Search Documents

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

By Claiborne C. Van Zandt

THE heavy postwar demand for Portland Cement has created shortages that are gradually being overcome by increases in plant capacity. In the post-war period, the Lone Star Cement Corp. has expanded several of its existing 15 plants and has built 2 new plants, now in operation, with a third new plant under construction in Brazil, of design somewhat different from that of the two preceding ones. The new domestic plants are located at Lone Star, Va., near Roanoke, and at Maryneal, Tex., near Sweetwater, and went into operation during 1951. Each plant is equipped with two rotary kilns and has an initial capacity of 1,500,000 bbl per year, or 6,000,000 sacks. The total cost of each plant was about $10,500,000, and on this basis $7.00 in 1951 money are required per bbl of annual capacity; at 376 lb per bbl, this corresponds to $37.00 per ton of output. The investment corresponds to approximately $80,000 per hourly-wage earner employed. The purpose of this paper is to describe the most interesting design features of the two new and almost identical Lone Star plants. Why the Dry Process Was Chosen The two new domestic Lone Star mills employ the dry process because: 1-The raw materials at both properties are particularly suitable and can be dried very, readily. 2-The Maryneal, Tex., plant does not have water available for slurry. 3-Very substantial kiln fuel savings can be obtained. 4-Dry raw grinding reduces ball and liner wear and- general maintenance, without any sacrifice in power. Operating costs to date have more than justified the choice of the dry process for these two plants. Raw Materials The chemical composition of Portland Cement raw material after crushing, grinding, and mixing, but before burning, is about as follows: [ ] sometimes tailings from an iron ore concentrating plant. Certain objectionable materials occur in raw mix: magnesia, limited in cement to 5 pct, in excessive amounts; alkalies, as sodium and potassium; phosphorous; and sulphur, generally present in coal and oil. The Roanoke raw, materials are dense limestone and shale. The Maryneal materials are soft limestone and a hard brittle clay that can be handled much like shale. Sand and iron ore are required in small quantities. General Plant Layout and Construction The two plants are so similar that one joint description will cover both, with such exceptions as will be especially indicated. The crushing plant is located in the quarry, and raw material is conveyed by belt to the storage building, where all materials are stored and handled. Fig. 1 identifies the various structures of the Roanoke plant. The large storage building is used for the storing and handling of all materials, including limestone, shale, sand, iron ore, coal, clinker, and gypsum. Directly adjoining the storage building is a structure under a similar arched roof, containing the raw and clinker grinding departments and the electrical substation. The discharge ends of kilns and coolers, and coal or gas burning equipment are also placed at one end of the mill building. The 340ft long kilns extend away from the main buildings to form the long leg of an L, at the end of which is the feeding and kiln dust collecting equipment, and the raw blending silos are conveniently located adjacent to the feed end of the kilns. The machine shop, storeroom, electrical shop, foremen's office, service rooms, and meeting hall are combined in one structure in the center of the plant, and the office and laboratory are close by. The cement silos and packhouse do not have to be tied directly into the manufacturing process and are therefore located at a point convenient to the railroad tracks.

Jan 1, 1952

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young's moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.' In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young's modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young's modulus and substantial magnetic permeability.' Young's modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.' This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.' The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).'. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.' Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young's modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.', " In this method Young's modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101' dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young's Modulus Values at 25°C: The modulus values of O', 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By A. J. Kraemer, H. M. Thorne

