Search Documents

By Diego José Inforzato

Hot tensile data were correlated with creep data, in Aluminum Alloy AL7475-T7351, as part of a broader research program, aiming at the validation of a methodology that proposes an equivalence between the two kind of results, for metallic materials in general. The methodology is based on a criterion that establishes correlation among the following parameters from each test: the strain rate, ultimate tensile stress, and time to reach the ultimate tensile stress, in tensile tests, are equivalent respectively to the: minimum strain rate, applied stress and rupture time, in creep tests, for a given test temperature. The present material was tested at 3 temperatures: 133,166 and 193ºC, using 3 nominal tensile strain rates in the hot tensile tests: 3.2x10-6, 1.6x10-4 and 6.4x10-3 s-1 and 9 applied stress levels in the creep tests, varying from 140 to 400 MPa. The conversion of the hot tensile data to creep-like data allowed performing the analysis of all the results together according to the traditional creep relations proposed by different authors, namely: Norton, Arrhenius, Zener-Hollomon and Monkman-Grant, with the determination of the corresponding parameters in each case. The equivalence between hot tensile and creep data is also confirmed for this aluminum alloy.

Aug 8, 2018

By Andressa Alves da Silva

Nowadays, population growth and the interest of food industry, makes the research and applications of biodegradable polymers increase, because under favorable conditions its degradations may occur within weeks or in a few months, reducing the environmental impact. This work presents the processing and characterization of flexible films by the incorporation of 3 % (% wt) of modified bentonite light green clay in the Copolyester/PLA biodegradable blend. The clay incorporation was carried out by melt-mixing processing, using a twin screw extruder machine. The films were obtained by cast extrusion tape. The films obtained were submitted to tensile tests, SEM and XRD analysis, and the correlation between their properties was discussed. The XRD results of clay showed that the quaternary salt and sodium carbonate addition increased the interlayer distance of clay making it easier to intercalation of blend in the nanoclay. The XRD results of PBAT/PLA/Clay nanocomposite show no characteristic organoclay peaks. This result suggests intercalation between nanoclay and matrix (blend). The tensile test results showed an increase of around 30% in tensile strength at break of nanocomposite film when compared with blend film.

Aug 8, 2018

By Ananda Moreira Vaz Ourique de Avila

High and intermediate temperature fuel cells (FC) are power generators characterized by high efficiency and their use in cogeneration systems. The single fuel cells are connected in series by the use of interconnects to form a fuel cell stack. Ferritic stainless steels have been used in the making of high and intermediate temperature operation solid oxide fuel cells interconnects. However, at high temperatures, on the order of 700-8500C, these steels can present significant oxidation and degradation processes, promoting increased electrical resistivity and corrosion losses that result in contamination of the electrodes and reducing the performance and the useful life of the FC. Intensive R&D activities have been made to minimize these problems and the use of composite coatings on metallic substrate has been considered. This paper evaluates the use of coatings of copper and nickel, with particles of La2O3, Y2O3, CeO2, LaCrO3 and doped chromites applied on ferritic stainless steels AISI 430, AISI 441 and Crofer22APU produced by electrodeposition. The produced samples were evaluated by microscopy techniques, gravimetric analysis and by electrothermal characterization. The most significant results were obtained with chromites coatings (LaCrO3 pure, mono- and multiple-doped) showing the combination of the best features of metal coatings, substrates and ceramic particles with semiconductor properties.

Aug 7, 2018

By Ulysses Forastieri de Matos

A injeção de combustíveis auxiliares pelas ventaneiras dos altos-fornos vem se mostrando, nas últimas décadas, como uma técnica de redução do consumo de combustíveis e conseqüente redução de custo de produção de gusa. Uma das últimas técnicas de injeção de combustíveis auxiliares pelas ventaneiras, utilizada por algumas usinas siderúrgicas integradas a coque, no Brasil, nos últimos anos, é a injeção de carvão pulverizado e gás natural simultâneamente, aqui chamada de co-injeção. O presente trabalho apresenta os resultados obtidos na utilização desta modalidade de injeção em escala industrial.

Aug 1, 2018

By Tobias Krull

The characterisation of iron ore from a materials handling point of view is paramount in order to provide the best possible design for the desired application and maximise equipment uptime at the lowest possible capital and operational expenditure. Problematic issues in materials handling applications often arise in the iron ore industry due to the high density of the ore as well as the abrasive nature of the product. One of the key issues encountered during the handling of iron ore is excessive wear due to either impact or sliding abrasion. The applications and equipment typically affected by accelerated wear issues are mass flow hoppers, transfer chutes and conveyor belts. These wear issues often result in unplanned down times and loss in production which can lead to a considerable loss in revenue. This paper provides an overview of the best practises in the materials handling characterisation of iron ore and discusses available techniques for the modelling of iron ore in applications where accelerated wear is experienced. The application is illustrated through a number of industry relevant case studies for which engineering design work was undertaken to successfully reduce the wear rates of different materials handling equipment.

