Search Documents

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

John Duer Irving, who left his post as Professor of Economic Geology at the Sheffield Scientific School, New Haven, Conn., to join the Eleventh Regiment of Engineers shortly after the declaration of war, died in France, July 26, 1918, from an attack of pneumonia. Through the initiative of Mr. Benjamin B. Lawrence, a memorial service to Captain Irving was held at St. Paul's Chapel, Columbia University, on Sunday afternoon, August 4, which was' attended by members of Captain Irving's family, and about four hundred of his friends from Columbia, Yale, the American Institute of Mining Engineers and the Association of the 11th Regiment of Engineers. Professor James F. Kemp delivered the memorial address, and has prepared for the Institute the following account of Captain Irving's life, Professor Kemp and Captain Irving having been associated on the most intimate terms for a number of years. , The war has brought home to friends and kin in the western shores of thc Atlantic many losses whose suddenness has the shock of a blow. Many more will follow, but none can leave a sharper sense of regret than the news that the keen and productive mind; the inspiring teacher; the successful and considerate editor, the fine, true man and friend had all passed away when John Duer Irving made the final great gift to the service of his country, in the cause of decency and right. In the closing days of July, the cable brought the tidings that toward midnight on the twentieth of the month pneumonia had proved too great a tax upon one already worn by excessive labors. John Duer Irving was born in Madison, Wis., August 18, 1874. His father, Roland Duer Irving, was at the time professor of geology, mineralogy and metallurgy in the State University of Wisconsin.' Roland . Irving, the father, had entered Columbia College in 1863, but trouble with his eyes compelled him to suspend his studies in the classical course in his sophomore year, and to replace study with some months of life and travel in England. Ultimately his eyes became stronger, and he entered the School of Mincs, completing the course for the degree of Engineer of Mines in 1869, with the third class graduated. The class of eleven contained other future geologists. It numbered on its roll Henry Newton and Walter P. Jenney of the early survey of the Black Hills, where John, future son of Roland, was in the course of years to make his doctor's dissertation, and with its publication his really serious entrance into the profession. Roland Irving was a favorite student of Professor J. S. Newberry, affectionately known to all of his students as "Uncle John," and after some experience in mining and smelting in Pennsylvania and New Jersey, joined the Ohio Survey under Dr. Newberry. The work in Ohio was largely performed during the vacations of the University of Wisconsin, to whose chair Roland Irving was called in 1870. Later, his residence in Wisconsin led to two events of prime importance in the history of American geology. He began the study of the Gogebic iron range and caught the clue to the origin and stratigraphy of the iron ores of all the Lake Superior ranges; and he later undertook the mapping and description of the copper-bearing rocks of the Lake Superior basin. The formative years of the son, John, were passed in a home where the father.

Jan 1, 1920

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By Arthur Taggart

Recent jig practice has shown such marked departures from the pronouncements of the textbooks, particularly as to particle size recovered and size range of feed, as to make it desirable to reexamine the mechanism of jig action. This paper presents the results of such a study. The general conclusions of the Paper are: I. A jig bed is a bi-functioned as well as bi-parted body. The upper layer comprises a plastic stream moving slowly in a substantially horizontal direction from feed lip to tail board. It serves to rough out tailing and light middling and to pick up heavy middling and lift it out 01 the jig box. The lower layer acts as the ultimate separating means by absorbing concentrate and rejecting heavy middling. 2. The separating function of the lower layer is performed in three definitely diflerent ways, depending upon the relative sizes of the grains presented to it and those composing it. Experimental The experimental work consisted of close and long-continued visual observations of operating beds in a plunger jig, eccentric driven, and in determinations of the settling rates of various metal spheres through a quartz bed under various conditions of operation. Falling velocities were measured by an ingenious method devised by A. 6. Dorenfeld, a student in the Mining Department at Colum- bia. Spheres of different metallic alloys, 3/8-in. diameter, were cast with a short piece of fine copper wire frozen in to Serve for suspension-A short piece of black cotton thread was looped to the top of the wire to serve as an indicator. The set-up for a test is shown in Fig. I. The thread should be boiled, if necessary, to make it freely water absorbent. The piece of clean plate glass D is supported rigidly at the proper height in a vertical position. The white scale E is similarly supported behind the glass. At the beginning of a test, D is filmed with water by holding it (best with clean rubber finger cots) under running tap water. It is then clamped in approximate position and C, already wet, is laid across it and drawn straight and vertical with the upper end at or near the top of D, and the ball A slightly above the top of the expanded bed. The water film holds the string to the glass. For a test the string is released, its upper end position noted just after the top of the ball becomes submerged, when the corresponding time is read, and thereafter simultaneous readings of position and time are taken as desired. Results of the visual studies of the bed are given at the pertinent places in the following discussion. Results of the settling tests are summarized in Figs- 2 and 3. Definitions The name bed as used herein refers to the entire mixture of solids and water filling the jig box. A layer is a stratum of a bed composed of particles of substantially the same specific gravities. A granular product is long-range when it approximates a crushed or ground product limited as to upper size only; a short-rafzge product is one closely sized. A bed is loaded when operating with continuous feed and discharge of products; it is unloaded when pulsating norma11y but neither being fed nor

