod-Blondin, P. Cousin, N. Valle, H. Bouzahzah, P. Marion

The gold deposit of the Lapa mine has a complex mineralogical gold state with coarse and fine native gold, aurostibite and submicroscopic gold within arsenopyrite. A specific mineralogical characterization of the refractory fraction was conducted combining various techniques such as optical microscopy, electron microscopy, electron microprobe and secondary ion mass spectrometry. In parallel, the mineral processing behaviour and the recovery of the refractory gold were studied by pressure oxidation and cyanide leaching. This paper presents the mineralogical methodology developed to characterize the refractory gold distribution within arsenopyrite. These results are presented and interpreted in order to plot gold recovery versus sulphide oxidation. The comparison of the metallurgical behaviour yields predicted from the mineralogical data and the one calculated from leaching tests shows a good agreement and allows mineralogical explanations of the gold metallurgical behaviour.

Jan 1, 2011

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Jozef Zmik, Sergey Dobatkin, Martin Fujda, George Raab, Libor Kraus

"The present work, likewise, deals with grain refinement of medium carbon steel AISI 1045 having different initial microstructure resulting from thermal and/or thermomechanical treatment (TM) applied prior severe plastic deformation. In case of TM treated steel, structure refinement was conducted in two steps. Preliminary structure refinement has been achieved due to multistep open die forging process which provided total strain Eef ~ 3. Uniform and fine recrystallized ferrite structure with grain size of the order of 2-5 µm and with nest-like pearlite colonies was obtained. The further grain refinement of steel samples having different initial structure was accomplished during warm Equal Channel Angular Pressing (ECAP) at 400°C. The microstructure development was analyzed in dependence of effective strain introduced ( Eef ~ 2.5 - 4). Employment of this processing route resulted in extensive deformation of ferrite grains where mixture of subgrains and ultrafine grain was found regardless the preliminary treatment of steel. As straining increases the dynamic polygonization and recrystallization became active to form mixture of polygonized subgrains and submicrocrystalline grains having high angle boundaries. The intensive straining and moderate ECAP temperature caused the partial cementite lamellae fragmentation and spheroidization as straining increased. The lamellae cementite spheroidization was more extensive in TM treated steel samples. The deformation behavior of for both steel structural state confirm the strength increase; however the work hardening behavior was modified with respect to initial structure of steel prior SPD processing.IntroductionIn the last years, ultrafine grained materials have attracted considerable research interest because they tend to possess high strength without sacrificing toughness and ductility. Microstructural refinement of steel is usually achieved by alloying and/or by thermomechanical treatment process, which modifies phase transformation. Recently, advancement of severe plastic deformation (SPD) techniques provides another efficient access for grain refinement of metals and alloys. The fabrication of bulk materials with ultrafine grain sizes has attracted a great deal of attention over the past two decades because of the materials' enhanced properties [ 1, 2]. In last decade a worldwide effort in manufacturing process to obtain ultrafine grain structures in steels is persisting."

Jan 1, 2011

By Jason H. Nadler, Jason A. Kulpe, Stephanie J. Lin

"A numerical method has been developed to predict the microstructural characteristics of reticulated metal foam. The porosity of this foam is derived from sacrificial template particles of known particle size distribution, which are incorporated with other precursor components. In this approach, a porous structure is numerically generated starting with Powell's sphere packing algorithm. The resulting stochastic structure has characteristics similar to those of corresponding metal foam. Deterministic inter-sphere connections are calculated to more accurately model the pore morphology that evolves during thermochemical synthesis. Estimations of pore morphology and specific surface area of the simulated material are compared to lab-synthesized materials composed of equivalent constituent compositions. In addition, the effect of template particle size, inter-sphere connections, and the geometric constraints on pore morphology and permeability are investigated to refine microstructural evolution and design.IntroductionReticulated foams, characterized by their interconnected pore network, can be obtained by incorporating spherical sacrificial template particles into precursor materials followed by template removal processes. The resulting structure is composed of contiguous spherical pores whose morphologies reflect those of the original templates. Based on some of the unique features of this synthesis approach, a methodology is introduced in this work whereby these foams are digitally constructed using experimental data from the template particle sizes and precursor formulation. Digitally constructed porous structures can then be compared to their laboratory synthesized counterparts through the quantification of structural features such as porosity and surface area per unit volume, which in tum are used to inform the foam's fluid transport propertiesThe spherical template particle packing algorithm developed here is adopted from Powell's work [1], which also includes approaches to obtain percolation and density in random packings [2]. Gervois gives a mathematical development for the stereological sectioning of packed hard spheres [3]. Stereological sectioning facilitates determination of relevant three dimensional morphological properties from two-dimensional data [4]. Studies on the sphere distribution size and the related particle packing density and coordination number results are studied in [5, 6]. Lastly, Kato describes a sintered neck structure, which is used with these packings [7]. This neck structure, as a model of the particle shape following heat treatment, is implemented here in a similar manner. A strong difference between the available literature and the methodology here is that spheres are packed to ultimately represent porous space, not rigid solid space."

Jan 1, 2011