Search Documents

By Allen D. Graham

The coal industry in South Africa is briefly outlined. Test- work carried out on bulk samples of coal in the laboratory and used in the design of the Van Dyks Drift washery are described. Factors affecting the selection of equipment and the designed capacity of the plant are discussed. A description of the crushing plant, washery and load out section is given together with performance data obtained in the final acceptance tests. New features incorporated in the Van Dyks Drift plant and in more recent plants of the Group are outlined.

Jan 1, 1982

By V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pet natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pet of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 11 a in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F.

Jan 1, 1949

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By R. R. Allen

Gieseler plastometer tests were performed on eight western coking coals at retort - immersion depths ranging from 2 to 3-3 /4 inches (measured to the center of the coal charge ) . Increased maximum fluidities were associated with greater retort - immersion depths , the most pronounced increases being observed on highly swelling coals when tested at 3-3 /4 inches . The maximum fluidity of one of these coals when tested at 3-3 /4 inches was 146 percent greater than that observed at 24 inches . Retort - immersion depth had no significant effect on the temperatures of initial softening , fusion , maximum fluidity , end of fusion , and solidification .

Jan 1, 1964

By G. Roberts, S. S. Klima, W. R. Reed, J. Deluzio, G. Ross, A. Mazzella

The abstract discusses the problem of silicosis among roof bolter operators in coal mines due to respirable quartz dust (RCS) exposure. It presents a study comparing a new wet box collection system to the traditional dry box system. The wet box system uses water to saturate collected material, reducing RCS exposure during cleaning. The study found that the wet box system significantly reduced RCS exposures and quartz content in samples compared to the dry box system.

May 11, 2022

By Dodd SF

Valuation of mining companies and their underlying assets prepared by brokers' analysts are, by necessity, approximations. The reliability of the valuations is entirely proportional to the quality of available data, the reliability of forecasts and the nature of underlying commodity price assumptions. The latter is perhaps the greatest single cause of gross variations in company and asset earnings estimates and- valuations. Assumptions are often necessary regarding commodity price achievement based on commodity hedge positions. Public disclosure from listed companies provides a sound base from which to project earnings, cashflows and balance sheets. The uncommon disclosure of projected production and cost schedules often reduces the reliability of future estimates. The application of reserve and resource estimates is contentious with practitioners applying differing weightings to importance of resources in estimating mine lives (and therefore cashflow streams). Valuation methods applied in equity markets usually focus on relative value and the identification of pricing anomalies. The commonest ""rules of thumb"" applied in the valuation of mining companies (and therefore their underlying assets) is with the use of year specific price/earnings (P/E) and price/cashflow (P/CF) ratios, with low multiples suggesting undervalued assets, high multiples overvalued situations (but these rules can often be clouded by market expectations of underlying commodity price movements). Another simply applied valuation tool is to examine the examine the value placed on reserves and resources by the market. Inexpensive gold in the ground (expressed as $ of market capitalisation per ounce of reserves or resources) might indicate a buying opportunity, but the market does discount the value of gold in the ground prior to mine development and where development risk is perceived.

Jan 1, 1994

By W. Roggenthen, Z. J. Hladysz, G. D. Callahan, W. G. Pariseau, W. Weinig, C. Randolph-Loar, R. Popielak

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, SD, under the sponsorship of the U.S. National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments, including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4,850 ft) and 2.25 km (7,400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program, including preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations included geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By A. Nieto

This article is a review of previous discussions about underground mining method selection and classification with the purpose to clearly define and classify the two groups of variables (indicators) involved in the mining selection process: key deposit indicators (KDIs) and key mining method indicators (KMIs). This paper provides a simple and clear approach for the classification and selection of a feasible underground mining method based on a predetermined set of favorable deposit characteristics, which are defined as key deposit indictors (KDIs). This article also gives a summary of the key advantages and disadvantages associated with every underground mining method based on their key mining indicators (KMIs). The selection method given in this paper is based on defining field KDIs and comparing them to the KDIs that are favorable to every considered mining method. By cross validating a matrix of favorable KDIs, the paper presents a simple approach to rank several underground mining methods using a scale from favorable to less favorable accordingly to the ore deposit characteristics (KDIs). KMIs are used to further complement KDI rankings by analyzing every method’s KMI performance based on the expected productivity of the mining operation being considered. To further assist the reader through the selection process, this paper gives basic sketches representing each of the primary underground mining methods discussed in this paper. Each method is given using the same 3D isometric view as spatial reference to assist the reader with visual interpretation and comparison between methods.

