Search Documents

By Herbert A. Wendel

Reaching the miner with safety education" is R the ultimate goal, the main objective, of every safety program in the mining industry. If we can get safety education to every worker, and it is properly learned, enforced and obeyed, we should eliminate at least 85% of all potential accidents. We should then have very few accidents as a result of unsafe behavior, which, in turn, would allow us to concentrate most of our future efforts on preventing the types of accidents which are caused by faulty or defective machinery, equipment, tools and materials. An uninformed or uninitiated person would think that it should be a rather simple process to reach the miner with a safety education. Theoretically he would be right because here we get involved in a matter of semantics. When we say "reaching the miner with safety education" we actually mean that this education must also be accepted and learned by the miner; we intend to mean that safety must be observed and followed at all times. But in order to realize our complete meaning of the phrase, we must find the solution for a number of problems and obstacles which are well known to management and safety personnel.

Jan 1, 1965

By James A. Roberson

THE mechanical behavior of molybdenum has become a matter of considerable interest in recent years because it has a reasonably high strength at high temperatures. Various aspects of its fatigue behavior have been investigated previously,1-3 and the results can be summarized as follows. Recrys-tallized molybdenum exhibits a fatigue limit which decreases continuously with increasing temperature. The ratio of fatigue-limit stress to ultimate tensile stress is high (0.6 to 0.8) and reasonably constant. The present work was undertaken to determine the effect of variations in environment on the fatigue of molybdenum stressed in fully reversed axial tension compression. In order to provide a basis to which these data could be compared, a complementary series of fatigue tests were made in vacuum. All of the specimens used were made from one mill lot of unalloyed molybdenum which had been vacuum-arc melted, worked down to 1-in.-diam bar, re-crystallized, then warm-worked to 5/8 in. diam. The interstitial content by weight was as follows: C—0.022 pet, 02-0.0026 pet, Hz-0.0001 pet, and N20.0002 pct. The average grain diameter in the transverse direction was about 0.035 mm, and the average grain length was about 0.15 mm. Typical tensile-test data are shown in Table I. None of the specimens tested exhibited an upper yield point.

Jan 1, 1965

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two- thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By D. R. Mathews

Electrorefined vanadium was evaluated with respect to tensile properties and the effects of interstitial contaminants in the temperature range of 77° to 273° K. The yield strength of 18,500 psi and hardness of 63 diamond pyra-mid hardness (DPH) of electrorefined vanadium are approximately equal to that of iodide crystal bar vanadium. The ductile-brittle transition temperature was found to be below 77° K, but with 0.175 weight-percent oxygen or 0.10 weight-percent nitrogen, it increased to between 123° and 190° K. With carbon content up to 0.11 weight-percent, the transition temperature remained below 77° K. The yield strength of the interstitial-containing alloys can be expressed by: au = 7.5 + 480 (pct N) + 290 (pct 0) + 280 (pct C), where au is the upper yield stress in 1,000 psi at 273° K. Profuse deformation twinning occurred in the alloys tested at 77° K. However, twinning could be suppressed by dissolved oxygen or nitrogen in excess of 0.15 and 0.086 weight-percent, respectively. Carbon, even though present in excess of the solubility limit, did not affect twinning.

Jan 1, 1965

By E. M. Boatman, S. J. Pirson, R. L. Nettle

More than a decade ago some theoretically derived relationships were proposed that permitted the prediction of the relative ability of reservoir fluids (oil, gas, water) to flow simultaneously within the porous structure of rocks. While many successful predictions of fluid-flow ratios from wells have been made from electric logs, the theoretical deductions have not been subjected to laboratory verifications. For the relative permeability to liquid and gas, simultaneous flow of water and air was used, employing the familiar external-gas-drive technique. While in the process or water desaturation, the resistivities of the test cores (Woodbine sand) were measured. Their permeabilities varied from 10 to 280 md. The laboratory results indicated the need for changing the values of exponents in the theoretically derived formulas, whereas the form of the functions of resistivities and saturations remained as derived by theory. For the relative permeability to oil and water, the three-core dynamic technique was used on six cores. In this case it was found that the formulas were valid with but slight modification as derived by theory, to a sufficient degree of accuracy for engineering use and for well productivity prediction from electric logs. INTRODUCTION Conventional quantitative well log interpretation generally stops after reasonable values for formation porosities and water saturations have been established. Yet such in formation is insufficient to predict either the outcome or the desirability of well tests and completion, let alone the economic aspect of producing oil- and gas-bearing sections which might have been established by conventional log analysis. To give an engineering answer to such questions, it is necessary to predict the expected fluid flow ratios, the productivity index and the ultimate recovery from potentially productive wells. This problem requires in part for its solution a determination of the relative permeability characteristics of the potentially producing formations, both to oil (or water) and gas, and to oil and water.

