Search Documents

By B Roache, A Vakili, R Talebi

When a highly anisotropic or weak rock mass is subjected to high-stress conditions, it can lead to large ongoing deformations or squeezing ground conditions. Squeezing ground conditions can impose increased support costs, delays associated with rehabilitation, and disruption to production schedules. Ultimately, in more severe cases, it may result in complete drive closure. Several recent case studies investigated the squeezing mechanism and measures to control squeezing ground in underground mines and also to design appropriate ground support systems. Effective management of squeezing ground conditions requires a sound understanding of the failure mechanism and the driving forces. Once the failure mechanism is understood, the appropriate ground support system should be tailored to specifically manage the critical driving forces that control the squeezing mechanism. Support type, support stiffness, reinforcement length, support density, installation times and mining sequence all have important impact on the effectiveness of the support system. This paper provides a case study at the Ballarat Gold Mine in Australia, where drive squeezing was associated with foliated ground conditions located below 700 m depth. Numerical modelling was used to better understand the failure mechanism and the driving forces that lead to squeezing conditions. The effectiveness of various support types was compared to installed ground support performance. This has provided a credible methodology for assessing and optimising the selection of reinforcement in squeezing ground conditions. CITATION:Talebi, R, Roache, B and Vakili, A, 2018. Understanding and modelling squeezing ground conditions at the Ballarat Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 107–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Turner, P Hills, D Johnson

Underground mining for gold began in Beaconsfield in 1877 and development of the Tasmania Mine saw the sinking of multiple shafts, including the Hart Shaft over the ensuing 35 years. The mine closed in 1914 at a depth of 455 m due to prevailing economics, eventually reopening in 1999. The modern mine closed in 2012 after extending the mine from a historical depth of 455 m to the exhaustion of the modern Ore Reserve at a depth of 1210 m. West Tamar Council took over the lease for the immediate area around the Hart Shaft as an extension of the adjacent museum. The Hart Shaft and above ground structures became a significant drawcard for visitors. Tasmania was affected by sustained wet weather during May, June and July of 2016 which caused severe flooding and significant Statewide damage. This uncharacteristically intense wet weather caused saturation of the ground surrounding the Hart Shaft. Eventual shaft failure was first identified in August 2016. The failure of the shaft occurred at approximately 50 m below surface and resulted in a plug of material completely blocking the shaft. Significant surface subsidence affecting the surface infrastructure ensued. Due to the unstable nature of the surrounding material, it was determined that addressing the failure above the blockage would not provide a permanent solution to prevent the continued flow of material into the shaft. Many options to stabilise the shaft were considered, however it was assessed that a concrete plug in the shaft in competent ground at a depth of 100 m below surface and well below the blockage, would provide the only long-term solution. Man-entry was considered unsafe. The solution to access ultimately entailed filling the entire shaft with granular fill up to 100 m depth to act as formwork for a concrete plug. The rising mains at 400 mm and 250 mm diameter, which remained in place in the shaft, provided the avenue for placing the fill and ultimately, the concrete plug. Once the plug was in place the remainder of the shaft up to the underside of the blockage and over the top of the blockage to the surface was successfully filled with a combination of more granular fill and flowable cement stabilised sand. The Hart Shaft and surrounding above ground infrastructure was successfully stabilised and re-opened to tourist access. CITATION:Johnson, D, Turner, A and Hills, P, 2018. Stabilising and filling the Beaconsfield Hart Shaft, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 42–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Carswell, K McTyer