Jan 1, 1943

By R. L. Slobod, B. H. Caudle

In the past, the main emphasis in attacking the problem of the recovery of oil has been on the determination of fluid flow characteristics and residual oil saturation in the part of the reservoir which is contacted by a displacing phase. It is recognized that the determination of the fraction of the reservoir contacted in secondary recovery operations is also of great importance in predicting the ultimate recovery to be expected. A method is described in which radiographic techniques are used to determine these areal sweepout factors for any type of well spacing. Data showing the relationship of viscosity ratio and relative permeability to areal sweepout efficiency are presented for the five spot and the direct line drive well spacing patterns. Further applications of the method to studies of the displacement efficiency in the area contacted are mentioned. INTRODUCTION The problem of increasing oil recovery from typical reservoirs is generally attacked by trying to devise some means for reducing the residual oil in that part of the reservoir which is contacted. The fraction of the reservoir contacted in the displacement process. however, is also of major importance but has been given less consideration in the past. one reason for this neglect is the meager information available on the portion of the reservoir contacted and the magnitude of changes in this factor as operating conditions are varied. Until recently, the only means available for determining this quantity has involved the use of the electrolytic or poten-tiometric modelsl in which one is limited to working with a mobility ratio of unity. while means for calculating the volume of a reservoir contacted do exist. the calculations are very tedious for systems with mobility ratio different from unity. Recently several such determinations have been reported,213 and an experimental method involving a step-wise use of potentiometric models has been described.' A new method which has been developed for studying the areal distribution of phases in a porous medium is discussed below. This tool can be' used to determine the effect of operating variables such as viscosity, relative permeability, presence of gas, mobility ratio, rate and stratification on the fraction of the reservoir contacted by the displacing medium. This development based on the use of X-rays gives a pictorial representation of the location of the phases. Further, the amount of each phase at each point of interest can be determined quantitatively. X-RAY METHOD FOR AREAL STUDIES In this method the location of various phases distributed Over a test area are observed simultaneously by obtaining a photographic record of the transmission of X-rays through the test plate. This procedure is an adaptation of the radiographic techniques which have 10% been used in the medical and industrial fields. Just as the medical profession uses a chest plate to show spatial interrelationships, the location of an X-ray absorbing fluid and a nonabsorbing fluid in a porous medium can be determined by obtaining a photographic record of transmitted X-rays. Moreover, as changes occur in such a System, these changes can be observed by taking successive photographs. Previously, X-ray methods have been used in fluid flow studies to determine quantitatively the saturation at a given point in the system. The intensity of the transmitted X-rays was measured by an ionization chamber, so that a point by point survey of saturation could be made. In comparison with this earlier quantitative procedure, the photographic procedure which simultaneously observes the saturation at many