Jan 1, 1965

By W. E. Anable

The Bureau of Mines studied the purification of commercially available yttrium by melting it in a 100-kw electron-beam furnace. Button-scale melts were made to determine the ultimate purification that could be attained by melting yttrium at 1,733° to 1,770° C at low pressure (0.05 to 0.1 micron) for 1 to 120 minutes. In addition, numerous melts were made to study the effect of doping yttrium with carbon, 17 selected metallic additions, and 3 compounds. Except for nickel and zirconium, the metallic impurities in yttrium were lowered significantly on extended treatment; silicon was lowered only slightly. The nonmetallic impurities} oxygen, nitrogen, and carbon, were not lowered except on short exposures. In isolated instances, the oxygen content was lowered from 5,860 ppm to about 5,000 ppm. In most instances the carbon con-tent was lowered from 545 to about 220 ppm in 20 minutes and then increased again. It was concluded that yttrium cannot be purified by direct heating or by the doping technique employed.

Jan 1, 1965

By D. L. McDanels, J. W. Weeton, R. W. Jech

An investigation was conducted to determine the stress-strain behavior and tensile properties of metallic composites and to relate them to the properties of the base materials. Tungsten fibers in a copper matrix were chosen as the model sys-tem to investigate these properties. Room-temp-atzcre tensile and dynamic -modulus tests were used To meet the demand for improved structural materials, considerable effort is being directed toward the creation of composite materials. One such material under investigation is the fiber-reinforced composite, in which a ductile, relatively weak matrix is reinforced with high-strength fibers. Some work has been done on the reinforcement of metallic matrices with metallic fibers1"5 as well as with ceramic-whisker reinforcement. Summaries of much of this work have been published by Mach-lin7 and Baske~.' Work done at the Lewis Research Center of NASA-" has involved the making and testing of composites composed of a fiber, tungsten, and a matrix, copper, which were insoluble in each other. An equation was presented that showed the relation between the ultimate tensile strength of the composites and the strengths and relative volume percents of the components. This relation was verified experimentally for composites containing fibers extending the full length of the specimen as well as for composites reinforced with short-length or discontinuous fibers. Since the publication of the preliminary results,9'10 additional data have been obtained. This paper presents these data as well as analyses of the stress-strain behavior and the mechanics of deformation of uni-axially oriented, fiber-reinforced metallic composites, in which both components are mutually insoluble. EXPERIMENTAL PROCEDURE Composites were made with high-purity copper as the matrix and 3-, 5-, and 7-mil-diam tungsten wire as the reinforcing fiber. Some specimens were made in which the reinforcing fiber extended completely through the full length of the composite test section. The fibers were placed in ceramic to determine these properties. The composites were reinforced with either continuous or discontinuos tungsten fibers. The tensile properties and stress-strain behavior of composites reinforced with either type of reinforcement were similar, and in both cases the full strength of the fiber was utilized. tubes to insure axial orientation and infiltrated with copper at 2200°F for 1 hr. Composites were also made with short-length (3/8 in. long) 5-mil-diam tungsten fibers as discontinuous reinforcement and infiltrated under the same conditions. The reinforcing fibers in both cases were longitudinally oriented in the direction parallel to the tensile axis. Room-temperature tensile tests were conducted on the composites, stress-strain curves were obtained, and ultimate tensile strength and elongation were measured. Dynamic modulus of elasticity, based upon the resonant frequency induced in the flexural mode of vibration, was also determined for the composites and the components. A more detailed discussion of the experimental procedure employed in this investigation may be found in Ref. 11. RESULTS Room-temperature tensile tests were conducted on 3-, 5-, and 7-mil-diam tungsten wires which had been annealed for 1 hr at 2200°F and show the tensile strength of the wires to be 331,000, 327,000, and 290,000 psi, respectively. Since all the composites were infiltrated under these conditions, the strengths were considered to represent the strength of the fibers in the composites throughout this study. The average tensile strength of the annealed copper used as the matrix in this investigation was 27,800 psi. Results of room-temperature tensile tests on composites reinforced with 3-, 5-, or 7-mil-diam tungsten fibers are plotted as functions of composition in Fig. 1. These data represent previously reported datag,l0 as well as data more recently obtained. The line shown on each curve represents a prediction of tensile strength as a function of composition; the calculation of this line was explained in Refs. 9 and 10. A similar plot is presented in Fig. l(d) for composites reinforced with short-length, discontinuous 5-mil-diam tungsten fibers. Again, both the previously reported and the recent data are presented, and the line shown is identical to that shown for

