Search Documents

By J. Visman

A simplified method of assessing the characteristics of a cleaning unit, including washability curves, yield figures, ash error, separating gravities, and error curve. FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, information that ultimately can be secured only from actual tests made in the laboratory or in the washery. It is not the purpose of the present discussion to compare the merits of various characteristics, but to describe the general method of calculation, including a method of obtaining data with a minimum of laboratory work. All data presented here were derived from tests made at the plant with portable field equipment, using small quantities of varsol, carbon tetrachloride, and bromoform. It will be explained later that the use of standard fractional ash contents designated normalized ash contents aids considerably in reducing the routine testing of coal cleaners. Like any other statistical procedure, this method has limitations, and it is not recommended for any work in connection with guarantees. Even a varying commodity such as coal, however, will follow the law of large numbers, which is the basic law of statistics, thus allowing simplification of test work without appreciable loss of accuracy. The characteristics needed for evaluating cleaner performance are normally derived from a float-sink analysis of samples of the clean coal and the refuse, followed by ash determinations of the various fractions. Usually a sample of feed is also collected to find its ash content and to make a single specific gravity cut, both in connection with determination

Jan 1, 1955

By J. E. Gould, H. J. Hand

MANY independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final deoxidation In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding over-deoxidation to minimize the amount of inclusions present and to make as sound a steel as possible For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or long FeO values The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishing the state of oxidation at a given time Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors Data obtained are from actual furnace operations, the metal test being of the spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States Steel Corporation This method of taking open-hearth metal temperature was invented by Collins and Oseland,1 and was developed into its present form by L 0 Sordahl,2 of the Research Laboratory The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications 3,4,5 Slag components were obtained by chemical analysis Data were taken from four 165-net-ton furnaces during the working period of the heat Recognizing that additions of ore affect the

Jan 1, 1942

By R. R. Brandenthaler

CONTROLLING -the pressure under which a well produces crude oil has advantages that are ap¬parently not entirely realized by many operators in the Mid-Continent district. The possibilities of utilizing well pressures are indicated by a series of ex-periments recently completed by the Bureau of Mines in which pressure control was successfully applied to 20 wells in, the Davenport field. The flowing period of all of .the wells was lengthened in some instances it was. more than doubled. The daily oil production from approximately one-half of the tested wells was in-creased. The amount of gas produced per barrel of oil was decreased, and this, in addition to a slower rate of decline in production, indicated that the ultimate re-covery had been increased. The successful application of pressure control to flow-ing oil wells must take into consideration the relation-ships existing between pressures in the different parts of the system which, though not equal, are nevertheless more or less interrelated. These relationships, which have such an important bearing on the results obtained by applying pressure control, are as follows: A change in rock pressure will affect the tubing pressure, casing pressure, and differential pressure, but it will not affect the trap pressure. A change in tubing pressure will affect the differential pressure and casing pressure; also, a change in casing pressure will affect the tubing pressure and differential pressure. Trap pressures are not affected by rock pressure, casing pressure, tubing pressure, or differential pressure, unless the traps are required to handle gas and oil beyond their capacity. Trap pressures will affect the differential pressure, tubing pressure, and casing pressure and any changes at the well-head, whether differential pressure, tubing pres-sure or casing pressure, will affect the pressures in the well. Any change in rock pressure results in a change in the tubing pressure, casing pressure, and differential pressure. When any sudden or unusual change in well-head pres-sures occurs (for example, an erratic tubing pressure), and when a sudden decrease in oil or gas takes place, it is al-ways advisable to note whether the trap pressure has changed. If the trap pressure has not changed, note whether the oil line from the trap to the flow-tank has become clogged, as would be evidenced by a rise in the oil level in, the trap. If the oil line is functioning properly, and if the trap pressure has not changed, the flow-line from the well to the trap should be inspected. If it is free from obstructions, then changes in the differential pressure, tubing pressure, and casing pressure must be due to changed well conditions.

