Search Documents

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By L. Donovan Clark

The term "powder factor" is almost universally accepted as the measure of the efficiency of a blasting program. It represents the economics of blasting since it designates quantity of explosive (thereby providing quality control in rock fragmentation) in terms of the associated volume broken. It is the wide use of this concept that explains the interest shown in an approach to rock blasting preferred by A. W. and Z. W. Daw* in a treatise on 3 blasting (1) substantiating its use in the form, Q = CVW3 for single shot hole, where Q = quantity of explosive lb Cv = blasting coefficient W3 = unit volume of rock It is obvious that the term Cv could also be called the apparent powder factor should the equation be written in the form, Cv = Q/W3 (lb per cubic unit). However, while the approach was ingenious** and the practical applications straightforward, their original, rather limited experimental work, along with certain assumptions, was questioned.

Jan 1, 1970

By F. L. Pirkle, W. C. Bagby

"In his 1989 book, The New Realities, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, Claremont, CA, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized” (p. 209).The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze and interpret data that are material to a mineral-valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral-valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality and transparency, the three pillars of mineral valuation (minerals valuation, mineral-property valuation).The International Mineral Valuation Standards Template (IMVAL Template), third edition dated May 2018, defines mineral valuation as: “The estimation of the value of a mineral property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the valuation conclusion) or to refer to the preparation of the estimated value (the act of valuing)” (p. 14).Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The template deals with valuation, which is distinct from evaluation. The distinction inherent in these defined terms is that valuation addresses the estimation of value of a mineral property, whereas evaluation addresses the broader assessment of a mineral property for an investment decision (p. 2).”This is an important difference because the minerals industry commonly makes investment decisions using feasibility studies to evaluate a proposed mineral development and production project. The purpose of such investment-decision analysis is distinctly different from valuation of a mineral property, no matter where that property lies upon the mineral explorationdevelopment- production-reclamation timeline (Fig. 1). Valuation involves terms such as market value, just compensation, fair value, etc., whereas investment-decision analysis is concerned with the economic viability of a given proposed project. Although feasibility analysis and market valuation can both use discounted cash flow (DCF) analysis as a tool, the formulation of the DCFs and their interpretation are different."

Nov 1, 2019

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By Ross W. Seedsman

The logical framework recognises that a coal mine roof can be intrinsically stable or may collapse in one of four ways. Suspension of the immediate roof is one of fundamental ground control strategies available to a coal mine engineer and is recommended for three of the four collapse modes. Correctly implemented suspension offers the greatest improvement in roof stability and greatest reduction in longwall risk. For the control of maingates ahead of retreating longwall faces the ideal suspension support (if required) consists of angled, partially debonded, medium-length tendons installed as far behind the development face as practical. For situations where the roof may be subjected to tensile horizontal stress, immediate support by equally spaced short vertical tendons is required. The step away from fully-grouted tendons improves their survivability during the onset of compressive failure in the roof, minimises the risk of isolated loading, and allows a more robust TARP for roof movement. All suspension systems require a strap, sling or truss between the suspension elements.

Jan 1, 2014

In considering the organization of research, it is necessary to know just what research is, what objects are in mind when setting out to conduct research, and what are the functional units which are required to enable a coordinated effort in research to proceed.The dictionary defines research in the following terms: Laborious and patient search, as for truth, diligent inquiry or examination in seeking facts or principles; inquiry, scrutiny; to search or examine with continued care; to seek diligently; to search again; to examine anew.This is, of course, simply a formal definition, but the reference to "labour", "patience" and "diligence" should be noted.The following quotation from an answer to the question "What is Research?", published recently in a technical journal, puts some life into the formal definition:- Essentially, it (Research) is nothing but a state of mind a friendly, welcoming attitude toward change. Going out to look for a change instead of waiting for it to come. Research, for practical men, is an effort to do things better... The research state of mind can apply to anything: personal affairs or any kind of business, big or little. It is the problem-solving mind as contrasted with the let-well-enough-alone mind . . . It is the "to-morrow" mind instead of the "yesterday" mind. Note the statements that: Essentially, it (Research) is nothing but a state of mind, and the research state of mind can apply to anything.

