Search Documents

By John R. Hoskins

Uniaxial compressive strength of rock is usually determined in the laboratory from cylindrical samples that vary in diameter from 5/8 to 8 inches, using a spherically seated compression head of unspecified size. The Bureau of Mines conducted a series of tests on limestone, marble, sand-stone, granite, and plaster of paris to determine the influence of the spherical head sizes and the specimen diameters themselves on the uniaxial compressive strength. Cylindrical samples of several different diameters of each rock type, all having a length of twice their diameter, were prepared and broken using at least three different diameter spherical heads. Analysis of the data shows that spherical head size does not significantly affect the uniaxial compressive strength of cylindrical rock samples. However, the diameter of the rock specimens does significantly affect the uniaxial compressive strength. Within the range of specimen diameters tested, a coefficient of variation of 6.4 percent for plaster of paris can be attributed to the selection of specimen diameter alone. Similarly, a maximum coefficient of variation of 4.7 percent for the rock types tested can be attributed to the specimen diameter alone.

Jan 1, 1969

By S. Luszcz, R. W. Vook, Fred Witt

In situ X-ray investigations were made on polycrys-talline silver films deposited by vacuum evaporation on (111) CaF2 and (100) NaCl single-crystal substrates at 80°K. The films were evaporated and annealed in an X-ray diffractometer attachment having a residual gas pressure of 2 x lo-' Torr. All measurements were made without exposing the films to the atmosphere. Measurements were made on the films in the as-deposited state and after various annealing treatments. The intrinsic stacking and twin fault densities, the magnitudes of the uniform and nonuniform strains, and the crystallite sizes were determined. In addition the textures in the films were measured qualitatively. The results obtained for the as-deposited films on single-crystal substrates are in substantial agreement with previously reported results for silver films deposited on glass. Intrinsic stacking and twin faults, as well as uniform and nonuniform strains, were present in these films. During the various annealing treatments (up to 350°C) the faults and nonuniform strains annealed out. Considerable grain growth and texture changes occurred also. The effects were much greater for the NaCl substrate than for the CaFz substrate. The relative magnitudes of the grain growth in the variously oriented grains could be explained qualitatively in terms of the thermal strains and strain energies introduced into the differently oriented grains during the initial, irreversible anneal. These strains were due to the different thermal expansion coefficients of the film and substrate. X-RAY diffraction measurements on evaporated films deposited on substrates at low temperature have the advantage that many of the imperfections introduced into the film during deposition are "frozen in". Thus, the influence of a very important experimental variable, substrate temperature, on the imperfection structure of evaporated metal films may be studied. Moreover, the effects of annealing such films makes possible the study of thermally activated recovery processes in these films. The present study was designed to determine the influence of single-crystal substrates on the resultant film structure relative to the previous results obtained using glass substrates.' To this end great care was taken to keep the experimental variables the same in the two cases. Different experimental conditions would, of course, result in films having different physical properties. Again the initial substrate temperature was in the neighborhood of 80°K and the films were subsequently annealed to 350°C. The pure metal silver was chosen for evaporation, primarily because of its relatively low stacking fault energy and consequent high fault density in the as-deposited state. The silver films were formed by evaporation onto air-cleaved {ill} CaF, and (100) NaCl surfaces cooled to 80°K in an X-ray diffractometer attachment2 having a base residual gas pressure of 2 X l0-' Torr. The films were not exposed to the atmosphere until all of the X-ray data had been recorded. In this way one of the most important experimental variables, environment, could be well-controlled and reproduced. X-ray measurements were made at the temperature of deposition and included determinations of the diffraction line peak positions, line shapes, and integrated intensities. The peak position measurements were used to determine the intrinsic stacking fault densities and the average uniform strain in the film. The shapes of the diffraction lines provided information on the twin fault density, true crystallite size, and average nonuniform strain. The preferred orientation in the film was determined qualitatively from the integrated intensities. I) EXPERIMENTAL PROCEDURE The evaporator attachmentZ was charged with 99.999 pct Ag pellets positioned in a tantalum filament which had been outgassed previously at l0-8 Torr. The CaFz and NaCl single crystals were cleaved in air and then placed in position in the chamber so that their cleavage surfaces were on the diffractometer axis. The chamber was prepumped using a sorption pump, sealed off, and then baked at 150°C for 24 hr. The ion pump operated during the bakeout cycle. The substrate was then heated to 500° C by means of an auxiliary heater and kept hot until the rest of the chamber was cooled slowly to room temperature. This bakeout procedure consistently resulted in an ultimate pressure in the low lo-' Torr range. The substrate was then cooled down on 80°K. Its temperature was monitored by a thermocouple wedged into the rear of the copper substrate holder. The diffracted intensity and peak position of the 111, 222, and 333 CaF, lines were measured prior to evaporation. Nickel-filtered, pulse-height-discriminated copper radiation was used. Similar measurements were made for the 200 and 400 lines from NaC1. These measurements were used as a lattice parameter check and to determine the thickness of the evaporated silver films from the attenuation of the substrate lines. The evaporation rates were approximately 3A per sec for both films while the maximum pressures during evaporation were 3 x lo- ' and 7 x 10"8 Torr for the CaF, and NaCl cases, respectively. The film thickness was measured by the attenuation of the CaF, and NaCl substrate lines and by at optical interference method. Values of 1700 and 1500A, respectively, were obtained for the silver