The Pajingo gold operation in Queensland is approximately 50 kilometres south of Charters Towers and 134km south-west of Townsville. The resource was discovered in 1983 and first open pit gold production began in 1986. The mine traditionally employed a bottom-up sequence – a combination of modified and traditional Avoca methods with run-of-mine waste backfill. This practice caused many high-grade crown pillars to be left in place, yet accessible. In recent years, these crown pillars have been extracted by injection grouting of rockfill. This process facilitated blind up-hole open stoping. To date, thirteen separate injection campaigns have been completed, of which ten were deemed successful. In general, the two key technical difficulties in this mining technique are: maintaining a consistent high-quality ground consolidation of the rock fill material; and controlling the drill and blast practices during stoping. Here, effective drill-and-blast control was found to be essential to achieve the dual aims of 100% extraction, and maximum sill pillar stability to minimise dilution. During stoping, the technical performance of the consolidated rock-fill was recorded; both to verify the design, and to identify operational improvements. The results showed that Pajingo has realised both reduced production down-time through use of early strength gain grout, and more rapid and thorough grout consolidation through changes to the emplacement method. The optimisation of consolidated rock fill has led to several quantifiable benefits to the mine, including: profitable extraction of previously sterilised crown pillars resulting in both increased ore reserves and production profile; improvements to the stability of grouted stope crowns, thereby reducing safety and production related; risks associated with open up-hole stopes; reduction in cost and time constraints, with respect to the grouting of loose fill; and reduction in grout curing time – from 14 days to 8 days – thereby minimising production down-time. This paper is a case study of the evolution and optimisation of the up-hole open stoping mining method at Pajingo. The challenges and successes are discussed in terms of their key mining outcomes. CITATION:McTyer, K and Carswell, J, 2018. Evolution of rock fill consolidation at Pajingo Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 66–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E Holloway

The optimisation of an open pit mine can be broadly split into two stages, the first being the ultimate pit optimisation (and subsequent stage designs), and the second being schedule optimisation. Macroeconomic uncertainty clearly impacts on both however interrelationships do also exist. Generally, the opportunity exists for the ultimate pit to be revised during each planning cycle, however when this reprieve is removed the uncertainty for the underlying business increases. As one example, the introduction of an in-pit waste dump can be seen to significantly limit the option to revise the ultimate pit. When in this situation there are two potential risks that present: (i) the long-term price used for the ultimate pit selection is optimistic, and too large of a pit is selected resulting in waste being mined which uncovers material not of a significant value to deliver a profit; (ii) the long-term price used for the ultimate pit selection is pessimistic, too small of an ultimate pit is selected, and ore of realisable economic value left behind. Both of these outcomes are risks and as such can be assessed and quantified. CITATION: Holloway, E, 2018. Incorporating economic variability into a strategic planning framework, in Proceedings Complex Orebodies Conference 2018, pp 88–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S Roberston, G Batt, R Shanahan, B Shah, A Trench, H Bromfield

The geographic imperative of ore systems leaves mining, more so than virtually any other aspect of modern industry, heavily dependent on obtaining and maintaining social licence to operate. A prospective miner cannot arbitrarily walk away from a deposit in search of more favourable community perceptions – concentrations of mineral endowment represent highly specific and fixed elements of the landscape, and their development and extraction thus requires the acceptance and trust of a specific network of landholders and stakeholders, sometimes with diverse and even competing interests in the development and use of the local environment. Weakness or absence of such social licence can bring added costs and complexity to developing and operating a mine – and in extreme cases even result in project failure. Because it must be maintained throughout the life of a project, such social risk becomes a substantial part of overall project risk profile, particularly during routine operations once initial technical and development risks have been largely resolved.CITATION: Bromfield, H, Roberston, S, Shah, B, Shanahan, R, Trench, A and Batt, G, 2018. On equitable distribution of mining wealth and the social licence to operate imperative – an African case study, in Proceedings Complex Orebodies Conference 2018, pp 6–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By R Valenta, J Owen, D Kemp, E Lebre, G Corder, J Thomas

Numerous recent analyses have shown that future demand for a broad range of critical commodities is unlikely to be met by new discoveries and recycling alone. The only practical alternative source to address this shortfall comes from orebodies which are currently either uneconomic or inaccessible. A common assumption is that a simple rise in commodity price will render these deposits economic. The mining industry has a long history of innovation allowing economic production from increasingly low grade and technically challenging orebodies. Industry “roadmaps” have been produced on a regular basis, with the aim of identifying future innovations which will allow this progression to continue. At the same time, there have been relatively few systematic analyses of the actual range of challenges facing undeveloped orebodies. The aim of this study is to analyse the mix of challenges faced by a group of undeveloped orebodies in order to better understand the relative importance and necessity of innovations applicable to the deposits, with the ultimate aim of determining the relative value and impact of possible innovations to the economic viability of those deposits. CITATION: Valenta, R, Lebre, E, Kemp, D, Owen, J, Corder, G and Thomas, J, 2018. Can a simple price-rise unlock complex copper orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 71–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By W Potma, C Brauhart, S Halley, S Urbisinov, A Scogings

