Search Documents

By WL Wagner

This report presents a quality control approach to the derivation of strategies for monitoring a work environment; specifically, the environment in underground mines where diesel-powered equipment and blasting agents are used. The approach is presented as a series of 22 steps called the Monitoring Strategy Development Scheme. The scheme is an orderly method for selecting from a number of options a strategy or tactics to cost effectively meet the requirements of a chosen objective related to the monitoring of breathing zone air quality. The scheme provides a format to quantify many of the factors that influence the selection of on strategy or tactic over another, and to ensure that important considerations are not neglected. The premise that breathing zone air in work environment can be considered to be manufactured product and that, therefore, conventional quality control approaches are applicable, is introduced. Typical approaches to the quality control of manufactured products and how these approaches can be applied to the selection of monitoring strategies are discussed.

Jan 1, 1983

By Norma Golumbic

The primary purpose of the Bergius (hydrogenation of coal) and Fischer-Tropsch (hydrogenation of carbon monoxide) processes is the production of synthetic liquid fuels. This objective is of importance in insuring an adequate supply of motor fuels and lubricating oils in the United States. In the urgency of the basic research and process development work on synthetic liquid fuels, the possibilities for the production of synthetic chemicals inherent in these processes have hitherto received little attention in this country. However, the by-products, as well as the primary products, from the Bergius and Fischer-Tropsch processes are rich source materials for organic chemicals. The overhead oil from liquid-phase hydrogenation of coal, for example, contains benzene, toluene, xylene, cyclohexane, methylcyclohexane, aromatic solvents, about 20 percent tar acids (largely phenol, cresols, and xylenols), and 3 percent nitrogen bases. Wax, alcohols, and acids are by--products of the Fischer-Tropsch synthesis. In addition, techniques have been developed which make possible the production of aliphatic hydrocarbons, alcohols, acids, aldehydes, and other oxygenated organic compounds. These chemicals are more valuable on a unit basis than gasoline. Because of continued rapid expansion of the plastic, resin, lacquer, and solvent industries, larger amounts of many of these chemicals will be needed in the near future.

Jan 1, 1949

By R. A. Cattell

With the surrender of the Japanese Imperial Government as a climax to the capitulation of the German High Command , the main objective of the Petroleum and Natural Gas Division pivoted from war assignments to its main normal functions . One of these functions is to give wide public distribution to valuable technical facts which the Division has obtained through research on petroleum , natural gas , helium , and related subjects . During the war years many engineering data and scientific facts could be released only on a restricted basis as reports to war agencies and others immediately concerned . Moreover , many of the wartime reports contained masses of detailed data that were prepared under stress to meet emergency schedules . For peacetime publication and application , these data must be reviewed , correlated , and rearranged so as to present the essentials in proper form . To illustrate , a wartime report of 50 pages might be resolved into one curve in a composite graph for a peacetime publication . Another factor affecting the orientation of the work of the Division is the broader horizon of research revealed by its war activities . Fundamental research and careful engineering analyses are just as important in time of peace as in time of war; in fact , they should be more important to the forward view , because under peace conditions disrupting influences that distract from the orderly acquisition of knowledge are minimized . Therefore , the concerted effort has been not to " salvage " the results of the war activities , but to evaluate them on the basis of their relative importance in the future economy of the country . Where wartime investigations have pointed to peacetime accomplishments , the effort has been to give the corresponding type of work additional emphasis . This adjustment can not be made hurriedly , but many of the necessary preliminary steps on the new course have been taken ..

