Search Documents

By M Blanch

Gas management practices across the Australian underground coal industry have evolved significantly since the early nineties with the introduction of hazard management plans, directional drilling techniques, surface gas predrainage methods, and the widespread use of ventilation and gas reservoir simulation software.The improvements are evidenced by a substantial reduction in the occurrence of outbursts and gas related delays during a period where coal production rates have increased three to four fold. The development of effective gas predrainage strategies have been afforded by the use of reservoir simulators and a significant increase in the availability of measured gas reservoir data, in particular gas content and composition, adsorption isotherms and permeability. That said significant opportunities remain to optimise gas drainage designs and increase certainty in the gas predrainage design process through an enhanced understanding of coal seam permeability and how it is applied in the gas drainage design process.This paper describes the discrepancies between measured and actual seam permeability found during the recent assessment of two pilot predrainage programs executed in the coal measures of Queensland’s Bowen Basin. The results of those programs illustrate the need to better understand the validity of measured permeability data. The history match method employed in the pilot well assessments is proposed as an integral step in the routine gas drainage design processes that will ultimately lead to increased certainty and flexibility in gas predrainage practices.CITATION:Blanch, M, 2017. Coal seam gas predrainage optimisation through an enhanced knowledge of coal seam permeability, in Proceedings Australian Mine Vent Conference 2017, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D Caley

During the response to the Moura No 4 disaster, use was made of the New South Wales Mines Rescue Service’s ‘Mineshield’ inertisation equipment. The equipment had to be transported from Newcastle, approximately 1400 kms, and the liquid nitrogen a similar distance. The time taken, and therefore availability of the liquid nitrogen, became a significant problem. Operational issues were also experienced during use. Typically the liquid nitrogen is converted to a gas (vaporised) before being injected into the mine. However, as the propane gas tanker used for the vapourising unit was delayed, an attempt was made to inject the liquid nitrogen directly down uncased boreholes. This proved unsuccessful.Following the Moura No 4 disaster and the Moura No 2 disaster, recommendations were made relating to having inertisation capacity for the Queensland coal mining industry. Today the Queensland industry has multiple options available for inertisation, including the high-volume GAG and smaller volume units such as boilers and membrane separation units. Although it ultimately aided re-entry into Moura No 4, most likely due to the issues associated with supply to Central Queensland, liquid nitrogen has not found favour within the Queensland industry as an inertisation tool.Coregas has commissioned an air separation plant in Mackay, improving the availability of liquid nitrogen to Central Queensland. Based on the availability of this nitrogen, recent sealing operations at Kestrel have trialled using liquid nitrogen and associated vapourising units. This paper details the practical application and findings of using liquid nitrogen during routine longwall panel sealing.CITATION:Caley, D, 2017. Using liquid nitrogen for the inertisation of goafs, in Proceedings Australian Mine Vent Conference 2017, pp 35–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By Paul Pugsley

The EMSpec sensor employs the principle of measuring the complex impedance of the target steel over a range of frequencies these impedance values in turn varies with transformation fraction of the steel. A full scale implementation of the Real Time Transformation Monitoring has been installed at a quality large European steel producer to show the benefits of such a system. A total of three EMSpec sensor heads have been installed between the exit Finishing Mill and the Down Coiler on a HSM. For the successful production of Dual Phase, TRIP and TWIP steels increased control of the cooling regime is demanded; the use of surface temperature measurements alone cannot guarantee to achieve the desired mechanical properties. The EMSpec sensor, which is engineered to withstand this harsh environment, in real time directly measures the percentage transformation of the steel in the cooling area, typically in the accelerated water cooling zone. Using the information from the sensors integrated into the mill model enhances the models ability to predict the transformation profile.

Aug 17, 2017

By Guilherme Corrêa Soares

The effects of temperature and strain rate on the mechanical behavior of a superelastic NiTi wire were investigated by uniaxial tensile testing. A universal testing machine with an attached heating chamber was used for the tensile tests. Temperature influence was studied through straining of samples until rupture at a fixed strain rate and temperatures of 25, 50, 75, 100, 125, 150, 175 and 200 °C. Strain rate effects were investigated by straining samples until rupture at room temperature and strain rates of 10-2, 5 x10-3 , 10-3, 5 x 10-4 and 10-4 s-1. The effects of temperature and strain rate on NiTi mechanical behavior were discussed in terms of critical stress to induce martensite and austenite yield strength, when applicable; upper plateau stress, transformation plateau length and ultimate plateau stress. It was found that increasing test temperature and strain rate shifted the stress-strain curve upwards, albeit temperature displayed a greater influence. Plateau length increased with temperature, but no significant changes were detected as a result of different strain rates.

