Search Documents

By Torsten Wichtmann, Jan Macheck, Frederik Broz, Patrick Staubach, Hauke Zachert

The majority of heavy or strongly loaded structures, for instance high-rise buildings, large span bridges or gas storage tanks are founded on pile groups. However, current design codes and guidelines do not provide a standard procedure for their design under lateral dynamic and high-cyclic loading arising from e.g. wind, temperature or earthquake loads. To establish appropriate design strategies, a better understanding of the pile-soil, pile-pile and pile-cap interaction is required. This paper is focused on finite element backcalculations of centrifuge tests on single piles and pile groups subjected to up to 500 lateral load cycles. For the finite element simulations, a special calculation procedure is applied, combining two kinds of constitutive models, a conventional (Hypoplasticity with Intergranular Strain extension) and a special highcycle accumulation (HCA) model. The parameters of the constitutive models are calibrated based on static and cyclic laboratory tests on the sand used in the centrifuge tests. The performance of the applied numerical procedure is evaluated based on a detailed comparison of the simulation results with the measured data from the centrifuge tests. Overall the applicability of the used numerical strategy for simulating the behavior of pile groups subjected to high-cyclic loading is shown.

May 1, 2022

By T. R. Kostecki, A. J. S. Spearing, A. Hyett, M. Gadde

Ground control research for underground coal mining has progressed significantly over the past several decades. With this progression, and the ability to analyze and model underground conditions, underground working conditions have significantly improved. In order to progress further, the behavior of roof support must be known and be adequately modeled, such that models can be used for support design under different geological and mining conditions. This paper discusses the results from a research project funded by the U.S. National Institute for Occupational Safety and Health (NIOSH) and undertaken by Southern Illinois University Carbondale and Peabody Energy. The research involved installation of active and passive instrumented bolts in mines, recording relevant in situ data and then attempting to model the behavior of the bolts as mining progressed. Such calibrated models could aid in design of roof supports under different geological and mining layouts and thus, hopefully, further improve rock related safety.

Jan 1, 2012

By J. O. Stephens

During the late 1940's and early 1950?s, the Westinghouse Combustion Turbine Division built and demonstrated a residual oil-burning locomotive on six eastern railroads. Plans were made to convert to burning pulverized coal, and a single combustor was operated at a full-pressure condition in the laboratory for about two years. During the mid-1960's to mid-1970's, there was considerable interest in coal-burning MHD and a combustor was developed which would also be applicable to combustion turbines. In the early 19801s, the BCR National Laboratory (BCRNL) became affiliated with the University of Pittsburgh, and a program was begun, supported by the Stare of Pennsylvania, to develop an all-purpose combustor for use with industrial and utility boilers and eventually with combustion turbines. In this paper, we review the work of almost 40 years, indicate our present position, and propose steps to be taken leading to efficient and environmentally acceptable power generation from coal, and specifically to coal-burning locomotives.

Jan 1, 1986

By K. Hardy

As part of Inco's $115 million Fluid Bed Roaster SO2 Abatement Project, a new weak acid treatment plant (WATP) was constructed to treat bleed solutions from the Copper Cliff Smelting Complex gas-cleaning circuits. The WATP produces an iron-arsenic co-precipitate, termed "basic ferric arsenate" (BFA), which requires disposal in an environmentally acceptable manner. Following analysis of many potential options, the short-listed disposal alternatives were: A) Co-disposal of the BFA?gypsum sludge with rock tailings, a portion of which would be used in mine backfill, with the remainder being sent to the tailings area, and B) Co-disposal of BFA?gypsum sludge with pyrrhotite tailings in the tailings area. Testwork showed that the addition of BFA?gypsum sludge to mine backfill samples increased the uniaxial compressive strength (UCS) of the backfill for most samples, especially those at lower binder content ratios. Extensive analysis was conducted on samples taken from the Copper Cliff tailings area, where BFA?gypsum sludge from Inco's Copper Refining Electrowinning Department has been co-deposited with pyrrhotite tailings since 1990. Pore water samples from these areas contained very low arsenic concentrations, indicating that the arsenic had remained stable in that environment. Ultimately, co-deposition with pyrrhotite tailings was chosen as the preferred option for the disposal of BFA?gypsum sludge from Inco's new WATP.

