Search Documents

By G. A. Sutton

"At the San Manuel mine (Arizona, USA), in-situ copper leaching of a copper porphyry deposit was carried out from 1986 to 1999 during underground and open-pit mining. In 1993–1994, well¬field testing of the supergene zone, composed primarily of chrysocolla and copper-rich clay minerals, led to estimates that 52% of the acid-soluble copper (ASCu) could be recovered during in-situ leaching; however, the actual recovery from zone 6, which had the longest leach history, was approximately 42%. Comparing drillcore assay data from holes drilled before and after leaching also indicated an approximate recovery of 42%. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to several factors, including difficulty maintaining fluid saturation, channelling effects, and gypsum precipitation. ¦ KEYWORDS Copper oxides, in-situ leaching, Modelling, Porphyry, Solvent extraction and electrowinning (SXEW), Well-to-well RÉSUMÉ À la mine San Manuel (Arizona, États-Unis), on a procédé de 1986 à 1999 à la lixiviation in-situ de cuivre d’un gisement porphyre cuprifère pendant l’exploitation minière souterraine et à ciel ouvert. En 1993 et 1994, des essais effectués dans des champs de captage de la zone supergène, composée principalement de chrysocolle et de minéraux argileux cuprifères, ont abouti à des estimations selon lesquelles on peut récupérer 52 % de cuivre soluble dans l’acide (ASCu) pendant la lixiviation in-situ ; toutefois, la récupération réelle dans la zone 6, qui affiche l’histoire la plus ancienne en matière de lixiviation, était d’environ 42 %. La comparaison des données d’analyses de forage obtenues à partir de trous forés avant et après la lixiviation indiquait également une récupération approximative de 42 %. La différence entre la récupération prévue (52 %) et réelle (42 %) réside probablement dans plusieurs facteurs, notamment la difficulté à maintenir la saturation des fluides, les effets de canalisation et la précipitation du gypse. ¦ MOTS CLÉS d’un puits à l’autre, extraction par solvant et extraction électrolytique (SXEW), lixiviation in-situ, modélisation, oxydes de cuivre, porphyreINTRODUCTION in-situ copper leaching at the San Manuel mine, Arizona, USA (Figure 1), began in 1986. It was recognized that some of the copper oxide resource was not economically recoverable by conventional open-pit and heap leach methods using solvent extraction and electrowinning (SXEW) and a high stripping ratio would be required to access part of the resource. At the time, in-situ leaching was becoming popular in the uranium industry, but the approach was virtually unknown in the copper industry, especially at a large scale."

Jan 1, 2019

By Tyler J. Irving

"In June, 2018 Lalor Mine experienced a catastrophic blade failure of its No. 2 main exhaust fan. Over the following weeks several key changes were made to the auxiliary ventilation system to allow for continued production while the exhaust fans were repaired. Issues encountered during the period of reduced ventilation, and how they were addressed, are analyzed. The suspected causes of the exhaust fan blade failure and how risk was mitigated during the reconstruction are discussed. Key findings and lessons learned are summarized.INTRODUCTIONLalor Mine, owned and operated by Hudbay is an underground zinc, gold, and copper mine located in northern Manitoba. The mine workings extend to a depth of 1090 metres below surface and is ventilated using a push-pull system. The mine exhausts through the main exhaust raise; equipped with two, 2,500 HP fans and upcasts through a portal located at the neighboring mine, Chisel North. Air is supplied to Lalor Mine through four intake fans: The Production Shaft Downcast (two, 250 HP), Lalor Downcast (one, 400 HP), and Chisel Downcast (one, 600 HP) fans (Figure 1). In June 2018, Lalor was scheduled to produce approximately 4,000 tpd.On June 20, 2018 at 2:52 pm Lalor Mine experienced a fault on the Variable Frequency Drive (VFD) for Exhaust Fan No. 1. Time would be needed to complete the necessary repairs. The No. 2 exhaust fan was ramped up from 525 rpm to 800 rpm, 90% of its capacity, in order to maintain underground ventilation. At 4:46 pm, approximately two hours after the rpm was increased, exhaust fan No. 2 experienced a catastrophic blade failure. The forces from the blade failure resulted in the top half of the fan housing being thrown 50 metres from where it was installed; with several large sections of fan blade being thrown further (Figure 2)."