Jan 1, 2010

By R. J. Gochin, M. A. Diaz

A modified Hallimond tube is described which allows the determination of the ultimate recovery R and the flotation rate constant k in a single, continuous experiment. The range of fine particles which can be satisfactorily floated with the modified apparatus can be extended by increasing the length of the bottom part of the tube. Findings suggest that pyrite and arsenopyrite can be separated in alkaline suspension using the so-called F series of collectors. Lime was found to act as a depressant. The collectors operate under pH and dosage control and do not require other depressants. Collectors used in the study were thio-amine (a cationic surfactant) and alkyl propionamide (a non-ionic surfactant)

Apr 1, 1995

By Joël P. T. Kapusta

Back in 1995, Air Liquide and Union Minière presented a joint paper at the Copper 95 – Cobre 95 Conference in Santiago, Chile, describing the first full scale plant trials of shrouded sonic injection in a Hoboken converter at the Hoboken smelter in Belgium. Almost a quarter of a century later, the technology known as ALSI, or Air Liquide Shrouded Injection, has been tested or commercially implemented in several copper and nickel smelters. Despite these successes, the copper industry did not adopt it widely in the same manner the steel industry adopted the Savard-Lee tuyere in the 1970s and beyond, not even in the way the lead industry adopted it with the Queneau-Schuhmann-Lurgi, or QSL, process. The development and implementation of bottom-blowing smelting and converting technologies in China in the last ten years, however, changed the industry’s perception that high- and ultra-high oxygen injection in copper smelting and converting was indeed possible under specific process conditions. In this paper, I retrace the key learnings of my journey with sonic injection over the twenty five years from my humble beginnings in my early years with Air Liquide, through plant trials and technology implementation in the late 1990s and into the first decade of the new millennium, and ultimately, to the most conclusive proof that the sonic injection design methodology I established is valid, and the calculation tools I developed are accurate. I conclude by sharing my thoughts about whether the deployment of the Savard and Lee legacy within the nonferrous industry was just a pipe dream or whether it will become a reality. INTRODUCTION In the context of lower quality ores and changing economic markets, copper smelters need to continuously innovate and improve to remain competitive and respect their corporate social responsibility engagements. One avenue towards this business, social, and environmental goal is to increase process intensity while lowering fossil fuel consumption to lower greenhouse gas emissions and reducing process off-gas volumes to better capture As and SO2–laden emissions. I believe high oxygen sonic injection for submerged tuyere copper bath smelting and converting is one technology that can help smelters achieve that goal of higher business, social, and environmental performance. Twenty five years ago, when I discovered that the Savard-Lee tuyere had revolutionized the steel industry (Savard & Lee, 1966; Knuppel, Brotzmann, Fassbieder, Savard, & Lee, 1972), I had a dream — or was it a vision? — that within the first decade of the new millennium, modern copper smelters operating submerged tuyere bath smelting and converting vessels will have implemented high oxygen sonic injection and will be reaping the financial and environmental benefits that the steel industry enjoyed in the 1970s. As we approach the end of the second decade of the new millennium, I have to admit that my dream has been all but shattered as the majority of copper bath smelting and converting vessels today continue to operate under bubbling regime conditions. This mode of operation is archaic, still requires tuyere punching and blows at inherently low enrichment levels, particularly in converting, producing large volumes of process off-gases. Under such operating conditions, regulations and emission quotas for As, SO2, and particulate matter oblige smelters to use not just primary or secondary hoods, but sometimes even tertiary hoods. I vividly recall being told, fifteen or twenty years ago when visiting smelters to promote the application of the Savard-Lee tuyere in nonferrous processes, that implementing sonic injection was not economically viable due to the high cost of compressing air and oxygen. Some of the smelters I visited back then have since mandated their engineering partners to design and build secondary or even tertiary hoods. I cannot fathom how secondary and particularly tertiary hoods, with all of their auxiliary equipment and added ducting, could be more economically viable than purchasing and installing a few compressors, expanding the pipeline network for compressed air and oxygen, and installing a new control valve train to feed sonic tuyeres. Besides, adding hoods does not address the problem of As and SO2-laden fugitive emissions at its source but merely provides a costly mitigation for it by capturing larger volumes of process off-gases rather than reducing these large volumes in the first place. Moreover, hooding does not reduce energy consumption nor does it increase process intensity, two aspects that I believe are critical for smelters to remain competitive and sustainable in a deeply changing market environment.