Jun 1, 1949

By James P. Kimball

Sulphur is always present in mineral coal of every variety. In the oxidized state it may exist as sulphuric acid in combination with a base. In the unoxidized state it exists in combination with iron as bisulphide of iron. It is also supposed by some chemists to exist in unknown combinations with the organic elements of the coal. This supposition requires the demonstration as a fact that certain coals yield more sulphur than what may exist in a free state, or what belongs to recognized combinations, not only with the accompanying iron but with other inorganic bases abundantly occurring in coals, but which unfortunately are very rarely estimated. This practically as well as theoretically important question it is at present impossible to decide, simply for want of available thorough ultimate coal analyses including the ash. Such analyses, at the best imperfect, are luborious and intricate, and therefore seldom made, the much simpler proximate analyses, so-called, being resorted to by most chemists for technical purposes, and commonly substituted for more scientific work even in the laboratories of government surveys. And it is unfortunate enough that few ultimate analyses are extended to the composition of the ash, much less to its relation to the original constitution of the coal. Sulphur chiefly occurs in most coals in the form of yellow pyrites (pyrite) and white pyrites (marcasite), both minerals, characterized by differences in crystalline form and in physical properties as well as in color, but having the same chemical composition (FeS2). No coal is entirely free from one or both of these dimorphous forms of bisulphide of iron. It may be disseminated through the mass so as to be invisible, in plates or scales between the laminæ of the coal, or in conspicuous segregations or nodules, sometimes of considerable dimensions. Coals greatly differ as to the proportion of sulphur which they contain. They also differ as to the relative proportion in which its several forms of combination occur. Such qualitative and qnantitative disparities arc scarcely, if at all, more marked in separate coal seams of a uniform type than in different parts of one and the same coal seam, whether it be considered locally as constituted of several

Jan 1, 1880

By James P. Dr. Kimball

SULPHUR is always present in mineral coal of every variety. In the oxidized state it may exist as sulphuric acid in combination with a base. In the unoxidized state it exists in combination with iron as bisulphide of iron. It is also supposed by some chemists to exist in unknown combinations with the organic elements of the coal. This supposition requires the demonstration as a fact that certain coals yield more sulphur than what may exist in a free state, or what belongs to recognized combinations, not only with the accompanying iron but with other inorganic bases abundantly occurring in coals, but which unfortunately are very rarely estimated. This practically as well as theoretically important question it is at present impossible to decide, simply for want of available thorough ultimate coal analyses including the ash. Such analyses, at the best imperfect, are laborious and intricate, and therefore seldom made, the much simpler proximate analyses, so-called, being resorted to by most chemists for technical purposes, and commonly substituted for more scientific work even in the laboratories of government surveys. And it is unfortunate enough that few ultimate analyses are extended to the composition of the ash, much less to its relation to the original constitution of the coal. Sulphur chiefly occurs in most coals in the form of yellow pyrites (pyrite) and white pyrites (marcasite), both minerals, characterized by differences in crystalline form and in physical properties as well as in color, but having the same chemical composition (FeS2). No coal is entirely free from one or both of these dimorphous forms of bisulphide of iron. It may be disseminated through the mass so as to be invisible, in plates or scales between the laminæ of the coal, or in conspicuous segregations or nodules, sometimes of considerable dimensions. Coals greatly differ as to the proportion of sulphur which they contain. They also differ as to the relative proportion in which its several forms of combination occur. Such qualitative and quantitative disparities are scarcely, if at all, more marked in separate coal seams of a uniform type than in different parts of one and the same coal seam, whether it be considered locally as constituted of several