Jan 1, 2006

This report contains the papers presented at the Technology Transfer Seminar on Ground Control Aspects of Coal Mine Design held by the Bureau of Mines on March 6, 1973, in Lexington, Ky. Seminar attendance consisted of representatives from the coal mining industry, universities, mining consultants, instrument manufacturers, and local, State, and Federal Government. The purpose of this meeting, one of a series of Technology Transfer seminars, was to provide the coal mining industry with detailed information about recently developed techniques, equipment, and instruments which can be used in the solution of coal mine design problems and to discuss results and direction of research in mine design. The report includes opening remarks by Joseph J. Yancik, Acting Assistant Director--Mining; an overview of the Federal Bureau of mines approach to mine design; three papers an problems associated with the design of panels; five papers on coal mine roof problems; three papers on long wall problems; and the comments made by- the participants on the Bureau-industry panel discussion.

Jan 1, 1974

By Donald L. Siebert

This profile study of the commercial secondary aluminum industry examines not only the elements that form the industry but also the technological contributions of each toward industrial growth. Concise descriptions of processing methods trace aluminum scrap from generating sources to marketable industrial and consumer goods. Economic and marketing appraisals are used to illustrate the impact that recent technology has had upon the secondary aluminum industry. Price, supply, demand, competition, and substitutes are selected as components of an economic model of the secondary industry and are used to illustrate the aggregate effects of technological changes. The final section is a conceptual look at the future in which sensitive economic indicators (such as die casting in the automotive and appliance industries) are examined as well as the problems of conserving mineral resources by retrieving secondary aluminum from solid waste.

Jan 1, 1970

By A. H. WHITE, PERRY BARKER

In a consideration of the various means whereby more economical and more efficient use may be made of the fuels in the United States, the possibility of obtaining for the production of illuminating gas other and cheaper fuels than the Pennsylvania coals demands attention. For the Government, as well as for private corporations and the householder, there can be no more economical and efficient way of using some coals than through the medium of illuminating gas. In the stove, gas reduces the labor cost of heat production and lessens the drudgery of the kitchen; burned in the Welsbach mantle, it is an excellent and cheap illuminant. In addition, the coke that remains after the gas has been recovered furnishes a smokeless fuel that has about the same heating value as anthracite. Hence any investigations that will indicate how local coals through proper treatment may be substituted for the higher priced and rapidly vanishing Pennsylvania gas coals will bring about lower prices for both gas and coke and will also aid to conserve for use in metallurgical processes the coking coals of Pennsylvania and of ot,her States. The annual drain on the gas-coal resources of this country and the importance of the gas and coke industries are indicated by the fact that 8,390,129 tons of coal were carbonized in retorts in the United States in 1909. The resulting salable products from by-product ovens were 15,791,220,000 cubic feet of coal gas, 6,254,644 tons of coke, and 60,126,000 gallons of tar. The total value of all by-products was about $28,508,637.

Jan 1, 1911

By R. K. Guthrie, H. B. Hill

"INTRODUCTION The Rodessa oil field in Marion and Cass Counties, Tex., Miller County, Ark., and Caddo Parish, La., was discovered in August 1930, when a well drilled to a depth of 5,506 feet in Caddo Parish, close to the surface trace of the Rodessa fault, produced gas in commercial quantities. During the next 5 years 21 gas wells were drilled, and a large reserve of natural gas was developed in the high part of the Rodessa structure underlying the Massive Anhydrite member of the Glen Rose formation.In July 1935 oil was discovered on the flank of the structure when a well drilled to 6,048 feet also in Caddo Parish, was completed as an oil well. The discovery of oil in the Rodessa structure initiated art intensive development program of more than usual interest to geologists, engineers, and operators in the petroleum and natural-gas industry. The complex nature of the different reservoirs, the large volume of ""free"" gas under high pressures and temperatures in the upper part of the reservoirs, and the high gas:oil ratios of some of the wells during the early production of oil presented many problems the solution of which taxed the ingenuity of those responsible for the development and exploitation of the Rodessa field.Early waste of gas and resultant dissipation of reservoir energy led to State intervention, which brought about effective regulation of the quantity of gas blown to the air. Oil production from wells producing more than 2.000 cubic feet of gas per barrel of oil was restricted, and oil allowables generally were based equally upon acreage and upon reservoir pressures. Consequently, oil-production statistics of the field are closely associated with gas:oil ratios and reservoir pressures.The primary object of this report is to present factual and statistical data on well performance in the Rodessa field and to show established trends under certain operating methods and practices in high-pressure gaseous reservoirs, which have been carefully developed and outlined by modern technique and exploited under close engineering supervision.The large size of the Rodessa field, it’s fairly well defined gas caps, and a somewhat definite water table in a part- of the oil- and gas-producing region are of special interest and importance in a study of the fluid and energy relationships in reservoirs. Consequently, the results of much of the authors' work in collecting and compiling date are presented in the form of tables, maps and cross sections to show the relative thicknesses of the different oil-and gas-producing members and their permeability and porosity relationships, and, when possible, the variations in stratigraphy are exhibited in cross sections. Results of a detailed analysis of cores from a number of wells also are presented in tabular and graphic form."

