Search Documents

By James Coull, Brian Wilson, David Siddle

"In 2012, Golder Construction Inc. was awarded a Design-Build contract for the design and construction of an extensive, deep ground improvement scheme to support up to 20 metres (66 ft) high Mechanically Stabilized Earth walls and bulk earthworks required for the development of the proposed Kitimat Liquefied Natural Gas (LNG) facility at Bish Cove, British Columbia (BC). Utilizing Cutter Soil Mixing (CSM) to construct barrettes consisting of overlapping rectangular panels of in-situ cement-treated soils, a deep mixing scheme, covering an area of approximately 12,900 m2 (15,430 yd2) and comprising some 1645 CSM panels to depths of up to 30.7 m (101 ft), was developed to provide the required static and seismic stability for the LNG structures, and meet the project-specific performance criteria.CSM panels were constructed through varying thicknesses and discontinuous layers of fine-grained, very soft to soft marine deposits, and loose to compact sands, with occasional interbeds of dense sands and gravels. Panel completion criteria was based on soil response factors, as measured by the CSM equipment, with the design requiring a typical embedment of about 2 m (7 ft) into dense silty sand to sand and gravel to provide the required bearing. A total volume of approximately 73,900 m3 (96,660 yd3) of soil was treated with cement to consistently yield average unconfined compressive strengths exceeding 2.5 MPa (363 psi).This paper outlines the challenges associated with the construction and quality control of this large deep mixing scheme in highly variable geotechnical conditions at a remote location with barge-only access, and limited communication facilities. Specifically the paper will discuss the logistical challenges faced and solutions adopted for the project; equipment redundancy requirements for a 24/7 operation; the impacts of wear and tear, as well as variability in subsurface conditions on productivity; quality control processes adopted for the project, including the value of provision of an on-site laboratory; and materials handling issues, and their impacts on mix design and quality control."

Jan 1, 2017

By Donald R. Clark

"Drilled shafts are being used as foundation support for parabolic solar troughs at the Genesis Solar Project being constructed near Blythe, California. Three types of drilled shaft foundations are required for the project. At project build-out, there will be a total of 23,008 drilled shafts installed at the site. Preliminary designs for the axial and lateral capacity of the drilled piers were based on conventional geotechnical engineering methodologies and soil-structure interaction. The drilled shafts and subsurface conditions were modeled through the use of the computer program LPILE v6.0.Conducting lateral load testing of drilled shafts was considered appropriate to confirm or modify the geotechnical parameters used in the preliminary design. The lateral load testing program was conducted to provide site-specific test data that would allow the design engineers (both geotechnical and structural) to predict the actual performance and adequacy of the proposed drilled shaft foundations and improve the efficiency and hopefully reduce project costs.The lateral load testing was conducted within two solar fields at the site. Three pairs of drilled shaft foundations were installed in each field, instrumented, and laterally loaded to determine load-deflection response. A value-engineered option, proposed by one of the drilled shaft contractors, was also load tested. The results of the load-deflection data obtained in the field was used to modify the soil modeling used in the original L-PILE analyses and adjust the production drilled shaft lengths.Based on the results of the lateral load testing, the in-situ moduli of the subsurface soils were significantly increased over that assumed in the preliminary analyses. Based on the final soil-structure interaction analyses, the preliminary drilled shaft lengths were reduced by 2 to 2-1/2 feet. This resulted in an overall reduction of 55,654 feet of drilled shaft construction on the entire project, a savings of approximately 16.5% over the preliminary"

Jan 1, 2017

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017

By Timothy Nelson, Simon Burnworth

"The University of California’s new Berkeley Art Museum and Pacific Film Archive will showcase a collection of art and film in a facility that pairs an existing 1930s-era printing press facility with a new, architecturally unique auditorium wing. The centerpiece of this adaptive-reuse project is the existing 3- story art-deco Administrative Building, which will be integrated into the new museum and provide approximately 18,000 square feet of usable space. Degenkolb Engineers, as the shoring engineer of record, along with Condon Johnson & Associates Inc., the shoring contractor, worked together with general contractor Plant Construction Company to design and build a temporary structure to facilitate the complex retrofit, renovation, and expansion of the Admin Building. This paper will discuss the challenges faced by the design and construction team, the sustainable solutions implemented on the project, and the collaboration between teams to meet the unique constraints of the project and the site.INTRODUCTION AND PROJECT BACKGROUNDThe Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California Berkeley (UCB) campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home."