Aug 17, 2017

By Anna Carolina Cerqueira Neves

As fibras sintéticas vêm sendo gradualmente substituídas por fibras naturais. Em comparação com a fibra sintética, fibra natural demonstrou vantagens econômicas e ambientais. Visto que apresenta características interfaciais com matrizes poliméricas que favorecem a absorção de energia de alto impacto pela estrutura. No entanto, até agora pouco foi avaliado sobre a fibra de cânhamo incorporada em matrizes poliméricas. Este estudo tem o objetivo de avaliar a resistência ao impacto deste tipo de compósito com matriz de poliéster reforçada com diferentes porcentagens de fibras de cânhamo. A resistência ao impacto aumenta proporcionalmente com a quantidade relativa de fibras incorporadas como reforço na matriz polimérica. Este desempenho foi relacionado com a dificuldade de ruptura imposta pelas fibras, resultante da interação da matriz de fibra de cânhamo / poliéster de forma a ajudar a absorção da energia de impacto.

Aug 17, 2017

By Pedro Gabriel Bonella de Oliveira

O processo usual para elaboração de aços utilizados na indústria de petróleo e gás é a laminação controlada, porém, não é adequado para fabricação de peças de geometria complexa, como juntas e conexões. Nestes casos, o forjamento é a melhor opção, pois permite maior diversidade de conformação. A produção de componentes por esta técnica exige tratamentos de têmpera e revenimento para obtenção das propriedades exigidas em trabalho. O objetivo deste projeto é avaliar o comportamento em tração e a microestrutura de um aço microligado submetido ao aquecimento a 855, 900 e 1000°C. Modelos termodinâmicos de Kasatkin foram utilizados para cálculo das temperaturas de transformação austenítica. Os resultados mostram que o tratamento realizado na zona de transformação intercrítica favorece a formação de uma estrutura bifásica de ferrita e martensita com maiores valores da tensão de escoamento e resistência máxima à tração. Nos tratamentos térmicos realizados em maiores temperaturas há diminuição na resistência mecânica, porém com aumento no alongamento em consequência de uma estrutura composta de bainita e ferrita acicular.

Aug 17, 2017

By Anna Carolina Cerqueira Neves

Muito se tem estudado sobre materiais alternativos, como os compósitos de matriz polimérica reforçados por fibras lignocelulósicas. Isso se justifica pelo fato das fibras naturais terem vantagens no que tange ao meio ambiente, bem como relativo baixo custo. Além disso, a fibra natural apresenta características de interface com a matriz polimérica que favorecem as propriedades mecânicas pela estrutura do compósito. Esse presente trabalho objetiva analisar as propriedades de tração de compósitos de matriz de poliéster reforçados com 10,20 e 30% em fração volumétrica de fibras de cânhamo, que foram preparados alinhando as fibras em moldes e deixando-os curar por 24 horas em temperatura ambiente. Os corpos de prova foram testados numa máquina de ensaios Instron e os resultados mostraram um aumento na tensão máxima de ruptura com o aumento da porcentagem de fibra incorporada.

Aug 17, 2017

By Anna Carolina Cerqueira Neves

Atualmente, materiais alternativos têm sido pesquisados, sendo os compósitos dematriz poliméricas reforçados com fibras naturais um desses tipos de materiais. Ofato que torna as fibras naturais uma ótima opção são suas vantagens ambientais eseu relativo baixo custo. No caso do eu eucalipto, este também possui um altocultivo no Brasil. Além disso, as fibras naturais apresentam características deinterface com a matriz polimérica que favorecem as propriedades mecânicas pelaestrutura do compósito. Esse presente trabalho analisa as propriedades de tração docompósito de matriz poliéster reforçado com a incorporação de fibras de eucaliptoem 10,20 e 30% em fração volumétrica, que foram preparados alinhando as fibrasnas matrizes e curadas por 24 horas em temperatura ambiente, por volta de 25ºC.Os corpos de prova foram testados numa máquina Instron e os resultadosmostraram um aumento na resistência à tração conforme o aumento do volume defibras incorporadas.