Aug 1, 1943

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

Accurate geometric models of orebodies establish the framework for reliable mineral resource estimates that provide a basis for further exploration and mine planning, as well as for financial models that ultimately determine the economic viability of a deposit. Traditional, explicit geometric modelling techniques that are utilised for resource modelling by the general mining software packages, such as MineSight«, involve manually digitising interpreted ore outlines that must be carefully linked to create valid geometric solid models. An alternative, implicit modelling method, employed by LeapfrogTM software relies on a fast method of global interpolation, which offers several advantages over traditional modelling techniques. Although previous case studies have documented the relative efficiencies of the two approaches, the accuracy of the two methods has not been previously quantified and compared. This study quantifies the accuracy of solid models created using explicit and implicit methods, and compares the differences between the models. Solid models of the Doris Hinge vein gold deposit (located in the Hope Bay district, Nunavut, Canada) are constructed from preliminary and follow-up drilling data using both modelling techniques. The accuracies of the solid models generated using preliminary drilling data are determined by measuring the 3D distance between the surface of the models and the actual contact location defined by the follow-up drilling data. Additional comparisons based on volume, cross-sectional area and surface differences were made between both phase 1 solid models and solid models constructed from phase 2 drilling information. The overall results of this study find that the MineSight« and LeapfrogTM solid model accuracies are virtually the same, and that their volume, cross-sectional area, and surface differences are comparable. This study concludes that the implicit modelling technique generates accurate solid models that can be used in place of explicit models as ore shells for resource estimation in certain circumstances.

Jan 1, 2006

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By J. R. Emery, D. F. Coates

"FOUR PAPERS ON CEMENTED BACKFILL were given at the Annual General Meeting of The Canadian Institute of Mining and Metallurgy in 1970:Weaver, W. S., and Luka, R., ""Laboratory Studies of Cement-Stabilized Mine Tailings"".Pasieka, A. R., Beattie, H. F., and Espley, G. H., ""Cemented Hydraulic Backill within the Falconbridge Group of Companies"".McLeod, P. C., and Schwartz, A., ""Consolidated Fill at Noranda Mines Limited (Geco Division)"".Clement, W. P., and Sokoloski, R., ""Pumping Cemented Backfill"".These four papers give the impression of a development in mining technology that has been substantially completed. Somewhat over ten years ago, The Inter-national Nickel Company of Canada, Limited and Falconbridge Nickel Mines Limited started experimenting with the addition of Portland cement to mill tailings to produce improved backfill and cheaper floors for scraping. Shortly after, the Canada Cement Company Limited (now Canada Cement Lafarge Ltd.), with full support of the two mining companies, started an extensive research program to provide the technologic-al data necessary to exploit what was obviously going to be a significant development in mining technology."

Jan 1, 1970

Discussion, at the Virginia Beach Meeting, February, 1894, of the Paper of Prof. Posepny. (Trans., xxiii., 197, 587.) Including communications subsequently received. a T. A. Rickard, Denver, Colorado (communication to the Secretary) : The paper of Professor Posepny was printed so short a time

Jan 1, 1895

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By Shillabeer J

Paste backfill has been adopted by many underground mines in North America and a growing number elsewhere. Paste offers a number of advantages. This paper suggests wider applications of paste technology to surface tailings disposal and water management. Advantages include improved overall stability, potentially easier permitting, smaller water inventory and earlier reclamation. It may be feasible to use the same plant to prepare backfill and to dispose of surplus tailings. Example cost models are given to illustrate potential applications.