Jan 1, 1952

By R. L. Perrine

This paper presents results obtained by consider ation of unstable miscible displacement within a porous medium as a quasi-turbulent displacement process, that is, a process characterized by fluctuations around a simpler, mean flow behavior. The instability usually results from the miscible displacing fluid having a viscosity lower than that of the displaced fluid. Such instability is evidenced in suitable experiments by the presence of viscous fingering. A unified theoretical relationship applicable to both stable and unstable displacement is derived. Parameters in the theory are obtained by empirical means. Although the theory describes an idealized conceptual model, agreement with experiment is quite reasonable up to moderately adverse viscosity ratios, such as 17:1. INTRODUCTION Many experimental studies of miscible displacement in porous media have been conducted with prediction of reservoir displacement efficiency as the ultimate objective. Most such studies have utilized lower displacing than displaced fluid viscosity, scaled to potential reservoir fluid pairs. Theoretical approaches have been largely limited to unit viscosity ratios, however, in spite of the necessity for an understanding of the mechanism of the unstable, adverse viscosity ratio displacement process. An obvious reason is the difficulty of describing in mathematical form the viscous fingering characteristic of these conditions. Observation of experiments conducted with dyed fluids in transparent systems suggests an analogy between unstable miscible displacement and turbulent flow in a pipe. In both cases there are fluctuations around a simpler, mean flow behavior. An important difference is that flow behavior of interest in the porous medium is entirely transient, contained within a transition zone between displacing and displaced fluids. Transient behavior complicates description in that coefficients in the equations become variables rather than constants. In the study reported here, the analogy with turbulent flow has been used in treating unstable miscible displacement as a quasi-turbulent displacement process. The purpose has been to derive, even if restricted to an idealized conceptual model, a unified theoretical relationship applicable to both stable and unstable displacement. A relationship meeting these specifications up to moderately adverse viscosity ratios, such as 17:1, is presented. One fluctuation parameter in the theory and dispersion coefficients are obtained by empirical means. The idealized theory is compared with experimental results. UNSTABLE MISCIBLE DISPLACEMENT AS QUASI-TURBULENT DARCY FLOW The miscible displacement of one fluid by another within a porous medium is considered in this study. Flow conditions are such that Darcy's law is applicable. It is further assumed that, by the stability criterion proposed by perrine,1 initial flow conditions lie well within the regime of instability. Thus substantial viscous fingering is assured. We wish to show how this flow regime can be represented as quasi-turbulent. That is, the Reynolds number for the established flow conditions is below that for inertial or turbulent flow within a porous medium, and lies within the regime for which Darcy's law is valid. Yet flow behavior can be described as the combination of some relatively simple average result, and characteristic fluctuations that are superimposed on the simpler behavior. Stated another way, flow behavior includes the movement of layers of fluids with different velocities past or over one another. Such descriptions are characteristic of turbulent pipe flow. The fluctuations in the present case are a direct consequence of the local viscous fingering which accompanies the unstable displacement process. Should displacement become stable, fluctuations would die out. It is of particular importance to note that fluctuations such as these can interact in a way that contributes to material transport by the basic flow. The basic transport equations required for engineering calculations must be modified to reflect this fact.

A failure of the Pit IA highwall in July 1989 led Newcrest Mining Ltd's Telfer Gold Mine to commence underground operations approximately 12 months ahead of schedule. The failure presented four major challenges to management: 1. how to maximise the recovery of the Middle Vale Reef (MVR) in the open pit: 2. how to minimise the risk to personnel involved in the extraction of the remaining open pit ore; 3. how to avoid disruption to ore supply: and 4. how to maintain a permanent and safe means of accessing the underground operations from the base of the pit. The risks associated with meeting these challenges were minimised through the installation of a complex network of real time slope monitoring equipment. These monitors were connected to an alarm system which was combined with detailed operational procedures to be carried out in the event of a highwall alarm being triggered. The accuracy with which the risk of failure has been managed was demonstrated recently when the onset of a second failure was initially identified some 13 months prior to its ultimate collapse in October 1992. The location, timing and size of the failure was able to be predicted allowing appropriate precautionary measures to be taken to ensure safety of access to the underground portal and pumping equipment in the base of the pit. This paper reviews the sequence of events leading to both the July 1989 and October 1992 failures of the Pit 1A highwall and the monitoring equipment and procedures used to identify, quantify and manage the risk to personnel operating in the base of the pit.