Truly integrated, quantitative, 3D GEOmetallurgical (or mineral system) characterisation, classification and 3D modelling should provide a cradle to grave unifying link across the exploration and mining value chain. All too often, spatially representative (quantitative) characterisation and modelling of a mineral system is delayed until feasibility stage, incurring a significant opportunity cost. The application of robust GEOmet characterisation methods early in the project lifecycle (at exploration stage) improves ground selection, exploration, and Mineral Resource estimation outcomes, long before there is a need for metallurgical test work. The value of this early provision of quantitative 3D mineralogy models is compounded at project feasibility stage, and continues to accrue over the entire project lifecycle, delivering cost savings, improved decision making and early warning of issues and opportunities.CITATION: Potma, W, Halley, S, Scogings, A, Urbisinov, S and Brauhart, C, 2018. Putting the ‘GEO’ back in front of GEOmetallurgy: importance of early implementation of quantitative mineral system characterisation, classification and modelling, in Proceedings Complex Orebodies Conference 2018, pp 55–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A Tsoy

This abstract describes long-term mining schedule optimisation approach that may be suitable for complex marginal projects and is based on modern scheduling techniques. CITATION: Tsoy, A, 2018. Strategic mine schedule optimisation, in Proceedings Complex Orebodies Conference 2018, pp 91–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018

By J. Ning, T. Bu, J-Q. Jiang, L. Jiang

"In coal mining in China, the cutting height of the shearer in longwall faces is increasing. Owing to the increase of extraction height, the caved roof strata area is enlarged, and new issues are being encountered, such as determination of a suitable working resistance for the shield and control of the roof. Through field observation and theoretical analysis of the first longwall face with a height of 6.0 m in the Bayangaole mine, a three-stage structural model was developed. Stage I is defined as the period in which the lower immediate roof (LIR) caves into the goaf and is broken into irregular shapes of various sizes. Stage II is defined as the period in which the upper immediate roof (UIR) breaks and impacts the LIR. In stage III, the main roof breaks into blocks and then impacts the UIR. With respect to these three stages, a suitable method was identified for calculating the working resistance of the shield support for a super-great mining height longwall face (SGMHLW). Introduction and backgroundThe coal seams in the Shendong coalfield, located in the northwest of China, are characterized by low dips and large thicknesses and are thus suited for full thickness extraction. Since the mid-1990s, the Shendong coalfield has been developed into one of the largest in the world (Ning, Liu, and Tan. 2014; Ning et al., 2017). Recent developments in mining equipment have made it possible extract entire seams up to 5.0 m thick in a single cut. This method, termed the ‘super-great mining height longwall face’ (SGMHLW) method, has been widely adopted in the Shendong coalfield (Table I) (Ju and Xu, 2013; Peng, Li, and Zhou 2015; Zhang, Fan, and Ma 2011). According to some studies, sudden support-closure incidents often occur when using the SGMHLW method. The key to solving this engineering issue is to have a clear understanding of the structural characteristics and movement laws of the overlying strata. For instance, the load on the supports is related to the movement of the roof stratum as a response to the mining activities."

Nov 1, 2018

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

By M. Gomo, L. S. Mokhahlane

"Underground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for electricity generation. Residue products from UCG have the potential to leach into surrounding groundwaters. The geochemistry and leaching dynamics of these products are explored in this study. The products include char, ash, and the heat-affected zone in the surrounding rocks. Core samples from the pilot plant at Majuba are the first ever to be recovered from a UCG cavity in Africa, and they give key insights into the geochemistry of the gasification zone. Mineralogical and chemical analyses were performed on the samples, and acid-base accounting (ABA) was used to predict the acid-producing capacity of the gasification zone, particularly for char samples. Some of the char contained pyrite, although not all samples were acid-producing as determined by the ABA analysis. The ABA results showed that some of the unburned coal has moderate levels of sulphur, which could be the driving medium for acidic conditions. The ABA analysis indicated that water in contact with the gasification zone would eventually have a pH lower than 7, which could lead to acid rock drainage. These results form part of a preliminary investigation into the geochemistry of the reaction zone, post gasification. IntroductionUnderground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for industrial purposes, including electricity generation. The gasification process leads to the formation of a cavity composed of char, rubble, and void space (Bhutto, Bazmi, and Zahedi, 2013). Residue products from UCG have the potential to leach into groundwater. These products include char (devolatilized coal), which can generate acid rock drainage (ARD). ARD is caused by the oxidation of sulphide minerals, which acidifies the leachate, thus increasing the solubility of some environmentally toxic metals (As, Cd, Hg, Pb, Zn, etc.) (Bouzahzah et al., 2015).The main source of ARD is oxidation of sulphide-bearing minerals due to interactions with oxygen, water, and microorganisms (Simate and Ndlovu, 2014; Kefeni, Msagati, and Mamba, 2017; Bouzahzah et al., 2015). Although ARD occurs naturally, it can be enhanced by mining activities that escalate exposure of sulphide minerals to water, air, and bacteria (Simate and Ndlovu, 2014). At the Majuba pilot plant, the unburned coal remaining in the cavity has been in contact with groundwater since the gasifier was shut down in 2013. It is possible that in a commercial UCG plant, most of the coal will be consumed and no unburnt coal will be left in the cavity. Most of the sulphur will be converted to H2S during the gasification process and transported with the syngas to surface, where it can be removed and captured as elemental sulphur."

