Search Documents

By Anand Kumar Agrawal, Kinzel Klaus Peter, Lorenzo Micheletti, Cristiano Castagnola, Horst Kappes, Andre Oliveira, Björn Rösner, Philippe Bermes

Blast furnaces are widely employed today for iron production all around the world, with a total production of around 1.2 billion tons per year. Its operating principle, which relies on usage of coke to reduce the ore, to ensure the permeability in the reaction vessel, to maintain its flexibility of operation and acceptability for varying qualities of iron ores. The blast furnace route is widely considered as the most economic and efficient route of iron production, however it is based on fossil energy carriers. The blast furnace route has undergone significant developments in terms of energy efficiency in the last decades, which led to a substantial reduction in the use of fossil reduction materials. Being an energy intensive process, competitiveness and cost saving in the blast furnace plant was always strongly related to the saving of energy and hence reduction of CO2 emissions. In addition to this, EU emissions trading system (EU ETS) as a cornerstone of the EU's policy in response to climate change has set new “challenges” for iron production in Europe. Paul Wurth has always been deeply involved in the development of energy saving technologies for blast furnaces. In the following a review of energy saving achievements developed in the last decades will be presented and the potential of available CO2 saving technologies will be summarized. Additionally, an outlook about the potential of future technologies, concepts and their impact on the blast furnace and the steel plant’s energy balance will be discussed. Finally, the replacement of carbon by hydrogen as reduction agent in the steel plant will be reviewed, with special focus on a comparison of costs and incentives.

Oct 1, 2019

By Johan PEERS, François DUMORTIER

Today, solutions to optimize Capital Expenditure (CAPEX) & Operational Expenditure (OPEX) for small capacity Cold Rolling Mills (CRM) as well as for high capacity CRM are available, as extensively described by various Original Equipment Manufacturers (OEMs) & steel makers. A suitable solution for small capacity CRM is to start with a single stand reversing mill (up to 400 ktpy, depending on product mix), which can then be expanded into a twin stand mill (up to 900 ktpy, depending on product mix). The main drawbacks in conventional practice are the off-gauge length in single stand set-up and the long downtime of the mill during the erection of the second stand. For higher productions CRM, it is common practice to directly select a new Pickling Line Tandem Cold Mill (PLTCM), with a high CAPEX. Is there an in-between solution that would allow to start with limited output and CAPEX, without jeopardizing the ultimate expansion goal (1.2 to 2 mtpy), for which PLTCM is the best techno-economical choice? In the absence of a solution, JOHN COCKERILL developed an integrated solution that limits the CAPEX in the first phase of development, without crippling affecting future endeavors through an easy and economically sustainable expansion into a PLTCM, without long production downtime. The solution consists of first installing a twin stand mill, expandable into a tandem mill thanks to a smart design of the line. It is therefore possible to limit the production to 900 ktpy in the first phase of the project and then convert the mill into PLTCM in the second phase to increase the production from 1.2 to 2 mtpy, depending on the market trends and financial capabilities. In summary, JOHN COCKERILL has developed a smart new layout in reversing phase combined with a brand new rolling strategy to optimize productivity and limit off-gauge, compared to conventional solutions (patents pending). In addition the layout enables an easy conversion to tandem mill without high over investments, which is more sustainable financially than the initial purchase of a PLTCM. Long downtimes to allow for capacity extension, detrimental to this phase-by-phase approach, are also avoided. Technical and process description of the new layouts and rolling strategies, together with CAPEX & OPEX descriptions of the phases are detailed in this paper.

Oct 1, 2019

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Lorenzo Bacchetti

Automatic yards with ad-hoc WMS (Warehouse management software), are the key for a modern and efficient warehousing which can face today logistic challenges. WMS boosts the traceability of material while optimizing the storage space. The operations in the yard are safer and logically organized according to algorithms that are specifically adjusted case by case. WMS can easily handle multi-cranes yard avoiding conflicts and increasing accuracy of positioning with decreased number of movements. The synergy of automatic cranes and WMS reduces bottlenecks and speeds up the preparation of deliveries with an overall improvement of warehousing and shipping scheduling.