Jan 4, 1927

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By B. H. Caudle, A. B. Dyes, R. A. Erickson

The study of the influence of fluid mobilities on the sweepout pattern resulting from the injection of gas or water has been extended to cover the production period which follows breakthrough of the injected material. Mobility ratios over the range common in field operations (0.1 to 17) were studied for several pattern floods (five-spot, staggered, and direct line drive). The experimental data required for these studies were obtained by the use of the x-ray shadowgraph technique using miscible oil phases of different viscosities in porous plate mode1s of a reservoir element. From the shadowgraph pictures obtained before and after breakthrough of the injected fluid, flowing ratios at the producing well and cumulative volumes injected were calculated. The method for applying such data in predicting field behavior is illustrated for a water flood of a five-spot. For this case a range of mobility ratios of 0.5 to 5.0 results in: (I) nearly complete (95 to 100 per cent) sweepout pattern efficiencies at abandonment conditions, (2) production after breakthrough being responsible for as much as one-third of the total recovery at the lower mobility ratios, and (3) a twofold variation in the operating life of the reservoir. In determining the merits of a secondary recovery operation, the fraction of the reservoir which is ultimately to be swept by the injected fluid is of major importance. Because of its significance a large amount of research has been applied to the study of areal sweepout efficiency. Muskat, Wyckoff and Botset1,2 have presented the classic analysis of the pattern efficiency at breakthrough for several injection patterns in which the mobility of the fluids ahead of the injected phase front was equal to the mobility of the fluids behind the front. Aronofsky3 as extended this analysis of recovery at breakthrough through numerical computations and by the stepwise use of the potentiometric model to include the effect of different fluid mobilities ahead of and behind the invasion front on the line drive performance. Fay and Prats' have also employed numerical computations to show the influence of one other condition of fluid mobilities on the five spot flood. In a previous paper' a new method of attack on this problem which employed x-ray and porous plates was described. At that time experimental results were also presented which described the effect of fluid mobilities on the reservoir area contacted by the injected fluid at breakthrough for the five spot and direct line drive patterns. Most of the literature pertaining to sweepout pattern efficiency has emphasized the pattern which is obtained at breakthrough of the injected phase. The increase in the sweepout pattern which occurs after breakthrough

Jan 1, 1955

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unex-pected, but that along with the factual discovery there is a constant effort to understand. It appears that one's interest in, and satisfaction with, the discovery of an array of new experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner. Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows. Of course, there have been long arid stretches in the history of physics in which new data of unquestioned ultimate importance have piled up, without much inspiration or illumina-tion in the way of understanding. For 50 years spectroscopy had such an arid history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered. The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the same sort of situation as spectroscopy before the advent of Bohr. A great many kinds of data were collected for a great many solid and liquid sub-stances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected. But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthu-siasm of the collector that kept me going. However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand It appears that. one's interest in, and satisfaction with, the discovery of an array of news experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows Of course, there have been long and stretches in the history of physics in which new data of unquestioned ultimate importance ham e piled up, without much inspiration or illumination in the way of understanding For 50 years spectroscopy had such an and history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the Same sort of situation as spectroscopy before the advent of Bohr A great many kids, of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By W. A. Tiller

SEVERAL authors1-6 have shown that, during solidification from the melt, the direction of formation of substructure boundaries depends upon the direction of heat flow and the rate of solidification of the metal. The most prominent of these observations was that a preferred orientation developed during the solidification of the columnar zone of an ingot which for face-centered-cubic metals was the <100> direction. Previous explanations1-&apos; given to account for this preferred orientation and the other boundary phenomena are all based on the premise that the phenomena are characteristics of the pure element. However, recent experiments by Rosenberg and Tiller7 have demonstrated that the preferred orientation in pure lead is the <111> orientation, and that the heretofore observed <100> orientation is due to the effect of solute on the mode of solidification of the metal. Teghtsoonian and Chalmers,4 studying striation boundaries in tin, and Chalmers and Rutter,5 studying corrugation boundaries in tin, showed that these substructure boundaries were aligned parallel to the axis of heat flow for slow rates of growth, and that the alignment varied from this direction as a function of the rate of growth. to approach the den-drite direction at high rates. Chalmers,6 studying the direction of formation of a grain boundary separating two crystals of different orientation, showed that at slow growth rates the boundary is parallel to the axis of heat flow, while at higher speeds it will deviate from this direction, sloping into the crystal whose dendrite orientation departs the most from the axis of heat flow. It is this phenomenon that allows certain crystallites in the chill zone region of an ingot to encroach on their neighbors and ultimately produce the preferred orientation of the columnar zone of the ingot. Since the previous explanations of this preferred orientation are unable to account for the recent observations,&apos; a new mechanism will be considered. This will lead to an explanation of the other substructure boundary phenomena as well. Investigations by Graf,8 Billig,9 Rsenberg,10 and others have demonstrated in a striking fashion that crystal growth takes place by the deposition of individual layers oriented along the close-packed planes of the material considered. This lamellar or

