Search Documents

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By J. J. Webb

At Kerr-McGee&apos;s Galatia Mine in southern Illinois, the need for safe and efficient longwall moves prompted a detailed planning effort. Galatia Mine operates two longwalls on separate coal seams with different geologic conditions. An overview of the longwall move planning as related to manpower training, roof control, ventilation, transportation, equipment recovery and setup will be discussed. The impressive safety record achieved during each of the longwall moves at Galatia Mine verifies that health and safety planning does play a major role.

Jan 1, 1994

By M. J. Friedel

The U.S. Bureau of Mines (USBM) investigated the use of seismic refraction tomography (SRT) for identifying changes in pillar loading at the Foidel Creek coal mine near Steamboat Springs, CO. The inherent three-dimensional problem of directly imaging coal pillar conditions is reduced to a single plane by considering only the load transmitted from the pillar to the adjacent floor rock. Floor strata velocity tomograms (at two pillar locations) illustrate that loading conditions are non-uniform and non-unique. Also, time sequence monitoring, as the longwall face advanced, demonstrated that SRT can be used to image spatial changes in loading conditions. SRT offers the mining engineer a simple and flexible technique for evaluating pillar conditions, and thus, both present and alternative mine designs.

Jan 1, 1994

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

By D. W. Struhsacker

Mineral exploration has evolved into a sophisticated science which uses powerful scientific tools to make mineral discoveries. In addition to their usefulness in performing mineral exploration, these scientific tools can assist the exploration geologist in assessing environmental conditions at exploration sites. During exploration, environmental data acquisition should focus on data collection efforts which can be easily integrated into exploration activities, and should provide information needed for pre-feasibility and preliminary engineering design studies. Environmental studies performed during exploration should also include an environmental liabilities audit and a fatal flaw analysis to assess whether there are any unresolvable environmental or regulatory issues affecting the project. Performing extensive environmental baseline studies during exploration and project evaluation is neither necessary nor recommended. This paper describes opportunities to integrate environmental data collection with mineral exploration activities. This paper also examines how political and communication issues can affect the outcome of permitting efforts, and recommends a strategy to improve the industry&apos;s ability to respond to political challenges and to communicate with the public. This strategy integrates technical and political issues, and implements programs to convince the public of the mining industry&apos;s technological achievements and its commitment to resource stewardship and environmental protection.

Jan 1, 1994

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By R. W. Harnmack

Hydrogen sulfide generated by the anaerobic respiration of sulfate-reducing bacteria was used to treat pH 2.2 water from the abandoned Rio Tinto copper mine in Nevada. The untreated water contained 550 mg/L Fe, 140 mg/L Al, 90 mg/L Cu, 80 mg/L Mn, 60 mg/L Zn, 4 mg/L Co, and 2 mg/L Ni. The bench-scale treatment system examined consisted of a bioreactor for H2S generation and three precipitator/clarifier units for metal sulfide precipitation and recovery. The treatment system reduced the concentrations of all metals except Mn to less than 0.1 mg/L. Manganese concentrations were reduced by 96 percent to 3.3 mg/L. A CUS/SO concentrate (33 pct Cu) and a ZnS/5° concentrate (28 pct Zn) were produced that may be suitable for metal recovery at existing smelters

Jan 1, 1994

By Jae-Ho. Lee

Mercury is a toxic contaminant encountered in the extraction of gold from mercury-containing ores. It is found in the leach solution of CIP circuits and in the cathodes of the electrolyte cells used to electrodeposit the gold. The research conducted has examined the potential for selective removal of mercury from synthetic Au-Hg-CN electrolytes containing only gold, only mercury, and both gold and mercury. Cyclic voltammograms were obtained for mercury- coated copper electrodes with these cyanide electrolytes. Exchange current densities were determined from the voltammograms in the low overpotential region. Laboratory scale batch- electrolysis at constant current was also conducted for the electrolytes containing only mercury and both mercury and gold, at 20 and 50°C and from which the kinetic behavior associated with the process was analyzed. The surface of cathode before and after electrolysis was also characterized and a copper mercury intermetallic (CyHg,) was identified. Gold codeposited with mercury during the later stages of electrolysis. The results of this work corroborate that the mercury-amalgam copper electrode offers a viable electrochemical technique for the selective removal of mercury, however a high-surface-area cathode-cell would have to be utilized to provide for the desired selectivity.