Jan 1, 2017

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By L. A. Cisternas, R. I. Jeldres, D. Calisaya

"Flotation of copper-molybdenum sulphide ores in seawater entails critical challenges such as selective recovery of molybdenite, effective pyrite depression, and reducing the lime addition required to reach highly alkaline conditions. It is essential that laboratory flotation tests aimed at solving these problems give reliable, reproducible results and indicate the correct approach for industrial operations. Rougher flotation of coppermolybdenum sulphide ores in seawater was investigated using two different cells: a modified Denver cell and a standard commercial cell. The effect of an organic reagent on the flotation performance was tested, and the fast/slow-floating model was used to describe the results. The modified Denver cell significantly improved the reproducibility of the flotation test results, due to technological enhancements such as the impeller being driven from below without a stator, which enables the whole froth surface to be scraped with a paddle at a constant depth and rate. Organic reagents are a promising alternative to inorganic reagents for depressing pyrite in seawater. However, further studies should be conducted to investigate their impact on molybdenite recovery, as well as to evaluate the possibility of depressing pyrite after molybdenite separation. The fast/slow-floating model was found to be appropriate for describing the flotation kinetics of the copper-molybdenum ores. The parameters are useful for comparing the performance at different conditions. IntroductionOwing to the increasing scarcity of fresh water, the use of seawater mining and mineral processing is becoming increasingly important (Cisternas and Moreno, 2014). Seawater can be desalinated by reverse osmosis, but this involves considerable costs, limiting it to the big mining companies (Akgul et al., 2008; Leidner et al., 2012; Ghaffour, Missimer, and Amy, 2013). Furthermore, desalination has environmental consequences (Lee, Arnot, and Mattia, 2011); for example, a desalination plant designed to process 2.5 m3/s requires an electrical energy supply of around 30 MJ/s. To supply this power demand, a thermoelectric plant burning bituminous/sub-bituminous coal mixtures at a thermal power generation efficiency of 35% might release around 1200– 1500 t of CO2 per day. Furthermore, the effluents from desalination plants are typically discharged into the sea, and their high temperature and ionic content inevitably modifies the marine environment, with unknown consequences. The direct use of seawater is, therefore, more attractive, but it also poses major challenges since seawater contains ions that adversely affect mineral recoveries. In particular, in the flotation of sulphide ores in seawater, the floatability of molybdenite is depressed (Castro, 2012; Laskowski, Castro, and Ramos, 2014)."

Jan 1, 2017

By M. Nusheh, C. Bumby, A-H. Puichaud

"Vanadium-bearing titanomagnetite ironsand deposits occur along a 480 km stretch of the west coast of New Zealand. In the present study, the leaching behaviour of NZ ironsand was investigated in hydrochloric acid (2–10 M) solution at 50–80°C for 2 h. The resulting leaching liquors exhibited Fe/V ratios in the range 150–180. The distribution of trace element contaminants between solution and solid residue was investigated, and processing conditions have been determined for rapid and efficient dissolution of Fe, Ti and V into the leaching solution. In addition, mineralogical analysis of raw ironsand and leached residues was performed in order to study the leaching mechanism. Samples were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy (EDX), X-ray fluorescence spectroscopy, qualitative and quantitative X-ray diffraction and inductively coupled plasma mass spectrometry (ICP). Results indicate that the dominant dissolution process follows shrinking particle mechanism. However, ironsand particles containing ex-solution lamellae exhibited a different leaching behaviour compared to homogenous titanomagnetite particles.INTRODUCTION Titanomagnetite ironsand (blacksand) forms Quaternary onshore beach and dune deposits and offshore marine deposits (Figure 1) along 480 km of coastline from Kaipara Harbour south to Wanganui on the west coast of the North Island (Christie, 2016). It attracted the attention of scientists from the earliest times (Galbreath, 1998). The principal minerals in ironsand are titanomagnetite (TTM), ilmenite, quartz and ferromagnesian minerals such as augite, hornblende, diopside, and olivine with smaller amounts of rutile and apatite (Mauk, 2016).Several large ironsand deposits have been discovered and exploited since the late 1960’s. The Waikato North Head and Taharoa mines are currently operating and they have a 2015 measured resource of 400 million tonnes in total and provide over 2 million tonnes of concentrate per year by simple cost effective magnetic separation process (Christie, 2016; Christie & Brathwaite, 1997). The concentrate contains not only 7–8% TiO2 and 56–60% SFe, but also 0.3–0.6% V2O5, is both a valuable titanium mineral and a source of vanadium. All the production is used for steelmaking industries. The other potential for utilizing more of this resource without requirement of integration into an iron and steel producing plant is to develop a hydrometallurgical route with advantages of higher efficiency along with lower emissions. Currently, there is no existing commercial process capable of extracting all three of these elements as industrial-grade commodity products. Acid leaching of TTM concentrate with higher degrees of recovery and selectivity is a key step in any possible hydrometallurgical route."