The following account of oil-shale operations in Australia is based upon infor- mation obtained by the authors while visiting Australia from September 15 to October 7, 1947, supplemented by published data, and augmented by analyses of samples of oil shale and its products at the Oil-shale Research and Development Laboratories of the Bureau of Mines at Laramie, Wyo. The primary objective of the authors' trip to Australia was to obtain, first hand, information regarding the equipment and methods used by National Oil Proprie- tary, Ltd., at Glen Davis, New South Wales, in mining oil shale, extracting oil from it, and refining the shale oil. This company was operating the only oil-shale plant that had been active in Australia since 1945. The plant comprised an oil-shale mine, 104 modified Pumpherston (Fell) retorts in 2 batteries, a hele refinery, and a 3-inch gusoline pipeline to the railroad loniing terminal t Sun Junction, 30 miles away. There were, also, the usual and necessary any uralities, such as a power house, mechanical shops, offices, and laboratories One Information regarding the company's operations was wance because of its bear- Ing upon the synthetic liquid fuels program of the Bureau of Mines, pursuant to the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C., 321-325, as amended). objective of the Bureau's program. In accordance with the maniate of the Act, is to furnish American industry cost and engineering data necessary for the development of synthetic-liquid fuel industry, and an obvious means of obtaining some of these data is to learn how oil shale is being mined and retorted and how shale oil is re- rined in countries where these operations have been conducted on a plant scale for many years. The authors spent 2 weeks at the plant of National Oil Proprietary, Lt., at Glen Davis, and were afforded every opportunity to obtain letailed and specific information regarding all aspects of the company'a operations.

Jul 1, 1951

By John W. Buch

Safety and cost in mining coal beds under the extreme pressures found at depth, full extraction to conserve resources, and even surface subsidence to minimize damage of improved areas have directed much well-deserved attention, in the United Kingdom; to roof-control methods. Because the effects of pressure will be felt intensely as our Pennsylvania anthracite mines grow deeper, the senior author took advantage of an opportunity afforded by a mission to Europe3/ to observe, to a limited extent, the effects of pressures found in deep mines and the manner in which they are con trolled. Organized research relating to strata control has been carried on in Great Britain for nearly 25 years. These activities have been ably outlined by Dr. D. W. Phillips.4/ Physical properties of coal-measure rocks, movements of roof and floor, and types of face and roadway supports have been investigated. Same of the forces induced by the extraction of coal have been measured. The results of this research have been publicized and openly discussed, and much progress has been made in establishing a better factual understanding of roof-control problems and their solution.

Jan 1, 1951

By J. A. Hafford, J. K. Kerver, J. G. Richardson, P. M. Blair, J. S. Osoba

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By F. M. Lewis, J. F. Myers

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By T. E. Ockershauser

The Southwest Antioch Oil Field located in T2&3N - R2&3W, Garvin County, Okla., was discovered in February, 1946, by The Globe Oil & Refining Co. and The Vickers Petroleum Co. at their Melinda Gibson No. 1. Oil production was encountered at a depth of 6,525 ft in 14 ft of lower Pennsyl-vanian sandstone. The producing sand, locally called the ."Gibson" or "Third Deese," is a sand bar deposit strung along the west flank of the Pauls Valley uplift in a northwest-southeast direction. The oil reservoir is defined to the east by the edge of sand deposition along the uplift and to the west by the gradation of sand into shale. Within the Antioch Unit, the sand dips from 150 to 400 ft per mile southwesterly and has a pay thickness varying from 10 to 55 ft and averaging 28 ft. Several areas of Gibson production have been developed, including the Katie pool on the south, the Elmore Area of the Southwest Antioch Gibson Sand pool. the Southwest Antioch Gibson Sand pool proper, the Southwest Maysville pool and the New Hope pool on the north. Production extends over a belt 22 miles long by about two miles wide and is continuous except into the Katie and New Hope pools. It appears that drilling will soon prove these intervening areas productive. To March 1, 1950, approximately 18,000 acres have been developed with 450 Gibson wells. It is likely this count will ultimately reach 32.000 acres with 800 wells. RESERVOIR The natural production of oil from the Gibson reservoir is primarily due to solution gas expansion though gravity also plays a part. There is no indication of water drive or evidence that an initial gas cap existed. Gibson oil has a stock tank gravity of 43" API and was saturated at the original reservoir pressure of 2.925 psi. It contained 1,3440 cu ft of gas per bbl in solution and had a high shrinkage of 70 per cent. Connate water amounts to 15 per cent. Reservoir temperature is 130°F. Porosity averages 15.5 per cent and permeability ranges from less than one md to over 1.000. Based on meacurement of 400 core plugs from 15 wells, 78 per cent of the permeabilities fell within the 10 to 1,000 md bracket and averaged l67. Primary oil recovery is estimated at 140 bbl per acre-ft or 22 million bbl for the present 137-tract unit. Due to unitization

