Search Documents

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By AMAN SONI, JONATHAN G. BAGGETT, Nino Ripepi, JUAN J. MONSALVE, Richard Bishop

Underground stone mines are vulnerable to karst void formations due to the erosion of carbonate rocks by groundwater flow. The voids or cavities may lead to hazards including ground collapse and sudden outflow of clay-rock sediments during the development of the mine. This study evaluates the effect of karst voids on the strength of pillars in an underground room-and-pillar limestone mine. Ground-penetrating radar (GPR) surveys were interpreted to map the void boundaries inside a karst-affected pillar. A combination of LiDAR scanning and virtual discontinuity mapping is used to formulate the discrete fracture network (DFN). Discrete element modeling (DEM) helps simulate the effect of karsts and discontinuities in the pillar models with varying stress. It is observed that the cavities may lead to a significant reduction in pillar strength. Apart from posing a hazard to miners and machinery, any advance into these cavities may disrupt mine operations. This research serves as an initial step toward understanding the importance of pillar design in underground stone mines affected by karst voids to prevent local instability or pillar failures.

Sep 1, 2022

By BO HYUN KIM, MARK K. LARSON

The floor-heave and no-floor-heave phenomena at a western U.S. coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria. Although the previous numerical study using FLAC3D very reasonably demonstrated these phenomena, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. As a result, the latter models predicted floor heave that agreed with relative amounts of observed heave from each gateroad system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Sep 1, 2022

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By Rahul Wankhade, Sunil S. Baswankar, Aditya S. Kharatkar

Despite advances in pile design methodologies and piling techniques at site, difficulties and uncertainties still exists for design of piles particularly in coralline deposits and weak carbonate rocks. Such deposits are known to be heterogenous in nature, and occupy major stretches of earth, where piling experiences are probably very scanty. Such deposits are associated with low unit weights and usually consist of weakly cemented calcareous and carbonate soils interbedded with coral rocks containing cavities, which are completely void or filled with coral debris. Many of the studies indicate that conventional parametric relationships are may not apply to such sediments and rock formations. This paper intends to provide an appraisal of the available information that cautions against risks involved in conventional design practice and also serve as a guideline for pile design in such formations despite being a grey area of research. Contents of the paper is expected to provide a basis for the pile design and likely to serve as an eye-opener for research into this important soil-pile structure interaction problem.

Sep 1, 2022

By Viswanadham B. V. S., Babu K. V

Many refineries are in the process of revamping and expanding their existing facilities. Most of the refineries are located in coastal areas due to ease of transportation and storage of crude oil. Considering the criticality of structures as well as prevailing soil conditions, most of the structures are supported on pile foundations. In depth review of sub-surface investigations data followed by liquefaction assessment of the site, it is noticed that site is prone to liquefaction during the seismic event. Among various techniques, driven cast-in-situ piles were selected to mitigate liquefaction. Static cone penetration tests were conducted during the pre and post installation of driven cast-in-situ piles at identified locations. Analysis of cone penetration test data shows that considerable ground improvement has been achieved post-installation of driven cast-in-situ piles.

Sep 1, 2022

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

By Pratik Goel, Sumanta Haldar

High-speed rail is an emerging area of interest in India. The Government of India is implementing prestigious bullet train projects in various parts of the country. High-speed rail (HSR) will be operating in India at about 320 kmph at an elevated track on a viaduct for most of the ongoing and upcoming corridors. High-speed projects in India necessitate an indigenous solution for design applications for viaduct design. Pile groups are extensively used in viaducts for high-speed trains, as they can be a settlement reducer and increase the bearing capacity. Post-construction settlement of pile foundation for high-speed railway viaduct is a concern of engineers. Limited attention has been paid to estimating the post-construction settlement. This paper aims to propose a prediction of the cumulative settlement of pile groups due to cyclic train loading. A three-dimensional finite element model (3D-FEM) of the pile group is established in Abaqus CAE. A suitable plastic model is used to simulate the subsoil. The pile group is modelled as an isotropic-elastic element. The study examines the influence of cyclic loading time and train speed on the settlement of the pile group. The analysis is carried out considering various single pile and pile group parameters like S/D, Ep/Es, L/D, Pile cap thickness, etc. and finally, an optimum configuration is suggested.