Jan 1, 1994

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

By D. E. Peacock, B. Harris

The mechanical behavior of a niobium (columbium)TUNG alloy containing 20 wt pet Ta. 15 wt pet W, and 5 wt pct Mo has been studied in the temperature range 77° to 423°K. All specitrzens tested, apart from those into which oxygen was introduced deliberately, were fully recrystallized at 1500°C, had an average grain diameter of approximately 0.03 mm, and a combined carbon, ox-vgen. nitrogen, and hydrogen content of not not more than 250 ppm The meckatnical behavior of this alloy was found to be similar in seine respects to that of unalloyed bcc transilion metals. Both yield and flow stresses were sensililae to changes in deformation rate and both increased rapidly as the temperature was lowered below 150°C. A detailed examination revealed, however, that most of the temperature dependencc of the yield stress could be accounted for by the temperature dependence of the elaslic, modulus, whish is not true of the unualloyed metals. In lension at moderate strain rates, the trunsition fvom ducfile to hvittle behavior occurred just belour room teunperature bur incveasing the oxygen content from 190 to 200 pptn raised the transition temperature to about 4000K. TUNGSTEN and molybdenum have been found to be very effective high-temperature solid-solution strengtheners of niobium, but the amounts of these elements that can be added are limited if the alloy is to retain useful room-temperature ductility. It has been shown, however, that partial replacement of niobium with tantalum lowers the ductile-to-brittle transition temperature of such alloys and allows larger additions of molybdenum and tungsten to be made. Some of the high-temperature properties of niobium alloys containing these elements have been reported by Bartlett et al.,' and the work presented here describes the low-temperature behavior of one of these, a solid-solution alloy containing, by weight, 20 pct Ta, 15 pct W, and 5 pct Mo. The elastic modulus, the temperature and strain-rate dependence of the yield and ultimate tensile stresses, and strain-hardening effects are discussed and compared with those of unalloyed niobium. EXPERIMENTAL MATERIAL AND PROCEDURE The material used in this investigation was produced from a 6-in.-diameter, double arc-melted ingot. This was can-extruded at about 1150°C to a 3-in.-diameter billet, and after annealing for 1 hr at 1345°C the billet was heated to 1315OC and part rolled and part forged to 0.5-in.-thick plate. The resulting material exhibited a cold-worked structure

Jan 1, 1965

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By John K. Gustafson

The title of my talk is "The Gold Miner and the Future of Gold." This title might just as accurately have been stated as "Gold and the Future of the Gold Miner." Since prehistoric times gold has been sought by mankind for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value and lubricated trade between peoples. For at least 6000 years, gold has been used to barter for other commodities. It has been prospected for, treasured, made into works of art and personal adornment, and from time to time has been the object of conquest. Because of its predominant role in recent centuries as a basis for money, economists began to think of it solely in these terms. Annoyed by the disciplinary pressure of gold on the money manager's desire to manipulate money, the famous economist, John Maynard Keynes, characterized it as a "barbaric relic of the past", a characterization repeated by William McChesney Martin, Jr., when he was head of the Federal Reserve Bank. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world.' It is the most ductile metal known. An ounce of gold, for example, can be drawn into a continuous wire over 35 miles long. It also is so malleable that an ounce of gold can be beaten into films ten one-millionths of an inch thick sufficient to cover 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of gold weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity, only slightly less than silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity both to light and infrared rays. Because of these qualities, in addition to its rare beauty, industrial and artistic uses of gold have been growing rapidly. On a world basis, a recent study estimated that in 1960 about 750 tons of gold were used for fabrication, and that the amount had grown to about 1296 tons in 1968. My objective in this talk is to discuss with you the present and future supply of and demand for gold on a worldwide basis and the effect these forces are likely to have on the price the miner can expect to receive for the gold he produces. This is a highly controversial and risky subject to discuss before any audience. Nevertheless, it is a subject that I live with constantly as Chairman of the

Jan 1, 1972

By P. A. Verhey

"This paper describes a series of wear-resistant ceramic materials which have been successfully used in the mineral processing industry in Canada. Applications include use with metallic ores, coal, potash and asbestos, and in other processes where wear degradation is of major concern. The paper will also deal with considerations involving the selection of the different ceramic materials available. It will cover the installation of ceramic materials on support structures under varying process ' conditions, as well as the other physical and chemical factors which have to be taken into account.IntroductionIn the mineral processing industry, large volumes of ores tailings and other materials are handled. The abrasive nature of most of these materials results in extensive wear to both handling and processing equipment.Wear ratios versus cost, production losses due to down time and wear-resistant material suitability for a given application all demand particular attention when viewed against the need for increased efficiencies in existing processes. As a consequence, a very active continuous search for materials with improved wear resistance has been carried out for many years.In this search, starting about 20 years ago, dense ceramic materials were tested and evaluated in certain applications, notably in the iron ore and asbestos operations in Eastern Canada. As a result of substantially better performance both in continuous extended life and ultimate economics realized , wear-resistant ceramic applications developed progressively in many other processing applications, replacing traditionally used materials.In the vast majority of wear-resistant ceramic applications, considerable extended life over previously used materials was established. This invariably was not just a fractional increase but, in most cases , in factors of double, triple and often all the way up to 18 and 20 times the life of alternative materials used previously. In certain applications, extended life could not be measured and appears to be indefinite.Obviously, as a result of such experiences, the progressively wider use of wear-resistant ceramic materials is now an established trend."

