Search Documents

By Roger J. Higgins

Papua New Guinea is a country on the cusp of development, struggling to find a balance between the demands of national and regional growth, landowner expectations and the maintenance of cultural identity. Ok Tedi Mining Limited is the single largest contributor to PNG?s economy, representing about 10 percent of the country?s GDP. OTML is demonstrating that business and country risk can be managed through effective, respectful partnerships with local communities. OTML?s relationships with the communities of PNG?s Western Province are multifaceted. Communities have borne the brunt of the mine?s environmental impact, yet have benefited enormously from the development that the mine has brought. Importantly, the PNG economy is now the ultimate beneficiary of more than four-fifths of the dividends from the mine, the majority of which are held in trust for long-term sustainable development projects. The paper describes how OTML works with the Western Province communities to create a secure operating environment that recognizes the people?s aspirations for development and self-determination.

May 1, 2002

By Tim Grain Joseph

This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sand material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 square yards. Consequences are manifest in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability. The objective of these considerations, as part of the Oil sands Equipment Interaction Program (OsEIP); currently a joint venture between Syncrude Canada Ltd., JPi Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta; is to identify and provide feedback to the manufacturer and end user adverse shovel - ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance.

May 1, 2002

By Theodore M. Katz, W. Stephen Brightwell, David E. LeGrande, Joseph J. Hurrell, Jane A. Lipscomb, Nancy Lessin, Lawrence R. Murphy, Michael J. Colligan, Steven L. Sauter, Richard A. Lippin

Revolutionary changes in the organization of work have far outpaced our knowledge about the implications of these changes for the quality of working life and for safety and health on the job. This gap in knowledge is one of the 21 priority areas for research under the National Occupational Research Agenda (NORA)—a framework crafted by the National Institute for Occupational Safety and Health (NIOSH) and its partners to guide research into the next decade. This report was developed under NORA as the first attempt to develop a comprehensive research agenda for investigating and reducing occupational safety and health risks associated with the changing organization of work. Research and development needs identified in the agenda include (1) improved surveillance mechanisms to better track how the organization of work is changing, (2) accelerated research on safety and health implications of the changing organization of work, (3) increased research focus on organizational interventions to protect safety and health, and (4) steps to formalize and nurture organization of work as a distinctive field in occupational safety and health.

Jan 4, 2002

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

Jan 1, 2002

By K. T. Damodaran

The Chavara and Manavalakurichi placer deposits have been known since a long time for their rich reserves of heavy minerals like ilmenite, rutile, monazite etc. While detailed work has been conducted on the mineralogy and texture of the bulk placer sediments, reports on the detailed investigations on individual minerals are relatively scanty. Though, limited work pertaining to the chemistry of ilmenite has been carried out by Nair et al (1995) and Ramakrishnan et al (1997), a comprehensive study of the weathering patterns of ilmenite along the longitudinal and vertical profiles has not been, so far, undertaken. Data on the microscopic analysis of ilmenite from the southwest placers, too, is sketchy. The present work deals with the variation of the weathering undergone by ilmenite in the southwest placer deposits based on chemical and mineralogical analyses.

Jan 1, 2002

By R. Horn

The financial performance of the mining industry, measured by return on equity and capital employed, has been inadequate for many years. Consequently, mining companies are not valued highly by stock markets. Among the more important causes for the decline in the sector are the conservative working practices and reluctance to adapt to change or to develop new technology, although some relatively recent developments such as SX-EW copper and heap leach gold have made a significant impact on the cost base of these metals. The subsidiary business of metals exploration suffers from the same problems as the rest of the industry. The rate of discovery of ore deposits has been falling over many years and since the late 1990s, there has been a sharp reduction in global exploration activity that, if it continues, will further reduce the global supply of new ore reserves. New technological developments, particularly in geophysics and different operational practices may help reverse this trend. Statistical methods for evaluating the risk of ore reserve estimates will also improve the economic return on new mining ventures. The science of ore geology has potential to reduce exploration risk, but modern ore genetic theory has not contributed greatly to recent discoveries. The junior exploration market has almost ceased, but a new style of technically specialized efficient small exploration company has emerged which, in alliances with major companies, may be the vehicle for future global exploration. Exploration in virgin terrains has a higher risk discounted potential for the discovery of very large orebodies than that in known mining districts but mining companies have little financial incentive for this high risk exploration because of the very long lead time to production. Alliances of two or more companies reduce the risk in both the exploration for and development of major new mining projects. If new orebodies are not found, then metal prices will inevitably rise in the long term. Governments of industrial countries, particularly those with a significant mining industry such as Canada, should therefore provide assistance to exploration in order to maintain their existing industry and prevent a metals shortage from developing in the future with its consequent impact on the world economy and increased environmental damage as large lowgrade orebodies are developed to supply an expanding market.