Jan 1, 2019

By M. Albertson

The purposes of this statement are to define a problem that exists in regard to the estimation of developed petroleum reserves, to analyze the problem in an abstract manner, and to discuss it as an introduction to certain papers that follow. The problem is to devise and develop a suitable procedure to permit more accurate estimates of developed petroleum reserves. Part of the problem is to make such estimates available earlier in the life of any particular pool. The problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became acute, some of the more prominent reasons being as follows: 1. The standard method of estimation depended on production-decline curves. This method is inapplicable while curtailment prevails and available methods arc insufficient. 2. The retarding influence imposed by wide open flow conditions upon overdevelopment is absent. Great losses of capital by overdevelopment can now occur before realization of the true situation occurs, or before effective steps can be taken to stop such wastage. This increases the need for early, accurate estimates. 3. Above-ground stocks have diminished and the equivalent of such supply tends more and more to be retained underground in the natural reservoirs. It becomes increasingly necessary to know accurately the amount of these stocks. To direct attention to an additional point of different nature: improved accuracy of reserve estimation can be obtained only by closer scrutiny of the factors that determine recovery. This examination and the resulting efforts to measure the effect of these factors in terms of ultimate recovery must tend to improve ultimate recovery. The statements regarding the acute nature of the problem also indicate to some extent the importance of the problem and the necessity of finding a solution. Developed reserves of the industry, and of individual opera-tors, are one of the great factors that properly should determine explora-

Jan 1, 1936

By M. Albertson

The purposes of this statement are to define a problem that exists in regard to the estimation of developed petroleum reserves, to analyze the problem in an abstract manner, and to discuss it as an introduction to certain papers that follow. The problem is to devise and develop a suitable procedure to permit more accurate estimates of developed petroleum reserves. Part of the problem is to make such estimates available earlier in the life of any particular pool. The problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became acute, some of the more prominent reasons being as follows: 1. The standard method of estimation depended on production-decline curves. This method is inapplicable while curtailment prevails and available methods arc insufficient. 2. The retarding influence imposed by wide open flow conditions upon overdevelopment is absent. Great losses of capital by overdevelopment can now occur before realization of the true situation occurs, or before effective steps can be taken to stop such wastage. This increases the need for early, accurate estimates. 3. Above-ground stocks have diminished and the equivalent of such supply tends more and more to be retained underground in the natural reservoirs. It becomes increasingly necessary to know accurately the amount of these stocks. To direct attention to an additional point of different nature: improved accuracy of reserve estimation can be obtained only by closer scrutiny of the factors that determine recovery. This examination and the resulting efforts to measure the effect of these factors in terms of ultimate recovery must tend to improve ultimate recovery. The statements regarding the acute nature of the problem also indicate to some extent the importance of the problem and the necessity of finding a solution. Developed reserves of the industry, and of individual opera-tors, are one of the great factors that properly should determine explora-