Aug 17, 2017

By Dustin Vickress

The premature failure of copper staves in the lower stack and bosh is frequently the cause for an interim blast furnace repair at great cost to the blast furnace owner. Protective accretions may form on the stave hot face, but when these accretions are lost the staves can begin to deteriorate both due to abrasive wear from exposure to the descending burden materials and due to thermal cracking from exposure to hightemperature process excursions. These mechanisms can lead to failure of cooling passages, which forces blast furnace operators to shut off these channels, accelerating the rate of copper stave wear. Finger cooler technology was developed to extend blast furnace life by restoring cooling to damaged staves. Evidence for their effectiveness is presented herein in the form of experimental test work and conjugate heat transfer (CHT) analysis carried out using computational fluid dynamics (CFD) simulations. These tests demonstrate that under typical blast furnace excursion conditions, a stave fitted with finger coolers will undergo half the temperature rise of a stave fitted with conventional cigar coolers.

Aug 17, 2017

By Lucas Teixeira Costa

A crescente demanda por aços ultrabaixo enxofre em usinas integradas a carvão mineral tem levado a esforços para reduzir o teor de enxofre no gusa e no aço. Todavia, a falta de uma visão integrada dos processos acarreta em otimizações isolados que nem sempre contribuem para uma efetiva redução de custos e aumento de produtividade final. No presente trabalho, foi construído e validado um balanço de massa capaz de realizar uma previsão do teor de enxofre de final de sopro a partir das entradas iniciais de enxofre na carga metálica e nas adições de fundentes. Para isso, considera-se que ocorre transferência de enxofre entre as fases, segundo seus teores e o coeficiente de partição de enxofre. A raspagem de escória de tratamento de gusa deve ser feita com muito cuidado para promover a melhor remoção da camada sobrenadante e ao mesmo tempo evitar perdas no rendimento metálico no processamento do aço. Utiliza-se o teor de enxofre do gusa carregado no LD como o principal parâmetro de controle, e recomenda-se que seu teor seja superior a 20ppm, uma vez que o esforço necessário para reduzir para teores abaixo desse limite será totalmente perdido no LD, devido à reversão durante o sopro.

Aug 17, 2017

By Noan Tonini SImonassi

Fibras de rami (Boehmeria nivea) estão entre as lignocelulósicas naturais com potencial para utilização em compósitos poliméricos. O presente trabalho avalia a resistência ao impacto deste tipo de compósito. Corpos de prova normalizados foram confeccionados com percentuais de até 30% em volume de tecido de rami alinhadas ao longo de todo o comprimento. As fibras foram embutidas sob pressão em matriz de resina poliéster do tipo ortoftálica curada à temperatura ambiente por 24 horas. Os corpos de prova foram ensaiados em pêndulo de impacto Izod e as superfícies de fratura analisadas por microscopia eletrônica de varredura, MEV. A resistência ao impacto aumentou exponencialmente com a quantidade relativa de tecido de rami reforçando o compósito. Este desempenho foi associado à dificuldade de ruptura imposta pelas fibras bem como ao tipo de trincas resultantes da interação tecido de rami/matriz de poliéster que ajuda a absorver a energia do impacto.

Aug 17, 2017

By Antonio Fabiano de Oliveira

The aim of the present research work is to study the influence of hard chrome covered skin pass cold rolling rolls using 2D/3D surface topography, i.e. roughness characterization. The common stochastic structure Shot Blast Texturing (SBT) does not meet all requirements related to the production line regards to the finished product. The Hard Chrome layer, applied on these SBT rolls, can improve the sheet surface quality and is of fundamental interest mainly for those steel mills that do not have another alternative to new surface structures such as those that may be provided by the EDT, LT, EBT, etc. methods. The function of the generated surfaces, obtained by these different methods is going to influence the tribological properties during the subsequent forming processes. On the other hand, they can increase the product final cost or require large investments to obtain such surfaces. The results here presented are in accordance with other recently published research work, showing that there is a relationship between these parameters, and that further detailed studies are needed.