Jan 1, 1951

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By James R. I. Henagan, William O. Crego

The Mamou Field, located in Evangeline Parish, La., is an elongated anticlinal structure on the downthrown side of a major east-west fault with oil and gas production from the upper part of the Wilcox formation. Two main producing horizons occur at an approximate depth of 11,500 ft and have been designated the Morein sand and the Deshotels sand. The upper sand (Morein) had an original bottom-hole pressure of 6,788 psig, which is some 1,500 psi above the normal pressure for that depth. Oil production with high gas/oil ratios and fluid analyses giving high shrinkage factors prompted a study of the reservoir in its early stages. The results indicated a closed reservoir producing under solution gas drive with low expected ultimate oil recovery. The early study of the Wilcox formation and its contained hydrocarbons resulted in the presentation of the data to the Department of Conservation of the State of Louisiana. with suggestions for field rules and a request for permission to inject extraneous water into the Morein sand. The water injection plans eventually led to complete unitization of working and royalty interests, to the construction of a gasoline plant, and to a central tank battery installation for the field. Deshotels sand wells were reworked to the Morein sand, and the water injection system was installed and ready for continuous operation in the early part of 1949. The injection of water was started in time to arrest the bottom-hole pressure decline at or near the bubble-point pressure. This injection was calculated to increase the ultimate recovery and to conserve natural resources. Pressure maintenance, the extraction of LPG products, and the sale of residue gas (early 1950) represent an attempt to produce an oil field with utmost efficiency. INTRODUCTION The two principal Wilcox oil horizons in the Mamou Field are the Morein sand and the Deshotels sand, occurring at 11,500 ft and 11,700 ft subsea, respectively. Minor oil production has been encountered in Morein stringer sands. (Fig. 1.) This paper deals only with the Morein sand, which is blanket over the Mamou Field. It is, however, segmented by the northwest-southeast "E" fault as shown in Fig. 2. The west segment is the area involved in the water injection pressure maintenance program. To date the east segment has operated largely under the influence of a strong water drive. The paper presents (1) a brief history of field development, (2) a resumé of reservoir conditions which led to the decision to inject extraneous salt water into the principal producing horizon, and (3) a summary of reservoir analysis and performance. FIELD DEVELOPMENT The Mamou Field is located in Evangeline Parish, La. The discovery well (J. B. Morein No. 1, now Unit No. 5) was completed in December, 1945, after penetrating 200 ft into the Wilcox formation. Initial production from the Morein