Jan 1, 2019

"The ventilation-related risks from mines with elemental sulphur include dust explosions, spontaneous combustion with emission of heat and toxic sulphur dioxide or hydrogen sulphide gases, reactions with nitrates, corrosion, acid water, and pyrophoric reactions with naked iron or other metals. Elemental sulphur will form explosive mixtures in air at lower dust concentrations and at lower ignition temperatures than coal or sulphide dusts. Potential controls include primary ventilation circuit design, control of dust deposition and static discharges, enclosing steel surfaces, inert stone dusting, FRAS ducting, humidifying the air, alternate stench gas, self-contained self-rescuers with goggles, careful siting of underground infrastructure, controls on explosives formulations and procedures, mining method selection, controls on surface temperatures and protection of equipment, careful materials selection for ventilation seals and changes to worker clothing and training.INTRODUCTIONSulphur (“Brimstone” in biblical times) is one of the world’s most important industrial feedstocks and is used in a wide range of chemical processes and industries. Until the early 20th Century, most of the world’s production of sulphur came from ‘conventional’ underground mines in Sicily (Demetra produzioni, 2006; Bellia, 2006). This was a hazardous activity. The Frasch solution mining process replaced traditional underground mining of sulphur until the late 20th Century. Most of the world’s production of elemental sulphur is now as a by-product from sour gas produced in petroleum refineries and natural gas installations (Anon, 1993). As such, there is considerable experience in understanding and managing the hazards of elemental sulphur in chemical plants and surface transport.Whilst rare, underground mines with high elemental sulphur contents (as a gangue mineral) create an unusual range of mine design and operational issues, including many ventilation-related ones. The key hazards from elemental sulphur include: primary and secondary elemental sulphur dust explosions, fires and burning (with emission of heat and sulphur dioxide or hydrogen sulphide gas), reactions with nitrates used in explosives, corrosion of steel and other metals, generation of acid water (especially at higher water temperatures), and pyrophoric reactions with naked iron (e.g., ground support, ladderways or underground fixed plant) or other metals including silver and copper (e.g., used in electrical components and equipment)."

Jan 1, 2019

By M. Tokoglu

Accurate estimation of resources is one of the major challenges in mineral project evaluation. Contemporary mineral resource estimation practice calls for contribution from several disciplines and execution of several interdependent tasks. 3D estimation domain modelling is obviously one of the most essential components of such a substantial process which forms the basis of this research. The study constitutes a comparative analysis of four major domain modelling techniques; (i) explicit modelling, (ii) implicit modelling, (iii) indicator kriging, and (iv) conditional simulation. It involves comparison of outcomes for alternative scenarios to assess the implications of the modelling decision on resource estimates of a polymetallic massive sulfide deposit located in western Turkey. Thus, identical grade estimation method and parameters are considered to identify the discrepancies arising only from the choice of the domain modelling approach and underlying assumptions. Economic implications are demonstrated in the form of range of outcomes for the extends of the ultimate pit, ore tonnages (min:37.0 Mt, max: 46.7Mt), waste tonnages (min:201.2 Mt, max: 251.2 Mt), stripping ratios (min:5.18, max: 5.71), and total pit values (min: $1.05B, max: $1.45B). Examination of solid models as well as cross-sections revealed that major discrepancies are observed beyond outlying drillholes. Therefore, it has been proposed that assumptions regarding extrapolation distance is the main source of mentioned dissimilarities. Key words: Domain modelling, explicit modelling, implicit modelling, indicator kriging, conditional simulation INTRODUCTION Resource estimation is apparently a challenging process calling for extensive expertise and input from several sources, each of which introducing its related uncertainties. In the last decades, substantial role of quantitative analysis of several forms of risk and uncertainty in evaluating projects’ upside potential and downside risks has been realized. Studies indicated that mining companies have been severely impacted because of not meeting project expectations. As noted by Vallee (2000) “… in the first year of operation after start-up, 60% of mines surveyed had an average rate of production less than 70% of designed capacity”. Several other studies on mining projects also revealed that uncertainties related with the resource model are one of the major contributors of mentioned shortfalls. In this perspective, quantification of uncertainties associated with each component of estimation process is critical. 3D estimation domain models capturing major mineralization controls are the fundamental components of contemporary mineral resource estimation. Domain models are key guiding tools for estimation and are products of a complex process involving many unknowns and assumptions. There exists a number of 3D modelling alternatives which are distinct with respect to complexity, time and effort involved. Acknowledging potential influences on downstream mining practices and relavent economic implications, risks and uncertainties associated with 3D domain modelling are critical yet poorly studied aspects.

