Search Documents

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By Rey B. Marquez

This paper introduces and outlines the implementation of Reliability Centered Maintenance (RCM) at Phelps Dodge Hidalgo Inc. By using a disciplined approach to the everyday maintenance functions, a proactive strategy is being developed which "raises the bar" for plant maintenance. The main objectives are: integration of Operations and Maintenance partnerships, transformation of maintenance practices from a reactive to proactive mode through the introduction of a progressive Predictive/Preventive Maintenance program (PDM/PM) paradigm changes, increased management support of maintenance functions, introduction of new indices and root cause analysis, updated; training, and definition of RCM components. RCM is the vehicle being utilized to reach the higher level of equipment availability and utilization. However, the ultimate goal is to venture beyond RCM and into the new frontier of Total Maintenance Management (TMM).

Jan 1, 1998

By P. McGrath

From the mid-1980s through 1997, Echo Bay Alaska evaluated reopening the historic Alaska-Juneau (AJ) gold mine. Their original proposed project underwent numerous modifications in order to minimize the potential for significant environmental impacts. One of the major modifications involved changing .the tailings disposal method from a conventional tailings impoundment to submarine tailings disposal (STD). In 1995, the U.S. EPA began work on a Supplemental Environmental Impact Statement (SEIS) to assess the impacts of the STD proposal. Key features of the STD impact assessment included fate and transport modeling to determine the extent of tailings deposition and the use of ecological risk assessment to predict marine impacts during deposition and ecosystem recovery following STD. A key feature of the SEIS regulatory process included a rulemaking proposed by EPA to exempt the AJ tailings from effluent regulations. Critical to success in moving the project forward was early development of an interactive working relationship with other regulatory agencies and the public.

Jan 1, 1998

By S Logan, J Pu, J Milsom, G McDonald

Management of environmental issues is an integral part of the mine decommissioning process. In Queensland, miners must comply with environmental aspects of the Mineral Resources Act and Contaminated Land legislation. Successful decommissioning involves the integration of a final Plan of Operations, decommissioning report addressing the mineÆs commitments included in its Environmental Management Overview Strategy (EMOS), and Site Contamination Report for relinquishment of leases under the Contaminated Land Act (1991). Niugini MiningÆs Red Dome Mine is proceeding through the decommissioning process. This paper discusses the important environmental management issues including sampling programs, management of culturally significant areas, assessment of background concentrations of target analytes, the use of historical reviews and risk assessment techniques, the timing of works, and the remediation/management of large areas of impacted land. The importance of a clear communications plan between key stakeholders is also discussed.

Jan 1, 1998

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By D. J. Wood

BHP Copper has grown, in just over six years, from a minor participant to the world's largest privately owned copper producer. BHP Copper's major asset is the world's largest copper mine -Escondida in Northern Chile. Ten years ago investing in Chile was considered high risk. Today, Escondida represents an investment of approximately US$2 billion. Reward is the result of managed risk and Escondida is a clear demonstration of both. The Ok Tedi copper and gold mine in Papua New Guinea represents a Rubicon of risk and a retrospective on reward in a developing country on the doorstep of a developed one. The story of these two mines encapsulates risk in the mining industry.

Jan 1, 1998

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and thereby reduces processing costs, recovery losses, and refuse generation levels. In this paper, new approaches for optimal control of the segregation process, using time series models and empirical distributions, are presented and demonstrated using field data.

Jan 1, 1998

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Peter K. Liaw, Niann-i Yu, Wei Zhao

"For a plain-weave Nicalon ™ fiber fabric-reinforced silicon carbide (SiC) ceramic composite, little attentation has been paid to the effect of fabric stacking sequence on its mechanical behavior. In this paper, fiber-fabric stacking sequence effects on the elastic stress distributions, ceramic matrix-cracking stress, effective elastic moduli, and flexural strengths of laminated flexural test bars are quantified. A quantification model is established based on the combination of classical laminated plate theories and a fiber undulation model developed by Chou et al. A FORTRAN program is compiled to implement the modeling, which can be run in a SUN work station. The mechanical performance of a continuous fiber-reinforced ceramic-matrix composite (CFCC) with a [0/30/60] lay-up was analyzed and predicted. The variation in the fiber-fabric stacking sequence can vary the elastic stress distributions along the thickness direction of specimens, magnitude of ceramic matrix-cracking stress, effective elastic moduli of the laminate, and crack initiation sites as well as fracture modes. Moreover, all these factors contribute to scatter in flexural strengths of the CFCC.I. IntroductionWith enhanced fracture toughness and the ability of non-catastrophic (graceful) failure behavior, CFCCs are currently under evaluation for high-temperature structural applications in heat exchangers, combustors, hot-gas filters, boilers components, first walls and high-heat flux surfaces gas turbines, space vehicles and nuclear reactors.[1-8] Extensive applications of CFCCs by industry are still hampered by an insufficient understanding of the mechanical behavior, and sometimes, the lack of a well-developed and widely accepted design philosophy, in addition to the high-production costs."