Jan 1, 1951

By R. M. Leibrock, J. E. Huzarevich, R. G. Hiltz

The various factors considered in recommending the initiation of a gas injection project in the southern portion of the Cedar Lake Field are discussed. Performance history under gas injection operations is reviewed and these data are analyzed, utilizing both the material balance method and the fractional flow and frontal advance expressions. Results of the analysis of the performance data indicate that the injected gas has contacted and affected at least 60 per cent of the reservoir and a substantial increase in ultimate recovery can reasonably be expected. By holding the reservoir pressure appreciably above the bubble point, the well productive capacities have been maintained substantially above the level predicted for primary operations. The analysis of the Cedar Lake project suggests that in certain limestone reservoirs, at least, the probable success of gas injection cannot be predicted simply from ohservation of permeability distribution throughout the pay section, as indicated by core analysis data, on either one or a number of wells. Further, the performance of this particular project fails to indicate any basis for classifying carbonate reservoirs in general as being inherently unsuited to a dispersed type gas injection program, thus indicating that each reservoir should be considered on its own merits, regardless of the composition of the reservoir rock. INTRODUCTION Early in the life of the Cedar Lake Field, an extensive data gathering program was initiated to provide an accurate record of reservoir performance characteristics. From the study of these data it was apparent that there was a critical need for supplementing the natural reservoir energy in order to maintain well productivities and obtain the maximum ultimate oil recovery. Accordingly, detailed engineering studies were made of the various methods of secondary recovery which might be applicable. As a result of these investigations, the decision was made to initiate a gas injection program of sufficient intensity to maintain reservoir pressure at approximately 600 psia, or some 274 lb above the bubble point pressure of 326 psia. A full scale dispersed type gas injection program has been in operation on leases of the Stanolind Oil and Gas Co. in the southern portion of the field for nearly five years, and sufficient performance data are now available to evaluate the benefits which have been derived from this project. It is the primary purpose of this paper to analyze the performance data for the Cedar Lake gas injection project and to point out the significance of the ohserved behavior with respect to certain hypotheses which have been advanced in recent years concerning the probable success of gas injection projects in limestone reservoirs. This paper properly should be regarded more on the order of a progress report, inasmuch as some revision in interpretation will undoubtedly be required from time to time as additional performance data are obtained, although the satisfactory performance of the project to date leaves little doubt as to the ultimate success of gas injection in the Cedar Lake Field. As a result of the success of the project to date, a unit was formed in the southern part of the field, effective March 1, 1951, for the purpose of continuation of the gas injection program. Participants in this unit are the Mid-Continent Petroleum Co. and Stanolind Oil and Gas Co. GEOLOGY AND STRATIGRAPHY The Cedar Lake Field is located in the northern portion of the Midland Basin area as shown in Fig. 1. The southwest portion of the field lies within a playa, or dry salt lake, which covers an area of approximately eight square miles. As might be expected, it was this lake which furnished the inspiration for the name of the field. Except for its value as a salt water disposal pit, this lake has succeeded only in magnifying the difficulties in developing this portion of the field. Typical of this section of West Texas, the area in general is relatively flat and has a semi-arid climate. The localized structure which favored the accumulation of oil is an anticline with approximately 100 ft of closure. The major axis of the structure extends in a general southeast-northwest direction. Originally this structure was defined by seismograph data, which have been subsequently confirmed by development. In general, the geologic column is typical of that found throughout the basin. From the surface to depth of approximately 1,800 ft, surface sands and undifferentiated red beds. probably Triassic. are encountered. Below this point to the producing horizon, all formations are of the Permian age.

