Search Documents

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By E. B. Kester

Of the many angles from which coal can be studied it is evident that some have a direct and others have only an indirect bearing on its physical or chemical nature . The more drastic the treatment employed in an investigation , the more inferential become the conclusions permissible from the experimental evidence obtained . Thus , ultimate and proximate analyses tell something concerning age , behavior on carbonization , and possible industrial usefulness , but nothing regarding structure or composition in the larger sense . Strong oxidation reveals the fact that benzenoid , pyrrol , and furane rings are prevalent in the chemical substances present , and milder oxidation indicates that the mass of coal , as in the case of the peats and lignites , is humic in character . But beyond such points of information , very little additional can be gained by the use of these more or less vigorous measures . To gain wider knowledge of the actual constituents of coal substance as found investigators have worked out systems of separation by means of solvents , of which a large number have been employed at various times both singly and in combination . The list of solvents includes petroleum ether , benzene , toluene , xylene , ethyl ether , alcohol , acetone , carbon bisulphide , pyridine , quinoline , aniline , phenol , tetralin , glycol ethyl ether glycol ethylether acetate , glycol methyl ether , glycol diethyl ether , pine oil , mesityl oxide furfural , benzaldehyde , ethylene oxide , rosin , caustic potash in solvents , amyl alcohol plus pyridine , chloroform , carbon tetrachloride , acetylene tetrachloride , naphthalene , and others . Once a coal has been extracted it has become common practice to subdivide the extract by means of partial solution in other and weaker solvents . Thus , we find the oily and solid bitumens of Fischer ( 1 ) , 3 Bone ( 2 ) and others ; the alpha , beta and gamma constituents of Wheeler ( 3 ) ; the classification of Novak and Hubacek ( 4 ) embracing oils , resins A , resins B , bitumens An , bitumens Bn , and bitumens Cn ; Crussard's ( 5 ) malthenes , asphaltenes , and carbenes , borrowed from asphalt terminology; and the 40 or more subdivisions of the phenol extract of coal worked out by Frazer and Hoffman ( 6 ) . Perhaps the primary object of interest in these many researches has been to find the coking principle of coal , and to study it and to learn why certain coals form hard , wellfused cokes , and others merely fall to pieces during carbonization . The origin of the various constituents of the gas and tar , the temperature at which each forms , and something of the mechanism of their synthesis have also been sought , as well as new bases for adjudging rank .

May 1, 1931

Jan 1, 1984

By Matthew Deutsch

A common casualty of modern openpit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow and not minable with realistic equipment. In this paper, these three fundamental openpit mine optimization problems are addressed by encoding them as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are nonlinear and may guarantee the optimality that metaheuristics cannot.

By Fred C. Bond

A study of the settling and thickening of finely divided pulps was undertaken with the object of obtaining certain fundamental relationships, with resulting improvements in the design and operation of mechanical equipment. The subject has been treated in two parts: testing and batch thickening, and continuous thickening, including calculations of capacity and dimensions. Part 1. ? Testing and Batch Thickening The usual method of making thickening tests is to agitate the pulp with a plunger in a graduated glass cylinder and let it settle, while recording the time rate of settling. The settling rates corresponding to different pulp dilutions are found, the ultimate dilution obtained is measured, and the necessary thickener area in square feet per ton of dry solids per 24 hours is calculated, for each pulp dilution. The largest area found is used in selecting the proper thickener size.

Jan 1, 1946

By Heinz W. Sternberg

A method for the electrochemical reduction of the benzene ring was developed and applied to the electrochemical reduction of coal. Successive electrochemical reductions of a vitrain from low-volatile bituminous coal in ethylenediamine saturated with lithium chloride resulted in the addition of 53 hydrogens per 100 carbon atoms. Ultimate analyses and pyridine solubility of the vitrain recovered after each reduction showed that hydrogen added at the beginning has a much greater effect on solubility than hydrogen added at a later stage. Surprisingly, the removal of sulfur from the vitrain takes place only after the more reactive aromatic rings are reduced. Nuclear magnetic resonance analysis and average molecular weight determination of the extracts of the reduced vitrain samples, representing about 18 percent of the vitrain, showed that these fractions had 95 percent of their hydrogen content on saturated carbon atoms and an average molecular weight of 800 to 900. A study of the effect of operating variables on current efficiency showed that current efficiency is highest with aluminum as cathode material and with lithium chloride as electrolyte. A substantial increase in current efficiency of difficulty reducible olefinic double bonds was achieved by adding a proton donor. This result is significant in connection with the electrochemical reduction of coal which proceeds from readily reducible aromatic double bonds to difficultly reducible isolated double bonds. It is proposed that reduction is achieved by electrolytically generated and subsequently solvated electrons and hence does not require prior adsorption of the substrate at the electrode surface. This offers a distinct advantage for electrolytic reduction of sparingly or insoluble substrates such as coal.