Jan 1, 2019

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By G. Q. Zhou, H. C. Liang, X. D. Zhao

"This study describes the strain behavior in vertical shaft lining (VSL) embedded in thick soil deposits and its application in assessment of concrete deterioration. The observed strain in VSL continuously decreased companied by a sinusoidal fluctuation due to the influences derived from negative skin friction (NSF) and temperature. The increase in strain increment between peak and trough at each year and compressive strain level as the servicing time continued and VSL depth increased implies that the concrete strength was attenuated, and this attenuation was significantly dependent on the existing compressive strain level in VSL. The reliability of the proposed approach was validated by Schmidt Hammer Technique (SHT) – based concrete strength, and is applicable in concrete assessment and then fracturing prediction of VLSs in thick soil deposits.Concrete strength, Field monitoring, Strain behavior, Vertical shaft liningINTRODUCTIONOver 100 VSLs in Southeastern China subjected to an unpredictable fracturing as shown in Figure1, and there are over 1,000 VSLs embedded in thick alluvium su?ering from challenges of damaging and potential fracturing (Cheng, Yang, Zhou, Li, & Hu, 1993; Zhou, Cui, Lv, Huang, & Chen, 1999; Li & Li,2005). Therefore, a reliable assessment of these VSLs is significant to the normal servicing of mine shafts and the recycle of underground space when these mine shafts were closed.The continuous increasing of NSF induced by the drainage of water–saturated deposits well interpreted such extensive fracturing phenomenon, and it is universally regarded as the governing indicator to determine the VSL stabilization (Cheng et al., 1993; Zhou et al., 1999). Based on this recognition, the fracturing prediction and VSL strengthening according to the field monitoring on hydrogeological characteristics, servicing environments, and mechanical behaviors of VSL were carried out (Zhao, Zhou, Zhong, Zhu, & Liang, 2009; Liang et al., 2009; Xie, Lv, & Wu, 2014). As known, the compressive strain level in VSL and the in–situ strength of VSL concrete were the main factors to perform such fracturing prediction. However, the existing studies in literatures were limited to the strain accumulating or releasing behaviors (Zhao, Zhou, Zhao, Kuang, & Hu, 2017), and lack of considering the VSL concrete strength and its attenuation. In this reported study, the in–situ monitoring data on the strain in typical VSLs and the VSL elevations between 2004 and 2014 were initially analyzed. Then, an observed strain behaviors–based approach was developed to quantitatively evaluate the VSL concrete deterioration."