Oct 1, 2018

By T G. Vizcarra, T J. Napier-Munn, A T. Karbowiak, M G. Hart

Squeezing extra performance from existing equipment (‘sweating the assets’) is key to continuous improvement initiatives, particularly during times of cost cutting where the option of spending additional capital to facilitate circuit upgrades can be severely constrained. A common challenge, however, is identifying the best combination of settings for different process variables, as their effects can be camouflaged by interactions with other process variables and, of course, noise in historical data.This paper describes a recent investigation at Boyne Smelters Limited to identify strategies to coarsen the product of its dry, fixed-speed, open-circuit AG mill, without the need for installing pre-screens prior to the mill. The product is used as insulation material for the reduction of alumina to aluminium, and an excessively fine product was inhibiting the ability of the cover material to dissipate heat from the underlying anodes. The approach was to undertake a series of experiments, designed according to statistical criteria, to elucidate the effect of key process variables (feed blend and power draw) upon the product sizing. The results provided clarity about what strategies would encourage the production of a more desirable mill product (with some surprises). The study is a good example of how properly designed experiments can identify hidden potential in processing circuits, thereby mitigating the need for capital-intensive upgrades.CITATION:Vizcarra, T G, Hart, M G, Karbowiak, A T and Napier-Munn, T J, 2018. Getting the most from existing processes: using cleverly designed experiments to optimise the line 3 AG mill at Boyne Smelters Limited, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 207–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S H. Algie, E J. Knoblauch, I A. Lovatt, S G. Doig

Mill operating teams are expected to engage in a perpetual quest for process improvement – pushing the boundaries of practical process limits and testing new technology to achieve the next step-change in plant performance. Often the barrier to improvement lies in gaining management approval for process changes.Getting approval for investment in novel technology carries an added degree of difficulty, particularly in risk-averse operations, when it challenges conventional wisdom. A case in point is a new technology for controlling variability in slurry distribution. There is a widely held view that less-than-specified classification efficiency and spraying and roping of individual units in a hydrocyclone cluster, must be accepted as unavoidable. That these are wholly correctable deficiencies resulting from unequal loading of the individual units seems a bold claim. Wouldn’t the high turbulence of pumped slurries overcome all potential for segregation of solids? This paper discusses how the task of developing confidence in a new technology can be approached by a combination of physical modelling at small scale, and full-scale operating experience. Proving efficacy then leads to the next task: demonstrating value. Again, the particular technology serves as an example that could be of value to others developing relatively low-cost technologies. A high-pay-off as an investment may be achieved with improvements in metallurgical performance that are small in relation to normal process variations. This has led to an exploration of how process simulation modelling could be used, in conjunction with production data, to provide a benchmark for the expected change, which could be expressed in monetary terms.The next goal, which is currently being achieved in operating plants, is to realise the greater value now available through the optimisation of cyclone configuration, which becomes practical when the confounding effects of cluster instability are removed through equal loading.CITATION:Doig, S G, Algie, S H, Lovatt, I A and Knoblauch, E J, 2018. Investing in new process improvement technology: reducing the risk of implementation – a way forward, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 571–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Carrillo, A King