Jan 1, 1936

By S. M. Marshall, A. C. Richardson, H. Y. Yancey

A year ago, Marshall and Bird presented a paper in which a new method of measuring the agglutinating power of coal was described.' The procedure used was to determine the strength of a button containing 10 parts sand and one part coal, formed by carbonizing the mixture in a crucible in an electric furnace. The result of the determination was reported as the total weight in grams required to bring about complete destruction of the button. Correlations were shown between the agglutinating value and some of the characteristics of the different coals that were investigated. This agglutinating test has been in use fairly continuously during the past five years for coals of widely differing coking qualities, and it has shown reasonably concordant results accurate enough for commercial use, although there are many features of the test which should have further scientific study. During the past year a study has been made of some coals of low coking strengths, and incidental to the main investigation some data which appear to be of interest and value were obtained on the loss in agglutinating power caused by exposure to the air. Three coals were investigated, all of which were of the Tertiary age; two were from one field in Asia, and one from a field in the United States. The three were similar, as shown by the proximate and ultimate analyses in Table 1 (moisture-free basis). Coals SA and RA generally contain about 5 per cent. moisture and coal P about 3.5 per cent. moisture on the as-received basis. The large difference in the ash contents of the coals, amounting to practically 10 per cent. between SA and RA, and P, makes difficult a direct comparison of their qualities. In the second section of Table 1 the figures have been put upon an ash-free basis., This table shows that these coals are closely alike. The ultimate analyses are almost identical except for the higher nitrogen content of

Jan 1, 1930

By Charles E. Carlsen

Underground construction involves all the legal problems common to the construction industry and adds a nice little group of its own. Elements which will ultimately affect contractor-owner relationship commence to form almost as soon as the owner conceives of the project. A few of these with emphasis on their application to underground construction will be mentioned. (1) During the design stage, determination must be made as to whether the specifications will be general or restrictive. To what extent will the operations of the contractor be controlled? Can he proceed to use any method of tunnel excavation that he desires and only be responsible for the end result or will specific excavation procedures be required? Can explosives be used? Under what restrictions? Are tunnel supports required? How long can the crown behind the heading remain unsupported? What kind of supports are required? What restrictions on the placement of tunnel-lining concrete will be required? Each of you could extend this list for many pages but these illustrations are indicative of decisions that must be made in advance of bidding, and the ultimate decision on each question can have a significant effect on the legal relationships that exist between the contractor and the owner. The owner wants a good job at a fair price. On the other hand, nothing is worse than having a tunnel collapse during the construction period, with its extra costs, loss of life, and delay to the entire project. If the specifications are too restrictive, increased costs of performance are bound to occur. Owners save tremendous amounts of money by obtaining a contractor who has been ingenious in devising the most economical construction procedure. Care must be taken in drafting the specifications so that the benefits of such ingenuity will not be lost. (2) HOW is the contract to be awarded? Will there be open bidding, a restricted list of bidders, or will there be negotiations with a comparatively few contractors? If it is a government project, whether Federal, state, or

Jan 1, 1970

By A. H. Bell

The general principles of the gas-lift will not be described in this paper. Only specific details that have not been fully discussed in previous papers, or results that do not fully coincide with conditions previously described, will be dealt with. The principal points to be emphasized and for which supporting data are furnished are as follows: 1. Gas-lift installations usually have comparatively high efficiencies as compared with standard pumping equipment, when reduced to a basis of barrels produced per horsepower installed. 2. Advantages of high-pressure plants from the standpoint of operating efficiency and for the application of the gas-lift early in the life of flowing wells. 3. Evidence of increased ultimate yield through conservation of gas by the gas-lift. 4. Possibility of development of new equipment to increase efficiency of the gas-lift. 5. Indications of the advantages of repressuring as a means of stabilizing gas-lift wells and as a means of increasing ultimate yields. TyPes of Installation The gas-lift installations of the more important companies in California have been of the central-plant type wherever field conditions would permit. This has resulted in greater flexibility and lower installation costs per well than could be obtained with individual well units. In general discussions of the gas-lift method of production, the installation costs are frequently referred to as being too high for economical operation. If the field conditions are carefully analyzed and the plant designed with the idea of obtaining high operating efficiencies, the installation cost per well can be lowered sufficiently to compare favorably with individual well-pumping units, when the operating advantages are considered. Much greater production per horsepower can be obtained with the gas-lift than is possible with pumping equipment. Table 1 shows the unit sizes and costs of gas-lift installations of three companies in the Los Angeles basin. The cost of walking beams, rods,

