Search Documents

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By B. Broms

The "Bawang Pile" (in english "onion" pile) described in the article consists of a cased concrete shaft and an expanded base. The steel casing is first driven by an internal drop hammer and then the base is formed in-situ by the raming the concrete at the bottom of the slitted casing. This new type of pile can be used for underpining (small head room) of buildings and as foundation for transmission towers or lamp posts. Full-scale load tests in compression and in tension on the Bawang pile and on steel pipe piles demonstrate the dramatic increase of the ultimate capacity due to the expanded base. Guidelines for the design of such piles are proposed.

Jan 1, 2010

Australia is a hub for mining technology development. The paper describes many of the key players involved in mining research in this country along with some of the interesting research outputs to emerge over the past decade.

Jan 1, 2010

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By J. T. Carlson

Dolomite is an objectionable impurity in phosphate ores, due to its MgO content. Even though dolomite and apatite liberate at a coarse size, the very similar densities of dolomite and apatite makes density separations difficult. However, if operated correctly, jigging can be a very efficient process. This has led to the development of a unique laboratory scale jig that allows for easy alteration of effective jigging properties. Key jigging parameters have been investigated for the separation of dolomite from phosphate ores. It was found that a pulsation rate of approximately 200 pulses/minute worked best for separating dolomite from apatite.

Jan 1, 2010

Exxaro installed their first ultra fines treatment plant at Leeuwpan Coal mine. The plant is now fully operational and results already show that the plant has great potential. The plant was designed and installed by DRA. Several challenges were faced during the installation due to the space constraints in the Leeuwpan plant. Efficiency tests were conducted on both modules after commissioning and showed very promising results. A lower ash product with a higher yield can be produced with the fine coal dense medium cyclones compared to the spirals previously employed.

Jan 1, 2010

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flat jack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the support elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 2010

By Jeremy G. Kress

We propose the discrete element method (DEM) as a complimentary alternative to analytical solutions and FEM models for the analysis of pile response. DEM is a novel approach to the engineering design of deep foundations which can be used to provide insight into the mechanics of soil-soil and soil-structure interaction. It is common to use analytical, empirical, and semi-empirical methods to predict pile behavior, where if granular properties, pile length, or load orientation change, then significant adjustments are made in the design sequence. DEM provides a more uniform approach in granular soils. Based on constitutive force-displacement relationships and laws of motion in rigid and elastic bodies, few changes must be made for a wide variety grain types, pile types, embedment, and load orientation. Preliminary results for simulation of a single pile are qualitatively consistent with results from conventional design procedures and also provide significant information not available from other analyses (e.g., local information about interface failure during shear). Importantly, these analyses are portable to a variety of pile types and installation procedures, which may not be the case for empirical approaches. Given consistent increases in computing power and rapid advances in model speed and sophistication, the DEM should prove to be a robust method for design and the analysis of pile response in granular soils.

Jan 1, 2010

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By Michael R. Yenchek

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were undertaken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 2010

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By S. Rajendran

Gas Hydrates (Methane Hydrates) are solid, ice ? like substances composed of water and natural gas. They occur naturally in areas of the world where methane and water can combine at appropriate conditions of temperature and pressure and are found in the ocean bottom sediments and in some permafrost areas. Besides temperature and pressure, factors like bathymetry, sediment thickness, sedimentation rates, and total organic carbon content (TOC) also control gas hydrate formation in the sea. The stability of gas hydrates depends on the critical high pressure ? low temperature combination (0-17 bars, 0-25ºC), which in turn dependent on the mix of gases from which the mineral is formed. As the critical parameters can be altered by deposition, erosion or slumping of sediments, formation or melting of ice cover, rise and fall of sea level and sudden temperature changes induced by tectonic activities, current flows or volcanisms, the gas hydrates tend to be very unstable. It is becoming increasingly evident that naturally occurring gas hydrates are significant component of the shallow geosphere and are of societal concern in at least three major ways: as an energy resource, a geologic hazard and a major contributor for climatic changes.