Jan 1, 1880

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By Daniel H. Knepper

Estimating the lithologic composition of gravel deposits for aggregate quality using standard field and laboratory techniques is costly and time-consuming. As an alternative, digital geologic maps and elevation models may provide a means for predicting the lithologic composition of channel and terrace deposits. Digital geologic maps can be used to evaluate the distribution of map units: their geomorphic setting, and the physical properties of the gravel source. To test this concept, the lithologies and topography of the upper drainage basin of the Big Thompson River along the Colorado Front Range were used to examine various factors that may control the final lithologic composition of channel and terrace gravels downstream. The simplest factor is the area of each of the map units in the upper drainage basin area, which can be easily measured from the digital geologic map. The percentage of each map unit within the total area provides a estimate of the pro- portions of each map unit that might be expected to occur in the downstream gravels. Published estimates of the hardness and durability of each map unit were used to calculate physical property-weighted areas; these areas are an estimate of the potential of each unit to be eroded and transported as gravel-sized particles. The areas of each map unit at 1-kilometer intervals from the drainage basin exit point were used to calculate a distance-weighted area for each map unit. For this study, a simple inverse relationship (area/distance) was used for distance weighting, but a more complicated distance function may ultimately be required. The topographic setting of exposed rock units should exert a significant influence on whether material will move slowly or rapidly through the drainage system. Two topographic factors were examined: gradient and slope. A simple gradient between map unit occurrences and the exit point of the drainage basin was used to calculate a gradient-weighted area estimate for each map unit. The slope-weighted area estimate uses the slope steepness (in degrees) in the immediate vicinity of each map unit occurrence as a measure of the tendency of material to begin moving into the sediment transport system. The primary intent of this study was to test the concept of using digital geologic map and elevation images to estimate gravel composition, rather than actually producing a useful analysis of a drainage basin. Each of the controlling factors was examined independently to gain an understanding of the magnitude of the effect of each factor. Ultimately, a comprehensive predictive model will be constructed using a combination of the various controlling factors.

Jan 1, 2001

By C. M. Nickerson

In times of overproduction such as the operators have been struggling against for the past several years it is the practice of the oil industry to shut in certain wells in order to reduce the flood of oil. The purpose of this paper is to present certain variations in production of oil wells when the offset wells are shut in. The scope of the study has been confined to California fields, and more especially to those of the San Joaquin Valley. The accepted definition of a shut-in well is a well where production has been suspended by closing in the casinghead arid tubing or by cessation of pumping. The immediate effect of such a procedure, of course, is to reduce the oil production from the lease, which is the result desired. However, it appears that certain types of wells vary widely in production of oil, gas and gasoline after adjacent wells have been shut in, which variation has a very material effect on the ultimate recovery of oil from the property. The increase or decrease in the oil production itself may not be of sufficient volume to occasion comment, but wide fluctuations in the gas and gasoline recovery under the changed conditions arc of the utmost importance in the future recovery of oil. The scope of this paper includes: (I) the effect on producing oil wells of shutting in offset wells, the wells being studied in three groups arranged according to their relative stages of depletion; (2) probable source of excess gas and the effect on the ultimate recovery of oil; (3) suggested procedure when wells are shut in; (4) methods that could be employed to prevent undue migration of gas from the shut-in area; and (5) the need for future studies of the situation. Three Classes of Producing Oil Wells For the purposes of this paper producing wells in California have been arranged in three groups according to the age of the well, or to the relative stage of depletion of the producing zones. The first group consists of those wells with a high fluid level, or in other words those wells whose fluid levels are a considerable distance above the top of the perforations. This type of well is in the flush period of its life and ordinarily produces

Jan 1, 1929

By M J. Kelleher

CREAM is an acronym for coal recovery, evaluation, analysis and management and is a business improvement project at BMAÆs Goonyella Riverside mine that is focussed on maximising coal recovered. In August 2003, Goonyella Riverside was set a challenge to quantify coal loss and dilution and their relationship to cost, revenue and ultimately profit. While the mine was confident in its site forecasts of recovery (and loss), it was clear that the traditional measurement and analysis systems were inadequate to firstly, identify key loss areas and mechanisms and secondly, successfully quantify the benefit of various coal recovery initiatives. The path that BMA Goonyella Riverside has travelled to maximise coal recovered can be divided into four key steps: Mapping the process û This step involved the development of a coal flow process map for Goonyella Riverside that stepped through each component of the process from the coal reserve to the customer and identified key measurement points for the purposes of reconciliation. Understanding coal loss and identifying opportunities û This step involved conducting two detailed Reserve to Customer projects at the mine site to track a block of coal from the reserve to the customer and to gain a greater understanding of the relationship of dilution, coal loss mechanisms, revenue and costs associated with recovering additional coal. Coal data systems development û Two important coal data systems have been developed and implemented at Goonyella Riverside in the past twelve months, namely SnowdenÆs Coal Reconcilor and SeamFix. These systems enable coal losses and dilution to be quantified and reconciled back to the initial coal reserve. Implementation of loss reduction initiatives û This step involved the formation of a business improvement project referred to as æCREAMÆ in August 2004, for the purposes of improving pit coal recovery and maximising business value. To date a series of coal recovery trials have been run in a number of pits at Goonyella Riverside that have yielded significant improvements in business value. The key to the success of this project has been the discipline to follow a defined process map, management commitment through resourcing and shared key performance indicators, a successful acceptance strategy resulting in holistic ownership and the implementation of sustainable reconciliation systems. Coal loss and dilution are now quantifiable and their relationship to cost, revenue and ultimately profit is well understood. This paper discusses the process that Goonyella Riverside has adopted to maximise coal recovered.