Aug 17, 2017

By Nishit Patel

Development work on the use of plasma torches in blast furnace ironmaking was completed in the 1980s. The technology developers planned to reduce blast furnace coke consumption using electrical energy and large scale coal injection through the tuyeres. Since this time, Westinghouse Plasma Corporation has improved torch reliability with industrial experience in solid-waste-to-energy facilities, as well as metallurgical applications. As coke makes up one-third of the hot metal cost, savings efforts frequently seek to lower coke consumption by increasing process efficiency or replacing coke with cheaper fuels. Alter NRG and Hatch assessed the merits of using plasma torch technology to superheat the hot blast. Coke rate savings, electrical purchase requirements, and a financial analysis to implement the torches are presented.

Aug 17, 2017

By Yasser Ghobara

Phosphorus is a problematic impurity that has challenged steelmakers for decades. Steel producers have developed specific technologies to eliminate phosphorus prior to and during steelmaking. These process technologies reduce phosphorus to various degrees and increase the cost of making steel. The state-of-the art dephosphorization technologies are described and operating costs compared for each of the established technologies. Costs are discussed in terms of price penalties for high P iron ore and selling premiums for low P steel. From this, strategies to control P in a cost effective manner are described.

Aug 17, 2017

By Theodore James Kurela

Analysis of adverse technical issues has traditionally relied on a snapshot of the state of the operation complemented with both the melt shop’s archived data and eyewitness accounts of adverse events. The GrafTech ArchiTech System is helping EAF shops solve problems faster by combining continuous analysis of information with statistically based alerts of process deviations. After one year of system implementation, a number of cases have been detected and communicated to melt shops worldwide. The objective of this paper is to examine a few of these cases; the early detection, statistical analysis, deviation reporting and the resulting countermeasures implemented.

Aug 17, 2017

By Mariano de Córdova

A operação dos altos-fornos com injeção de carvão pulverizado ou gás natural requer uma alta qualidade do coque. Para um custo mínimo do coque, mantendo a qualidade necessária, a escolha de carvões e a formulação da mistura é um tema muito importante. Uma ferramenta amplamente utilizada para o design de misturas é a modelagem, precedido pela caracterização de carvões e seguido de teste no forno piloto. Neste trabalho, revisa-se o desenvolvimento dos modelos, com base la literatura pública. Três etapas cronológicas são levadas em conta, desde os anos sessenta até a atualidade.

Aug 17, 2017

By Jorge Madias

Los hornos eléctricos de arco han sido motivo de una aplicación dinámica de nuevas tecnologías en lo que va de este siglo. La preparación de la chatarra y el uso de materiales de carga alternativos han dado lugar a la concepción de nuevos equipamientos y experiencias en todo el mundo. Surgen nuevos conceptos para el precalentamiento de la chatarra, superando las limitaciones de mantenimiento y ambientales de los conceptos iniciales y mejorando su performance energética. El aporte de energía química para la fusión supera sus límites año a año, requiriendo el desarrollo de equipamiento capaz de una acción rápida y precisa con grandes caudales de gases y sólidos inyectados. Existen nuevas herramientas para eliminar los riesgos de seguridad en la plataforma del horno, haciendo uso de sistemas de enfriamiento más seguros y duraderos, robots, automación de la operación del agujero de colado, y puertas de escoria controladas desde el púlpito.

Aug 17, 2017

By Dusan Ilic

Conveyor system wear of belts and transfers attribute to a significant proportion of the maintenance costs and lost productive hours when handling hard abrasive ores at high unit rates typical of the iron ore industry. The recent growth phase has seen a rapid increase in mine and export capacity, with many new and upgraded plants operating at high throughput and utilisation. Subsequently, the industry has progressed to an optimisation phase, seeking to maximise production capacity and reduce maintenance costs with minimal capital spend. To support this, a programme of modifying designs was executed to improve conveyor transfer chute and belt life, which identified a need to challenge the industry practice for specification of designs to improve the functionality of the installed equipment. While acknowledging the importance of selecting the highest wear resistant materials for the intended application, this paper investigates design criteria related to decreasing conveyor transfer and belt wear. Of focus is a shift in the manner in which designs are specified, from specifications primarily governing geometrical constraints, to those meeting technical and functional requirements aimed at producing optimum geometry for a given set of material handling parameters. An assessment of transfer design criteria is presented.

Aug 17, 2017

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017