Jan 1, 1994

By F. J. Reichhardt

Abstract -The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterozoic intrusion which is totally covered by sediments of the Karoo and Kalahari Formations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Transvaal Supergroup sediments and lavas. Multiphase deformation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE +Au concentrations.

Jan 1, 1994

By J. Y. Kim, Kenneth Stowe, Stephen Chryssoulis

"A series of flotation tests was carried out on Brunswick Mining ore with various pH modifiers (soda ash, lime, KOH) and added ions (ferric, nitrate, sulphate) in the copper lead rougher circuit. The main objective was to identify downstream effects on sphalerite activation and subsequent zinc rougher flotation. Some significant differences in zinc flotation were obtained. Most notably, soda ash and nitrate ions had a positive impact and ferric ions a pronounced negative effect on selectivity.Selected products from the flotation tests were deslimed at 400 mesh, washed with methanol, air dried, placed in teflon vials purged with nitrogen and stored at -15 degrees C. Numerous liberated sphalerite and pyrite particles were selected under a stereoscope and placed in rows on indium foil. The surface compositions of the particles were analyzed with an innovative laser probe (LIMS). The very small analysis area of the LIMS enables the surfaces of individual grains to be characterized. In addition, the rapid analysis time allows a statistically significant number of grains to be analyzed quickly.Surface lead appears to play a major role in zinc activation/flotation. Possible mechanisms are proposed to explain the variations in metallurgical performance at the different test conditions.IntroductionAlthough the bulk composition of mineral grains is an important consideration for the mineral processor it is ultimately surface composition and topography (edges and dislocations preferred sites for reactions) that control reactivity in flotation and cyanidation (passivation, encapsulation and preg-robbing). Determination of the surface properties of particles from process streams poses a particular challenge for the surface chemist for a variety of reasons, including:"

Jan 1, 1994

By J. J. McClelland

The face area of a continuous mining section of an underground coal mine is the most dangerous area in the mine. Workers there are at nearly twice the risk of death or disabling injury than those in other parts of the mine. Despite extensive training of miners and improved equipment and mining methods, fatality and injury rates have remained constant during the past few years. It is clear that advanced research is necessary to apply new technologies or modify work procedures to solve the continuing problem of the loss of lives and the numerous injuries at the mine face. A U.S. Bureau of Mines research program is developing a Reduced-Exposure Mining System (REMS) that relocates personnel operating the mining machinery at the face away from the hazards to a nearby haven of relative safety. REMS uses proven technologies of computer automation and robotics to help control the operation of the mining machines at the face, while personnel are moved away to a nearby, safe control room. In this protected, well-ventilated environment, they can supervise or control the operation of the machines while viewing what the machine is doing using video and graphic display monitors.

Jan 1, 1994

By P. R. Taylor

Recent research by the investigators has evaluated the oxidation roasting of refractory gold concentrates in the presence of hydrated lime. (Taylor, 1990, 1991, 1992, 1993). These results have indicated that it may be possible to roast concentrates in such a way as to contain nearly all of the sulfur and arsenic in the roaster calcine and that cyanidation may be possible. To further evaluate the behavior of this type of roasting system a laboratory cyclone reactor was built and operated using pyrite and hydrated lime as a .model system. Approximately 50 years ago, the principle of cyclone firing entered practical boiler construction. The appeal of the cyclone configuration was that it afforded the flash combustion process greater efficiency due to turbulence-induced increased mass transfer, heat exchange, and combustion rates.