Jan 1, 2019

By Kevin Andrews, Terry Hamric, Scott Nelson

"Mining conditions in underground coal mines are dictated by the environment in which the coal seams were geologically deposited. Depositional features can change rapidly, significantly affecting mining conditions. Mine geologists understand factors affecting mining conditions, predict future conditions, and provide guidance to mine management. A case study demonstrates how a mine in Appalachia merged an understanding of depositional environments with mining conditions and drilling data to make informed decisions as the mine encountered geologic anomalies. The assessment included drilling, mapping of geologic hazards and mine productivity, and creation of a conceptual depositional model. Metallurgical coal quality and clean tons per foot served as incentives for continued advance. Mining in the south was historically favorable, with good production and advance rates. As mining advanced north, changing geologic conditions caused the upper seam split to abruptly disappear. The mine ramped down into the lower seam split. Mining in the north area encountered unfavorable conditions, including transition roof, “horsebacks,” sandstone intrusions, roof rolls, and bony floor, resulting in low rates of mining advance. The mine geologist characterized the features and created a predictive model for future mining. Most of the adverse conditions were attributed to the coal in the north being part of an incised, transgressive valley fill environment, as compared to the favorable conditions in the south resulting from a floodplain depositional environment. Geologic conditions, low productivity, and unfavorable future predicted conditions in the north ultimately resulted in mine closure and reallocation of resources to a new mine with better forecasted conditions.INTRODUCTIONThe role of a geologist in assisting coal mining operations to understand and predict the impact of varying geological factors on mining productivity is a critical one, especially when management decisions must be made about the future prospects of a mine operating in difficult conditions. Chase, Newman, and Rusnak (2006) provide a very thorough discussion of the evolution of the role of the coal mine geologist and emphasizes the importance of understanding geology with regard to mine management decisions. Using actual mining performance data to determine which geologic factors are the most critical for mining is a powerful tool for making informed mine management decisions. For example, Nelson, Mullennex, and Miller (1988) provide a case study of analyzing the geologic factors impacting productivity of a Kentucky longwall mine to predict future mining conditions for the operation. In that case, the difficult geologic factors for longwall mining were prevalent across much of the remaining permit area and, in response, mine management converted the operation from a longwall operation to a continuous miner (CM) operation to better adapt to the geology. In another example, Keim and Miller (1999) evaluated geologic conditions impacting a West Virginia longwall mine. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed. Numerous examples of advanced Geologic Hazard Mapping (GHM) methodologies have come from government agencies and academia. For example, development of the Coal Mine Roof Rating (CMRR) system (Molinda and Mark, 1994) provided a standard means for geologists and engineers to communicate quantitatively with regard to mine roof conditions, and the introduction of the Stability Mapping System (SMS) provided an efficient means for analyzing numerous factors affecting coal mine stability (Wang and Heasley, 2005)."

Jan 1, 2019

By K. Mohamed, G. Rashed

A conventional mechanical anchor bolt consists of a smooth bar threaded at the anchor end, with a conical wedge, and a mechanical shell anchor. When the smooth bar is torqued, the conical wedge pushes the shell anchor against the borehole wall. Coal mines use mechanical bolts in addition to other types of bolts to control the deformation and stabilize the yielded coal ribs. Limited research has been conducted to understand how a mechanical anchor performs in a coal rib. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted the study described in this paper to define the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of a mechanical rib bolt. Based on the strength of the coal seam and the conditions of the coal mines, the bolts were installed at different amounts of torque. A typical tri-linear load-deformation response was obtained from these tests. It was found that the anchorage capacity depends on the coal strength, and the anchorage stiffness depends on the installation torque. The outcome of this research provides essential data for rib support design. INTRODUCTION Rib falls are a serious hazard in underground coal mines. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Although resin bolts has been used increasingly in the last few years to control coal ribs, mechanical bolting (mainly expansion-shell bolts) is still used in many underground coal mines. Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 79% of the mines determine their rib support requirement based on the depth, mining height, and the loading conditions, of which 35% use the conventional mechanical bolts. Conventional mechanical bolts are preferable for rib support because they do not require the miners to be too close to the rib during rib bolting. Hence, using the conventional mechanical rib bolts can reduce the risk of injuries and fatalities during the installation process. The mechanical bolt or the point-anchored bolt is the oldest type of rock bolt that is still in use today. The point-anchored bolt is a tensioned bolt anchored down the hole with a mechanical expansion shell or a grouted medium (Peng and Tang, 1984). Figure 1 shows the components of the mechanical anchor bolt. The mechanical anchor bolt consists of a plug, a shell anchor, a headed smooth bar with the top end threaded, a bearing plate, a hardened washer, and sometimes a friction-reducing washer. The shell anchor can be either standard or bail type. The shell of the standard type is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the smooth bar is generally 5/8 in for the #5 bolt or 6/8 in for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the wedge down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall.