Jan 1, 1969

By Leon Borgman, Michael P. Lipkewich

Orebodies at or near the surface are generally amenable to open pit mining. The development of a mining program involves designing an ultimate pit and a production schedule. This pit maximizes total profit while the production schedule maximize6 the present value of the property. Optimum pit limits can be approximated by two-and three-dimensional numerical techniques. These techniques presuppose that the mineralized area has been sufficiently sampled to allow a reasonably accurate prediction of grade at any spatial location.

Jan 1, 1969

By V. J. Southey

"This paper reviews the history of Wabana Mines from 1892 to 1966, inclusive, in order to clarify the essential factors involved in the achievement of maximum mining efficiency and in the search for an acceptable product to satisfy changing market requirements. It outlines the progressive steps taken to mechanize both surface and underground operations, and forecasts anticipated performance, assuming certain major plans could have been implemented. Results of extensive research in the treatment of the complex ore are discussed. Selected processing alternatives are compared as to feasibility in a summary incorporating estimated capital and operating costs."

Jan 1, 1969

By L. O. Bond

High costs--and high risks--are normal in coal exploration and mine development. But risks and ultimate costs are minimized by foreknowledge of prospective coal seams and adjacent formations. Extensive drill hole programs are often used to obtain needed information. Cores and cuttings from these holes are used to determine coal location, thickness, and quality; they are also used to study physical and geological characteristics of surrounding beds. Valuable as these core and cuttings studies are, their effectiveness is often diminished by loss of recovery or by incomplete analysis. Needed is an effective and economical method for augmenting these studies. Well logs provide information of the type needed for efficient cool prospecting. Furthermore, obtaining these logs in drill holes, and evaluating the data they provide, is both fast and economical. To investigate the usefulness of well logging methods in coal explorations, the authors worked with Mr. Jon Jenkins of Truax Truer Coal Company. Logs were run in a number of drill holes in various areas of the Illinois Basin; these areas provided variety both in coal quality and geologic conditions. The data were studied extensively using computer methods similar to those now used in the evaluation of oil and gas wells. (2, 3) This study was used to produce a computer-generated analysis designed especially for mining problems.