Jan 1, 1951

By M. R. J. Wyllie, F. Morgan, P. F. Fulton

The importance of formation factor, F, not only in electric logging but as a fundamental rock parameter has recently been stressed.',: The desirability of investigating the range of variation of the resistivity index exponent, n, in the relationship I = S ;", where I is the resistivity index and Sw the water saturation as a fraction of the void volume of a porous medium, has also been urged.3 The magnitude and variation of n with saturation and rock texture is a subject not only of theoretical interest but also one of prime importance in the interpretation of electric logs. A simple technique has recently been developed which enables both F and u to he measured with high accuracy and which may also find acceptance as a convenient method for the determination of irreducible saturation attainment in the restored state method of core analysis. Experience has taught that reproducible measurements of F are possible only if the resistance measuring electrodes are so arranged with respect to a plane face on a porous medium that they are able to make electrical contact with substantially all entry pores in that plane. In practice this may be achieved by using a platinized-platinum gauze electrode backed by some absorbent material (such as felt) which has been saturated with a fluid identical with that used to saturate the porous medium. Applicatiorl of pressure to the electrode and absorbent material then forces the gauze against the plane face of the porous medium and simultaneously squeezes saline solution through the meshes of the gauze. By this means the electrode is in continuous aqueous contact with all pores and satisfactory and reproducible low resistance contact with the porous medium is achieved. Clearly this method, although satisfactory for measurements of F, cannot be applied to the making of continuous resistance measurements on a porous medium while capillary pressure desaturation is being carried out. However, accepting the principle that for satisfactory results electrical contact must be made between a measuring electrode and all pores adja- cent to that electrude, methods of bringing electrodes into intimate contact with the surfaces of porous media were investigated. Two methods were ultimately found to be satisfactory: in the one, the metal electrode is formed on the required portion of the porous medium by the use of a metal spray gun, while in the second the electrode is painted on with an ordinary camel's hair brush. The first method has the advantage of permitting the use of any metal which can be sprayed, but has the disadvantage of requiring rather elaborate and expensive equipment. The second method is presently limited to silver electrodes although in principle other metals, e.g. platinum or gold, could be used. Moreover, the method is so simple and cheap, and has been found to be so satisfactory that it will be described in some detail. The core being investigated is cut into a right circular cylinder and is extracted and dried in the usual manner. The ends are then lightly painted with silver conducting paint* of the type used in printed electrical circuits. The quantity of paint used is not critical but the recommended, minimum compatible with entirely coating the core ends is recommended, particularly on the end that contacts the barrier. The core is then dried at atmospheric temperature for one hour or for shorter periods at any suitable elevated temperature up to about 110°C. It will be found that silver coatings so prepared are not only strongly adherent but also permeable and the core may be the core may be desaturated by the ordinary capillary pressure technique through one of the coated faces. The same permeability is characteristic also of thin metal coatings formed using the spray-gun technique. An ordinary Lucite capillary pressure desaturation cell has been adapted to a form suitable for measuring the resistivity of the saturated silver faced cores both at 100 per cent saturation (i.e., F) and at intermediate saturations down to the irreducible minimum. This has been achieved as follows: A Coors porcelain barrier, having a displacement pressure of c 30 psi was grooved across a diameter. Dimensions of this groove were c 1 mm deep and 1 mm wide at the top. The groove was then painted thickly with silver conducting paint, the paint in the groove being extended lightly over the edges of the groove for a distance of c 1 mm on each side. A 30 gauge silver wire was then arranged in the groove in a form of a spring bow, each end of the silver being held at diamet~ically opposite ends of the groove by means of plastic cement. The arc of the bow at its highest point was arranged to be a millimeter or so above the face of the barrier, while one end of the bow wire was led by means of a pressure-tight connection through the wall of the capillary pressure cell. The groove in the barrier was then Surrounded by suitably cut portions of Kleenex in the conventional manner so as to ensure capillary continuity from core to barrier, and the core placed on the barrier. The weight of the core distorted the silver spring bow and good electrical contact was thereby made between the outside of the cell and the lower painted silver electrode. Electrical connection to tile top painted silver

Jan 1, 1951

By P. G. Nahin, A. Grenall, R. S. Crog, W. C. Merrill

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By B. E. Morgan, C. K. Dumbauld