Jan 1, 1998

By M. Kane, O&apos

BHP Iron Ore initiated research programs in January of 1995 to develop long term plans for decommissioning of the waste rock material at their Mt. Whaleback operation. More than 2 billion tonnes of waste rock were deposited during the past 30 years. Ultimately, the operators will deposit a total of approximately 5 billion tonnes in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semi-arid climate adjacent to Newman, Western Australia, approximately 1200km north-northeast of Perth, Western Australia. The primary research program includes the development of technology for the long term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion, and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. A laboratory program and the soil-atmosphere modelling completed to design the horizontal field test plots are described. The construction of the horizontal surface field test plots are discussed together with the field instruments installed to monitor performance. The key components of the instrumentation program are the design and installation of large scale field lysimeters to measure the unsaturated flow of moisture into the waste rock from the base of the cover layer. The cover system is designed to maximize infiltration during wet periods for subsequent evapo-transpiration while minimizing surface runoff. The result is a near zero net infiltration to the underlying waste material. A key feature of the design is the use of pit run waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long term performance.

Jan 1, 1998

By Kevin L. Gering

A detection method and apparatus have been developed to perform real-time measurement of aqueous free cyanide, C-. A laboratory prototype can measure cyanide ranging from 5 micrograms ,per liter to 100 milligrams per ?liter for analysis times as short as 2 minutes per measurement. Sample size per measurement is typically only a few mI, thus? minimizing the waste volume produced from spent samples. The basis for this detection device is a quantifiable, stable affinity between the electrode material and free cyanide in the sample; The electrode exhibits piezoelectric behavior, allowing it to be used as a microbalance. This technology 'has experienced two generations of laboratory prototypes, and has been thoroughly tested to determine the operational sensitivity toward process variables such as pH, competing reactions, etc. The speed and ,accuracy of this method make it superior to conventional wet chemistry methods used for quantifying cyanide levels in water. A device based on this technology could be useful in areas involving process monitoring and environmental compliance, .particularly in the cyanide-based leach mining industry. Interest for this detector has been shown by the gold mining industry and others. Patent application is in progress.

Jan 1, 1998

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By T. Dunn

FMC Corporation has achieved a significant cost reduction through a new proprietary solution mining and processing technology at its Green River, Wyoming Soda Ash Facility. In the first phase, completed in October 1995, trona ore is dissolved, recovered and processed with the new technology, and then fed into an existing refining plant, replacing dry mined and calcined trona ore. The second phase, completed in April 1996, produced a fmal high purity product and increased capacity by 635,000 t/a (700,000 tpy). Both phases were completed under budget and well ahead of schedule.

Jan 1, 1998

By Yuchun Wang

In principle, supported liquid membranes could be an exceedingly elegant separation process. However they tend to fail by displacement and emulsification of the organic solution in the pores, which allows mixing of the feed and strip solutions. We have stabilized supported liquid membranes comprising moctylamine in nylon and PVDF supports by covering the pores with semi-permeable polyamide films, using an in-situ polymerization technique. Scanning electron microscopy demonstrates that the polyamide films are sensitive to production conditions and the nature of the support. The transport properties of stabilized supported liquid membranes for Cr(VI) are compared with those of unstabilized membranes.

Jan 1, 1998

The Boliden Aitik concentrator in Sweden processes 2,000 tph of low grade copper ore. The plant consists of five grinding lines feeding four bulk flotation banks with a scavenger concentrate regrind mill, and a column cleaner circuit with a regrind mill. The authors installed a model-based expert, optimizing control system to maximize copper recovery in the bulk flotation circuit while maintaining an appropriate copper grade in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent addition rates. It combines the power of a dynamic population balance model which estimates mineral liberation in each stream, an optimizer which computes appropriate set points and a rule-based module which implements the strategy. The benefits have been evaluated over three months. The model-based expert, optimizing control system generates a measurable increase in copper recovery, around 0.5 per cent and an optimized bulk concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 1998

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998