Jan 1, 2017

By M. B. C. Brandt

The near-surface wave attenuation factor k (kappa), which describes the attenuation of seismic waves with distance in the upper 1–3 km of the Earth, was determined for the Far West Rand gold mining area using seismic data recorded by station Parys (PRYS) of the South African National Seismograph Network. Twenty micro-events in the magnitude range 0.7 ? ML ? 1.8 for the period 1 July to 15 November 2015 were analysed. For the analysis a 10-second window for the S phase portion of the vertical component seismogram was selected. The result was an average k = 0.048 ± 0.014 s, which is much higher than for a stable continental region where k = 0.006 s. This is because the assumed Brune source model is inappropriate for describing mining-related events that often have moment tensors with a volumetric (implosive) component. The average k was calculated to be 0.098 ± 0.038 s for explosions of a similar magnitude. This higher value derived for mining-related k may be employed as a means of correcting the Brune source spectrum to calculate seismic moment as well as corner frequency for events in the mining areas of South Africa.

Jan 1, 2017

By J. Girard, V. Aubé, M. Barakate, S. Bellec, M. R. Eddahabi, Y. Chaik, M. Deshaies

"The activated carbon used in the carbon-in-leach (CIL) process to absorb gold is subject to breakage. This carbon breakage can be minimized, but it will always be necessary to deal with fine carbon particles, known as carbon fines. These fines contain a significant amount of gold and mining operations generally struggle with the treatment of this product. Since IAMGOLD’s Essakane mine is located in Burkina Faso, shipping carbon fines out of the country was not considered a viable solution due to the logistical burden and legal procedures in place. A benchmarking study demonstrated the complexity of treating carbon fines on site. IAMGOLD partnered with the host government to find an innovative approach to economically recover the gold locked in these fines. This paper describes the new circuits commissioned in July 2016 built to improve carbon fines collection, incinerate the carbon fines and leach the gold in the ashes produced by incineration. These new circuits successfully demonstrate that it is possible to extract more than 94% of the gold content in the carbon fines. This is profitable for the company as it improves the overall mill recovery rate by 1.0% to 1.5% and significantly decreases gold inventory build-up on site.INTRODUCTION The activated carbon used in the carbon-in-leach (CIL) to absorb gold is subject to breakage. This breakage can occur in the CIL tanks, the stripping circuit, the regeneration process or anywhere throughout the pumping and handling processes of carbon through the circuit. Fine carbon particles are invariably created and, because of their small size, present a large specific surface which favors gold absorption (Hilsher et al., 2014). At the very beginning of operations at Essakane, the carbon fines were recovered by means of a thickener and a filter press, but the circuit was undersized and inefficient. Subsequently, a decantation basin was used to settle the fines before the thickener. The settled fines were shovelled from the basin into bags. All these bags were stored in the backyard of the plant. The average tonnage of carbon fines recovered monthly was 23.5 tons with a gold grade at 1938 g/t."

Jan 1, 2017

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By Alice Y. Tseng, Dan MacLean

"Corrosion protection of all deep foundation systems made of steel is THE issue when considering durability of the element in the long term. Protecting steel from corrosion and maintaining the steel tendon cross sectional area ensures a competent and durable system. The foundation of a building is usually difficult to repair and therefore high risk is taken when unknowingly choosing a non-adequate solution.Requirements according to EN 1990 (Eurocode 0 or EC 0) on construction durability requires a service life over 100 years. How can a service life over 100 years be achieved? How shall bare steel be protected in soil, which sometimes could be an aggressive environment to the steel? Which corrosion protection methods are commonly used in Europe and in North America?This paper will focus on hollow bars used as Micropiles, Anchor piles and Soil Nails. It gives an overview about the state of the practice in regards to corrosion protection (including head construction) and evaluates different options following the European Standards focusing on type of material and method of installation. Further the different corrosion protective methods such as thickness of grout body, coating types and sacrificial loss are listed with the pros and cons evaluated.Based not only on North American standards like FHWA “Micropile Design and Construction Guidelines”, FHWA Geotechnical Engineering Circular No. 7 for “Soil Nail Walls“ and Post-Tensioning Institute “Recommendations for Prestressed Rock and Soil Anchors”, but also European standards like EN 14199 “Execution of special geotechnical works – Micropiles”, EN 14490 “Execution of special geotechnical works - Soil nailing”, EN 1537 “Execution of special geotechnical work – Ground anchors“, and other relevant standards, all possibilities of protecting the hollow bars and the steel quality will be introduced, discussed and compared ."