Oct 1, 2019

By Sebastien Maillard, Stephane Georges, Thomas Vallee, Stanislas Mauuary

Steel strip manufacturing ever reinvents proposing new grades, requiring to tackle technical limitations of production systems. Primetals Technologies breaks through strip welding by expanding the welder LW21L “Asolid” technology used on low gauges for high-end market such as automotive CAL/CGL. Addressing the usual drawbacks in maintenance, operation and safety of current welding system based on mechanical cutting and CO2 laser welding, the newly developped LW21H “Asolid” technology processes thicker strips up to 7 mm with solid-state laser cutting and welding. This new welder is brought to reality through a scale 1:1 pilot developed, manufactured and tested in Primetals Technologies workshop.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz, Thiago Soares Lima, Rafael Kakitani

Materiais de interface térmica (Thermal Interface Materials - TIMs) são responsáveis pela troca térmica entre a fonte geradora de calor do processador integrado e o dissipador de calor. Devido ao seu baixo ponto de fusão, boa fluidez e cumprimento com as exigências de regulamentação (Restriction of Hazardous Substances - RoHS), ligas à base de bismuto têm sido investigadas para aplicação como TIMs de alta performance. Neste contexto, a análise das propriedades dessas ligas em função de parâmetros microestruturais torna-se, portanto, de elevado interesse científico e tecnológico para o setor eletrônico. Assim, este trabalho tem como objetivo desenvolver correlações entre propriedades de resistência à tração e a microestrutura da liga Bi-0,28%Ni solidificada sob um intervalo de taxas de resfriamento usualmente obtido em processos industriais. Por meio de microscopias óptica e eletrônica de varredura foi observada uma morfologia tipicamente eutética lamelar, composta por lamelas ricas em bismuto com o intermetálico Bi3Ni nos contornos. Os espaçamentos lamelares (λL) foram, então, correlacionados com os parâmetros térmicos de solidificação, sendo propostas leis experimentais de crescimento microestrutural. Ao fim, observou-se que, para λL < 101 μm, equações do tipo Hall-Petch caracterizam a variação do limite de resistência à tração e do limite de escoamento.

Oct 1, 2019

By Dagoberto Brandão Santos, Marcus Vinícius Pereira Arruda, Fernando de Souza Costa, Túlio Magno Fuzessy de Melo

The development of advanced high strength steels (AHSS) is motivated by the automotive industry demands for higher strength steels with better formability and stretch-flangeability to avoid fractures during parts forming. In response to this, the new steel grades must have special microstructures in terms of constitution, morphology, distribution and hardness, which are strongly dependent on the chemical composition of the steel sheet and its processing, especially in the continuous annealing stage, in the case of cold rolled sheets. In this study the influence of the annealing heating rate and intercritical temperature (IT) on the microstructural evolution and the final hole expansion ratio of a cold rolled 980 MPa AHSS grade was evaluated. The annealing process was simulated using a Dilatometer and a Gleeble machine, and the microstructures were characterized using scanning electron microscopy, electron backscattered diffraction (EBSD) and nanohardness measurements. The increase of heating rate resulted in an overlap between ferrite recrystallization and austenite formation, changing the austenite morphology from a random to a fibrous distribution, while a higher IT resulted in more homogeneous microstructures and higher hole expansion ratios. This microestructural homogeneity, confirmed by nanohardness measurements, suggested that the difference in hardness between ferrite and the second phase affects the micro-void formation and crack propagation during the hole expansion test.