Jan 1, 1969

By J. R. Bell, W. J. Childs, J. H. Bucher, G. A. Wilber

A technique for determining recrystallization times as short as 0.10 sec was developed utilizing the "Gleeble", a commercially available testing system designed for the study of short-time, high-temperaLure themal and mechanical processes. The procedure consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading- to failure. The magnitude of the ultimate load obtained upon reloading decreased with delay lime as recrys-lallization proceeded. The technique was applied to austenite recrystallization in AISI 1010 and AISI 1010 uith 0.02 pct Cb steels. For each steel the reduction in area given the specimen on the first pull was mainlairred at 30 ± 5 pct and recrystallization times deterntined at various temperatures. The results indicaled a significantly slower rate of recrystallization for the columbium-modified composition, suggested the presence of- a recovery stage in the softening process , and indicated a greatly increased softening rate at a temperatuve where significant allotropic transformation to a partially ferritic Structure could occur. In recent years increasing attention has been paid to the fact that the process of recrystallization of austenite deformed at elevated temperatures is far from instantaneous at many practical hot-working temperatures.1-3 This realization has given rise to such terms as hot cold-working1 or warm-working,2 These terms generally describe processes where the recrystallization rate at the temperature of deformation is slow enough to have an appreciable effect on mechanical properties despite a relatively high deformation ternperature. The mechanical properties of interest can be either the properties at the deformation temperature as in hot-workability studies4 or the room-temperature properties after cooling as in the many recent studies of various thermomechanical processes172 where heat treatment and deformation are intentionally combined to give a unique set of room-temperature properties. Because of this interest in processes where the austenite recrystallization kinetics can be an important variable, the development of quantitative methods of following the course of short-time, high-temperature recrystallization has received increasing attention.l,3,5 The experimental methods to date have, in general, relied upon rapidly deforming the austenite, holding at temperature for various brief intervals, quenching as G.A.WILBER and W. J. CHILDS, Members AIME,are Research-Fellow and Professor, respectively, Rensselaer Polytechnic Institute, Troy, N. Y. J. R. BELL and J. H. BUCHER, Member AIME, are Research Engineer and Research Supervisor, respectively, Graham Research Laboratory, Jones & Laughlin Steel Co., Pittsburgh, Pa. Manuscript submitted March 13, 1968. IMD. rapidly as possible, and then using room-temperature measurements to follow the recrystallization process. Although such methods can be successfully applied to certain alloy steels, the existence of the allotropic transformation during cooling of plain-carbon or low-alloy steels tends to obscure the results. Thus, such room-temperature measurements as hardness and X-ray line widths do not correlate well with the extent of austenite recrystallization before quenching,5 and results based on room-temperature microstruc-tural observations are dependent upon the success in correlating the observed structure with the prior aus-tenitic grain structure.1,3,5 The purpose of the present work was to develop a quantitative method for the determination of short-time, high-temperature recrystallization rates, based on measurements made at the temperature of deformation. EXPERIMENTAL TECHNIQUE The basic technique consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading to failure. The data were obtained in the form of traces of load and elongation as a function of time. Due to the high deformation temperature, the strain hardening introduced during initial loading was progressively annealed out with holding time after unloading and the loads obtained upon reloading decreased as this softening proceeded. Although the value of the second load at any Consistent point On the load-elongation curve could have been used as a measure of the degree of softening, the most convenient to use was the ultimate load. The softening indicated by the decrease in the second ultimate load with time is essentially a process of annealing of cold-worked material at a high deformation temperature. Although some recovery grain growth may contribute to such a softening process, it is generally considered that the major softening which must take place to achieve complete removal of substantial Strain hardening will occur by the formation of new, stress-free grains. As the results of this work indicate that essentially complete removal of strain hardening did in fact occur. the primary softening process will be attributed to recrystallization, and specific reference made where it appears that other mechanisms may be contributing to the total observed softening. It would, of course, be of interest to attempt to correlate the results of this work with the actual austenite fraction recrystallized as determined by other techniques. This was not attempted in the present work because it would have required running a large number of additional specimens and, as discussed previously, there is limited assurance that the results would accurately reflect the prior austenite fraction recrys-

Jan 1, 1969

By R. E. Reed-Hill, W. H. Hartt

High-purity magnesium single crystals, oriented with basal plane parallel to stress axis, were deformed in tension at room temperature so as to form second-order (1011)- (1012) twins. Investigation by optical and replica electron microscopy revealed that these twins can support very large internal strains approaching 1000 pct and that fracture follows as a direct consequence of these strains. At low strains the basal plane within (10i1)- (10i2) twins rotates with increasing deformation until it becomes approximately parallel to the twin boundaries. This rotation is not consistent with deformation by basal slip in the double twin, but may be rationalized in terms of nonbasal slip. Observations also indicate that basal slip in the primary (1011) twin, prior to second-order twinning, may contribute to this rotation. Deformation markings that are difficult to interpret in terms of slip on previously observed systems were noted in the twin bands. A possible means of rationalizing these markings is to relate them to grain boundary shear. The fracture associated with these twins is thought to initiate by formation of voids at the twin boundaries. These grow into microcracks, with ultimate fracture occurring by tearing of the interconnecting regions. THE significance of deformation and fracture along second-order (10i1)-(10i2) twins in polycrystalline magnesium1-' and many magnesium alloys4 was discussed in a previous paper.5 It was noted that this double twinning mode effectively controls the room-temperature deformation and fracture of magnesium single crystals, oriented with the basal plane parallel to the tensile axis. Reed-Hill and Robertson6 observed that, although these crystals may fracture at a macroscopic strain of less than 1 pct, shear strains up to 1000 pct could occur within (1011)- (10i2) twin bands. They concluded that the fracture was "ductile" and resulted from concentrating the deformation into a very small volume. The present research was undertaken to obtain a better understanding of the deformation and fracture associated with these twins. EXPERIMENTAL TECHNIQUES The experimental procedure involved straining high-purity magnesium single crystals in tension at room temperature. Specimens were oriented so that the applied stress direction was within 2 deg of the [1010] crystal axis. The specimen cross section was rectangular with faces closely parallel to (1210) and (0002). The specimen preparation and testing procedures have been described in detail elsewhere.5 Second-order (1011)- (1072) twins nucleated during straining were studied using optical and replica electron microscopy techniques. For the latter, cellulose acetate-carbon double replicas were employed. Observations were made on the (1210) crystal surface, which is the plane of shear for twins of this type. In addition to the single crystals, some investigations were carried out on longitudinal polycrystalline specimens. These were obtained from high-purity magnesium plate with a texture in which the basal planes of the grains tended to be nearly parallel to the specimen axis. All. polycrystalline specimens were annealed prior to testing in order to produce a coarse grain structure, permitting Laue back-reflection X-ray photographs to be obtained from grains of interest. EXPERIMENTAL RESULTS a) Deformation Within ( 101 l )-( 1072) Twins. Fig. 1 is an optical micrograph demonstrating the extent of the plastic deformation that can occur in (1011)-(10i2) twin bands. Notice at the lower left corner of the photograph the large displacement of the dark band (a polishing step) where it crosses the twins. The shear strain in the twin band at this position was computed to be 700 pct, using the ratio of step width to twin thickness. It was previously shown5 that (1011)- (1012) twin bands are often composed of small, separate twins aligned close to the macroscopic habit plane. Fig. 2 is an electron micrograph from near the upper end of the twin band in Fig. 1. This illustrates that the twin habit often does not coincide exactly with the macroscopic band habit, but may be inclined at a slightly smaller angle to the matrix basal plane. Figs. 3 through 6 are electron micrographs of the twin band in Fig. 2 illustrating successive steps in the development of deformation inside the band. A twin band such