Jan 1, 1965

By Manuel Gomez

The heat contents of thermally dried lignite, subbituminous B coal, and their corresponding low-temperature chars were determined at various temperatures below the highest temperature to which these materials had been exposed before testing. Similar studies were made on high-temperature char and coke, spent shale, and ash prepared from both coal and spent shale. Heat content of the carbonaceous materials tested correlated well with temperature. Heat con-tent results for spent shale compared well with the published results. Statistical analysis of experimental data together with published information showed moisture, volatile matter, carbon content, and temperature to be the principal variables influencing the specific heat of coal. The specific heat of devolatilized carbonaceous substances, char and coke, approached that of graphite as the carbonization temperature was increased. The elemental specific heats of coal constituents, estimated from the ultimate analysis and the specific heat of coal, compared favorably with published elemental specific heats.

Jan 1, 1965

By G. W. Birge

Fifteen coal samples, representing the Winifrede, Chilton, Alma, No. 2 Gas, Powellton, Eagle, Douglas, Sewell, Beckley, Pocahontas No.4, and Pocahontas No.3 beds in Wyoming County, and five samples, representing the Fire Creek, Pocahontas No.6, and Pocahontas No.3 beds in Mercer County, W. Va., were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses and agglutinating values were determined for all coals. The coals were mostly strongly coking and low in ash and sulfur content. Dry, mineral-matter-free fixed-carbon content of the Wyoming County coals ranged from 63.0 to 83.4 percent. The Mercer County samples were all low volatile in rank. Yields of carbonization products were generally in accord with yields from similar rank coals of the Appalachian region. Because of their expanding tendencies, most of the medium-and low-volatile coals would require blending with lower rank coal for normal coke production.

Jan 1, 1965

By G. W. Tuffnell, S. Floreen

Three Fe-18 pet Ni-base ternary alloys cortaining carbon, molybdenum, or cobalt were aged to pgroduce hardening by carbides, Ni3Mo, or ordering, respectively. Each alloy was tested in rotating-beam fatigue tests after hardening to 195 ksi ultim.ate tensile strength. The fatigue properties of three alloys soere essentially identical. The results suggest that tlze fatigae strength of an igron-base alloy should depend primarily upon the tensile strength, and not iipon the hardening mecaanisrn. THE fatigue strengths of many steels have been found to be directly related to their ultimate tensile strengths. For ultimate strengths below 200 ksi, the fatigue endurance limit at 107 to 10' cycles is approximately half the ultimate strength. Essen- tially all of the steels that have been tested, however, have been hardened by carbon. Thus it is not certain whether the relationship between fatigue and ultimate strengths is a general one that applies for other types of hardening in steels, or whether it applies only for the particular method of hardening by carbon. The recent developments of the martensitic precipitation-hardened stainless steels and the marag-ing steels have shown that it is possible to achieve high strengths in iron-base alloys by other hardening mechanisms than that due to carbon. Therefore, it is now possible to compare the fatigue properties of several iron alloys having the same ultimate strengths but hardened by different mechanisms. For the present study a binary Fe-18 pct Ni martensite was selected as a base material. This particular matrix composition has been found to have deformation characteristics very similar to pure iron.' Three ternary alloys were prepared by adding either 0.23 wt pct C, 5 wt pct Mo, or 20 wt pct Co to this base composition. After suitable heat