Aug 1, 2018

By Luiz Henrique Accorsi Gans

First, this works carries an experimental evaluation for austempered ductile iron (ADI) as a gear material. And second, in order to provide a better understanding of the microstructural effect on the stress state of subsurface regions, a finite element method approach was considered using the submodeling tool in ANSYS 11.0. For this, ADI gears were produced from continuous cast iron bars, heat and thermochemical treated and tested in FZG test rig. The results were compared to those of carburized steel AISI 8620 and induction hardened steel AISI 4140 gears. The wear experiments were performed at the temperature of 90ºC with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state). The time for pitting and spalling on the gears surfaces were measured using image analysis. The results showed a very good potential of using ADI for manufacturing gears, replacing induction hardened steels. Also, the ADI gear with smaller nodules showed higher life for pitting. In contact fatigue tests with severe load, the carburized AISI 8620 steel proved more adequate than the austempered ductile iron, showing that the mechanical properties are critical in the resistance to damage in gear contact. The austempered ductile iron with smaller nodule size showed to be very competitive with wear resistance similar to AISI 4140 steel induction hardened. With ANSYS, it was verified that the nodule size affects the gears life independently of the mechanical properties of the matrix. The results showed that the nodules indicate the presence of a concentration stress, but their size doesn’t affect the contact fatigue life as much as the total amount of nodules, regardless of the ductile iron microstructure. The size and number of nodules affects both the nucleation and the propagation stage of cracks. ADIs with higher amount of nodules have a greater wear resistance. Also, compared to the Hertz contact theory (isotropic material), the presence of graphite nodules indicates a non-isotropic material and made the maximum shear stress point moves toward the surface.

Jul 31, 2018

By Kelen Juliane Mucelin

In order to better understand the tribological behavior of self-lubricating materials, Fe-Si-C matrix composites containing solid lubricants added during the mixing step were studied. The samples were produced by conventional powder metallurgy route, presenting total contents of 5%, 7.5% and 10% in volume of h-BN and graphite mixtures as solid lubricants. The composites were evaluated in terms of tribological properties, under reciprocating sliding conditions, and mechanical properties by using tensile tests. Additionally, the wear scars were characterized by Raman spectroscopy and scanning electronic microscopy. Higher total contents of solid lubricants greatly increased scuffing resistance however decreased mechanical properties. Furthermore, increasing h-BN contents reduces both properties. These results confirmed the applicability of such sintered composites as self-lubricating parts, reaching values up to 7000 N.m for scuffing resistance combined with ultimate tensile strength of 220 MPa.

Jul 31, 2018

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Ronaldo Câmara Cozza

Iron aluminide alloy; Ball-cratering wear testing; Rolling abrasion; Wear volume; Coefficient of friction

Jul 31, 2018

By Qingwen Dai

The Marangoni effect is an important phenomenon where a surface tension gradient drives liquid towards high surface tension regions. Temperature gradient, evaporation, disparity of viscosity, and surface roughness and topography are all significant factors that can affect this thermo-capillary migration. The purpose of this study was to investigate the influence of micro-groove patterns on the migration of paraffin oil, and obtain a well-designed texture of micro-grooves to prevent the thermo-capillary migration. Patterns of micro-grooves with differing orientations and geometric parameters were fabricated on the surface of SUS 316 stainless steel substrates. Experiments on the migration behavior with different viscosities of paraffin oils were carried out various temperature gradients. The experimental phenomena indicated that the surface with the micro-grooves perpendicular or parallel to the temperature gradient have a strong impact on the migration performance of paraffin oil. Micro-grooves perpendicular to the temperature gradient exhibited extraordinary slower migration velocity than that of the parallel one. Width and depth of micro-grooves had an obvious influence on the behavior of temperature-driven migration and detail discussions on the effects of these geometric parameters were carried out.

Jul 31, 2018

By Charles de Abreu Martins

An experimental investigation was conducted using laboratory-processed, 0.12C–1.70Mn–0.2V steels with different Cr or Mo additions aiming to evaluate this influence on the microstructure and mechanical properties hot rolled steels. Steels were processed in a pilot rolling equipment, simulating a typical thermomechanical processing, with finishing rolling steps above Ar3, followed by accelerated cooling and 723 K (450 Celsius) coiling temperature. Microstructures and precipitates were analyzed using OM, SEM and TEM, while mechanical properties were evaluated by tensile and hole expansion tests. Since Cr and Mo increase hardenability of austenite, and as a consequence, the volume fraction of the acicular constituents increases with gradual additions of Cr or Mo. Moreover, Cr or Mo impacted V precipitation process, reducing average size of particles. At 0.50%Mo, V precipitation was inhibited. Effects of this microstructure evolution on the final mechanical properties were also analyzed, as well as a comparison between Cr and Mo effects, with Mo presenting more effective influence.