Jan 1, 1969

By C. van Dijk

In Sept., 1960, a steam-drive project was started in the solution-gas drive area of the Schoonebeek field. A part(ern of three five-spots and one four-spot was selected covering an area of 65 acres. The pay in the project area has good lateral continuity and dips slightly to the northeut; it is about SO ft thick and permeability increases from 1,000 and at the bottom to approximately 10,000 md at the top. The oil originally in place was 12.6 X 10' bbl. The oil has an in situ viscosity of about 180 cp. At the start of the steam drive the cumulative primary production due to. solution-ga.7 drive amounted id 4 Percent of the oil originally in place. Reservoir pressure had dropped about 120 psi and no significant primary re-.serves remained. Some 11.3 million bbl of steam (all steam quantities are expressed in barrels of water vaporized) have been injected, resulting in production of an additional 4.1 X I0 9bl of oil, or 33 percent of the oil originally in place. This corresponds to a cumulative oil-stearn rario of 0.37 bbllbbl. It appears that the steam preferentially moves r updip while liquids are produced mainly from downdip wells observations indicate that tile steam flows through only the upper part of the formation. The lateral steam distribution in the pattern is satisfacrory since several prodriction wells hardly reacted and, hence, cori tributcd little to the oil production. Production performance and results from material balance calcutlations agree satisfactorily with the results of large-,scale laboratory experiments. On the basis of these experirmental results the .steam drive, together with a cold water follow-up. is expected to bring ultimate recovery to a value of crt leas: 50 percent of the oil originally in place. No serious production problems have been encountered. However, due to mechanical fuilure, two old prodriction wells and one injection well had to be replaced. An extension of the. steam drive in this area is under connstruction. Introduction The Schoonebeek oil field, discovered in 1943 and developed after World War 11, is situated in the eastern part of the Netherlands. The main oil reservoir in this field is the Valanginian sand. A completely sealing fault divides this reservoir into two areas (Fig. 1): the southwestern part of the sand body where primary production is ob- tained by means of a solution-gas drive, and the remain. der where edge-water drive is the production mechanism. In the greater part of the field the reservoir consists of a single, unconsolidated sand body. The net thickness ranges from 30 to 100 ft and the top is between 2,400 and 2,800 ft below sea level. Formation permeability varies from approximately 10,000 md at the top to values of the order of 1,000 md at the bottom, and porosity is about 30 percent. The reservoir contains a paraffinic oil of 25" API gravity with an in situ viscosity of 160 to 180 cp. Initial oil saturation was high (85 to 90 percent). The relatively large quantity of oil in place (more than 10' bbl), and the low ultimate primary recoveries expected from this field — approximately 15 percent stock-tank oil initially in place (STOIIP) for the water-drive area and 5 percent STOIIP for the solution-gas drive area — clearly indicate ample scope for secondary recovery. Because ies-ervoir and crude characteristics made this field suitable for thermal secondary recovery, a hot-water drive project was started in the water-drive area about 10 years ago. A few years later a steam drive and an in situ combustion project were started in the solution-gas drive area. This paper deals with the performance of the steam-drive project, which was started in Sept., 1960, and which is still in operation. Design of Steam-Drive Project, An experimental investigation of the steam-drive process carried out by schenk in 19561 indicated that under schoonebeek conditions steam injection could be an attractive secondary recovery method. the findings and encouraging results of a pilot test in the Mene Grande field in venezuela,i led to the design of a steam-drive project in the schoonebeek field, Pruject Site and Pattern In 1958 the reservoir pressure in the solution-gas drive area had decreased to about 120 psi, and oil production rates of wells in this area had dropped to 7 to 10 B/D. The cumulative primary production was about 4 percent STOIIP, leaving an oil saturation of approximately 85 percent. In view of the large amount of oil left behind in the reservoir, the solution-gas drive area was selected for the planned steam-drive project. The area in the vicinity of Well S1 3 (Fig. 2) was considered to be suitable since it is at least partly isolated from the rest of the field by faults and the sand is relatively thick (about 80 ft).