Jan 1, 1965

By T. S. Lovering

The use of geothermal energy is expanding very rapidly. This type of energy has proven commercially profitable for generation of electricity, for space heating, process heating, auxiliary heating of water in conventional steam power plants and for recovery of chemicals contained in natural hot water and steam. Two types of geothermal energy sources are recognized: 1) hot springs in regions of nearly normal heat flow that tap a deep reservoir through which water moves slowly to a hot springs conduit and then rapidly to the surface; 2) hyperthermal areas in which the water is heated by a relatively concentrated heat source related to volcanicity. If there is a geologic trap that provides a geologic analog to a steam boiler, as at Larderello, Italy, the hyperthermal area will have a convecting system that develops superheated water at relatively shallow depth and may provide natural steam in large quantities. If a hyperthermal area is to be productive for a long time, the underflow into the reservoir should be slow enough to allow the heat source and convective system to heat the underflow to the working temperature, and the production rate must not exceed this rate of underflow. A model based on a typical aquifer suggests that the rate of movement of water through the reservoir be such that a few years are spent in transit between isotherms that are spaced about 2°F apart. The possibility of finding blind geothermal areas is illustrated by discussion of the techniques developed in evaluating the subsurface temperatures in the East Tintic district of Utah where a map of isotherms at water level (2000 to 2000 ft below the surface) shows that a hyperthermal area may exist a short distance southeast of the mining district. Very nearly all of the energy that man currently uses comes ultimately from the sun's radiation. This includes water power, fuels such as wood, peat, coal and petroleum, the wind and all our animal power. In the paper summarizing a conference on solar energyl6 the average amount of solar energy received daily on the earth is taken at about 1 cal per m2 per min or slightly less than 2 pcal per cm2 per sec; this is almost exactly the amount of energy on the average that the earth liberates in regions of normal geothermal gradient due to its own internal heating. In many places, however, the energy released is many times the average and in some of these hyperthermal areas, geothermal steam is used for generation of electricity, and hot springs are used for heating buildings and private dwellings, process heating, auxiliary heating of water in conventional steam power plants, and chemicals may be recoverable from both hot water and steam. The use of hot springs waters for heating houses goes back hundreds of years but until recently was confined to a few dwellings close to the hot springs. In Korea, some houses had hot spring water channeled through conduits in the floor centuries ago and thus the Koreans can be credited with pioneer development of radiant heating. In Iceland at present nearly a third of the population uses natural thermal water for domestic heating." The Reykjavik system pipes hot spring water at about 94°C throughout the city and has devised insulated double pipes that allow the water to be piped for some 25 km with a drop of only 1°C for every 5 km. The actual cost to the Icelandic consumer is only one-third the cost of heating by imported coal and yet the industry is one of the most profitable in Iceland. The most profitable use of geothermal energy has been its conversion into electricity which can be transmitted economically much greater distances than hot water. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam 60 years ago — in 1904. He installed his first steam turbine, with a capacity of only 250 kw, in 1912 as the result of a local quarrel with the power company which furnished the current required in the Larderello chemical industry - an industry that then dated back nearly a century. As experience was gained in drilling deep holes to tap geothermal steam and in converting it to electric power, the capacity of the installation of Larderello gradually increased, but was all destroyed by the Germans during their retreat from Italy in the closing

Jan 1, 1965

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grind-ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1965

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By W. D. Potter, E. T. Peters

Single-crystal films of boron have been prepared by thermal reduction of purified BCl3 with subsequent deposition of boron onto oriented silicon substrates. The structural properties of films prepared under various experimental conditions have been determined by light microscopy and "grazing-" angle electron-diffraction analysis. An orientation relationship is proposed for silicon and a-rhombo-heclral boron which can be described as: (111)Si (112)B; [110]Si [110]B ElEMENTAL boron is known to have a high energy gap* and consequently has potential value as a high- *Energy gaps of 1.35 to 1.55 ev1-3 and 2.0 ev4 are reported for ß-rhombohedra1 and a-rhombohedra1 boron, respectively. temperature semiconductor.5 Exploitation of this property, however, has been hampered by the unavailability of pure, single-crystal boron. Two recent symposia6,7 have treated the subjects of purification, crystallization, crystal structure, and properties of boron and provide a foundation for further investigation in these areas. The structure, lattice constants, and observed ranges of stability for four reported polymorphs of boron8°12 are listed in Table I. The rhombohedral structures are generally accepted as true polymorphs whereas the tetragonal structures are believed to be transient. Most currently available single crystals of boron are grown by Czochralski and floating-zone methods. Unfortunately, these crystals generally contain numerous defects and are highly strained as a result of the polymorphic transformations and thermal contractions which accompany cooling. Recently, Armington, Potter, and Tanner13 have reported the formation of single-crystal films of boron on silicon single-crystal substrates through thermal reduction of BC13 by hydrogen. Boron E. T. PETERS, Junior Member AIME, is Senior Scientist, ManLabs, Inc., Cambridge, Mass., and W. D. POTTER is Research Chemist, Air Force Cambridge Research Loboratories, L. G. Hanscom Field, Bedford, Mass. formed at temperatures near 1000°C was identified as the a-rhombohedra1 form, consistent with expectation. The present paper describes a continuation of this work with specific reference to characterization of the structural features of the deposited boron films. The ultimate goal of this program is to produce large-area single-crystal films of a-rhombohedra1 boron to be used for electrical and optical studies by other workers. PREPARATION OF BORON FILMS The experimental procedure of preparing thin films is similar to that described by Theuerer14 for the epitaxial growth of silicon by thermal reduction of SiC14 and has already been described as applied to the preparation of boron thin films.13 Briefly, a mixture of BCl3 vapor and dry hydrogen is passed over a heated silicon substrate. Thermal reduction of the BC13 allows deposition of boron on the substrate. The substrates were {111}-oriented, single-crystal silicon. Square specimens 0.63 cm on an edge by 0.1 to 3.0 mm thickness were prepared by