Jan 1, 2002

By W. E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential."

Jan 1, 2002

Located 350 km west of Sydney and 20 km outside Orange, NSW, lies the Ridgeway Gold Mine û NewcrestÆs flagship Underground Gold Mine. Key to success at Ridgeway has been the fast tracked development of the 3.8 km, 1 in 5.3 conveyor decline which houses the 850 t/hr conveying system feeding the dedicated Ridgeway Concentrator, built adjacent to the existing Cadia Hill Concentrator. Eroc was contracted to develop the steep conveyor decline, drawing on its personnel and experience from past metalliferous, tunnelling and coal mining projects to complete the ambitious schedule within 12 months. This paper deals with the complexities and experiences in safely delivering what is understood to be one of AustraliaÆs steepest declines of any substantial length in a metalliferous mine.

Jan 1, 2002

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By E. Ulrich Klotz

It is difficult to predict accurately the capacity of driven piles in sand. In practice, this uncer­tainty either leads to conservative designs if the capacity is under-predicted, or worse, if the capacity is over-predicted, it can lead to severe foundation problems. One significant possible cause of the problem is that currently available semi-empirical design methods do not capture the fundamental mechanisms that govern the load capacity of driven piles in sands. As part of a recent research project at City University centrifuge tests on a driven model pile in sands have been undertaken. A fully instrumented model pile was constructed and pushed into samples of quartz and carbonate sand thus covering a wide range of mineralogies. Tri-axial tests were used to determine the fundamental patterns of behavior of the sands. This allowed a general framework to be established, in which the in situ stress:volume relationship is shown to govern the capacity of the pile. The paper sets out with a brief introduction of the experimental techniques used in the study. The results of the pile tests are discussed in detail with particular attention given to distribution of the radial stresses along the pile shaft. Existing design methods for piles in sand are then discussed in the light of the new understanding gained from the research, highlighting their deficiencies and suggesting an improved approach.

Jan 1, 2002

By C. Garcia, H. Arias, J. D. Miller, C. L. Lin

The question of ultimate recovery in heap leaching operations is always of particular concern with respect to economic considerations. Of course the particle size distribution is a critical factor which determines ultimate recovery and which must be established based on a balance between the extent of mineral exposure and transport phenomena. Now it seems that the ultimate recovery for a given particle size distribution can be established from mineral exposure analysis by x-ray microtomography (XMT). Using recently developed software, micro-CT data can be used to determine the fraction of mineral exposed and thus the ultimate recovery. Examples of mineral exposure analysis are given for the copper heap leaching operation at Zaldivar, Chile.

Jan 1, 2002

By A. Mezei

A process has been developed to recover cobalt, gold and bismuth from the NICO deposit in Canada. The process consists of a bulk rougher flotation followed by an optional separation by flotation to produce a bismuth concentrate and a cobalt concentrate, grading on average 12.8 % Bi and 1.8% Co, respectively. Cobalt is leached by pressure oxidation at 97% efficiency, producing a pregnant solution suitable for further processing. Before optimization, about 38% of the bismuth is recovered in the selective concentrate, wherefrom it is recovered by ferric chloride leaching followed by cementation, at overall efficiencies exceeding 98%. The gold is recovered from the cobalt and bismuth leach residues by cyanidation, at 95% efficiency. Previous work described the results of the leaching of the concentrates, recovery of gold (Part I) and the recovery of bismuth (Part 11). This work describes the results of the cobalt recovery testwork and the resulting conceptual flowsheet. The sulfur dioxide-oxygen system was the most efficient for the oxidationlprecipitation of iron and arsenic from cobalt bearing pregnant leach solutions, producing purified solutions assaying <1 mg/L As and <8 mg/L Fe. The efficiency of cobalt solvent extraction (from the resulting purified PLS containing about 1 g/L Co) ranged from 9 1 to 98%; the co-extractions ranged from 88 to 100% for copper, from 28 to 33% for magnesium, from 6 to 7% for calcium and from 96 to 98% for zinc. Sulphide precipitation processes (using either sulfur dioxidelelemental sulfur or sodium sulfide) produced residual copper concentrations in the cobalt strip solution ranging from 0.1 to 2 mg/L Cu. About 90% of the calcium and magnesium were separated by scrubbing the organic with cobalt sulfate, producing residual concentrations of 12 mg/L Ca and from 180 to 330 mg/L Mg in typical feed solutions directed to cobalt carbonate precipitation tests. Cobalt carbonate precipitation efficiencies ranged from 75 to 78% when calcium and magnesium co- precipitations were restricted from 8 to 17% and 0.3 to 0.4%, respectively. The limits required by most stringent specifications on commercial grade cobalt carbonate products were met or exceeded.