Jan 1, 1969

By C. T. Liu, J. Gurland

The deformation behavior in tension of spheroidized carbon steels was studied at room temperature as a function of carbon content, 0.065 to 1.46 wt Pct, and carbide particle size, 0.88 to 2.77 p. It was found that the Hall-Petch strength-grain size relation is directly applicable to the yield and flow stresses of the two lower-carbon steels , 0.065 and 0.30 pct C. The strength data for the medium- and high-carbon steels, 0.55 to 1.46 pct C, also satisfied the Hall-Petch relation, provided that these data are based upon the particle spacing. Beyond 4 pct strain, the flow stress data of all the steels studied could be represented by the same Hall-Petch relation with dinerent spacings for grain boundary and particle strengthening. The behavior of the higher-carbon steels was consistent with the postulated formation of a dislocation cell network during processing and initial deformation (up to 4 pct strain). The cell size was assumed to be equal to the planar particle spacing. The true stress at the ultimate tensile strength was also found to be a function of the particle spacing. At a given temperature and strain rate, the yield and flow stresses of carbon steels depend on the type and dimensions of the microstructure. Starting with the work of Gensamer et al. in 1942,' experimental studies on pearlitic and spheroidized carbon steels revealed that the strength of steels is a function of two main parameters: the ferrite grain size2'3 and the carbide particle spacing;1'4'5 on this basis, two different strengthening mechanisms have been developed to apply to steels of low and high carbon contents, respectively. In polycrystalline iron and mild steels the grain boundaries are regarded as the major structural barriers to slip. The relation between strength and grain size is generally represented by the Hall-Petch equation which is based on a linear proportionality between strength and the inverse square root of the average grain size.2'3y677 However, Gensamer et al.' and Roberts et related the yield strength of medium -and high-carbon steels to the carbide particle spacing alone, and they found a linear relation between the logarithm of the mean free path in the ferrite and the yield strength in both spheroidized and pearlitic steels. By means of the electron microscope, Turkalo and LOW' extended the study to finer structures; they concluded that the logarithmic relation is not valid for the entire range of microstructures unless grain boundaries are also included in the measurement of the mean free path. For the specific case of spheroidized steels, Ansell and aenel' found that the yield strength data,4'5 when plotted as a function of mean free path, fit the Hall-Petch equation; however, T'ysong found that the same data fit the 0rowanl0 relation if a planar inter-particle spacing is used. Recently Kossowsky and ~rown" studied the strength of prestrained spheroidized steels, 0.48 and 0.95 pct C, and concluded that the strength due to the carbide dispersions varies linearly with the reciprocal of the square root of the mean free path between carbide particles and dislocation networks. Such networks were first observed by Turkalo." The conclusion common to all these studies is that the available slip distance in the ferrite is the most important variable in determining strendh. Previous work on carbon steels is restricted to limited composition and strain ranges. The mechanism which governs the flow properties is not clearly understood, and, in particular, little is known about the composition dependence of the transition between grain boundary strengthening and particle hardening. The purpose of the present work is to investigate the strengthening mechanism in spheroidized steels over a wide range of carbon content, 0.065 to 1.46 wt pct, and plastic strain, yielding to necking. The spheroidized structure was chosen because of its relative simplicity and the relative ease of control and measurement of the structural parameters. The experimental work is limited to tensile testing at room temperature at constant extension rate. The effects of the carbide particles on the fracture behavior of spheroidized steels are discussed elsewhere.13 EXPERIMENTAL PROCEDURE Eight different grades of vacuum-cast carbon steels were supplied in the form of forged and rolled plate by the Applied Research Laboratory of the U.S. Steel Corp. The compositions furnished with these steels are given in Table I; the carbon content ranges from 0.065 to 1.46 wt pct, or from 1.0 to 22.3 vol pct of carbide. The steel plates were cut transversely into rods a little larger than the test specimens, 1 in. gage length, i in. diam. The rods were austenitized in air (enriched with CO by a consumable carbon-rich muffle) at 50° C above theA, orA., temperature for 2 hr and then quenched in oil with vigorous stirring. The as-quenched rods were tempered in two stages in order to obtain the desired distributions and sizes of carbide particles. The rods were first tempered at 460° C for 10 hr and then at 700" C for periods ranging from 4 hr to 3 days, in vacuum. After final machining, all specimens were vacuum-annealed again at 650°C for 1 hr in order to relieve residual stresses. The tension tests were carried out in two steps. The initial part of the load-strain curve, up to about 2 pct strain, was determined on a Riehle testing machine with an extensometer of small strain range, 4 pct strain, in order to obtain the yield and initial flow piopertiesi As soon as the first part of the test was finished, the specimen was placed in an Instron testing machine equipped with a strain gage extensometer with a maximum strain range of 50 pct. The load-strain curve to fracture was