Jul 30, 2018

By Armando Vazquez

This paper will provide an overall technology update on Tenova’s modular i BOF® technology package for improved endpoint detection (Carbon and Temperature), slop detection and auto-tapping control, with a primary focus will be on Tenova's Slop Detection System (SDS). Accurate Slopping prediction is a critical tool in the operation of a BOF. It provides the steelmaker with an additional protective system to increase yield & productivity while reducing operating costs. Tenova Goodfellow's i BOF® slop-detection technology uses lance vibration analysis with real-time alerts to give steel makers advance warning of the onset of a slop and a measurement of the slop severity. The system is designed to provide direct feedback control of lance position and oxygen flow rate, for rapid mitigation of potential slopping events. This paper will provide a summary on how the i BOF® technology package has been implemented, including trials and general results.

Jul 30, 2018

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them there is the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. Thermodynamic studies related to the formation of mineral species containing Fe, O and Zn elements were carried on due to the influence of these compounds in hydrometallurgical EAFD recycling processes. In recent years, a rise in the chlorine content of this residue was observed, mainly motivated by the increased use of scrap with polymeric impurities containing this element. In this work, based on computational thermodynamics tool FactSage, a general overview of gaseous and minerals species (found in EAFD) formed by Fe, Zn, O, Cl, H and C is shown – representing the organic origin of chlorine. For this study, the PVC polymer was used as the chlorine carrier substance which contaminates the EAF load.

Jul 30, 2018

By Michael McDonald

The cold-rolled steel output of cold-rolling mill (CRM) complexes are sometimes constrained by their batch annealing facilities (BAF). This paper examines a cost-effective solution to increasing capacity and quality of the BAF thereby making additional capacity available for CRM output. The solution involves applying a structured system of scheduling and operation to the BAF, using a proven level-2 software model. The system presented has been applied to a wide variety of BAF with all the leading furnace brands. Whether using traditional HN atmosphere or 100% hydrogen, peak performance can be achieved when using a properly configured, on-line, physical thermodynamic model. Given that it is not practical to place a thermocouple in each coil that is being annealed, various methods have historically been used to estimate the time required to properly anneal all the coils in the charge. This paper examines how the latest technology, in wide use throughout the USA, uses a physical thermodynamic model to shorten average cycle times, thereby increasing productivity and reducing energy consumption. The paper also examines the benefit of building thermodynamically balanced charges to further optimize the BAF operation and improve quality consistency by decreasing mechanical property variations.

Jul 30, 2018

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Claudio Fabbro

The increasing demand of wire rod high carbon grades for both small and large sizes are challenging the wire rod producers to enhance new technologies by combining high plant productivity and efficiency of superior quality finished products with extreme process flexibility. The possibility to change process route according to the final application of the rolled steel grade and to simplify production planning is one of the most important keys to success that distinguishes the mill plants developed by Danieli. This paper will focus on the most important metallurgical and process targets and on the in-line heat treatment technologies representing the core of Danieli know-how on high carbon grades production.

Jul 30, 2018

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By Nicolás Lugo

The electric steel industry has reached a level of maturity in its relative participation in the world’s steel production. As the industry has grown and matured, EAF steel producers have participated in an ever more competitive market. This competition has led to a continuous search for lower cost alternatives for energy and input materials. Over the years, the Electric Steel Furnace community of operators has developed a variety of technological improvements geared to increasing EAF productivity. Operators have emphasized lowering operating costs and improving the quality of steels produced. Depending on market conditions, the EAF operators may run with different goals and priorities. In times of low demand, the goal may be to operate with an emphasis on cost and the goal of maximizing cost effective use of resources. When the market demand is high the goal may be to maximize EAF throughput. The objective of this work is to list some of the EAF operating best practices observed by our team in the electric arc furnace operations around the world. EAF operators can consider and possibly implement these practices depending on the specifics of each EAF operating reality.

Jul 29, 2018

By John Ross Middleton

Based upon 30 years+ experience in the Development, Implementation and Ongoing Support of Computer based Melt Shop Management Systems in about 40 plants in the UK, Europe and the USA, consideration of the overall facilities of a state of the art, comprehensive, Integrated Melt Shop System covering Melting and Secondary processes for all grades of steels and superalloys; the scope of functionality of these systems, covering Raw Materials and Consumables Procurement and Inventory Management, Laboratory Management, Melt Shop Scheduling, Furnace Charge and Additions Optimisation, Level 1.5 to Level 2.5 Materials Optimisation and Process Control Calculations, Process Data Recording, Management of Ladles, Furnace Bodies, Vessels and Moulds, Comprehensive Management Reporting and Integration with Corporate ERP Systems. The second section of the paper reviews the key ‘Success Factors’ to achieve rapid, successful implementation, comprehensive, fast response user support, continuing system improvement and maintaining ‘perfect fit’ of system to operations in an ever changing future technical, operations and business environment.

Jul 29, 2018