Jan 1, 1958

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

By Harrison Everett Ashley

Slimes are usually defined as all material passing a certain sized sieve, which is invariably the finest sieve employed by each metallurgist in his tests; 100-mesh and 200-mesh have been taken as the limits by different writers in recent volumes of the Transactions; 150-mesh is common practice. The reader of the first two volumes of Richards&apos; is impressed by the inflexibility with which all grinding-arrangements are praised or condemned according as they make little or much slime. Until recently, one of the principal aims of the mill-man was to keep down the slimes. He was obliged to have separate apparatus for sand- and slime-treatment. The latter was sometimes puzzling and erratic. Often it was found most economical to omit treatment of the slimes entirely, or to store them in immense basins or heaps, waiting for possible future improvements in methods of treatment. Recently, improved processes of agitation and filtration have made possible the successful extraction of values from many slimes. The tendency, when the metal is exceedingly finely disseminated, is to cut out all sand-treatment and to slime everything. These processes have been almost entirely mechanical in their conception, and it is the object of the present paper to show that certain chemical considerations may greatly hinder or assist their successful operation. It has long been a source of dissatisfaction to chemists that their analyses fail to be of much help to the clay-worker; that it is a matter of common occurrence for clays of closely identical ultimate chemjcal constitution to show the widest possible divergence in physical properties.

Jan 1, 1911

By Henry H. Logan

THE purpose of mine-hoist safety controllers is to prevent hoists from being operated at speeds above those considered safe and expedient, to ensure proper acceleration and retardation near the ends of travel, and to prevent overwinding. In other words, they are to safeguard the normal speeds and movements of the hoisting drums and cages. The object of this paper is to explain the fundamental principles of hoist controllers, and to aid in their selection, installation, and maintenance. There have been many designs of mechanical hoist controllers, the basic elements of which as ultimately developed consisted of a flyball governor and another movable member supported by a frame and arranged to move in a vertical, horizontal, or rotary direction, depending upon the particular design, the whole mechanism arranged to be driven in synchronism with the hoist drum. In case of overspeeding, inadequate retardation, or overwinding, a pawl or catch controlled by the governor would engage teeth or dogs on the moving member, which through mechanical connections would cut off the power and set the brakes. Since in strictly mechanical hoist controllers valuable time was lost while the various mechanical movements took place, an important development was the invention of controllers partly mechanical and partly electrical. This type of controller has a governor and movable cams to be driven in synchronism with the hoist drum, the governor representing the hoist speeds and the cams profiled to form a pattern for retardation, representing the travel of the cages in the shaft. This type is also provided with an overspeed switch and usually with a pair of selective-limit switches, one for the top limit and the other for the bottom. In overspeeding or failure to retard in accordance with the profile of the cam, the overspeed switch will be opened, or if the top or bottom limit is overrun one of the limit switches will be opened, breaking the retaining circuit of a contactor or magnetic latch, causing the power to be cut off and the brakes applied. When the speed falls to the predetermined safe speed, the overspeed switch closes, and a hoist equipped with power-operated brakes controlled in emergency by a solenoid-operated valve can be restarted immediately by simply moving the master control lever to the "off" position and then applying power-unless brake interlocks are used, in which case the brake lever or levers must also be brought to the "applied" position, after which the hoist can be restarted in the usual way. When hand-reset weights instead of solenoid-operated mechanism are arranged to set the brakes for emergency, it is necessary to reset the weights manually, besides bringing the master control lever to the "off" position before the hoist can be restarted. Should a final limit be slightly overrun, and a stop made with a limit switch held open by a cam, it is necessary for the hoistman to use a "backing-out" switch which short-circuits the overrun limit switch, reestablishing the hoist-control circuit, and simultaneously opening the