Jan 1, 1969

By R. K. Dann, L. W. Roberts, R. B. Benson

The mechanical properties of 300-series stainless steels were investigated in both high-pressure hydrogen and helium environments at ambient temperatures. An auslenitic steel which is unstable with respect to formation of strain-induced a (bee) and € (hcp) mar-tensile is embrittled when plastically strained in a hydrogen environment. A stable austenitic steel is not embriltled when tested under the same conditions. The presence of hydrogen causes embrittlement at the mar-lensitic structure and a definite change in the general fracture mode from a ductile to a quasicleavage type. The embrittled martensitic facets are surrounded by a more ductile type fracture which suggests that the presence of hydrogen initiates microcracks at the martensitic structure. If a steel is unstable with respecl to fortnation of strain induced martensile, plastic deformation in a hydrogen environment will produce rapid embrittlement of a notched specimen in comparison to an unnotched one. FERRITIC and martensitic steels can be embrittled by hydrogen that has been introduced into the alloys, either by thermal or cathodic charging prior to testing.1-5 However, conflicting reports exist as to whether austenitic steels that are stable or unstable with respect to formation of strain-induced martensite can be embrittled by hydrogen.8-12 A recent investigation has shown that cathodically-charged thin foils of a stable austenitic steel can be embrittled.13 An earlier investigation of a thermally charged 18-10 stainless steel revealed a significant decrease in the ductility only at the lowest test temperature of -78°C, although strain-induced bee martensite was shown to be present in one specimen tested at ambient temperatures.' When martensitic steels are tested in a hydrogen atmosphere, they are embrittled.'4-'7 It has been observed in this Laboratory that 304L steel, which is unstable with respect to formation of strain induced martensite, forms surface cracks when plastically strained in a high-pressure hydrogen environment. Work in progress elsewhere concurrent with this investigation has also established that 304L is embrittled when tested in a high-pressure hydrogen atmosphere." The objective of this investigation was to study the effect of a high-pressure hydrogen environment on the tensile properties of a stainless steel that contained strain-induced martensite (304L) and one that did not (310). EXPERIMENTAL TECHNIQUES Notched and unnotched cylindrical specimens were machined from 304L* and 310 rods that were heat- treated at 1000°C in argon for 1 hr followed by a water quench. The chemical analyses of these steels are given in Table I. The unnotched specimens had a reduced section diameter of 0.184 & 0.001 in., a gage length of 0.7 in., and were threaded with a 0.5-in.-diam. thread on each end. The notched specimens had a reduced section diameter of 0.260 * 0.001 in. and a 0.75-in. gage length, with a 30 pct 60 deg v-notch at the center. The notch had a maximum root radius of 0.002 in. The tensile bars were fractured in a hydrogen or helium atmosphere of 104 psi at ambient temperatures. The system used for mechanically testing the specimens is to be described in detail elsewhere.19 Several specimens of each type were tested in air using an Instron testing machine. The same yield strength and ultimate tensile strength were obtained in 104 psi helium with the above system as with the conventional testing machine. Magnetic analysis was employed to determine that there was a (bee) martensite in plastically deformed 304L and that it was not present in plastically deformed 310. The magnetic technique depended on allowing the material being studied to serve as the core between a primary and secondary coil. Thus, any change in the amount of magnetic material present between the annealed and plastically deformed steels will be indicated by corresponding changes in the induced voltage in the secondary circuit." The ratio of the output signal of a nonmagnetic stainless steel to a completely magnetic maraging steel was 2000 to I. Several unnotched 304L bars tested in hydrogen were analyzed for hydrogen by vacuum fusion analysis. There was an increase in the hydrogen content to approximately 2 ppm for the specimens tested in hydrogen, as compared to less than 1 ppm for the as-received material. Several thin sections cut from notched areas of 304L specimens tested in hydrogen and containing the fracture surface contained approximately 1.5 ppm H. The accuracy of these determinations was estimated to be ± 50 pct.