Jan 1, 1981

By William E. Greenawalt

Ever since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydroelectric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods. Electrolytic methods are ideally adapted to hydroelectric development, for the load is constant throughout the full twenty-four hours, and the cost of both installation and operation of hydroelectric plants is not appreciably greater when operating for twenty-four hours than when operating for eight or ten hours; whereas, in fuel-power generation, as also in smelting, the cost is more or less in proportion to the fuel and power used. Nevertheless, fuel-power generation presents advantages in electrolytic methods, as the power plant may be located in a favorable place while the leaching and electrolytic plants may be located at the mine. The ultimate possibilities of the wet methods have yet to be determined. The possibilities of smelting have been thoroughly worked out; there is no unsolved major problem in copper smelting, and it has practically reached the limit of its possibilities. It seems hardly probable that any future improvement, either of method or apparatus, will greatly

Jan 1, 1924

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

Power cable costs are only a small part of total mining costs. So many mine operators consider power cable failure and resultant downtime as part of the cost of doing business. But, viewed in terms of lost production, these costs can be quite significant. Now one company, Cablec, seeks to cut cable costs by upgrading the polymer compounding process used to make cable insulating and semiconducting materials. Cablec is the leading manufacturer of electrical power cables in North America. And with about a third of the market, Cablec is the largest supplier of power cable to the mining industry in the United States. To improve its products, Cable has entered the polymer compounding business. In July, it began producing insulator and semiconductor polymer compounds at its plant in Indianapolis, IN. "This new facility provides a quantum leap over conventional compounding methods," said Harry C. Schell, Cablec's president and chief executive officer. "The Cablec polymers plant is producing a dramatically higher standard of polymer compounds that provide significantly higher levels of performance and improved life cycle costs for power cable." Cablec faces tough foreign competition in the wire and cable business. Competing on price alone is difficult, particularly when foreign producers are state subsidized. So Cablec feels the best way to compete is to establish new quality production standards. The company's new polymers plant is one way to do this. By increasing purity control and uniformity in polymer compounding, Cablec says its power cables will last longer and fail less often. A typical medium voltage cable consists of a conductor, conductor shield, insulation, insulation shield, metal shield, and jacket. The conductor shield and the insulation shield are conducting polymers. Contaminants and imperfections can occur within the insulation, at the conductor shield/insulation interface, or at the insulation shield/ insulation interface. Over time, these contaminants and imperfections can decrease the electrical strength of the cable or cause premature cable failure. The effort to minimize the number and size of any possible contaminants begins with pure polymer compounds mixed in a clean facility. However, most power cable manufacturers manually handle raw materials, use ethylene/propylene (EP) in bulk bales, and mix polymercompounds in open Banbury mixers. The quality and uniformity of polymer compounds is also impacted by temperature variations in the mixing process. This results in wide gradations of product consistency from batch to batch and ultimately contributes to power cable failure. Cablec says the improved polymer compounds from its state-of-the-art plant will be the purest and most consistent insulating and semiconducting materials available. The plant itself RCA spent $18 million to build Cablec's Indianapolis plant. RCA used the facility to mix specialty polymer compounds used to make video disks. RCA had two considerations in mind for the plant, cleanliness and uniformity of the compounds. However, when the video disk market failed to materialize, RCA sold the 46.5 dam 2 (50,000 sq ft) plant to Cablec for $3.1 million. Cablec invested an additional $3 million for modifications and increased production capabilities. Today's replacement cost for such a facility is estimated at $30 million. Cablec says the plant will set a new standard for performance and be economically difficult to duplicate anywhere. One of the essential elements of the plant's clean process environment is the air intake system. It filters contaminants greater than 2 um, less than one-fiftieth the current industry standard. All material handling and conveying areas in the facility are air-locked. This keeps out contaminants such as smoke, dust, and pollen. Banks of pneumatic pumps move polymer components through the system and continually filter the air. The plant also has a backup air intake system. No process downtime due to pump failure here. From the time raw material enters the plant, it is stored, transported, and processed in filtered air by an airtight stainless steel system. The stainless steel resists rust and corrosion. This further eliminates the danger of contamination from paint or rust particles in the conveyance network. A computer system allows a single operator in a central control room to monitor every aspect of the compounding process from air quality to line speed. The computer