Jan 1, 1950

By Earl Cook

A high-energy economy based on fossil fuels is in fundamental conflict with an ideal of clean air, clean water, undisturbed scenery, and maintenance of fragile ecosystems. There is an inevitable trade-off between the material standard of living of a modern society and the conservation of its environment. During the past four years, some of the costs of environmental protection have been internalized in the energy-flow system of the United States. The cost of bituminous coal and fuel oil usable under new air-quality standards has doubled or more. The cost of mining coal underground has risen because of a 20-30 percent reduction in productivity resulting from new environmental health and safety legislation; the economic impact of proposed surface-mine regulation may be equally severe. The cost of producing electric power has been rising at a 12 percent annual rate because of environmental costs, and would be climbing still more steeply were it not for the continued forced subsidy of natural-gas consumers by natural-gas producers. The efficiency of the automobile, already a monument to the triumph of self- indulgence over economy, is being further decreased by addition of anti-pollution devices. Part of the recent sharp rise in agricultural costs stems from the fact that five energy units of fossil fuel go into U.S. agriculture for every energy unit of raw food that leaves the farm; further large injections of fossil-fuel energy occur in the transport, processing, and refrigeration of farm products.

Jan 1, 1974

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015

By T. Krumins, L. Zunti, R. Frischmuth

Mercury is known to occur in sulphide-bearing refractory gold deposits in the form of sulphide minerals or elemental inclusions. These deposits typically require an oxidative pre-treatment process, such as pressure oxidation or roasting, to achieve economic gold recovery. However, these processes also have the potential to liberate mercury, a portion of which may then be released to the environment through gaseous emissions. Mercury emissions from mine processing operations have been of particular interest in recent years, as governments impose lower emission targets and organizations adopt better industry practices to reduce the environmental and health aspects of releasing mercury into the environment. This paper describes various mercury removal technologies with respect to pressure oxidation gas handling circuits, with a focus on key design variables and technology selection criteria.

Jan 1, 2014

By P. I. James, M. R. Baker

This paper examines new copper production from waste-grade ore using Blue Planet Strategies’ DEMET™ (Dynamic Electrode Mining Effluent Treatment) technology, which aims to bridge the practical weak pregnant leach solution (PLS) processing gap in heap leach-solvent extraction/electrowinning (SX/EW) operations by electrochemically removing metals from weak streams and generating product streams strengthened in target metals in a functional analog to SX. Weak PLS treatment was studied and used to estimate the economic and production impacts for a representative hypothetical brownfield copper heap leaching and DEMET-augmented SX/ EW operation to utilize "waste ore." Copper removal at 86% plating efficiency to below 0.1 g/L copper with power consumption of 0.55 kWh/lb copper and product strengths of over 10 g/L copper are presented. Modeling yielded approximately $2/lb total copper production and = $1/lb treatment costs with an immediate operation gross margin increase of 12% for the augmented brownfield. Potential mine life extension with an average 38% gross margin on "waste ore" augmented production at copper values of $3.25/lb was also indicated.

Jan 1, 2014

By P. -M. Tardif, S. Outalha, R. Le

"This paper proposes a new direction to implement an underground mine communication system. It presents actual underground communication systems and discusses their technological limits. A new system based on a wireless local area network (WLAN), together with its main systems characteristics, is then proposed. This paper also presents an experimental protocol for radio frequency propagation measurements. Finally, the paper describes the projected implementation of a WLAN in an experimental mine. IntroductionDuring the last decade, a number of Canadian mining companies have invested in modern communications systems in order to automate processes and reduce operational costs. Safety of miners is also a concern, regulated by health and safety regimes.Underground communication systems rely mainly on analog technology (especially the leaky feeder). Digital upgrades have been made to modernize this technology using a coaxial or fibre optic cable to transmit voice, documents, commands, controls, and video. Therefore, all wired equipment can benefit from an increase in efficiency from the digital technology.However, when it comes to mobile equipment, the only medium was, and is, still radio waves. With the advent of the wireless local area network (WLAN) standard, one can use a technology similar to that of the cellular phone to connect transparently different equipment. WLAN enables the transmission at rates higher than 2 M bits of voice, documents, commands, controls, identification, and of course, digital video. This technology was developed with inbuilding use in mind. Now, one can try to adapt it to underground mines."

Jan 1, 2000

By D. A. Karvonen

In 1970, the Government of Saskatchewan instituted a program aimed at resolving the dilemma of excess productive capacity over the market demand which existed for potash produced in Saskatchewan. The two primary elements of the program were prorationing of potash production to market demand and a minimum selling price. The paper reviews the factors, both local and international in nature that led to the introduction of the program. The licensing mechanics and the operation of the program, along with the changes that have been introduced in two and one-half years of operation, are discussed. Attention is given to the results of the controls as they affect the industry and the province. Also discussed is the outlook for Saskatchewan potash in world markets.