Jan 1, 1928

By Eldon Dunlap

RECENTLY the producing branch of the petroleum industry has shown a considerable and growing interest in the quantitative determination of the water, oil, and gas content of cores as it relates to estimation of reserves, to providing a, basis for judging as to the feasibility of applying various secondary-recovery and pressure-maintenance processes, and in general to the operation of producing properties. For years it has been known that oil, gas and water coexisted in the pores of many semidepleted oil measures. It is now generally believed that oil-bearing beds contain connate water in amounts varying up to 50 per cent of the pore space. However, only lately has reliable direct evidence of the extensive occur-rence of connate water in oil sands been published. Very little work has been done to ascertain the effect of this water on the productivity and ultimate recovery of oil from wells. It was the intent of this research to study the influence of this indigenous water on the flow of oil through unconsolidated sands, with the hope that the results could be applied qualitatively to the flow of oil in underground reservoirs partly saturated with water. Obviously, ultimate recovery estimates based on the void volume of the reservoir will be in error unless a, conscious or unconscious correction is made for the volume of water occupying a portion of the effective pore volume of the reservoir- Evaluation engineers in the past have applied arbitrary saturation and recovery factors that may inadverently have compensated for the failure to consider specifically the water content. Nevertheless, the evidence available indicates that these factors need revising if each is to be independently correct and truly representative. Although the mere fact that the connate water renders part of the pore volume of the reservoir incapable of containing oil is of primary importance to the operator, it is also of interest to know whether and to what extent the presence of varying amounts of interstitial water influ-ences the permeability of the sand to oil.

Jan 1, 1938

By Joseph Kaye Wood

A metal is said to be overstrained when it is deformed beyond the elastic limit at a temperature well below the critical range, as in cold working. Quantitatively, overstrain might be considered as that part of the total elastic deformation of the piece of metal, left over after the external load is removed, that added to the permanent deformation due to plastic action will give the total permanent deformation. Ordinarily the effects of this phenomenon, which vary with the internal residual stress probably in accordance with Hooke's law, are more noticeable when the yield point of the metal is exceeded, but they probably also exist to a smaller degree when the load is just large enough to cause the least amount of permanent set. These effects, which we recognize as the result of overstrain, are as follows: 1. An apparent increase of the elastic limit in tension and a decrease of the elastic limit in compression, provided the external load is tensile. The reverse is true when the load is compressive. 2. An elastic after-effeet in which time and temperature are important factors. 3. A state of imperfect elasticity in which Hooke's straight line becomes slightly curved, giving rise to an hysteresis loop. 4. In addition to the apparent increase in the elastic limit, such properties as the hardness, ultimate strength, and resistance to fatigue failure are increased, provided the overstraining has not been carried far enough to make the metal brittle. 5. Correspondingly the ultimate elongation, reduction in area, magnetic quality, ratio of endurance limit (fatigue breaking stress) to elastic limit, and resistance to season cracking (in certain copper alloys) are decreased. The question naturally arises: how do these changes in the properties of a metal resulting from overstrain influence our method of design? The fact that most of the desirable qualities are increased makes overstraining a favorable process, from an engineering standpoint; but on the other hand, the loss of such qualities as perfect elasticity and complete