The need for a low-strength cementing composition for use in well cementing is reviewed and results are presented of laboratory and experimental field tests of a modified cement having a controlled ultimate tensile strength of approximately 200 psi. The modified cementing composition may he prepared from either high early strength or normal portland cements by the addition of bentonite clay and a suitable agent for dispersing and controlling the set of the slurry. Substitution of the modified cement for conventional slow-set cements may give better completion results in many wells because the modified cementing composition has lower set strength, lower slurry density, and greater slurry stability than conventional cement slurrieh. The lower ultimate strength allows greater penetration with less shattering of the set cement when perforating casing and cement. The lower elurry density allows the placement of longer columns of cement slurry, and the greater slurry stability reduces the possibility of having an uncemented section caused by the settling of cement particles before the cement set.. INTRODUCTION High strength lias always been one of the accepted criteria of a good cement. During the early use of portland cement in well cementing. emphasis was placed upon securing cements with higher strengths. In 1931, Barkis' reported that, "Normal oil well cements have been improved to develop greater strengths and uniformity of product, which has aided in producing successful jobs in cementing the deeper strings." As long as most wells were completed by the open-hole method. the use of cements having high strengths seemed desirable, and there was no objection raised against high-strength cementing compositions. For a number of years. how-ever, the industry has been completing a large numher of wells by setting and cementing casing through productive horizons and then obtaining production by gun-perforating the section of casing opposite the desired interval. Although this method has been generally successful, difficulties have been experienced in some cases in completing or recompleting wells because of apparent lack of adequate penetration by the bullets through the casing and surrounding sheath of cement and into producing formation. In addition to the penetration trouble: there have been indications that fracturing and shattering of the set cement by perforating might he a contributing factor in causing the failure of some jobs to exclude water or gas from oil producing zones. The possibility that cements having high set strengths were contributing to til difficully ill obtaining satihfartory perforating results has re. ceived attention during recent years. Gun perforating tests conducted in 1944 showed that the depth of bullet penetration into set cement varied with the hardness of the cement, the greater the strength of the cement the less being the penetration. In 1946, Farris2 pointed out that high strength cements were not needed in well cementing, and in 1947, data published by Oliphant and Farris3 showed that set cement was perforated without shattering at approximately 150 psi tensile strength. whereas at approximately 300 psi tensile strength severe cracking and shattering occurred. Oliphant and Farris suggested that wells be perforated at the proper time interval after placement of the cement so that the set cement would have the desired strength. Several difficulties may he encountered in trying to perforate a cement job at the correct time to catch the tensile strength near 150 psi. The rate of strength development of different cements varies considerably. This fact is illustrated by results of tensile strength measurements presented in Fig. 1. These data show that at 175°F the tensile strengths of three conventional slow-set cements varied from 75 to 235 psi at the end of 12 hours. After 24 hours, the tensile strengths varied from 200 to 455 psi. The rate of strength development is affected. also. by the temperature of the forniation, and this adds to the uncertainty of perforating at the rorrect time, since accurate well cementing temperatures may not he known in many cases. Furthermore, in the recomple-tion of wells it is sometimes necessary to perforate cement which has set for a long period and has developed maximum or final strength. In view of the apparent need for a cementing composition having a controlled ultimate strength, an investigation was

Jan 1, 1951

Jan 1, 1951

By H. G. Warrington

Abstract As part of the active development programme pursued by Dominion Magnesium Limited since 1945, a modern extrusion plant was erected and has been in operation for about twelve months. The only source of nigh purity magnesium in the world, Canadian metal is produced by metallurgical processes within the frame-work of the mining industry, which gives a different viewpoint to every phase of production from other world suppliers of commercial grade metal whose operations are based on chemical industries and techniques. The superior properties of corrosion resistance and grain refinement have aided a programme of standardization, reducing the number of alloys supplied in extruded form from seven to four as an aid to economic production. The first big step was the development of a general purpose alloy known as AZ?21x covering all decorative and medium stressed applications, which will supersede two older alloys. Sales approaching a million feet in this alloy show that it bids fair to become the 'mild steel' of the magnesium industry, its applications ranging from terrazzo floor strip to textile machinery and television mast components. In the high stressed field, metallurgical features preclude low-cost extrusion of the older high-strength alloys, but recent development of a magnesium alloy containing zirconium promises an easily workable metal. Hitherto produced by expensive chemical additions, research now shows that the alloy can be produced by metallurgical means, which may make this alloy available for a wide range of commercial applications. Thus the future development programme for extruded products in the form of tube, bars, shapes, and structural angles and channels may evolve two alloys to cover all applications for strengths up to 52,000 lb. per sq. in. Such standardization is the result of taking advantage of the physical and metallurgical properties of high-purity magnesium instead of accepting techniques based on metal produced by older processes.

Jan 1, 1951

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By J. E. Huzarevich, R. M. Leibrock, R. G. Hiltz