Jan 1, 1969

By Northcutt Ely

My topic today is our Nation's interest in the minerals beneath the oceans. I will state what I think should be our objectives, the means available to attain these objectives, and the obstacles to their accomplishment. It is possible that as early as this year of 1969 our country must make policy decisions on this subject, and that these, once made, will be almost irreversible. Two factors are hastening an. early decision. First, the 1958 Convention on the Continental Shelf becomes eligible for amendment after June 10, 1969, if the Assembly of the United Nations so decides. Second, the United Nations has created a permanent committee of 42 nations, which was preceded by an ad hoc committee of 35 nations, to study the question of the peaceful uses of the seabed "beyond the limits of national jurisdiction. While these measures purport to deal with the creation of a regime to govern mineral development on the deep sea floor beyond the limits of the jurisdiction of the coastal nations, it has become clear that the urgent issue is the extent to which this future regime shall acquire jurisdiction over the mineral resources of the continental margin, and receive royalties therefrom. This brings the proposal into potential collision with the interests of the coastal nations under the 1958 Convention on the Continental Shelf, including, of course, the United States.

Jan 1, 1969

By Douglas A. Elkins

The unique characteristics of plasmas, their current applications, and ongoing research into new applications are described. Major technical and economic problems in application of plasma technology are discussed. Examples of potential applications of plasma in extractive metallurgy are described and evaluated. The report includes a selected bibliography of articles on plasma and related high-temperature technology.

Jan 1, 1969

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By B. H. Caudle, L. G. Davies, I. H. Silberberg

This paper presents a method of predicting the recovery and performance of a five-spot steam injection project, in which a realistic approach to pattern sweepout efficiencies is made. Published methods for radial systems were modified for the five-spot pattern by approximating the stream lines with straight lines radiating from the injection well and then converging to the producing well. In each radial segment, the position of the steam front and the temperature profile ahead of the steam front were determined by heat balance equations, which included an estimation of heat losses to surrounding formations. The location of the saturations behind the cold water front was determined from a Buckley-Leverett solution to the material balance equation. Results from this program show steamflood recovery in a five-spot pattern to be considerably less than that predicted for true linear or radial flow systems. For a specific reservoir containing 900-cp oil, a steamflood in a purely radial flow system was predicted to recover more than 75 percent of the original oil in place when 2 PV of water had been injected as steam. A five-spot steamflood with otherwise identical properties was predicted to recover 10 percent of the original oil in place when 0.15 PV of water had been injected as steam and to recover almost no oil thereafter. A cold water five-spot flood in this system was predicted to recover approximately W percent of the oil in place with I PV of water injected. For a five-spot pattern in an example reservoir with 10-cp oil, steam injection similarly showed lower ultimate recovery than water injection but no improvement in recovery rule. Introduction The thermal recovery method considered in this study is steam injection in a five-spot pattern. Pattern steam injection has been given little attention in the past, possibly because of some rather obvious disadvantages. Unless steam temperature is maintained throughout the entire swept area, the process will revert to simple waterflood with all heat being lost prior to reaching the oil bank. Also, the oil viscosity reduction takes place near the steam front and not around the producing wellbore, so that low producing rates must still be endured. This is the reason for the success of the steam stimulation, or cyclic injection, in which the fluids are produced from the same well used for injection. On the other hand, steamflooding can offer some advantages. Oil displacement is by four methods: (1) mechanical displacement by the condensed water, (2) viscosity reduction of the crude oil, (3) swelling of the crude oil, and (4) distillation of the crude oil in the steam zone. Although dependent upon the crude, laboratory experiments have shown displacements up to 80 percent by steamflooding. In addition, steam is a good heat transport medium, since it is cheap and has a high heat content. Previous Investigations Previous publications have reported methods for predicting recovery in a steamflood for linear and radial systems. Since no pattern sweep efficiency is taken into consideration, the recovery even from a radial system must be greater than from more realistic geometries such as the very common five-spot patterns. Probably the broadest coverage is given by Willman who reported experimental results and offered a method of predicting recovery for a radial flow system. They concluded that both hot water and steam injection recover more oil than an ordinary waterflood, and that steam injection could yield recoveries "as much as 100 percent greater than by water flood." They also concluded that both the heat requirements for a reservoir and the residual oil remaining in the reservoir after steam injection were independent of the amount of oil originally in place, that short exploitation times were desirable, and that a high percentage of net sand in the reservoir with a high initial oil saturation was desirable. The method assumes that the flood occurs in three concentric cylindrical zones: (1) an inner steam zone, (2) a central hot water zone, and (3) an outer cold waterflood zone. Displacement in the steam zone is based on laboratory-determined residual oil saturations while the hot water and cold water zones use the conventional Buckley-Leverett equations. Although the results shown by Willman et al. are for a radial system flowing out from the well to an assumed external circular boundary, their equations did