Jan 1, 1967

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011

By A Turner, P Hills, D Johnson

Underground mining for gold began in Beaconsfield in 1877 and development of the Tasmania Mine saw the sinking of multiple shafts, including the Hart Shaft over the ensuing 35 years. The mine closed in 1914 at a depth of 455 m due to prevailing economics, eventually reopening in 1999. The modern mine closed in 2012 after extending the mine from a historical depth of 455 m to the exhaustion of the modern Ore Reserve at a depth of 1210 m. West Tamar Council took over the lease for the immediate area around the Hart Shaft as an extension of the adjacent museum. The Hart Shaft and above ground structures became a significant drawcard for visitors. Tasmania was affected by sustained wet weather during May, June and July of 2016 which caused severe flooding and significant Statewide damage. This uncharacteristically intense wet weather caused saturation of the ground surrounding the Hart Shaft. Eventual shaft failure was first identified in August 2016. The failure of the shaft occurred at approximately 50 m below surface and resulted in a plug of material completely blocking the shaft. Significant surface subsidence affecting the surface infrastructure ensued. Due to the unstable nature of the surrounding material, it was determined that addressing the failure above the blockage would not provide a permanent solution to prevent the continued flow of material into the shaft. Many options to stabilise the shaft were considered, however it was assessed that a concrete plug in the shaft in competent ground at a depth of 100 m below surface and well below the blockage, would provide the only long-term solution. Man-entry was considered unsafe. The solution to access ultimately entailed filling the entire shaft with granular fill up to 100 m depth to act as formwork for a concrete plug. The rising mains at 400 mm and 250 mm diameter, which remained in place in the shaft, provided the avenue for placing the fill and ultimately, the concrete plug. Once the plug was in place the remainder of the shaft up to the underside of the blockage and over the top of the blockage to the surface was successfully filled with a combination of more granular fill and flowable cement stabilised sand. The Hart Shaft and surrounding above ground infrastructure was successfully stabilised and re-opened to tourist access. CITATION:Johnson, D, Turner, A and Hills, P, 2018. Stabilising and filling the Beaconsfield Hart Shaft, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 42–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G. Scott Zimmer

Mine planning at Cassiar consists of an annual cycle of projection, control, evaluation and revision following completion of annual diamond drilling during the summer months . The inherent difficulty in evaluating fibre grade and distribution, combined with a high-wall phase or push-back mining system, requires continuous modification to designs and schedules based on a cumulative evaluation of equipment performance and prediction versus production. To expedite the planning sequence, a mini-computer system has been introduced which allows emphasis to be placed on optimizing designs, exempting personnel from manual calculations and tabulations.

Jan 1, 1978

By Mohamed A. Sakr

An experimental study on the behavior of pile group's arrangement under lateral load was carried out in the level ground and at crest of sand slope 3H: 2V. Tests were conducted on single pile and pile groups with center-to-center pile spacing of 3D. The model piles were founded in sand with relative density 25%. Several configurations of pile groups were used to study the effect of piles arrangement in the group (series or parallel) with respect to slope crest. The behavior of the pile groups in the level ground was compared with the behavior of pile groups at different configurations at the slope crest. Based on the test results, the behavior of laterally loaded pile groups adjacent to a slope crest depends largely on piles arrangement in the group with respect to direction of the lateral load. Pile groups in the level ground have more resistance to lateral loads when they are arranged in a parallel configuration than in a series, whereas the reverse is true in cases of pile groups constructed near to the edge of a slope. It is advisable to use the pile group in series arrangement for groups constructed at slope crest to minimize the effect of the ground slope on lateral capacity of piles and the occurred deflection and maximum bending moment of the lead row in the group.

Jan 1, 2010

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives have several potential pitfalls. These are outlined in the present paper. The main findings are as follows:•,Coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate •,For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where, ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition •,Significant errors could be made if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen) •,For elemental analyses, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range •,For representation of sulphur in coal, double-counting due to SO3 in the ash analysis should be avoided •,Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2; however, use of some of these species without considering the experimentally determined gross CV results in significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy (up to 6.9% error for a set of South African coals). Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than the abovementioned four, provided the enthalpy is corrected •,It is recommended that an ‘enthalpy correction value’ is incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to the form of carbon being different than graphite should be used, as that would imply doublecounting some effects."

Jan 1, 2014

By H. Sevim

In a recently developed long term open pit production planning model, the optimum plan is found by exhaustively searching through nested pits of maximum-metal contents. A more efficient, dynamic programming (DP) based search algorithm now replaces the exhaustive search algorithm which was requiring prohibitively long execution time in real life cases. The logic and the formulation of the newly developed search algorithm are illustrated through a small hypothetical case. A real life gold deposit is treated to demonstrate that the algorithm does indeed find the optimum production plan among all possible plans. A comparison, in terms of computational savings between the two algorithms is also given.