Jan 1, 2010

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By M. C. Mound

A recent development using XRD techniques, a unique fixed detector, specifically permitting full mineralogical information simultaneously for the first time, specially designed sample preparation and presentation system and Rietveld codes provide a continuous real- time analysis on the true contained mineral polymorphic composition of powder streams such as ore materials, cement, ground clinker or any other mineral stream conducive to XRD analysis. There are several COSMA systems currently operating in the US, Canada, Italy and Australia, proving service and reliability of this concept. The mineralogical information generated continuously in real time is used for automated efficiency, product quality and reduces costs. Quantitative Phase Analysis information is transmitted to the plant DCS via Modbus over RS422 or ethernet. Some limited information is stored in the on-board computers for optional future use at the operator?s option.

Jan 1, 2010

By V. R. Shea-Albin

This U.S. Bureau of Mines report discusses elastic wave velocity and attenuation behavior as an indicator for changes in load and structural integrity of coal samples. Measuring changes in compressional (P)-wave and shear (S)-wave attenuation and velocity under uniaxial and triaxial compression tests revealed their effectiveness for distinguishing changes in applied load and structural failure of samples. The velocity and attenuation values were used in further calculations such as ratios of P-wave to S-wave values, dynamic elastic constants, normalized velocities, and attenuation coefficients to reveal trends for loading and failure. The behavior of both P-wave and S-wave attenuation and velocity together define distinct and consistent phases of load change and failure for uniaxial and triaxial tests. The S-wave velocity and attenuation illustrate changing axial load and initial development of microfractures within the sample preceding structural failure more clearly than those of the P-wave. The attenuation and velocity ratios and dynamic elastic constants (except the bulk modulus) respond to closure of small preexisting fractures within the coal sample with initial loading to failure of coal samples. The attenuation coefficients and normalized velocities reveal trends similar to those shown by velocity and attenuation.

Jan 1, 2010

Just 104 km (65 miles) from Phoenix, AZ, Rio Tinto hopes its new Resolution Copper Mine will be a showcase for the Rio Tinto management philosophy. Its goal is to have a net positive impact. In every place that Rio Tinto mines, it wants to be able to have an overall beneficial effect on the local community, environment and economy. ?We?re constantly working to understand our impacts, to understand how to minimize our impacts and understand how to mitigate those impacts,? said Resolution Copper Mining chief executive officer David Salisbury, from the global headquarters of Rio Tinto Minerals in Green-wood Village, CO.

Jan 1, 2010

The 28th annual American Mining Hall of Fame Awards Banquet and fundraiser sponsored by the Mining Foundation of the Southwest will be held at the Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 4, 2010. The Mining Foundation of the Southwest is a nonprofit organization whose objectives are public education about the mineral industries, and recognition of outstanding accomplishments in and contributions to the fields of mineral and fuel resources. Funds are being raised to the support the foundation?s educational programs. Among these is the Educational Outreach Program operated jointly by the foundation and the Arizona Department of Mines and Mineral Resources.

Jan 1, 2010

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and tested a system called the Bag and Belt Cleaner Device (B&BCD) to reduce dust levels in and around the bag conveying and stacking process. The device physically cleans either 22.7 kg (50 lb) or 45.4 kg (100 lb) paper bags by using a combination of brushes and air jets. It is completely self-contained and is kept under negative pressure by a baghouse to ensure that dust and product removed from the bags during cleaning does not flow into the work environment and contaminate workers. The bags travel through the device on a chain conveyor, which permits any product or dust cleaned from the bags to fall into a hopper at the bottom of the device and be recycled back into the process via a screw conveyor. Once exiting the B&BCD, the outside of the bags and the conveyor are essentially product and dust free. The B&BCD was evaluated at two mineral processing plants to determine reductions with the device in use. The results of both field evaluations showed that the amount of product removed from the outside of the bags varied from 77 to 93 pet.

Jan 1, 2010