Jan 1, 1998

By I B. Miller

Magnesium International Limited (MIL) has broken new ground in their desire to integrate their mineral development activities in the Southern Flinders Ranges of South Australia in to the communities of the region, despite there being no statutory requirement to do so. In their efforts to define a magnesite resource adjacent to the proposed site for a magnesium metal processing facility, MIL opened their exploration program up for public consultation. In conjunction with the Port Pirie Regional Development Board (PPRDB), a community group was formed to review the impact of exploration and mining on the ecologically sensitive Southern Flinders region. This voluntary move towards full community consultation for mineral exploration was a first in South Australia and probably in Australia. The Community Focus Group (CFG) worked closely with MIL, Primary Industries and Resources of South Australia (PIRSA) and the Department for Environment and Heritage (DEH) in the development of an exploration program and Declaration of Environmental Factors (DEF) acceptable to all stakeholders. Collaboratively, the community concerns were discussed and addressed, with the community gaining a very comprehensive understanding of the exploration process and possible future mine development. A balance of social, environmental and economic factors was developed that was accepted by all parties and encapsulated in the final DEF for approval by the regulatory authority. The consultation process was a new experience for all of the stakeholders, each of them effectively exploring new ground in addressing information dissemination, risk management and the social versus economic equation. MIL developed not only a viable and acceptable exploration program but also substantially reinforced its position as a responsible corporate citizen with the Southern Flinders communities.

Jan 1, 2004

By J R. O Walli

Large production shafts can be successfully sunk through the ubiquitous Blairmore formation of southern Saskatchewan by employing the freezing process and by the installation of a cast iron tubbing lining. Although the freezing technique for shaft sinking and the use of cast iron tubbing to preserve the shaft are new to the North American continent, these procedures have been employed in Europe for the past eighty years. More than 200 shafts, covering a wide variety of ground conditions, have been sunk by the freezing process, and most of these have been lined with cast iron tubbing. The No. 1 shaft of International Minerals and Chemical Corporation, near Esterhazy, Saskatchewan, comprises the first major example in Canada of the employment of European methods to overcome extremely difficult ground conditions. The Blairmore formation was solidified by the deep freezing process, employing a lithium chloride solution as the refrigerant, with input temperatures ranging to -55°F

Jan 1, 1964

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By W. C. Phalan

"Prewar Conditions:Metallic magnesium may be considered a war metal, but a war metal with a future, so far as the industry in the United States is concerned. Its production in the United States prior to 1915, on a commercial scale, was negligible, but imports prior to that year may be taken as a gaze of the demand for the metal. Unfortunately, magnesium was not listed separately by the Department of Commerce prior to the war, among the importations, but was included with other metals, as follows: ""Barium, calcium, magnesium, sodium, and potassium, and alloys of which said metals are the component materials of chief value."" However, the imports of metals enumerated other than magnesium were probably small, so that the importations under the above caption may be considered chiefly metallic magnesium in one form or another and, therefore, is an approximate gage of the demand for the metal in the United States. These imports were as follows:These figures are so close that they give a good idea of the figures for the respective calendar years.Of this prewar use, it has been estimated that about 85 per cent was used annually and in approximately equal quantities in the production of (1) flash-light powder, (2) fire works, (3) aluminum casting work, and (4) nickel and nickel-copper alleys, such as monel metal, etc. The re¬maining 15 per cent was employed for general uses, such as deoxiding brass and other copper alloys in foundry work, and to a small extent in laboratory and research work."

May 1, 1920

By D Howe, J Conn, J G. McLellan, K Gates

The Red October Gold Mine, owned by Saracen Gold Mines Pty Ltd, is located approximately 80 km south of Laverton, Western Australia. It is considered to be of a similar nature to many of the Archaean granite-greenstone deposits in the Laverton Tectonic Zone, and presents as an intriguing and relatively young deposit in terms of developed structural and genetic models. Regional deformation events have been proposed for the area, and are relatively well accepted. The most important of these deformation events in the region were the D4b (WNW–ESE sinistral transpression) and D5 (ENE–WSW dextral transpression) which have been attributed to the main Au mineralising phases. At the local scale there appears to have been a rotation of the regional stress field to provide the optimum orientation of maximum principal stress for sinistral movement on the main shear zone.Fully coupled 3D finite element analysis (FEA) was used to simulate the geomechanical response of the system based on structural observations. The geomechanical modelling resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two main deformation events. The D4 simulation provided a good correlation with the known distribution of subsidiary structures on the main shear zone, and furthermore provided several geomechanical targets that suggested locations of additional subsidiary structures. The D5 simulation provided a great insight into the response of the main shear zone and known subsidiary structures also highlighting additional targets indicating potential for further mineralisation. These targets have since been followed up with a 732 m deep surface reverse circulation (RC) drill hole, resulting in the discovery of two high-grade shoots, with follow up testing currently planned for mid-2014.CITATION:McLellan, J G, Conn, J, Howe, D and Gates, K, 2014. Structural controls and strain partitioning in the Red October Gold Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014