Jan 1, 2019

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By C. K. Arthur, N. K. Dumakor-Dupey, B. A. Kansake, F. A. Kaba

Autonomous mining systems have been deployed for improving mine performance. However, there is a fear of job losses. Adoption of autonomous systems is envisaged to be resisted by major stakeholders in Ghana due to high illiteracy and unemployment. This paper assesses the preparedness of Ghanaian mining stakeholders for the adoption of autonomous systems to Ghana’s surface mining industry. Closed and open-ended questionnaires were administered to mine stakeholders. Respondents generally expressed unwillingness to accept autonomous systems into Ghanaian mines due to fear of increased unemployment. We propose setting up a mining education fund (MEF) for training stakeholders in autonomous mining systems. INTRODUCTION Mining contributes enormously to the sustenance and growth of global and national economies through the provision of raw materials, employment, revenues and foreign exchange (Carvalho, 2017; ICMM, 2017; Cordes et al., 2016; Solomon et al., 2008; Walser, 2000). The International Council on Mining & Metals (ICMM, 2014) reported that globally, formal mining employs approximately 2.5 million people. Many resource-rich countries, especially the developing ones, have experienced strong socioeconomic growth propelled by the discovery and extraction of valuable minerals. McMahon and Moreira (2014) reported a positive linkage between mining and sustainable development. They revealed that averagely, resource-rich countries have improved Human Development Index (HDI) scores than countries without mineral resources. Mining remains a crucial industry in Ghana’s economic development (Bermúdez-Lugo, 2016; Amponsah-Tawiah and Dartey-Baah, 2011). Over the years, mining has contributed significantly to the gross domestic product (GDP) of Ghana. In 2013, mining accounted for 1.7% of Ghana’s GDP and about 19% of government revenues (Ghana Chamber of Mines, 2015). The Ghana Chamber of Mines also reported that mining contributed over 50% of foreign direct investment, 37% of export earnings and 1.1% of direct employment revenues. The US Department of Energy (DOE) estimates that 65% of coal, 92% of metals and 96% of industrial minerals are mined using surface mining methods (DOE, 2007). Generally, mining is a capital-intensive venture, with high operating cost, hence there is a constant demand for mining companies to seek efficient cost reduction and production maximization strategies. One strategy being pursued keenly is automation, which is noted to improve productivity, and worker safety at minimal cost. According to Parreira (2013), mining automation involves direct teleoperation whereby workers remotely control the mining process using computers from a control room.

Jan 1, 2019

By W. Kempson

"Mining Companies have producing assets in increasingly diverse portions of the world. It is not uncommon that the owner, the design team, the mine contractors and the operators are all based in different countries. While these assets are always subject to the regulatory requirement of those countries there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical items such as tailings dams, vertical shaft systems and autonomous vehicles to highlight a few. The work currently being completed in ISO ensures these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. This paper will discuss the benefits of the international standards, the structure of the teams and working groups who are generating these standards as well as the process by which the standards are generated. This will allow insight into the creation of the standard and will aim to demonstrate the “neutral” and technically strong manner in which the generation of these standards is achieved. In addition, the paper will discuss the standards which have been produced in the last five years as well as the current standards which are in place. The finale will discuss upcoming work and the timelines in which it is anticipated these will be completed. INTRODUCTION Mining Companies have producing assets in increasingly diverse portions of the world. While these assets are always subject to the regulatory requirement of those countries, there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical areas such as vertical shaft systems, tailings dams and autonomous vehicles to highlight a couple. The work currently being completed in the International Organization for Standardization (ISO) ensure these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. The ISO/TC 82 – Mining was founded in 1955. This was an active committee until it was thought that the standards at the time were adequate and the Technical Committee was put on “Care and Maintenance”. In 2012 countries lobbied ISO to pull this committee from dormancy and restart it, this happened in in the same year."

Jan 1, 2019

By Y. M. Shneerson, I. V. Fomenko, M. A. Pleshkov, E. A. Ospanov, A. A. Shakhalov, S. S. Naboychenko