Jan 1, 2005

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany's basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By AIME AIME

ANDREW FLETCHER, newly elected Treasurer and Director, has spent his entire mining career in the employ of the St. Joseph Lead Co. and brings to the Institute Board a career rich in financial experience and varied in interest and accomplishment. "Drew" Fletcher was born in New York City on Feb. 6, 1895. After graduating from the Sheffield Scientific School of Yale in 1916 as a mechanical engineer, he became a shipyard mechanic in Wilmington, Del. The next thirteen years saw. him gradually enlarging his responsibilities until he ultimately became the head of the W. & A. Fletcher Co., in Hoboken, N. J., ship repairers. In 1929 his program for merging the Fletcher plant with five other New York shipyards was finally consummated in the formation of the United Dry Docks, Inc., which subsequently was purchased by Bethlehem Steel, with the result that today the old Fletcher yard and organization has been expanded into one of the finest ship repair units in the United States.

Jan 1, 1944

By T. Hadley, E. Catovic

"Northern Minerals Limited’s (ASX: NTU) flagship project is the Browns Range Rare Earth Project (the Project) located in Western Australia, consisting of a number of deposits with high value, heavy rare earth elements, in particular yttrium, terbium, and dysprosium. The deposits are dominated by xenotime mineralisation, which occurs within hydrothermal silicified and hematitic breccias. The Company delivered an initial JORC compliant resource estimate for the Project at the end of 2012 of 10,500 t of contained total rare earth oxides (TREO), which was increased to 28,084t of contained TREO in October 2013 and further enlarged to 47,997 t of contained TREO in February 2014. Concurrent with the growth of the Project resource base, significant progress has been made in developing the metallurgical process for the beneficiation and extraction of rare earth elements (REE’s) from the xenotime mineralisation. Development of the beneficiation circuit evaluated several process options and selected whole-ore flotation and magnetic separation, followed by flotation (hybrid circuit) as the two preferred flowsheets to pilot, following encouraging results on the bench of 83% and 86% recovery to a 20% TREO mineral concentrate respectively. Several downstream hydrometallurgical extraction flowsheets were evaluated. However, the following two preferred process flowsheets were ultimately selected for further detailed investigation during the prefeasibility study: 1. Sulphation bake, water leach, purification, oxalate precipitation, and/or calcination to produce a mixed RE oxide; 2. Sulphation bake, water leach, phosphate precipitation, caustic conversion, HCl leach, and oxalate precipitation to produce a mixed RE oxalate. Excellent heavy rare earth oxide (HREO) extractions (~ 90%) from beneficiation concentrates were achieved on the bench for both circuits, however flowsheet 1 was ultimately selected as the preferred flowsheet to pilot due to lower capital and operating cost. A mixed rare earth oxalate (42% TREO) or oxide (92% TREO) can be produced with low levels of Th and U of 3 ppm and 6 ppm respectively."