Jan 1, 1994

By Olusegun J. Ilegbusi

"A two-fluid model is used to calculate flow and heat transfer characteristics of a plasma jet. This model accounts for both gradient-diffusion mixing and unmixing that may result from pressure-gradient-body-force imbalance in the system. The unmixedness is considered to be essentially a Rayleigh-Taylor kind instability. Separate transport equations are solved for the plasma and ambient gas velocities, temperatures and volume fractions. The two fluids allowed to exchange mass, momentum and energy through empirical interaction parameters. The empirical coefficients are first established by comparison of predictions with available experimental data for shear flows. The model is then applied to an Argon plasma jet ejecting into stagnant air. The predicted results show the significant build-up of unmixed air within the plasma gas, even relatively far downstream of the plasma torch. By adjusting the inlet condition, the model adequately reproduces the available experimental data on the temperature profile.IntroductionPlasma jets have important applications in materials processing, some of which include spray deposition, melting and refining, heat treatment and materials synthesis. In a typical reactor, the hot plasma stream entrains a surrounding gas and the resulting heat and mass transfer and the condition of operation of the torch, determines to a large extent, the performance of the unit. The entrainment may prevent uniform mixing and produce regions of unmixed hot/cold gases and non-uniform deposits as a result of insufficient melting of deposit in cold regions. This phenomenon may also affect chemical reaction rate in plasma systems for NOx reduction in exhaust gases.The study of plasma phenomena is often conveniently divided into three parts namely, the plasma torch, the plasma jet and analysis of the particles carried in the jet. The present work concerns processes occuring in the near-field of the plasma jet i.e. just downstream of the torch."

Jan 1, 1994

By Margarete Kalin

Mine abandonment is associated with the securing of access to underground workings, shafts, raises and adits. Waste rock piles and tailings are generally contoured and revegetated. When the waste materials contain pyritic material seepages can often emerge long after the physical reclamation work has been carried out. Their extent and origin has to be delineated to facilitate remedial measures. The depth to which the seepages extended can be determined with an electromagnetic (EM) survey. This paper reports on the experience gained using a winter and a summer EM survey correlated with measurements of specific conductivity at the sediment water interface. Lake sediments and ponds which represent a homogenous background material are good media, where specific conductivity and electromagnetic conductivity can be correlated. The origin of the seepage within the recontoured mine site requires detailed site knowledge, as many anomalies in heterogenous materials such as represented by a mine site are evident.

Jan 1, 1994

By G. L. Peralta

Geothermal energy is an important source of power in more than 12 countries and is a potential source in 50 countries. However, the exploration and use of geothermal resources generate residues such as scale and sludge. The scale is from the steam distribution pipes while the sludge is from cooling ponds. These solids contain significant levels of elements which are of environmental importance notably, arsenic, sulfur, copper, zinc and lead that require safe treatment and disposal. The compositions, phases, textures, morphologies and size of scale and sludge particles have been studied by laser particle size analysis, light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. In addition, their leachability was tested with protocol leaching procedures and sequential extractions. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how the scale and sludge are formed, their leaching behavior if disposed of in a landfill and in developing appropriate treatment strategies.

Jan 1, 1994

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By D. Gove

All mining operations using trucks have a common need to properly match the number and size of hauling units (trucks. wagons. scrapers. etc.) to a loading unit (wheel loader. hydraulic shovel/excavator, cable shovel. push tractor. etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length. grade. or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool which, among other things, can be used to optimize the truck-loader match.

Jan 1, 1994

By B. E. Penrod

The main constituents of flat glass are the eight commonest elements of the earth&apos;s crust. Five of these, silicon, sodium, calcium, magnesium and oxygen are essential. Two more, Aluminum and potassium have beneficial properties. For colorless glasses iron is undesirable, in standard clear glasses a small amount of iron is tolerable, while for most tinted glasses iron is essential. These elements are present in glass as oxides and because they are so common there is no foreseeable resource shortage. The availability of supplies of materials at particular sites at prices which enable a glass manufacturer to be competitive may be another matter. In this paper it is intended to provide a historical perspective to the current situation, to contrast some of the traditional North American and European practices, and to progressively review some of the driving forces for future change and to attempt to assess their effects upon both raw material supplier and consumer.

Jan 1, 1994