Jan 1, 1994

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017

By Kevin Fitzpatrick, Carmen Scalise, Patrick Jensen

"The Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) owns and operates the Tunnel and Reservoir Plan (TARP) system which was adopted in 1972. TARP is a network of 110 miles of deep tunnels and ultimately 3 large reservoirs to combat waterway pollution and flooding within a 350 square mile area served by combined sewers. The original TARP concept included additional tunnels to convey CSOs from the largest storms to the reservoirs. With the initial TARP tunnels complete and the reservoirs nearing completion, MWRDGC commissioned hydraulic and hydrologic modeling studies to analyze the benefits of additional conveyance tunnels. These updated studies optimized the configuration of additional tunnels considering integration with potential future local sewer system upgrades. The alternatives considered several routes of 25, 30, and 35 foot diameter tunnels, ranging from 10 to 18 miles. Alternatives were analyzed based on projected reductions to basement flooding compared to the relative costs. TUNNEL AND RESERVOIR PLAN After World War II the Chicagoland area underwent rapid growth and development. With the Metropolitan Water Reclamation District of Greater Chicago's (MWRDGC) service area becoming increasingly impervious, the flat Chicago landscape was increasingly at risk of significant flooding. In the mid and late 1950's, Chicago experienced multiple extreme storm events that had significant impacts on the city and generated the momentum necessary to initiate what would ultimately become one of the world's largest civil works undertakings. In 1957 a Flood Control Coordinating Committee was formed, consisting of representatives of the MWRDGC, Illinois Department of Public Works, Cook County, and the city of Chicago, to review various plans and develop recommendations for a course of action. With more than 50 alternative concepts being identified, the Tunnel and Reservoir Plan (TARP), which itself is a composite of various alternatives, was adopted the by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) in 1972. The need to adopt a long term plan was further influenced by the Clean Water Act, which was enacted only 8 days prior."

Jan 1, 2016

By Janice K. Means

The purpose of this paper is to provide the seminar attendee with: information on pipeline construction, operation and standards to better equip him (or her) to analyze the ultimate effect of blasting stress on pipelines; an introduction to the analysis of blasting effects to pipelines using the American Gas Association analysis method; and; supplemental sources useful in the analysis of blasting effects to steel pipelines, and, in particular, on natural gas pipelines.

Jan 1, 1992

By Zhaohui Wang, Jiachen Wang

"Effective surrounding rock control is a prerequisite for realizing safe mining in underground longwall faces. In the past three decades, longwall top-coal caving mining (LTCC) and single pass large height longwall mining (SPLL) found expanded usage in extracting thick coal seams in China. The two mining methods lead to large void space left behind the working face, which increase the difficulty of ground control. Longwall face failure is a common problem in underground mining, which is induced due to low strength and high fracture density of the coal seam. Moreover, the stiffness of main components included in the surrounding rock system also greatly influences longwall face instability. Correspondingly, the surrounding rock system is developed for LTCC and SPLL faces in this paper. Mechanical conditions for simultaneous balance of roof structure and longwall face are put forward by taking the stiffness of coal seam, roof strata, and hydraulic support into account. The safety factor of the longwall face is defined as the ratio between its ultimate bearing capacity and the load imposed on it. The influence of coal strength, stiffness of the coal seam, roof strata, and hydraulic support, as well as the movement of roof structure, are analyzed. Finally, the key elements dominating longwall face stability are identified for improving surrounding rock control effectiveness in LTCC and SPLL faces.INTRODUCTIONThe concentration of coal mining in China is gradually shifting to the west region, and there are a large number of thick coal seams in the newly formed coal mining area. Therefore, the surrounding rock control problems related to mining of thick coal seams will become the focus of research in the field of mining engineering in the future. There are two kinds of mining methods for thick coal seams in China, including single pass large height longwall mining (SPLL) and longwall top-coal caving mining (LTCC). Both methods can accomplish the goal of excavating the full thickness of thick coal seams at one time. SPLL mining benefits from the improvement of the development level of associated equipment. The appearance of large hydraulic supports and high power shearers ensure that the height protected by the hydraulic supports and the height of the sheared coal are the same as the coal thickness. LTCC mining benefits from mining technology advantages. The thick coal seam is divided into two sub-layers, and the working face is normally installed in the bottom layer, while the top coal is caved under the compressive forces due to mining. Therefore, there is a scraper conveyor at the front of the hydraulic support for transporting the sheared coal and another one at the tail for transporting caved top coal. Both SPLL and LTCC methods realize one-off recovery of thick coal seams."

Jan 1, 2018

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and thereby reduces processing costs, recovery losses, and refuse generation levels. In this paper, new approaches for optimal control of the segregation process, using time series models and empirical distributions, are presented and demonstrated using field data.

Jan 1, 1998

By J. Gordon Parr, D. A. Whitaker, G. A. Yorko

High purity alloys of zinc with 25 per cent to 50 per cent aluminum, have been prepared. Mechanical properties of the as-cast and heat-treated alloys have been related to constitution, determined by x-ray diffraction and microscopic methods. Investigations include the effects of aging and of small nickel additions on the properties of the alloys.

Jan 1, 1960