Gravity recoverable gold (GRG) is largely distinguished from other gold by its non-mineralised, metallic form, its high degree of liberation from the ore and its appreciable particle size. The gold mining industry has so widely accepted the use of batch centrifugal concentrators (BCC) and intensive cyanidation (IC) systems for the recovery of GRG that these may well be considered requirements of any plant processing ore containing appreciable GRG. The recovery of gold by gravity is quick, easy and cheap by comparison to alternatives. However, there are cases where attributes of the ore make recovery of gold by gravity and IC unusually challenging. This paper describes three examples where such challenges have been encountered and met, including those where the ore contains cyanide soluble base metals and where fine GRG is to be recovered from flotation concentrate.CITATION:King, A and Carrillo, J, 2018. Addressing challenging applications of intensive cyanidation in gravity gold recovery, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 283–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By P Rubie, J Russell

This paper looks at the past, present and not too distant future of grinding mill relining.Since the adoption of autogenous grinding (AG) mills and semi-autogenous grinding (SAG) mills as the primary ore reducing devices in the comminution circuit, plant shutdown frequency and duration has largely been driven by the liner maintenance requirements of these mills.The past 30 years have seen the introduction of many technologies to reduce relining times and frequencies. Advanced relining systems have been developed which include single and twin Mill Relining Machines, capable of placing large (up to 8000 kg) liners, high energy recoilless THUNDERBOLT Hammers, and high capacity Feed Chute Transporters. Despite these advances, today many of the hazards associated with mill relining remain and reline times still vary considerably between mine sites. A sophisticated discrete event simulation program, designed to analyse the mill relining process, has revealed the dominant influences on reline times of crew performance and of the need for safe access to larger segments of the mill.A new generation of advanced and semi-automated technologies is currently being tested that will address these remaining challenges. These technologies remove people from the hazardous environment inside the mill and will allow techniques used in modern advanced manufacturing to provide a near-future step change in mill relining safety and performance.CITATION:Rubie, P and Russell, J, 2018. 21st century relining – the path to greater mine site profitability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 621–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Seppelt, B Akerstrom, A Rice, J Bubnich, T Waters

The Concentrator 1 plant at Cadia transitioned from Cadia Hill open pit to the Cadia East block cave ore body in 2013. As a result of this change, major plant upgrades were required to achieve the desired throughput while treating more competent ore. The 40-foot (40’) SAG mill now receives a feed of predominantly high pressure grinding rolls (HPGR) product with a minor component of secondary crushed ore at a combined F80 of 17 mm. The significant reduction in feed size to the SAG mill has markedly changed the operating characteristics of the mill, which has been extensively studied since commissioning in 1998.This paper examines the operation of the 40’ SAG mill in its new configuration in the Concentrator 1 circuit. Operational stability is highlighted as a significant factor in delivering mill performance, which has been achieved through several key improvement projects utilising a theory of constraints framework. Five years of successful project implementation has progressively lifted the maximum processing rate of Concentrator 1 from the design estimate of 2455 t/h to above 3000 t/h. CITATION:Waters, T, Rice, A, Seppelt, J, Bubnich, J and Akerstrom, B, 2018. The evolution of the Cadia 40-foot SAG mill to treat the Cadia East orebody: a case study of incremental change leading to operational stability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 217–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By E Asakpo, S Chaffer, A Heath

Newmont has had continuous production at their Ahafo operations, Ghana, since 2006. In 2013, Ahafo initiated an efficiency programme to improve mill performance and reduce energy consumption. Following this assessment, a Turbo Pulp Lifter (TPLTM) was installed in the Ahafo SAG mill in April 2015 to replace the existing radial pulp lifters. Plant operational data showed delivery of a power saving of 10 per cent, an improvement in throughput of 3.3 per cent, with no loss of grind size. Pulp lifter life was also doubled from 11 to 22 months.However, during subsequent relines when the grates were removed it was found that one in four of the outer pulp lifters were wearing at a faster rate than the remainder. This was investigated by Discrete Element Method (DEM) modelling, which predicted some overtopping and internal recycle within the pulp lifter. Significantly, the model predicted that the recycled material would pass back down every fourth outer pulp lifter, matching the field observations. Subsequently, the DEM investigation was continued and became an R&D project to improve the TPL design. The results are summarised here, leading to the development of the next generation Spiral TPLTM.CITATION:Heath, A, Chaffer, S and Asakpo, E, 2018. The development of optimised pulp lifter design for the Ahafo SAG mill using discrete element method modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 585–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018