The various factors considered in recommending the initiation of a gas injection project in the southern portion of the Cedar Lake Field are discussed. Performance history under gas injection operations is reviewed and these data are analyzed, utilizing both the material balance method and the fractional flow and frontal advance expressions. Results of the analysis of the performance data indicate that the injected gas has contacted and affected at least 60 per cent of the reservoir and a substantial increase in ultimate recovery can reasonably be expected. By holding the reservoir pressure appreciably above the bubble point, the well productive capacities have been maintained substantially above the level predicted for primary operations. The analysis of the Cedar Lake project suggests that in certain limestone reservoirs, at least, the probable success of gas injection cannot be predicted simply from ohservation of permeability distribution throughout the pay section, as indicated by core analysis data, on either one or a number of wells. Further, the performance of this particular project fails to indicate any basis for classifying carbonate reservoirs in general as being inherently unsuited to a dispersed type gas injection program, thus indicating that each reservoir should be considered on its own merits, regardless of the composition of the reservoir rock. INTRODUCTION Early in the life of the Cedar Lake Field, an extensive data gathering program was initiated to provide an accurate record of reservoir performance characteristics. From the study of these data it was apparent that there was a critical need for supplementing the natural reservoir energy in order to maintain well productivities and obtain the maximum ultimate oil recovery. Accordingly, detailed engineering studies were made of the various methods of secondary recovery which might be applicable. As a result of these investigations, the decision was made to initiate a gas injection program of sufficient intensity to maintain reservoir pressure at approximately 600 psia, or some 274 lb above the bubble point pressure of 326 psia. A full scale dispersed type gas injection program has been in operation on leases of the Stanolind Oil and Gas Co. in the southern portion of the field for nearly five years, and sufficient performance data are now available to evaluate the benefits which have been derived from this project. It is the primary purpose of this paper to analyze the performance data for the Cedar Lake gas injection project and to point out the significance of the ohserved behavior with respect to certain hypotheses which have been advanced in recent years concerning the probable success of gas injection projects in limestone reservoirs. This paper properly should be regarded more on the order of a progress report, inasmuch as some revision in interpretation will undoubtedly be required from time to time as additional performance data are obtained, although the satisfactory performance of the project to date leaves little doubt as to the ultimate success of gas injection in the Cedar Lake Field. As a result of the success of the project to date, a unit was formed in the southern part of the field, effective March 1, 1951, for the purpose of continuation of the gas injection program. Participants in this unit are the Mid-Continent Petroleum Co. and Stanolind Oil and Gas Co. GEOLOGY AND STRATIGRAPHY The Cedar Lake Field is located in the northern portion of the Midland Basin area as shown in Fig. 1. The southwest portion of the field lies within a playa, or dry salt lake, which covers an area of approximately eight square miles. As might be expected, it was this lake which furnished the inspiration for the name of the field. Except for its value as a salt water disposal pit, this lake has succeeded only in magnifying the difficulties in developing this portion of the field. Typical of this section of West Texas, the area in general is relatively flat and has a semi-arid climate. The localized structure which favored the accumulation of oil is an anticline with approximately 100 ft of closure. The major axis of the structure extends in a general southeast-northwest direction. Originally this structure was defined by seismograph data, which have been subsequently confirmed by development. In general, the geologic column is typical of that found throughout the basin. From the surface to depth of approximately 1,800 ft, surface sands and undifferentiated red beds. probably Triassic. are encountered. Below this point to the producing horizon, all formations are of the Permian age.

Jan 1, 1951

Accident prevention in industry is a task as important to the ultimate result of an undertaking as efficient machines, good tools or trained operatives. In fact, like many qther phases of industry today, "Accident Prevention" or "Safety Organisation" has developed in this century, to a degree that is now acknowledged as an integral part of industrial thought and planning. This has not always been the case, as the following snap-shot picture of the past illustrates.The Broken Hill Proprietary Company recently celebrated at Whyalla the Jubilee of the opening of the Iron Knob Tramway. On that occasion a dinner was tendered to the pioneers, and in talking to the Writer of the early days one of the old gentlemen present could not refrain from recounting some of the accidents he had seen or experienced.Several such incidents were recounted at length, after each, the old fellow would say, "An' there weren't no safety officers or compensation in them days".The Broken Hill Proprietary Company Limited was a pioneer of safety in Australian industry and considerable success has followed its activity in this connection; the accident rate of the steel industry now compares satisfactorily with that of any other industrial undertaking. A measure of 'the success of the safety organisation, is, that in recent years, despite extensive construction programmes at various centres, and despite a heavy labour turnover, a decreasing accident rate has been maintained. This success, in the Writer's opinion, arises from the fact that by its early attention to plant protection, the introduction of safety standards and further through the interest and energy of departmental superintendents and foremen, the...

Jan 1, 1951