Jan 1, 1973

By C Beal

Proper understanding and management of production drilling in sublevel cave (SLC) mines is essential for meeting production targets and for avoiding inefficiencies that could lead to costly bottlenecks. In many SLC mine management models drilling is considered a derivative activity of firing and bogging. Its scheduling is considered to be implied in a firing schedule and given an arbitrary target completion, ‘several weeks’ or ‘a month’, ahead of production firing. Like development, drilling activities are most efficient when conducted separately from other production activities. Unlike development, however, it is not apparent during planning and feasibility how far in advance of firing drilling activities ought to be conducted. This paper presents a method of defining a minimum threshold of drilled stocks above which drilling, firing and bogging operations occur most efficiently. As an example, the drilling activities, procedures, and maintenance at Glencore Xstrata’s Ernest Henry Mine are presented, and the larger scale consequences of improvements to these areas are presented to illustrate their importance in the operation of an SLC mine.CITATION:Beal, C, 2014. Understanding the role of production drilling and drilled stocks in efficient operation of a sublevel cave mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J. W. Senn

A magnesium alloy modeled after commercial alloy WE54 was thermomechanically processed and characterized to understand the mechanisms by which its texture can be randomized, as reported by Ball and Prangnell [1]. Samples were deformed in plane strain compression to prescribed strain levels at temperatures high enough to prevent cracking and then recrystallized. The deformation texture is very similar to that observed after plane strain compression (e.g., rolling) of other Mg alloys, such as common AZ31. However, the texture can radically evolve during recrystallization. Annealing above the precipitate solvus temperature results in a nearly random recrystallization texture where the initially strong basal texture is completely eliminated. Annealing below the solvus temperature produces a recrystallized texture similar to conventional Mg alloys, i.e., a weakened basal texture. If this same material is then annealed above the solvus to promote grain growth, a randomized texture evolves, which is similar that of samples simply recrystallized above the solvus. It is hypothesized that a sort of preferred growth mechanism, whereby grains with random orientation grow faster than those with the original basal texture, contributes significantly to the texture randomization observed in wrought magnesium alloys containing rare earth elements.

Jan 1, 2006

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By E. L. Litchfield

Four short-term studies of practical ignition problems were undertaken and completed during the course of the Bureau of Mines project "Development of Specifications for Intrinsically Safe Equipment." Conclusions were as follows: (1) the most easily ignitible mixture of propane-air in a PTB break flash apparatus is approximately 5.2 percent propane; (2) miniature lamp bulbs to be used in intrinsically safe circuits are about as incendive to coal dust-air as to methane-air and should be tested in gas mixtures containing about 7.0 to 7.5 percent methane; (3) the sodium amalgam contained in high-pressure sodium lamps does not present an ignition hazard for coal dust or methane, where the lamps contain no more than 30 milligrams of amal-gam; (4) the maximum allowable surface temperature of permissible electrical enclosures should remain at 150° C despite efforts by industry groups to raise the value to 200° C.

Jan 1, 1980

By Joseph E. Worthington

Increases in the price of gold starting about five years ago, and rapid fluctuations since then, have caused a substantial popular interest in the noble metal. Gold prospecting had been at low ebb since the end of World War II in most of the United states except for a flurry of activity in Nevada occasioned by the Carlin and Cortez discoveries. The last five years, however, have seen a great awakening of interest in gold exploration as well as an opportunity for education for many explorationists in the geology and other vagueries of gold deposits. The present writers have participated over the last few years in a search for gold deposits throughout the United States. This search was greatly influenced by the geologic studies of Dr. Wm. Spence at the Haile Gold Mine in South Carolina as reported in a companion paper. Spence's studies resulted in definition of a geologic model that has proven useful in a number of other geologic environments in the united states. These programs were all carried out under the auspices of Cyprus Mines Corporation and permission by Cyprus to present these results is gratefully acknowledged. The writers, however, reserve for themselves all responsibility for the results and conclusions. The exploration program to be described began in the southeastern United States. Spence's studies provided a reasonable basis for interpreting and understanding the geology of the Haile deposit and also provided a means for predicting additional occurrences. This concept was then expanded to other gold occurrences in the Piedmont and became an effective tool for evaluating other prospects. Finally it became evident that the concept could be applied in some western gold districts. The following discussion will then include descriptions of other Piedmont examples and a few western districts that also appear to fit the pattern.