Sep 1, 2022

By Arunsiva R., Sivaranan S., Venugopal B., Kumaran M.

Being a rapidly developing country, India is undergoing a massive infrastructure phase change remarkably. The construction industry is already set to boom, but the time and space constraints necessitate the employment of heavy plants and machinery to take the foundations deeper than ever. Operating such machinery on soft or poor ground conditions without a good working platform leads to uncertainties with massive loss of men and machinery. Plenty of such cases can be observed on construction sites across the globe. Unfortunately, forming a temporary working platform is given least to no importance in the construction industry, particularly ground engineering. This glitch can only be addressed through standard guidelines or codal recommendations on designing and implementing temporary working platforms issued by regulatory bodies. The present paper highlights the importance of providing the working platform, existing design method for working platforms such as TWf 2019:02 of Temporary Works forum, Building Research Establishment BR470 and a brief discussion on the design and construction of the geosynthetic reinforced working platform with a case study is also included. A pitch has been made on the importance of Indian codes/guidelines for the design and construction of temporary working platforms. These guidelines will ensure the safety of the men and heavy machinery and, in addition, increase the productivity of foundation construction irrespective of weather conditions and also become part of the regular construction scope.

Sep 1, 2022

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

By Venkatesh S. V J, Shubha M, Srilakshmi G

Choosing for the best option of pile foundations to overcome large lateral and uplift loads for the foundations in transmission line towers/offshore environment is still being a concern to achieve the required capacities but also by considering the suitability aspect in the environment. The objective of this paper is to review the methods that have been done for knowing the uplift resistance and lateral resistance of pedestal piles. Investigations by different methods such as experimental studies, numerical and analytical studies have been done by various researchers in order to evaluate the response of a belled pile. These methods are discussed in this paper and the comparison with straight shaft pile based upon the test and analysis. The results indicated that the uplift resistance and lateral resistance were significantly increased with the adoption of belled piles than straight shaft piles.

Sep 1, 2022

By Madhav, V., M. R., Ahmad, Padmavathi, M. S.

Modulus of deformation (Es), also referred to as elastic modulus is dependent on many variables such as type of loading, degree of anisotropy and non-homogeneity of strata, etc. and is one of the most challenging soil parameters to estimate. Modulus of deformation of soil can be obtained from elemental tests in the laboratory, from in-situ tests or on the basis of correlations with other soil parameters. Back analysis of full-scale loading test is the most appropriate method for the estimation of the deformation modulus since the effects of installation and pile-soil interactions are accounted for. Moduli of deformation of the ground are estimated from different pile load tests, viz., compression, pull-out, and lateral load tests and compared. The method of interpretation of pile load test is based on the initial liner portion of the load-displacement curve. Theoretical solutions of Poulos and Davis (1980) and Madhav and Poorooshasb (1988) that relate settlement or displacement with load based linear elasticity theory are used. It has been established that the modulus of deformation of the ground is not unique but depends on the type of test and the type of loading. The differences can be significant.

Sep 1, 2022

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By Z Gao, D Liao, W Sun, S G. Pooley, J Wang, Z Shi, G Jing, S Ren, Q Chen

Yuanjing processing plant is a scheelite and wolframite plant in southern China. Water shortages and recent environmental regulations mean that the plant must reuse the wastewater that comes from the mining operation. This paper describes the efforts to reuse the mining and ore washing wastewater (MOW) in the processing plant. Initial attempts to reuse the MOW in the strong magnetic separation were unsuccessful because the magnetic media pack was seriously fouled by the micro-fine precipitate generated. The focus changed to reuse the MOW in the scheelite flotation circuit, which includes one roughing, one cleaning and three scavenging steps. Laboratory batch tests showed this would likely be successful because using MOW reliably improved the flotation performance in the laboratory tests. Then a 20 day industrial trial was run in the plant. The trial was very successful with the enrichment ratio of WO3 increasing from 17.4 to 23.6, while the recovery remained around 79.2 per cent. The industrial trial was so successful the company immediately adopted the new scheme, which has remained in use ever since. This technical solution not only alleviated serious water shortages, and satisfied environmental regulations but also improved the plant performance.