Jan 1, 1965

By F W. Irwin

In recent years, a number of significant developments have occurred in the steel industry which are no-table and of general interest. This paper is confined to the steel-melting phase of the business. The development of high production rates on Stelco's Basic Open Hearth furnaces is chronologically summarized. Al-though various aspects of this subject have been presented previously, this paper summarizes the developments in high fuel rates, the usage of basic refractories, low and high oxygen rates and hearth maintenance. Background T HE interest which has been shown in steelmaking techniques in the past few years has been due, primarily, to the extremely high production rates obtained. Upon further study of the facilities and techniques employed to generate this steel at record rates, tonnage oxygen appears as the common factor. It can be stated that tonnage oxy-gen has revolutionized steelmaking techniques to a degree never before encountered. It was only about ten years ago that the use of large amounts of pure oxygen in a steelmaking

Jan 1, 1965

By T E. Tibbetts

This paper deals with coal sampling in general and with mechanical coal sampling in particular. The necessity of obtaining representative samples is emphasized. Other sections of the paper are devoted to the design and selection of automatic samplers, with a consideration of the three main types, and the testing, operation and maintenance of these samplers. The cost of the installation of an automated sampling system must be related to the value of the material to be sampled, to the volume of coal involved, and to the savings in labour and economy which can be achieved. Introduction T HE Committee?:; on Coal Sampling of the Coal Study Subsection, Thermal Power Section (Eastern Zone), Canadian Electrical Association, was established in November, 1963, to "study the various problem areas of coal sampling." The first undertaking of the Committee was to at-tempt to survey the problem areas of coal sampling through an evaluation of coal sampling difficulties as experienced at both the plant design and operational levels within the electric utilities represented on the Committee. The results of this enquiry indicated that satisfactory answers to almost any conceivable

Jan 1, 1965

By Manuel Gomez

Carbon number distributions were obtained for tar acid fractions from five low-temperature tars by low-ionizing voltage mass spectrometry. Quantitative data for phenols representing seven structural compound types were examined by statistical analysis. It was shown that for the phenols discussed, the data could be represented by regression equations expressing phenolic concentration as a function of the reciprocal of the carbon number and the carbon-to-hydrogen ratio of the parent coal. The total concentration of each structural type present was found to depend on the molecular weight and boiling point of the initial member of the group. Carbon distribution data for the tar acid fractions studied support the view that low-temperature tars contain the same chemical compounds but in different proportions.

Jan 1, 1965

By John W. Buch

Hydraulic cutting tests made on samples of Pennsylvania anthracite (3,700 psi and 260 gpm) were promising enough for the Bureau to establish a full scale experiment in an anthracite mine. Water pressure and quantity for mining anthracite were arbitrarily established at 5,000 psi and 300 gpm (1,000 hp). For full-volume flow, hydraulic pressure is controlled by orifice size with the displacement pump. The hydraulic jumbo was designed for maneuvering on pitches from 0° to 20° in any direction and for a coalbed ranging in thickness from 10 feet 6 inches to 15 feet. All motions of the jumbo are by oil hydraulics. Jet flow is controlled (start-stop) at the face, through an interlocked pushbutton system. One button is in the operator's cab; one, at the pump station; and one (a safety shutoff), near the mining face. To December 1962, 7,400 tons of bed material had been mined at an average rate of 0.800 ton per minute, with an average power requirement of 14.125 kilowatt-hours per ton. In January 1963, the objective was changed from an engineering-development basis to a research basis--to determine, ultimately, the most efficient level of operating characteristics for maximum response, as measured by mining-out rate. This research phase of the project is not yet complete, but conclusions, and the method of arriving at them, will be made the subject of another Bureau publication. It should be noted that as of December 1963 nearly 13,000 tons of bed material had been mined, at rates as high as 1. 3 tons per minute for a complete face advance.

Jan 1, 1965

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent no improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver-bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores char because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965