Jan 1, 1940

By Van H. Manning

Of all the war work by the Bureau of Mines none ultimately covered such a variety of processes and equipment, employed as many men, or called for as large an outlay as that started in con- nection with the solution of problems relating to the use of noxious gases in warfare. Beginning with an investigation to develop the best type of gas mask, the scope of the work extended until it included researches relating to a wide range of devices, such as different types of poisonous and irritating gases and smokes, smoke screens, gas shells and gas bombs, flame throwers, trench projectors for firing gas bombs, signal lights, and incendiary bombs. The Bureau of Mines in starting this work selected the necessary personnel, pro- cured the early equipment, and for some months, from the begin- ning to June 30, 1917, paid the cost of the work from its own funds. The Bureau of Mines built up a research staff of more than 700 chemists, including many of the most prominent chemists in the country, and obtained the cooperation of many of the universities and chemical companies. When the results obtained through this research were to be applied by the War Department, the Director of the Bureau of Mines cooperated in the selection of men to have charge of manufacture or further development, recommending chemiste who subsequently received commissions in the Army. The personal cooperation with the War Department was thus very close. The bureau can fairly claim that because it started this work on gas warfare and received the hearty support of the Department of War, the Navy Department, the National Research Council, and State, educational, and private institutions, the country was in July, 1918, months ahead of where it would otherwise have been in the production of gas masks and other devices. The production of toxic gases then far exceeded the supply of shells. In addition the later work in gas-mask manufacture by the Surgeon General's Office of the Army, which resulted in the development of the best mask produced anywhere; in gas manufacture and gas proving-ground tests by the Bureau of Ordnance, and in the chemical warfare pro- gram of the Navy, including the use of smoke screens, shells and toxic gases, were the direct results of the bureau's experimental work. The American charcoal and soda lime, developed through the research work, are the best used by any nation. The Bureau of Mines was instrumental in developing satisfactory methods of manu- facturing chlorpicrin, phosgene, mustard gas, brombenzylcyanide, cyanogen chloride, and other noxious substances on a large scale. The bureau also developed a smoke funnel for the Navy which no doubt saved many ships from submarine attacks, and devised smoke barrages, signal lights, incendiary darts, etc., for the Army. The Ordnance Department of the Army asked for incendiary bombs and were furnished with bombs better than any made previously. Perhaps the greatest single result of the research work has been the demonstration of the value of the services that the chemist and chemical engineer can render in time of need and the recogni- tion of chemical investigations as a necessary function of the Gov- ernment.

Jan 1, 1919

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By W. D. Robertson

THE effect of a tensile stress in accelerating the corrosion-cracking of certain alloys of aluminum, magnesium and iron is widely recognized. The literature is extensive and it is only necessary to cite the recent ASTM-AIME Symposium.1 There are, however, no experimental data conclusively showing the effect of an applied compressive stress. It has been inferred, from the generally accepted mechanism postulated for the acceleration of corrosion by an applied tensile stress, that a compressive stress would inhibit corrosion. Furthermore, it is observed that corrosion cracks invariably start on the tension side of a specimen bent as a simple beam. This observation has led to the suggestion that shot-peening of the surface would inhibit or eliminate stress-corrosion cracking in magnesium alloys, and aluminum alloys.3 However, the degree of inhibition produced by shot-peening does not appear in the literature except for the above qualitative references which are unsupported by experimental data. Moreover, while peening undoubtedly imposes a surface compressive stress, the alteration of the surface by the severe cold-working involved complicates the interpretation of the results with respect to the effect of a compressive stress alone. If corrosion proceeds along preferential paths produced by precipitation from solid solution, it is easily understood how a component of tensile stress normal to these paths will accelerate the corrosion and lead to ultimate failure. On the other hand, if the metallurgical conditions are such as to create preferential corrosion paths, then it is difficult to understand how a compressive stress, produced by shot-peening or any other method, can inhibit corrosion except in the sense that the accelerating factor is removed. Thus, if the basic corrosion mechanism remains unaltered, there should be little or no inhibition resulting from the application of a compressive stress if in¬hibition is defined as the reduction of the degree of corrosion below that experienced in the unstressed state. The experiment described below was performed to isolate and evaluate the effect of a compressive stress on the corrosion and stress-corrosion cracking of a high strength aluminum alloy (24-S); and, by a comparison of the corrosion rate of specimens subjected to an applied tensile stress, compressive stress and in the unstressed state, to clarify the role of stress in intergranular corrosion. EXPERIMENTAL PROCEDURE The experiment was conducted with the aluminum-copper-magnesium alloy known as Duralumin 24-S.* Specimens, 0.064 in. thick, in the form of I in. wide strips sheared parallel to the rolling direction,