Aug 24, 2022

By T P. Tafirenyika, K C. Corin, C T. O’Connor

There is a growing demand for copper driven by its applications in renewable energy and electric vehicles. Sulfide ores are an important source of copper. Flotation is a critical front-end process used to remove gangue minerals and concentrate the copper minerals. The electrochemical activity of sulfide minerals contributes to their overall activity in the flotation pulp. The mineral rest potential dictates how collectors interact with the mineral surface, and hence ultimately on the flotation response. Dissolved oxygen, (DO), pH, redox potential (Eh) and water composition and ionic strength are also significant in controlling flotation performance. The aim of this investigation was to determine the influence of the electrochemical environment both during milling and flotation on the flotation behaviour of bornite and chalcocite. For this investigation, the interactions of collector with bornite and chalcocite were studied using synthetic plant water (SPW1) and deionised water (DIW) at 5 different pH levels. Sodium isobutyl xanthate (SIBX) was used both in microflotation, collector adsorption and zeta potential tests.

Aug 24, 2022

By K Haroon, J D. Speed, S P. Wood

Online analysis of continuous and batch processes has seen a dramatic increase in recent years, with examples ranging from petrochemicals to pharmaceuticals, to industrial biotechnology and food and drink. The particularly challenging environment of alumina processing has meant that instrumentation needs specific features and characteristics to be truly suitable, features such as: robustness, resistance to caustic conditions both in the analyte and the ambient environment, and reliability for long-term continuous use. Here we present the development of a novel FTIR spectrometer that achieves these requirements through the use of a static optics arrangement of mirrors, and stable diamond-tipped light-pipe probe. Firstly we give a very brief explanation of spectroscopic analysis, and the difference between FTIR and other infrared methodologies. Next we outline the novel arrangement of mirrors required to produce an interferogram without moving mirrors, and compare the benefits and drawbacks of this approach instead of conventional designs. We then share the results of laboratory analysis of synthetic Bayer liquors, with detection limits for aluminium hydroxide, sodium hydroxide, sodium carbonate and various sodium salts of organic acids. We then share the results of analysis on production samples, both in idealised laboratory conditions and then online in the process itself. Lastly we present work on in situ ultrasonic descaling solutions to avoid scale build-up and provide continuous cleaning of the probe – preventing the need for probe removal and manual cleaning.

Aug 24, 2022

By M S. Henderson, R D. Alorro, L G. Dyer

An alternative leaching system for rare earth element recovery from monazite is under development. The initial stage utilises oxalic acid to convert the rare earth phosphate into an oxalate salt through dissolution and reprecipitation and it is the efficiency of this stage that governs the overall recovery achieved. It has previously been proposed that lixiviant consumption is the primary limitation in this process. This work further investigates a range of conditions in an attempt to further elucidate the factors influencing the achievable conversion in this stage. It has been shown that the pH may be governed by multiple reactions both consuming and producing acid (thus the mild change over time). The importance of proper mixing and potential to operate at lower temperature with only moderate impact on kinetics has also been demonstrated. Staged/sequential leaching is more effective in fresh solution as opposed to restoring the lixiviant concentration with subsequent reagent addition, suggesting some impact of solution composition. However, contrary to previous findings, subjecting the leach residue to fresh solution resulted in significant decline in leach rate and overall dissolution. This may be because a greater proportion of conversion was achieved in stage 1 in this work than in previous investigation. This may indicate that eventual passivation or the presence of some more refractory REE minerals limits dissolution. Iron dissolution was relatively consistent upon exposure to fresh solution, displaying the ability of the solution to continue to leach the goethite component of the concentrate.

Aug 24, 2022