Oct 1, 2019

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Márcia M. S. M. Pereira, Hervé Tavernier, Gérson T. Ferreira, Caio Nogueira Araujo Diniz, Fabio Luiz Lourenço, Wagner C. Moreira, Vinicius Cunha Aranda

Pós fluxantes desempenham um papel significativo na qualidade do aço durante o processo de lingotamento contínuo. Os pós fluxantes são escórias sintéticas usadas para lubrificar o molde durante o lingotamento contínuo do aço. Para que isso ocorra, o fluxante deve apresentar as seguintes funções: isolamento químico e térmico do aço, absorção de inclusões não metálicas do aço, lubrificação do molde e controle da transferência de calor entre o aço e o molde. O desempenho de cada função está relacionado às propriedades químicas e físicas do pó fluxante, que são dependentes de sua composição química e sua composição mineral, devido a sua relação com a taxa de fusão do material. A fim de garantir uma produção eficiente e de alta qualidade durante o lingotamento de um aço ultra baixo carbono, os pós fluxantes A e B foram investigados de acordo com diferentes propriedades físico-químicas. Diversos experimentos laboratoriais foram realizados para comparar o desempenho dos materiais A e B, visando à diminuição de captura da escória pelo aço no molde: avaliação do comportamento de fusão e fluidez, composição química e viscosidade. As temperaturas de processo foram avaliadas através de testes estatísticos, visando caracterizar o fluxo de calor e o trabalho de fricção durante lingotamento. Os testes industriais preliminares, realizados na Ternium Brasil, foram conduzidos com o objetivo de analisar o comportamento do pó fluxante durante a operação de lingotamento contínuo em relação a alguns aspectos operacionais e fornecer informações sobre sua influência na qualidade superficial do aço. Os resultados mostraram que, aumentando a viscosidade do fluxante, o consumo de pó tornou-se menor, levando a um maior trabalho de fricção e menor fluxo de calor no molde. No entanto, o comportamento da camada de escória mostrou que, apesar do aumento da força de atrito no molde, a espessura da escória foi adequada e não houve relatos de defeitos superficiais durante o uso do material fluxante de maior viscosidade.

Oct 1, 2019

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019

By Mario SINNAEVE, Olivier LEMAIRE, Gisèle WALMAG, Sébastien FLAMENT

Many hot rolling mills worldwide face nowadays bonding zone fatigue problems before reaching scrap diameter of the work rolls. This phenomenon is nowadays known to occur in reversing roughing mills both in stainless steel and in carbon steel rolling. The phenomenon can be explained through longer rolling campaigns, inadequate backup or work roll maintenance, harder steel grades or increased throughput by reduced amount of passes to achieve the same thickness. In order to help users in optimizing the roll use, we developed a numerical tool to evaluate and optimize roll maintenance. This paper will review the influence of roll geometries on stresses generated at the roll surface but also at the bonding zone. We will also show how roll geometries can decrease contact fatigue damages by modifying crowning and chamfering procedures, shell thickness, material design or campaign length

Oct 1, 2019

By Rafael Valencia-Dongo, Ernesto Ramírez, Julio Tapia

Enfocado en una novedosa metodología de resolución de conflictos basada en la teoría de juegos, este artículo propone estrategias para generar un equilibrio estable entre empresa, Estado y comunidad. Tras evaluar la tipología y características de la conflictividad socioambiental por acción de líderes opositores a la inversión, se desarrolla un marco de resolución de conflictos a través de lo que se denominan pactos de contrapeso, que cubren los ámbitos de comunicación, gestión sociopolítica y fidelización del trabajador minero. Estos pactos permiten cambiar la percepción, incentivos y acciones de los actores, lo que incluye la acción de terceros legítimos.