Jan 12, 1988

By E. J. Garrison

Discussion by E.J. Garrison A.C. Noble presents a clear and concise summary of the factors pertinent to a competent reserve evaluation of a mineral occurrence. However, I believe that he confuses the difference between a resource and a reserve. By definition, a reserve estimate includes all known economic, legal, mining, metallurgical and environmental factors impacting the recovery of the product(s) found in the deposit. A resource estimate, however, is an estimate of what is there - what is available for exploitation and should not include economic and other considerations. Only after defining the resource, its extent, location, physical and chemical properties, can an intelligent selection process begin of the extraction and processing technologies most appropriate to the circumstances encountered. The early and almost certainly inappropriate application of these often cookbook choices has probably lead many companies to walk away from good properties. (How many mines have been found in others rejects?) An example of the process is the early selection of metallurgical samples, after encouraging values are found in a few holes or surface samples, in an attempt to determine the economics of the prospect. Unfortunately, the sampler does not know how representative of the occurrence the sample is because he does not know what the deposit looks like. As a consequence, the property becomes saddled with a bad metallurgical sample that is often inappropriately used in evaluating the deposit which it does not represent. Reply by A.C. Noble E.J. Garrison asserts that I confuse the difference between a resource and an ore reserve. In fact, this paper was motivated by the observation that resources and reserves are almost universally confused throughout the industry. While Garrison is concerned that too-early consideration of engineering, metallurgical and economic factors will result in dropping properties too soon, some issues that must be considered include: •The purpose of exploration is to discover ore reserves, not to discover resources. •Ore reserves are always smaller than resources. • Decisions on exploration expenditures must be made based on the expectation of the quantity of ore reserves that will ultimately be defined. Noble's Fig. 2 can be used to give guidance as to when it is appropriate to begin reserve calculations. When exploration enters the "flat" portion of the curve, representative samples can be selected for metallurgical studies and appropriate mining methods chosen. It is at this stage that we know enough about the deposit to make intelligent choices of representative samples and recognize constraints on mining caused by the deposits shape, environment and physical properties. Once the appropriate technologies have been chosen, then their cost can be estimated with reasonable accuracy. Early entry of economic and process factors gives the false appearance of reserve status to the resource estimation. It would be more informative and less subject to abuse and misunderstanding if resource calculations were made at a number of cutoff grades. The cutoff grades should be chosen to cover the range of grades found in practice in existing operations of similar type. This would emphasize the open nature of resource estimates and encourage creative evaluation of mining and process technologies. It does not preclude the use of economic, environmental and recovery technology factors in deciding the advisability of continuing exploration expenditures, but would highlight their speculative nature. It is thus hoped that decisions on the future of the deposit would not be made on the presumed suitability of a given technology but on the actually known reality. I agree that resource estimates should be reported as a range of cutoff grades. Since reporting at a cutoff implies application of underlying economics (even by analogy to similar properties), however, it should be clearly stated that resources do not consider economic, mining or cost factors, and that ore reserves will be substantially less. The dilemma of the explorationist is that until the continuity and limits of ore-grade mineralization have been established, it is difficult to make quantitative estimates of either resources or ore reserves. Further industry discussion is needed regarding standards for disclosing early exploration information in such a way as to fairly represent the potential of an exploration property.