Jan 1, 2014

By E. E. McGinley, L. D. Woodworth

DURING the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and plant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinability and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tinplate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. PHYSICAL PROPERTIES OF BESSEMER VS. OPEN-HEARTH STEELS A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from ¾ to 1 ¼ -in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. 1, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By Mohammad Hossein Sadaghiani

"Construction of underground structures in urban areas is a very challenging work. There are generally two methods of construction, an open cut-and-cover and underground method. To eliminate the subsurface and surface disturbance and street traffic problems, underground method is preferred. The stress redistribution caused by underground excavation induces movements and deformation in the earth mass and ultimately at the ground surface. This is more pronounced in large space excavations. Generally pre-supporting system is used to control ground deformation and thus enhance its stability. In this paper an innovative pre-supporting system is presented. Concrete Arch Pre-supporting System (CAPS) is introduced in Tehran Metro in 2002. This method has roots in construction method of an Old Iranian small water tunnels, called Quanat. CAPS is an efficient method for stabilizing large span underground spaces constructed in shallow and soft ground. In this technique underground reinforced concrete elements are constructed around the proposed underground space prior to main excavation. This method is used successfully in over 50 large span underground structures in Tehran Metro stations and road tunnel intersections. CAPS has potential to be used to pre-support the large span underground spaces at any weak ground condition in an urban area.1. INTRODUCTION Underground subway stations can be constructed either by open cut-and-cover or underground construction. Due to the presence of subsurface utilities and street traffics in urban areas, underground construction is preferred to eliminate relocation of the subsurface utilities, and other urban disturbance. Underground construction in an urban area is a very challenging effort. The complexity of the work is more pronounced in a weak and shallow ground. The stress redistribution caused by underground excavation induces deformations in the earth mass and ultimately at the ground surface causing damage to adjacent structures. The need to control ground surface settlements in urban area is widely recognized and new construction methods are continuously developed. Settlements induced by underground excavation may cause serious damages to nearby structures and subsurface underground utilities, (Sekimoto et. al. 2001). In order to improve stability of underground excavation and reduce settlements, various ground treatment techniques are presented, Johnson, et.al., (1983), Carrieri, et.al. (2002), and Ocak (2008)."

Jan 1, 2016

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By L. D. Woodworth, E. E. McGinley

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By E. E. McGinley, L. D. Woodworth

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By R. Silent, N. A. Rousselot

The first producing wells completed in the Kettleman Hills arca were noteworthy for their high gas-oil ratios. As a result they became the object of criticism, and controversies arose based on their alleged lack of gas conservation. Ultimately protracted hearings ensued in the District Court of the area, and diverse rulings and subsequent modifications have been handed down affecting the permissible gas-oil ratios. When the Kettleman North Dome Association was formed in April, 1931, and the control of the major portion of the North Dome area vested therein, it was decided to produce only those wells which had a relatively low gas-oil ratio. Among the wells having the highest gas-oil ratio were the Milham Elliott No. 1 (the discovery well) and the Continental Elliott 12-8. drilled as an offset to it. Under the numbering system adopted by the Kettleman North Dome Association, these wells are now known as 88-2P and 1-12P, respectively. Milham Elliott No. 1 was originally drilled to 7236 ft., then redrilled to 7108 ft. The upper portion of the Temblor Horizon produces with a very large gas-oil ratio; production which actually consists of light crude oil with an accompanying large.volume of gas. Little was known as to the location of the Temblor formation at that time but it is now generally accepted that its top was encountered at 6180 ft., giving 928 ft. of penetration. Initial production was estimated at 4000 bbl. of oil and 80 to 90 million cubic feet of gas per day, giving a gas-oil ratio in excess of 20,000 cu. ft. of gas per bbl. of oil. This ultimately increased to a ratio of about 48,000 at the time the well was killed when it was producing about 1100 bbl. of oil and 52 million cubic feet of gas, with a flow pressure of 1200 pounds. The Continental Elliott 12-8 was drilled to a depth of 6876 ft. with the top of the Temblor at 6100, giving a penetration of 776 ft. The estimated initial production of this well was 7000 bbl. of oil and 130

Jan 1, 1933

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By D. J. McAdam

As shown in three recent papers by the author,6,7,8 in two papers by McAdam and Mebs,9,10 and in a paper by McAdam, Mebs, and Geil,11 the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stresses? as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strengths nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. Ib and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses, with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. Ib shows stress combinations with S2 equal to Sa. The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. Ia shows stress combinations with Ss equal to Sl. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-11 In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1944