Sep 30, 2019

By Tung Vu, Michael Harrington

"The Regional Connector project is a complex subway light-rail project that runs through the heart of downtown Los Angeles, CA. The design-build contract was awarded in April 2014 to the Regional Connector Constructors (RCC), a joint venture between Skanska USA Civil West California District Inc. and Traylor Brothers Inc., and their designer team consisting of Hatch Mott McDonald (HMM) and subconsultants. The project broke ground on Sept. 30, 2014 and is expected to be completed in winter 2021-2022. The main components of the project consist of 6.4-m (21-ft) diameter twin-bored tunnels, three crosspassages, a 87-m (287-ft) long crossover SEM cavern, three new underground stations, and cut-and-cover tunnels along South Flower, Alameda and 1st Streets. The project map is shown in Fig. 1. The design and construction challenges associated with each of these main components are discussed in the following sections.Project designTunnels. The Regional Connector tunnels are located primarily within the Fernando formation consisting predominantly of extremely weak to very weak, massive, clayey siltstone. About 305 m (1,000 ft) of tunnels on the eastern end are in alluvium and mixed face of Fernando formation and alluvium. The tightest curve of the tunnel alignment is 178 m (583 ft) in radius. The tunnels were designed with a reinforced precast concrete tunnel lining (PCTL) to be used with an earth balance pressurized (EPB) tunnel boring machine. The PCTL ring is 5.5 m (18 ft-10 in.) inside diameter, 27 cm (10.5 ft) thick, 1.5 m (5 ft) long, and consists of five segments and a key. The segments were designed with 6,500 psi concrete, 80 ksi yield strength wire rebar, convex joint surfaces to enhance seismic performance, and a dosage of 1.7 lbs polypropylene microfibers per cubic yard of concrete for fire resistance. The rings are designed with a right ring and left ring pattern and a taper of 3.8 cm (1.5 ft) to allow for alignment curve negotiation. Figure 2 shows typical sections of the PCTL. The structural lining design was modeled using FLAC 3D. Four consecutive rings were modeled with 32 dowel connection. Loading considered in the lining design includes temporary ground load during excavation, long-term ground loads, seismic loads and train loads. The seismic loads on the PCTL were simulated with the racking deformation applied at vertical boundaries of the model. Due to variation of geologic condition along the tunnel alignment and different surcharge requirements, three different types of reinforcement (typical, heavy and extra heavy) were designed. The typical type PCTL was required in Fernando formation, the heavy type was required in alluvium or mixed-face condition, and the extra heavy type was required in alluvium and underneath the Japanese Village Plaza where a surcharge of 1,000 psf was required."

Sep 1, 2019

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By Gleason

"From June 16 to 19, more than 1,400 tunneling and underground construction professionals gathered in Chicago, IL for the bienial Rapid Excavation and Tunneling Conference (RETC). There, they were greeted by a full technical program and an exciting exhibit hall that provided a comprehensive look at the world’s bustling tunneling and underground construction industry.The successful conference was a reflection of the industry itself, which is to say, busy. As much of the world has begun to focus on creating a cleaner and greener environment, the global tunneling industry has seen an uptick in infrastructure projects move from design-build to construction phase. With a global shift away from the use of fossil fuels, major cities around the world are looking to increase public transportation options, which leads to the need for more transportation tunnels. And as urban populations continue to grow, the need for clean water calls for more tunnels, and as urban footprints continue to expand, the need to increase and update combined sewage overflow tunnel grows with them.During two and a half days, more than 20 sessions covering all of these topics were presented at the Hyatt Regency in Chicago, many to packed rooms in which every seat was taken and people were standing along the side and back walls.RETC is a biennial conference and one of the largest in the North America for the tunneling and underground construction industries. As such, it hosts a robust exhibit floor. This year 172 vendors occupied 205 booth spaces. The exhibit included everything from tunnel boring machine manufacturers, like Robbins and Herrenknecht, to the companies that supply all kinds of parts and services to the industry."