Jan 1, 1995

By Joseph E. Worthington

The present-day Northumberland gold mine is one of the deposits generally characterized as a Carlin-type occurrence. It lies at the crest of the Toquima Range in Nye County near the center of Nevada. Gold mineralization occurs in two modes, in argillaceous and in silicified limestones, and is generally very fine-grained or micron gold. The Northumberland district has had a history that is typical of many western gold districts: minor production prior to World War II and intermittent exploration thereafter until a combination of geological insight, improved economics, and the advent of heap leach technology created the Northumberland gold mine. Nye County, Nevada, was sparsely populated and little explored in the early years of the settlement of the west; the Northumberland district was not established until 1866. Initial interest was in silver and the district operated as a very small producer for the next seventy years. The disseminated gold occurrences in silicified limestones were recognized and Northumberland Mining Co. was organized to develop the property in the late 1930s. Northumberland Mining Co. actually conducted drilling operations (over 200 drill holes) and mined from small open pits in the silicified limestones. They ultimately produced almost 936 kg (33,000 oz) gold before being shut down by War Production Board Order L-208 in 1942. After World War II gold mining activities were essentially nil for over a decade due to the poor economics of gold production. The property was, however, a known gold producer and attracted recurrent exploration attention. About 45 holes were drilled under the direction of Peter Joralemon for private interests between 1959 and 1963. Next Kerr McGee drilled about 25 holes during 1963 and 1964. Some- what later, in 1968, Homestake drilled 20 holes. The property was then acquired by Idaho Mining Co. which drilled about 30 more holes between 1972 and 1974. By this time the Northumberland mine was becoming somewhat shopworn with over 300 holes drilled. Interest in gold prospects was increasing substantially in Nevada, how- ever, due to rising gold prices in late 1974, and several companies were interested in continuing exploration at Northumberland. In 1975 Cyprus Mines Corp. was successful in obtaining a joint venture arrangement with Idaho Mining Co. for further exploration and development of the property. The overall Cyprus exploration program was under the direction of James G. Hansen, Vice President Exploration. The geologist recommending acquisition of Northumberland was Peter E. Chapman who reported to Joseph E. Worthington, Manager of U.S. Exploration for Cyprus. The basis for selection of the Northumberland mine as an exploration target for Cyprus by Chapman was essentially prior knowledge of regional and 16cal geology and of the mine. Exploration for the next few years was directed by Chapman under the supervision of Worthington. During 1975 and 1976 rotary and check core drilling were conducted that indicated that a substantial Carlin-type or disseminated, low-grade gold deposit occurred in two separate bodies. Drilling was based on geologic mapping and rock chip geochemical sampling. Both ore zones were reflected at the surface as gold and arsenic anomalies in rock chips. Heap leach tests attempted in 1977 were aborted by a flash flood, but were completed in 1978. Engineering studies occupied the next couple of years until the property achieved production in the fall of 1981. It is now producing by open-pit mining with gold recovery by heap leaching and cyanide extraction at a rated capacity of approximately 2722 t/d (3000 stpd) ore. Metal recovery has been projected (probably conservatively) at 5 10 kg/a (18,000 oz per year) gold and 1.6 Mg/a (59,000 oz per year) silver. Reserves are reported to be adequate for ten to fifteen years of production. REFERENCES Anon., 1981, "Gold in Nevada," Span Magazine, Vol. 21, No. 3, Standard Oil Co., pp. 6-9. Koschman, A.H. and Bergendahl, M.H., 1968, "Principal Gold- producing Districts of the United States, Professional Paper 610, US Geological Survey, p. 193. Kral, V.E., 195 1, "Minerals Resources of Nye County, Nevada, Bulletin, Vol. 45, No. 3, Geology and Mining Series 50, Nevada University.

Jan 1, 1985

By Jack A. Simon, M. E. Hopkins

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

By G. R. Sadowski

"Large subhorizontal joints have been found in the foundation excavations in basalt and granite of Brazilian Dams. Some spread for hundreds of square meters showed slickensides—polished surfaces plus striations—and laminations interpreted as related to shear displacement, what substantially reduced their shear strength and imposed special reinforcement measures against the potential sliding of overlying concrete structures. The geological characteristics of these discontinuities have raised speculations related to their origin, be it related to mechanisms of bulging, cambering or to some tectonic or primary geological event.Several geologists and engineers from the northern hemisphere including Terzaghi already showed to be concerned with their role in granite foundations while in the southern regions Brazilian authors have found similar occurrences but also affecting individual lava flows of continental flood basalts in the foundations of major dams of the Parana Basin, which they designated under the particular name of “fault-joints”. This double-standard designation is self-explanatory of the difficulties involving their origin and related geomechanical properties: faults or just shear joints?Recently, similar features were encountered in the foundations of large dam constructions in anorogenic granites inserted in the realm of the Brazilian Amazon, where some of these discontinuities exhibit features common to tectonic thrusting combined with deep tropical weathering.The evidence of preshearing along the surfaces of such fractures, also associated to products of deep weathering, reduces their geomechanical strength substantially, suggesting values of ultimate phi spanning 12 to 28°. The detection of these descontinuities during initial investigation phases continues to be a major complex task in geological risk evaluations surveys. Trenching associated to some geophysical exploration techniques, although considered to be very basic exploration techniques are still the suggested methods for their forecast and previous determination."

Jan 1, 2015