Jan 1, 1924

By Eldon N. Dunlap

Recently the producing branch of the petroleum industry has shown a considerable and growing interest in the quantitative determination of the water, oil, and gas content of cores as it relates to estimation of reserves, to providing a basis for judging as to the feasibility of applying various secondary-recovery and pressure-maintenance processes, and in general to the operation of producing properties. For years it has been known that oil, gas and water coexisted in the pores of many semidepleted oil measures. It is now generally believed that oil-bearing beds contain connate water in amounts varying up to 50 per cent of the pore space. However, only lately has reliable direct evidence of the extensive occurrence of connate water in oil sands been published. Very little work has been done to ascertain the effect of this water on the productivity and ultimate recovery of oil from wells. It was the intent of this research to study the influence of interstitial water on the flow of oil through unconsolidated sands, with the hope that the results could be applied qualitatively to the flow of oil in underground reservoirs partly saturated with water. Obviously, ultimate recovery estimates based on the void volume of the reservoir will be in error unless a correction is made for the volume of water that occupies a portion of the effective pore volume of the reservoir. Evaluation engineers in the past have applied arbitrary saturation and recovery factors that may inadverently have compensated for the failure to consider specifically the water content. Nevertheless, the evidence available indicates that these factors need revising if each is to be independently correct and truly representative. Although the fact that the connate water renders part of the pore volume of the reservoir incapable of containing oil is of primary importance to the operator, it is also to his interest to know to what extent the presence of varying amounts of interstitial water influences the permeability of the sand to oil.

Jan 1, 1938

By Sam Harlan

At intervals during the past several years the oil industry has been confronted with the problem of forestalling crises in its affairs. These crises have been reduced to periods of depression which, fortunately, the industry has been able to survive. Under the existing competitive practices which control the producing division of the industry it apparently has been proved that the best efforts logically to curtail development and producing operations are inadequate for effecting a true production balance and the consequent stabilization of prices. The industry is awakening to the fact that the situation warrants revolutionary thought and at this time it is looking for a permanent solution of its problem in a general plan for unit development and operation such as the one first proposed by Henry L. Doherty. Mr. Doherty's proposal was designed not only as a means for stabilizing the industry as a whole, but its principles involve very definite potential benefits for the average individual operator and royalty owner as participants in pooled projects. The benefits to these individuals would be derived from maximum recovery, the maximum utilization of natural energies, the minimization of development and operating costs, enhanced values of leases and royalties through improved efficiencies and ultimate yields, improved earnings through stabilized crude oil prices, etc. This plan was revolutionary to the industry's practices and at the time was rejected, but it now appears that the development and operating policies for new properties are continually approaching the ideal of the original plan. Oil companies are constantly extending their efforts to improve all factors that have a bearing on the costs and efficiencies of their operations. These efforts may, in some degree, be a normal outgrowth of the industry's progress, but the forced consideration of market conditions, the growing appreciation of the importance of regulating operations for maximum ultimate economies and the depreciation of the old principle of maximum flush at any cost, come from a new school of thought which has been stimulated by the immediate pressure of overproduction and

Jan 1, 1930

By Gerald V. Jergensen

Does an idea have merit? What does it cost to implement? Can the concept be implemented successfully? The ultimate proof is to try, then see. However, when there are many millions of dollars at stake, blindly building and trying requires considerable courage. Owners and investors in retrospect might choose other less complimentary words. So we might ask, "How might we establish the feasibility of an idea or concept before committing large sums of money to the ultimate test?" From this basic and prudent question, has evolved the engineering concept of the feasibility study. A feasibility study is simply a systematic evaluation of an idea or concept to determine the prospects for success. In a literal sense, a feasibility study considers an idea in terms of its data base, "builds" the idea on paper, "operates" that idea, calculates the cost and benefits, then measures the probable success in terms of some economic, technical or financial standard. Feasibility studies can be quite modest in scope yet provide useful insights as to the viability of an idea. A study might be initiated only to examine the completeness or validity of the metallurgical data base. Another study could be a search for a workable idea or solution to an already-identified possibly troublesome problem. In this latter case, the question, "Will it work?" may be far more important than, "How much will it cost?" Feasibility studies are sometimes global in scope, involving several dozens of specialists and examining an entire "grass roots" mining complex. Other studies may be less ambitious but equally important in examining an expansion proposal or developing new operating techniques. Studies may be commissioned to remove plant bottle-necks, solve maintenance problems and so on. The terms study and feasibility study are used interchangeably in this chapter. They denote a systematic method to examine a proposed concept or idea. DATA BASE Typically, studies are initiated with a minimum amount of specific information and a maximum number of assumptions. As the work proceeds and the data base expands, assumptions are replaced

Jan 1, 1982