Jan 1, 1978

By S. Frisch

Selenium (Se) in effluent waters has become a significant challenge for a number of industries. Toxicity studies and new reports of occurrence have certainly caused increased scrutiny and actions in the mining industry today (Sandy, DiSante, 2010). While initial activity in addressing selenium-laden waters were conducted in the coal mining industry, today a much broader range of mine types are beginning to search for solutions to selenium treatment of their mining waters, including both hard rock mining operations (gold, nickel, zinc, etc.) and soft rock mining (phosphate, uranium, etc.) Throughout North America, new regulations covering selenium discharge are either in place or being developed. While a number of physical/chemical approaches show promise in selenium treatment, when considering optimal cost and treatment efficacy issues, biological treatment ? particularly fixed-film biological treatment - is reported to be one of the most promising approaches to managing selenium-containing waters. Among biological treatment options, the fluidized bed reactor (FBR) has undergone extensive pilot testing for Se treatment in the last three years, including eight pilot programs, and the first FBR system is now operating at a coal mining site. In all tests, the FBR has been shown to be a highly cost-effective approach to selenium treatment based on its physical and performance characteristics. This is consistent with its history for reaching low levels of treatment in similar service for other oxyanions including perchlorate, nitrate and various metals. With the results from the most recent testing, the technology has been shown to be adaptable to an ever-broadening range of influent water conditions and flow rates, in varying terrains and weather conditions. Selenium occurs in various valence states from -2 to +6 (Sobolewski, 2005). The speciation of selenium plays a critical role in understanding the effectiveness of any approach for removal, especially to low levels. Elemental selenium is insoluble and has little effect on living organisms. Colloidal fractions are known to occur. In aqueous environments such as coal mining runoff, selenium is most often found as the oxygenated anions of selenite (SeO32-, Se4+) and selenate, (SeO42-, Se6+). Selenium is commonly found in mining waters in concentrations ranging from 3 to >12,000 µg/L. The U.S. National Primary Drinking Water Standard MCL is 50 µg/L for selenium (EU 10 µg/L; WHO 40 µg/L). The National Fresh Water Quality Standard is 5 µg/L for selenium. The U.S. Fish and Wildlife Service has recommended that the National Fresh Water Quality Standard be lowered to 2 µg/L to protect fish, waterfowl, and endangered aquatic species. Several states have followed with enforcement actions at these same low levels. In Canada, permits may require stakeholders to monitor levels in water or biota, or to comply with guidelines, at either the National or Provincial levels, which can be as low as 1 or 2 µg/L in surface waters. Treatment of selenium in all mining waters presents a series of challenges. It can be present in relatively dilute concentrations and in streams with variable and often high flow rates. It can be present in many soluble and particulate forms, which may affect process design and treatability. The conditions of influent selenium-containing waters can vary, with issues such as temperature, pH, total dissolved solids and other contaminants affecting the ability to remove selenium selectively and economically. Treatment of selenium often results in the generation of a concentrated by-product requiring disposal, and re-release from residuals can occur. Beyond these issues, the physical environment of a mining operation can offer challenges such as remoteness and harsh and/or cold weather. Currently available selenium treatment technology (Table 1) includes biological treatment and a number of physical-chemical processes ? such as ion exchange, membrane filtration and adsorption ? that vary widely in efficiency and cost. Most treatment options remain either too costly and/or unproven for selenium-containing streams for reasons that include poor removal efficiency, variability in volume and composition of influents, system sizing and logistics considerations, as well as operating requirements.

Feb 23, 2014

By D E. Thorp

The mining and concentration operations of New Zealand Steel have been carried out initially from the Waikato North Head (WNH) deposit since 1969 and subsequently from the Taharoa deposit since 1972. Over the years the WNH operation has produced about 1.2 million tonnes of concentrate which has been converted into steel, while total exports to the Japanese Steel Industry from Taharoa reached five million tonnes in February of this year. Recent expansion plans both in domestic steel production and in the ironsand concentrate export market have made it necessary for the company to look closely at, among other areas, the mineral processing of the titaniferous ironsands in both deposits. This paper deals with the recent test work carried out at WNH and Taharoa on the use of the cone concentrator unit as a primary gravity concentrating unit ahead of the magnetic separation stages and as a cleaner concentrator following the primary magnetic separation.

Jan 1, 1977

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996