Sep 1, 2019

By H. Gerry Stephenson, Devin Castendyk

"One of the most important environmental issues associated with contemporary openpit mining is the closure of mine pit lakes, and the perpetual legacy these lakes can potentially generate. Ideally, successful pit lake closure includes the following:• The water quality within the pit lake, plus surface water and ground water discharging from the pit lake, meets premining or other acceptable water quality conditions of the receiving environment. • The termination of all active treatment processes.• The return of the pit lake to the government for long-term care and maintenance.• The release of the mining company from all future liabilities associated with the pit lake.• The return of the environmental bond to the mining company.• The reuse of the pit lake for some post-closure, beneficial purpose.The achievement of these goals is known as walk away pit lake closure.Peer-reviewed publications of successful walk away, pit lake closure provide mining companies with the ability to address public concerns regarding the safety of pit lakes which commonly occur during the permitting, operations, and closure phases of mining. To date, most published work on walk away, pit lake closure work has occurred in the coal mining sector in Germany and Australia (McCullough et al., 2009; Jones and McCullough, 2011; Kumar et al., 2013; Schultz et al., 2013). In North America, examples of walk away, pit lake closure are not widely discussed in the literature despite there being excellent examples from the coal mining sector in Alberta, Canada (e.g. Pleasure Island, Black Diamond, East Pit, Sphynx, Robb, Lovette, Siltstone and Sterling), and from the iron mining sector in Minnesota in the United States (e.g. Portsmouth Lake, see MNDNR, 2018). Although seldom included in discussions of pit lakes from the metal and coal mining sectors, the aggregate and fabricated-stone mining sectors also produce pit lakes, and there are numerous examples throughout North America where these pit lakes have been successfully closed and transformed into post-mining resources (Vandenberg, 2018; Crossman, 2019). The difficulty of finding these good examples in the literature makes it challenging for companies to respond to public and regulatory questions regarding pit lake closure and reuse. As such, there is a pressing need to document the motivations and approaches used in examples of successful, walk away, pit lake closure in North America so that the mining industry, at large, can learn from these examples and can better address public concerns."

Aug 1, 2019

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By L. Makua, K. Langa, Ndlovu. S., C. Saguru

"Global demand for the three platinum group metals (PGMs) Pt, Pd, and Rh has been steadily growing due to their widespread use in emission control, industrial catalysis, and numerous other applications. The primary supply of PGMs is currently the mining industry. However, legislative, operational, and environmental challenges faced by many mining operations result in erratic supply patterns and deficits for these three metals. Naturally, recycling scrap material to recover Pt, Pd, and Rh has therefore aroused research interest in the scientific and engineering communities. Given that the majority of the global demand for these three metals is driven by emission control devices, autocatalytic converters are therefore a significant source of already processed and beneficiated PGMs for recycling.Although pyrometallurgical processes dominate the recycling industry, hydrometallurgical processes may offer certain advantages, chief among these being lower emissions and reduced energy consumption. In this investigation, scrap converter material was leached in acidic chloride media and the leach liquor subjected to solvent extraction and cloud point extraction (CPE) to recover the PGMs. The recoveries for Pt and Pd using Alamine 308® dissolved in kerosene with decanol as a modifier were 95% and 81%, respectively. The maximum recoveries using CPE after complexation with 2-mercaptobenzothiazole (2-MBT) in the presence of Triton X-100 and tin (II) chloride dihydrate as a reductant were 97% for Pd, 96% for Pt, and 91% for Rh. This demonstrates that CPE, although relatively new, may have some potential as a breakthrough PGM recovery technology. IntroductionPlatinum group metals (PGMs) have found a wide variety of applications in different industries due to their chemical, catalytic, and physical properties. PGMs are essential in automobile emission abatement, petroleum refining, and the pharmaceutical and electrical industries (Carabias-Martinez et al., 2000). However, the abundance of PGMs in the Earth’s crust is low and their primary sources are fast depleting (Crundwell et al., 2011).The high demand for PGMs, together with social, economic, environmental, and political aspects related to their production, has led to concerns about their future supply. This has resulted in renewed interest in recycling end-of-life material. PGM supply from recycling has doubled over the last decade, and currently contributes 22% to global supply (Johnson Matthey, 2016). This is in part due to the environmental, social, and operational challenges associated with mining of PGMs. For example, labour unrest, energy cuts, declining commodity prices, and declining ore grades have collectively made the mining landscape economically challenging (KPMG, 2015). On the other hand, the high content of PGMs in secondary sources makes their recovery from the increasing quantities of waste products important from a resource conservation viewpoint. Moreover, PGMs obtained through recycling have been demonstrated to have a 1% environmental cost from a life-cycle perspective, whereas PGMs obtained from mining contribute the remaining 99% of environmental cost (Bossi and Gediga, 2017). Sustainable resource recovery and the economic incentive of recycling have therefore been major drivers to justify investment in PGM recycling. The autocatalytic converter industry accounts for about 70% of the global consumption of these metals (Johnson Matthey, 2016) and therefore recycling spent converters has become a major source of Pt, Pd, and Rh (Figure 1)."

May 1, 2019

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019