Low-grade copper concentrates (with copper content less than 20%) often contain impurities such as arsenic, zinc, lead, mercury, antimony and bismuth. The pyrometallurgical treatment of such concentrates is associated with several problems, which will ultimately affect the cost and the quality of copper cathodes as well as by-products. SRC Hydrometallurgy proposed a complex hydrometallurgical technology which allows the removal of impurities and the enrichment of low-grade copper concentrates to a quality which will be more suitable for pyrometallurgical processing. Laboratory batch tests and pilot plant results for the pressure leaching steps are shown in this paper. The key parameters of the leaching steps were determined and optimized. The quality of possible by-products were also determined. The developed flowsheet includes two pressure leaching steps: pressure oxidation (POX) and hydrothermal alteration (HTA). Both operations are carried out at 170°C with subsequent flotation of POX and HTA residues and recovery of copper, zinc and lead into separate concentrates for further processing. The development of the flowsheet was based on the Balkhash Zinc Plant (Balkhash, Kazakhstan), which had been non-operational since 2009. The developed flowsheet for processing of low-grade concentrates will utilize 80% of the existing equipment of the Balkhash Zinc Plant, thus leading to a significant reduction in required capital expenditure. INTRODUCTION As the age of copper mining operations advance, copper grades continue to diminish and impurity levels increase. Therefore, copper producers are forced to look for new innovative hydrometallurgical technologies which are able to handle low-grade raw materials and solve problems associated with impurities in an economically justifiable way. New technologies allow to extract valuable components selectively and to process low-grade concentrates which had previously been marked as non-technological and economically unviable. Hydrometallurgical technologies for processing of copper-containing materials can be divided into two main categories: chloride and sulfate (atmospheric, autoclave and bacterial) based technologies. Since the 1970s, many autoclave techniques for the processing of copper-containing materials have been developed and implemented (Naboichenko, 2002; Dreisinger, 2005; Habashi, 2009; Shneerson, 2011). The mineralogical composition of the ore (or concentrates), geographical location of the deposit, distance from industrial areas, availability of existing treatment facilities, availability of skilled labor, cost of electricity and cost of neutralization are some of the factors which are usually considered when the appropriate technology is selected (Halbe, 2002).

Jan 1, 2019

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By Pengfei Wang, Guorui Feng, Shufeng Zhang, Yuxia Guo, Tingye Qi, Dian Li

"Based on the geological conditions of the No. 10203 mining face of the Xinyang coal mine, a numerical model of the longwall backfilling face is built using the FLAC3D software to calculate the limit broken length of the key strata. Based on the deformation laws of the immediate roof, the backfilling parameters are determined. Furthermore, the movement laws of the overburden strata with different volume filling rates (0, 40, 60, 100, and 100%) and with different layout forms of the filling strip (under a volume filling rate of 60%) are analyzed. The results of the numerical modeling show that the stress of the two sides of the working face and the deformation of the overlying rock are gradually reduced with the increment of the volume filling ratio. In view of the deformation of the roof strata within the allowable range, a volume filling rate of 60% is selected to simulate and analyze the filling effect under different layout forms of the filling strip. The filling width, stress concentration area, and layout form of the filling strip are the key factors to control the movement of the overlying strata. In addition, the probability integral formula is used to calculate and predict the ground subsidence on the filling area, which confirmed that the backfilling mining method is fully applicable in the Xinyang coal mine. The results of this study provide a certain theoretical basis for the determination of the filling process in the field.INTRODUCTIONIn China and other coal producing countries, gob is managed using the caving, filling, supporting, and slowly sinking methods (Zhang, Zhou, and Zhang, 2009). With the continuing development of the concept of green coal mining (Guo, Deng, and Zou, 2004), the filling method, which is safe and environmentally friendly, has been widely used in the field. On one hand, this method could reduce waste rock and other waste discharge. On the other hand, it could effectively slow the surface subsidence. Recently, strip-filling mining mostly adapted the arrangement of the strip backfill with equal intervals and widths (Xie et al., 2004), but the reasonability of this arrangement should be discussed. To arrange the intervals and width of the strip-filling body reasonably, Feng et al. (2019) put forward the “constructional backfill mining (CBM)” concept. The CBM is a type of backfill mining with low backfill rate, strong structural stability, and good backfill effect. The targets of the CBM include the efficient usage of solid waste resources in mining areas to reduce the backfill cost, the improvement of backfill materials and backfill technologies to increase the backfill efficiency, and rational planning of backfill and mining scheme to reuse the underground mining space. The determination of proper width and intervals for the strip-filling body is the main content of the CBM. Strip-filling mining using cemented coal gangue backfilling is the main method to undertake overburden of the overlying strata and to slow down the surface deformation. It also plays an effective role in cost reduction (Xu et al., 2007). This study focuses on proper determination of the strip-filling body parameters according to actual geological conditions by a simulation. It provides an appropriate reference for backfill mining in the Xinyang coal mine."