Jan 1, 1969

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

By Karl C. Dean

The Bureau of Mines stabilized 10 acres of windblown copper mill tailings at McGill, Nev., by a combination chemical-vegetative procedure. Legumes, winter wheat, wheat-grasses, and wild rye were seeded, and the area was subsequently sprayed with a resinous adhesive chemical to stabilize the sands until the vegetation could grow. During the year since treatment, the area has been well stabilized against wind erosion. The established vegetation appears to be capable of self-perpetuation and renewal without irrigation. The cost of stabilizing the area was $135.50 per acre.

Jan 1, 1969

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruction3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1969

By B. H. Caudle, B. M. Hickman, I. H. Silberberg

Secondary recovery projects often are not started in oil reservoirs until dictated by rising GOR's or declining oil production. Such circumstances require a well dispersed injection pattern to prevent the oil bank from bypassing the production wells. Many times this purpose is served by using the five-spot or line-drive patterns, in which half of the wells are made injection wells. A regular injection pattern is proposed that is based on the same well spacing as the five-spot but in which only a third of the wells need be converted to injection wells. Fluid flow model studies on this proposed pattern show that production histories will be as good as those for a five-spot pattern at mobility ratios of three and above. The model data are presented in a form that may be used to predict recoveries from both homogeneous and stratified formations. Introduction The injection of fluid into a petroleum reservoir usually is prompted by an actual, or predicted, loss in the productivity of the reservoir. Often, an oil reservoir is produced by pressure depletion until high GOR's dictate a change in policy. Fluid injection also causes increased ultimate recovery, but this usually is of less importance to the operator than is the maintenance of the production rate. It is a fact that the ultimate recovery in any particular fluid injection project is relatively independent of the number and spacing of the injection wells as long as the reservoir voidage through the production wells is balanced by the total injection rate. However, the response of a production well is directly affected by the distance it lies from an injection well. In places where the well productivities are declining, the injection wells should be spaced as evenly as possible among the producing wells ("dispersed" injection pattern). More particularly, if the production response depends upon the formation (and subsequent production) of an oil bank, each production well should be surrounded by injection wells. Otherwise, the oil productivity will increase very little as the oil bank moves past the well.'.' An evenly spaced injection pattern has the best chance of generating an oil kick in the production wells. If reservoir voidage and injection rates are to be equal, the ratio of injection wells to production wells must be equal to the ratio of the average injectivity to the average productivity (in reservoir volumes). This ratio is in strumental in choosing the injection pattern. Table 1 shows the production well to injection well ratio for the dispersed injection patterns that have been described in the literature.'-' All of these patterns will have comparable recoveries and response times (for the same basic distance between wells). The choice of pattern there fore depends upon the relative injectivity and productivity of the wells and upon the type of drilling pattern employed. Another important factor may be the ability of the proposed production wells to make up the lost productivity from those wells converted to injectors. These factors become more pronounced at the higher oil viscosities (low gravity oils). All other things being equal, the probable ratio of single well injectivity to single well productivity will be equal to the water-oil mobility ratio of the proposed flood. Thus, high mobility ratios (due to low gravity oil) should call for fewer injection wells — as long as these injection wells are "dispersed" to obtain more even pro duction response for the remaining wells. Secondary re covery projects in oil reservoirs seldom, if ever, will have mobility ratios requiring more injection wells than production wells. Thus, only the last five of the patterns listed in Table 1 will be of significant interest in oil recovery. Almost every development drilling program calls for the wells to be drilled along equally spaced rows and

Jan 1, 1969