Jan 1, 2017

By R. Venugopal, V. K. Saxena, S. K. Tripathy

"This study was carried out to understand the impact of variation in material morphology on the efficacy of microwave pretreatment. Three different types of mineral matter – coal, iron ore and manganese ore – were treated with microwaves at different energy levels, from 180 to 900 W, for different time durations of one to five minutes. The treated samples were subjected to microscopic, milling and liberation studies. Coal is a porous and amorphous material with low dielectric constant, and grinding of the microwave-pretreated coal samples resulted in an 18.18 percent reduction in the 80 percent of passing particle size, or d80, and a 17.1 percent increase in carbon recovery. The microwave-pretreated soft and friable manganese ore samples showed a 47.82 percent reduction in d80 during grinding and higher manganese recovery of 42.46 percent during liberation analysis. The microwave pretreatment and milling of hard and banded iron ore reduced the d80 by 20.83 percent, but no improvement was observed in mineral liberation. Coal showed better results during treatment at lower energy levels of 180 W for one to three minutes, whereas the minerals needed higher energy of 900 W for five minutes. Particle size analysis indicated rapid size reduction up to an energy input of 25 Wh. This effect diminished with increased energy input.IntroductionComminution is an important unit operation in mineral processing plants for the purposes of size reduction and mineral liberation. But most comminution technologies are energy inefficient and only a small amount of energy is consumed in real size reduction, with the rest wasted. High-grade mineral resources have been exploited on a large scale for the last century, and the upgrading of low-grade resources is now required to fulfill the needs of industry. Pretreatment methodologies for comminution will play a crucial role in the upgrading of low-grade mineral resources. Researchers have studied various pretreatment methods to develop an energy-efficient and techno-economically viable solution to improve mineral liberation and product fineness with minimum energy consumption. Most of these studies were focused on the use of chemical additives, thermal, ultrasonic and microwave treatment, and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Wilson et al., 2006; Kumar et al., 2010; Wang, Shi and Manlapig, 2011; Singh et al., 2012)."

Jan 1, 2017

By Brian E. Ladd

"A load test program was performed on two auger cast piles constructed in the Inner Coastal Plain geology of North Carolina. Both test piles were installed through Coastal Plain deposits and into underlying Piedmont residual soils; one test pile was embedded into partially weathered rock (PWR). The recommended 100-ton design load was confirmed by a test program that included instrumenting the piles with strain gages. The two piles performed differently during the load tests due to the effect of embedment into PWR. Loading Test Pile No. 1, which was not embedded into PWR, to failure at about 230% of the design compressive load allowed for evaluation of the mobilization of the ultimate shaft and end bearing resistances. Mobilization pile resistance was evaluated by comparing shaft and end bearing resistances to top of pile deflection (d) normalized by the pile diameter (D). For Test Pile No. 1, the ultimate average shaft resistance was achieved at d /D of about 7.5% and ultimate end bearing resistance at d /D of about 9.5%. Test Pile No. 2, embedded into PWR, achieved a d /D of only about 4% at 200% of the design load and was not loaded to failure. Shaft resistance was mobilized at a different rate within each individual geologic layer, i.e. ultimate shaft resistance did not occur simultaneously for all geologic layers. As the available total shaft resistance was exceeded and end bearing mobilized, the unit shaft resistances reduced from the peak values. A modified Davisson offset using d /D of about 6.5% appears applicable for evaluating the ultimate capacity of auger cast piles in the Inner Coastal Plain.INTRODUCTIONAuger-cast-in-place (ACIP) piling was developed in the 1940’s and patented in 1956 (Neely, 1991). Since patent expiration in 1973, ACIP piles are abundantly used in the United States, particularly in the southeast. However, most literature addresses driven piles constructed in sand and clay with lesser discussion of drilled piles. Conventional design methodologies (a- method, ß-method, SPT or CPT correlations, etc.) are based on data derived from numerous projects in a great variety of geologies. O’Neil (2001) notes that there are significant levels of uncertainty in the “universal” databases as evidenced by coefficients of variation of 0.35 to 0.40 for geotechnical parameters (su, SPT-Nvalue, etc.) used to estimate pile capacities.There is a need to develop local databases developed from data obtained from load tests that measure shaft resistance and end bearing. This paper presents the results of load tests conducted on axially loaded auger-cast-in-place piles constructed in the Inner Coastal Plain geology of North Carolina. Shaft resistance, end bearing, and movements that initiated mobilization of these resistances are described. The information presented herein can be used to refine geotechnical correlations and parameters applied in auger cast pile design methodologies."