Jan 1, 2019

By S. W. Henley

"Shaft sinking design is typically driven by what has been successful in the past and the availability of sinking plant. This document considers a project where the sinking design and methodology is unconstrained by conventional thinking and removed from the commonly held belief that a sinking methodology should be developed from available winding plant. Schedule was a key driver for the Project and led to an alternative sinking design that aimed to optimise sinking advance rates by specifying new winders that compliment known sinking plant while providing improved safety, redundancy and flexibility within each part of the sinking cycle. KEYWORDS Consistent, Efficient, Flexible, Improved, Innovative, Optimise, Redundancy, Safety, Schedule INTRODUCTION The project is remotely located in the South Gobi region of Mongolia on a brownfield site and the scope of work included the concurrent blind sinking and concrete lining of two (2) ventilation shafts to an approximate depth of 1,150 m at a finished diameter of 10 m and 11 m respectively. All sinking and lining operations to be completed as in-line activities, (no lining whilst other activities are undertaken). The project was schedule driven with a completion date set for the first quarter (calendar) of 2021 and there were no restrictions imposed on the successful Contractor with respect to their equipment selection. Existing sinking plant already onsite from three previous shaft sinking operations would be made available to the Contractor if required on an as is where is basis Sustained advance rates in excess of 2.4 m per day would be required in order to achieve the completion milestone, therefore the design would have to include contingency and demanded flexibility to account for equipment down time. Previous shafts that had been sunk onsite have utilised a single double drum kibble (bucket) winder (hoist) with a single excavator loading on the shaft floor into a large capacity kibble (bucket). DESIGN Mucking The sinking design centred on the mucking cycle given that this is traditionally the most restrictive part of the sinking cycle and typically accounts for one third of the overall sinking cycle. The Vertical Shaft Mucker (VSM) and/or diesel excavator are commonly used plant for shaft sinking that were under consideration. The use of Cactus Grabs was not considered given the higher risk associated with grab ropes and hoist failures."

Jan 1, 2019

By L. Iacopetti, A. Calderara, M. Perego, P. Perrone, T. Furusawa

De Nora, a global leader in the development, manufacture and sale of all DSA® anodes based on titanium coated with mixed metal oxide (MMO) for electrochemical processes will present key advancements made to Self-Protected Anodes (SPA) for metal electrowinning. (DSA® is a registered trademark of Industrie De Nora S.p.A., Italy). In 2017 pre-commercial demonstration cells were operated in industrial environment. The program’s focus was to fully demonstrate the SPA anode’s superior mechanical and electrochemical robustness during normal and induced dendrite shorting occurrences while providing quality of plating in commercial operation. De Nora specialists focus on key components, in particular the engineering of the self-protection system, DSA® anodes and catalyst formulation capable to cope with high levels of pollutants while providing long service life in the meantime. Results of field trials confirmed the expected anode performance and enabled the selection of the most suitable “SPA” structure, based on resistive protective elements. Summarizing the economic benefits to copper electrowinning tankhouse operation with De Nora’s self- protected all DSA® anodes are; Double-digits power savings Cobalt-free electrolyte operations Minimal dendrite shorting damage incurred at the SPA anode Smoother, uniform cathode deposits with tangible improvement on current efficiency Tankhouse operations producing lead-free copper quality cathodes, in addition to elimination of lead waste for improved operator health and environment. INTRODUCTION De Nora’s engineered “Value Technology Package” (“VTP”) for electrowinning, consisting of our DSA® anodes coated with mixed metal oxide specifically formulated for copper electrowinning in conjunction with an advanced self-protected full titanium anode (“SPA”), underwent an intense field qualification program, inclusive of the behavior under massive short-circuits as part of the field investigation, with the goal to select and appoint the ultimate design configuration of “SPA”. Optimized wireless-based monitoring system was included in the field program, demonstrating good functionality for cell parameters monitoring and remote shorts detection.