Jan 1, 1947

By David A. Hedderly-Smith

Sealaska Corporation, the Alaska Native Regional Corporation of Southeastern Alaska, was organized under the laws of the state of Alaska pursuant to the federal Alaska Native Claims Settlement Act of 1971. Large areas of Sealaska&apos;s 630,000-acre (250,000 hectare [ha]) fee subsurface holdings are underlain by carbonate, and while much of this material is assumed to be common variety limestone and lesser dolomite, at least two areas in the Silurian Heceta Limestone contain high-quality limestone at tidewater. This limestone has many potential commercial uses. On northern Prince of Wales Island, about 90 miles (144 km) north-northwest of Ketchikan, resource development at Sealaska&apos;s Calder deposit has established a reserve of 13 mil- lion short tons (st) (12 million metric tonnes [mt]) of carbon- ate rock containing an average of greater than 98 percent CaC03, approximately 0.5 percent MgO, less than 0.5 per- cent Si02, and approximately 0.15 percent Fe203, with insolubles averaging less than 0.5 percent and an average Hunter Brightness of 92.07 for the -150 mesh grind (with a bright- ness cutoff of 90). The deposit is open at depth and to the south. Ultimate reserves will likely be several times those currently established. In 1998, Sealaska began mining the Calder deposit, with about 100,000 st (90,000 mt) produced, and also completed a marine terminal one half-mile (800 m) from the deposit. The terminal can load ships up to 680 feet (200 m) in length at a rate of 2,000 st (1,800 mt) per hour. 0 m) in length at a rate of 2,000 st (1,800 mt) per hour. On Dall Island at Breezy Bay, about 60 miles (100 km) southwest of Ketchikan, Sealaska has identified a limestone reserve in excess of 150 million st (135 million mt) that (based on 18 surface samples distributed evenly over about a section of land) contains about 98 percent CaC03, and less than 0.5 percent MgO, 0.5 percent Si02, and 0.15 percent Fe203. Brightness of the Breezy Bay carbonate is considerably less than at Calder. Five samples of brighter material from Breezy Bay returned brightness analyses in the high 80s and low 90s; average brightness is probably below the mid- 80s. Sealaska has also identified a deposit containing more than 19 million st (17 million mt) of similar rock near View Cove, a few miles south of Breezy Bay.

Jan 1, 2001

By J. Greenspan

The anisotropy of fracture and slip, that is, the brittleness and ductility of the beryllium single crystal, is characteristic also of po1ycrystalline beryllium in which the grains are oriented in a preferred manner. Beryllium with grain orientations resulting from hot working either unidirectionally or bidirectionally is ductile or brittle in directions given by the anisotropy and orientation of the grains. Textures developed from various hot-working sequences are given, and tensile results are correlated with textures. Not only texture, but fine grain size is necessary for obtaining high tensile elongation. Ultimate tensile strength and elongation are both correlated with grain diameter. Of particular interest is the case in which unusually high tensile elongations of 30 to 40 pct are obtained when basal planes are oriented to carry THE beryllium crystal (of nominal purity) is probably unique among metals with respect to its unusually acute anisotropy of slip and fracture. While extensive slip can occur on the system (1010) [ll20] starting at about 19,000 psi, the (0001) plane is particularly vulnerable to fracture at 4500 psi or less. Fracture occurs also on the (11zo) plane at about 26,000 psi.1"3 Further, there seems to be no other slip System which contributes significantly to

Jan 1, 1960