Jan 1, 2017

By Leo Panian, Ryan Nagle, Priyanshu Singh, Gina Carlson, Wayne Magnusen

"This case study presents the design and construction of an integrated foundation and ground improvement solution utilizing deep soil mixing (DSM) and micropiles. 270 Brannan is a midrise office building in San Francisco that straddles the historic shoreline that was reclaimed in the 19th century. Subsurface conditions include shallow bedrock inland of the historic shoreline, and steeply dipping bedrock overlain by 60 feet of compressible deposits and liquefiable fill on the bay side. Project challenges included mitigating the liquefaction and lateral spreading hazards, addressing settlement concerns in the fill and the bay deposits, developing a cost-effective foundation support solution, assuring satisfactory seismic performance, and addressing construction restrictions with existing adjacent structures.DSM combined with micropiles was identified as the most cost-effective solution for the ground conditions. The DSM panels act both as a liquefaction mitigation mechanism and a foundation support system. Resistance to seismic overturning is provided by uplift-resisting micropiles. The DSM-micropile solution allows the use of efficient conventional spread footing foundations, integrating isolated micropile groups to anchor the shear walls. Successful installation of the system relied on a program of field testing to validate the design and conformance with the design criteria.INTRODUCTIONThe regular grid of surface streets within San Francisco’s South of Market (SOMA) district provides little evidence of the geotechnical complexities that lie below. In the late 1800s, sand dunes, bedrock hills, cliffs, marshes, and mud flats were flattened and filled, concealing their locations and characteristics. The 1906 San Francisco earthquake and fire leveled many buildings in SOMA; new buildings were built after 1906 – often on top of rubble and debris from the structures that came before. Locally, the combination of natural geology and historical interventions can produce complex subsurface conditions that vary dramatically over short distances. This is particularly true at locations where tidal mudflats once met bedrock hills at the shore of San Francisco Bay.This case study describes an integrated foundation and ground improvement system implemented for a multistory “Class A” office building at a complex SOMA urban infill site. The system utilizes cement deep soil mixing (DSM) in combination with spread footings and micropiles to address a range of design and construction issues, including liquefaction and lateral spreading mitigation; consistency of earthquake ground motions; shallow foundation support; seismic uplift resistance; and avoidance of loading adjacent basement walls. The system was implemented by a technically-sophisticated owner through a process that included constructive collaborations between the project geotechnical engineer, structural engineer, general contractor, and specialty foundation and ground improvement contractor(s). The system is designed to cost-effectively provide a high level of seismic performance."

Jan 1, 2017

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-substitution with clays and organically bound. Rare earth minerals (REMs) such as monazite exist in coal and have a grain size less than 5 microns. Froth flotation was successful in concentrating REMs existing in a thickener underflow material derived from Fire Clay seam coal which contained around 300 ppm of rare earth elements (REEs). Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2300 ppm REEs. Using a laboratory flotation column, a concentrate containing around 4700 ppm of total REEs was produced equating to an enrichment ratio of 10:1. INTRODUCTION Rare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets, and batteries [1, 2]. REE recovery from alternative sources such as coal and coal by-products has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials. The average REE content of the world coal is around 60-70 ppm [2]. There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia (300-1000 ppm), the Fire Clay coal seam in eastern Kentucky (500 ppm), and the Sydney Basin in Nova Scotia, Canada (72-483 ppm) [3-6]. The occurrence of REEs in coal and coal by-products can be classified into three types, i.e., rare earth minerals such as monazite and xenotime, ion exchangeable REEs in clays, and REEs associated with organic matrix. The particle size of the rare earth (RE) minerals in coal and coal by-products is very small and normally in the micron and/or nanometer scales. The flotation technique, which is based on the surface chemistry difference, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime, and bastnaesite [7-11]. As such, flotation is a promising method for the concentration of REEs from coal and coal by-products. In the current study, rare earth flotation was conducted using the fine coal refuse generated at an operating coal preparation plant treating coal from the Fire Clay seam. REE concentration by flotation required an appropriate amount of grinding and control of the pH value while using typical collectors. Prior to RE concentration, release tests were conducted to evaluate the floatability of the recoverable coal and the REE distribution in the flotation fractions in the fine refuse. Mineralogy of the REE was studied using SEM-EDX."

Jan 1, 2017

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017