Jan 1, 2019

By A. Thatcher, C. Day, C. Meyer

The purpose of this paper is to provide general information about the bioaccessibility of metals and specific information about the use of bioaccessibility in risk assessments (human health risk assessments [HHRA] or ecological risk assessments [ERA]) and a list of sites where regulatory agencies have approved the use of bioaccessibility data in risk assessment. The memorandum also cites current U.S. Environmental Protection Agency (USEPA) guidance as well as state specific guidance where applicable. BRIEF HISTORY OF METAL BIOACCESSIBILITY TESTING AND METHODS The bioaccessible fraction of a constituent is that fraction that dissolves or desorbs from its matrix (e.g., soil) in the gastrointestinal tract and is available for absorption (USEPA 2007a; ITRC 2011; ITRC 2017). This is different from the bioavailable fraction, which is the percentage of the amount of an element that an organism is exposed to that is absorbed by that organism during a given time under defined conditions (USEPA 2007a). The bioaccessibility factor is the percentage of a metal that is potentially available for absorption and, therefore, is a conservative estimate of the bioavailable fraction since all that is available for absorption may not ultimately be absorbed into the organism’s system. Currently, there are two main techniques for estimating bioavailability of metals within a medium: in vivo animal studies (time-consuming and often cost-prohibitive), and in vitro tests that simulate human, or animal digestion in a laboratory setting. In vitro and in vivo test methods and protocols have been extensively evaluated by numerous researchers (Ruby et al. 1996; Rodriguez and Basta 1999; Sips et al. 1998; Sips et al. 2001; Molly et al 1993; Oomen et al 2002; Kelley et al. 2002; Oomen et al. 2003; Furman et al. 2006; Drexler and Brattin 2007; Basta et al. 2007; Wragg et al. 2009; Wragg et al. 2011; Chaney et al. 2011; Bradham et al. 2015; Bradham et al. 2018). The most recent scientific literature demonstrates that protocols used to estimate the bioavailability of metals to mammals also predict bioavailability of metals to birds as well (Beyer et al., 2016).

Jan 1, 2019

By Jerry C. Tien, Yingjiazi Cao

"Coal spontaneous combustion (SponCom) is a natural phenomenon in underground operations, which can either happen naturally or be triggered by human activities. For underground operations, espe-cially in coal, SponCom can happen frequently as a result of air leakage, although its incubation period may vary depends on types of coal and surrounding environment, resulting in uncertainty in control. In China, most of the underground coal operations now use longwall mining method because of its superior safety, high productivity and efficiency. With an increased popularity, there is also an increasing necessity to study spontaneous combustion, its occurrence and management. There have been many theoretical analysis and experimental studies over the past half century hoping to understand the occurrence of coal combustion and its control measures to better understand the occurrence and to design controlling measures to limit the dam-age it causes. In this paper, research on coal spontaneous combustion fundamentals from these three aspects will be reviewed, gaps highlighted and possible directions for future studies. INTRODUCTION The history of anthropic development is the history of human's energy utilization progress. From the first usage of fire, people have been continuingly seeking energy resources on earth. Coal, as an abundant, economic and convenient source of fuel quickly became indispensable and made significant contribution to economic growth worldwide. With technology and societal development, people are becoming more and more coal-dependent, but at the same time, problems of fossil fuel combustion came into sight. In global coal mining industry, spontaneous combustion has now presented one of the most challenging safety issues, it is also believed that it has contributed significantly toward the climate change. It is essential that more effort be invested to examine the cause of SponCom and its control measures. Coal SponCom is a complex process, with both physical and chemical inter-actions among various interrelated factors such as local airflow distribution, ventilation pressure, methane emissions (if any), and physical surroundings underground. With the advent of powerful computers, simulation techniques and af-fordable modelling packages in recent years, significant advances have been made in understanding sponta-neous combustion. But because of the complex nature of combustion and varying underground conditions, there are still areas that need further examining. This paper will focus on illustrating the current research of coal spontaneous combustion and addressing research gaps and future study areas."

Jan 1, 2019