Jan 1, 2002

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By Serkan Saydam, Ercument Yalcin

This paper presents the results of Caldagi Nickel-Cobalt Ore Deposit&apos;s, located in Turkey, reserve and ultimate pit limit design analysis. Reserve analysis of any deposit requires two steps. First one is to constitute of block model of the deposit and second step is to generate ultimate pit limit. The block model of the Caldagi ore deposit has been created by means of geostatistics. The reserves of nickel and cobalt in this block model are defined as resource, approximately 12 million tons of nickel and 1 million tons of cobalt with average grades of 0.9% Ni and 0.03% Co, respectively. Ultimate pit limit analysis has been performed by considering economic, technical and legal factors. In this paper, the ultimate pit limits are generated by Lerchs & Grossmann (L&G) algorithm. As a consequence of ultimate pit limit design, total amount of tonnage to be excavated is 1.4 billions of tons, 700 million of which contains ore and 747 million of which is the tonnage of waste.

Jan 1, 2002

By J. Matos e Silva

The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the Eurocode 7 recommendations. A comparison is also made with the behaviour of the diaphragm walls during the construction phase. From the referred examples the author presents his conclusions.

Jan 1, 2002

I want to explore whether it is valid or even useful to talk about sustainable corporations. After 20 years of focus on sustainable development, the concept of a sustainable corporation is not particularly helpful and it may in fact be profoundly misleading. Why? û because it obscures the need for corporations to be recognised as part of a sustainable society, rather than achieving some kind of corporate nirvana divorced from the social, political and environmental reality. It is more helpful to ask whether corporations are ready to recognise that they are one player among many within society û with the demands this would place on them in terms of transparency, accountability and social responsibility. The achievement of sustainable development has become the new corporate orthodoxy of many large corporations. It has become a clichT to argue that corporations must become æsustainableÆ. The achievement of æsustainabilityÆ is encouraged, as the ultimate step in some form of corporate evolution. We are failing to recognise that sustainability a process û not an end in itself. An enormous array of instruments is being developed to measure when sustainability is or is not being achieved. For example, corporate reporting has burgeoned into an art form, which describes æsustainabilityÆ in a variety of ways. There is no external standard applied to such reporting. These descriptions are quite partial and often place the best possible gloss on the companyÆs activities. I have become increasingly uneasy about this rhetoric and this paper has allowed me the luxury of sorting out my unease. I will discuss, largely in the Australian context, the current debate and literature and describe the way some global mining corporations are dealing with these questions, and finally, offer some suggestions which might be helpful at the operational level.

Jan 1, 2002

By Brian White

Two examples of en echelon mining-induced fractures seen in hard¬rock mines provided a basis for inferring that fracture zones and bedding plane separations immediately surrounding mine openings are promoted by oblique shear into the openings. It is hypothesized that initial fractures or separations form at the comers of openings as a result of high stress and physical constraint on the rock&apos;s ability to deform elastically toward the opening. These conditions result in a locally preferred direction of shearing. The shearing, in turn, generates tensile stress that initiates a progression of systematically offset fractures approximately parallel to the direction of greatest compressive stress. The fractures or bedding separations create tabular rock layers that amplify shearing displacement through bending and dilation. Such shearing effectively reduces and redistributes the compressive stress, but significant dilation is an inevitable consequence. The combination of dilation and shearing and the progressive development of fracture zones have important implications with respect to ground support. The concept of mining-induced fractures forming as a result of shear is illustrated by two examples from coal mines. First, frac¬tures seen at longwall faces probably result from shear associated with subsidence. The fracture zone that develops approximates or possibly defines the draw angle of subsidence. As the face advances, fractures extend downward along the lower edge of the fracture zone, while upper extensions of the fractures are pressed closed. Fracture zones in entry roofs provide a second practical example. Here, mining-induced fractures typically follow bedding planes. The shear zone model suggests that the first bedding separations develop near the edges of the roof and successive separations progress upward and toward the center. However, if the direction of greatest stress is inclined with respect to the roof, a fracture or bedding separation zone may propagate from one side only and also extend higher. Because coal ahead of the face provides some support against lateral shear deformation, bedding separation is inhibited near the face. Rock bolts installed close to the face ultimately become more strained and bent than bolts installed a few meters from the face, and bolts installed through the more remote part of a separation zone may ultimately experience the greatest tensile and bending strains. This model is supported by field data documenting progressive bolt failures that rapidly propagated downward across the roof during face advance.

Jan 1, 2002

By R. H. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

Jan 1, 2002