Search Documents

By A. I. Collins, D. Danninger

Newmont has installed advanced control and online optimization on the dry grinding circuit and both roasters on its Carlin Trend refractory ore treatment plant. Subsequently, Newmont has developed a master plan for institutionalizing advanced control and optimization on all its processing units. Newmont is committed to a program of applying advanced control and optimization from crushing of ore to pouring of gold. This paper describes Newmont's experience with implementing advanced control and optimization and the benefits received. In addition, identification of advanced control and optimization opportunities and their economic justification is discussed.

Jan 1, 2005

By T Peters

The Kibali Gold Mine is currently comprised of several open pits, a 3.5 Mtpa underground mine and a 7.5 Mtpa processing plant. Development of the underground operation commenced in December 2012, with initial access established through twin surface declines, followed by the commencement of a blind sink 8 m diameter rock hoist shaft in March 2013. Stope production started in December 2014 with ore and waste trucked to surface. The 755 m deep blind shaft sink was completed in August 2015 together with the cutting and equipping of three main station levels. Two of these levels provide access for the establishment of the underground materials handling system as well as the main dewatering system for the mine. This paper covers the process of determining the optimal location of the Kibali hoisting shaft relative to project-specific critical factors, and then focuses on the design and implementation journey associated with the off-shaft development that essentially encompasses the Material Handling System (MHS) for the mine. The journey starts from the findings of the previous owners Feasibility Study (FS), a subsequent Optimised FS, followed by detailed engineering through to implementation. It was identified during implementation that a significant change in the designed off-shaft layout was required following detailed underground geotechnical and hydrogeological investigations. In addition, the paper provides details on the MHS performance since commissioning to steady state, and on key learnings relating to the overall project process.

Mar 29, 2023

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By Jerry Luttman, Mark Dubay, Anvesha Dogra, Elizabeth Dwyre, Wei Hu

The I-75 Modernization Project (Segment 3) just north of Detroit, MI is being delivered as a Design-Build-Finance-Maintain (DBFM), which is a Public Private Partnership (P3). The project includes design and reconstruction of 5.5 miles of freeway, including a depressed section with a 20,630-ft long, 14.5-ft inside diameter, up to 100-ft deep stormwater tunnel, multiple drop shafts, and a pump station. The project also includes a maintenance term of 25-years. This is the first time MDOT has used a P3 delivery method for a major highway and tunnel project. This paper describes the development of the P3 documents, including performance-based tunnel and shaft technical requirements, and the approach to project risk management, financing, and insurance coverage.

Jun 23, 2024

By Stuart Hardy, Xiangbo Qiu

The South Bank Place project comprised the redevelopment of the iconic Shell Corporation headquarters in Waterloo, located on the Southbank of the River Thames in central London. The site was originally developed in the 1950’s and due to the monitoring of the underlying Bakerloo Line tunnels by the Building Research Station it has become a seminal case history for the long term swelling behaviour of London Clay. The redevelopment, undertaken by a joint venture of Canary Wharf Group and Qatari Diar, included demolition of the existing building (with the exception of the main towers) retention of the existing basement structure and the construction of eight new mixed use buildings, up to 31 storeys in height. The foundations for the new buildings varied according to the building height and the below ground constraints. Two of the buildings are partially founded in reused under reamed piles that were installed as part of the original 1950’s development. The paper describes the novel methodology developed to assess the re-use of the under reamed piles which builds on the guidance published by CIRIA and the BRE for straight shafted piles. The paper also describes the physical investigations and numerical analyses undertaken as part of the assurance process and the procurement of latent defect insurance by the client.

May 1, 2022

By Bartho J. Admiraal, Antoine Feddema

Pneumatic sinking of caissons has been established from mid-19th century. The technique of pneumatic sinking has been applied on many projects for underground construction up to depths over 20m below groundwater level since that time. Volker Staal en Funderingen, a known deep foundation contractor in the Netherlands, was awarded two contracts in 2015 for sinking in total 2 caissons in Hamburg (Germany) to large depths (over 30 m (100 ft) and two projects near Amsterdam (the Netherlands). The latter concerned two gate chambers for the world’s largest sea-lock, one of them was 55x81 m2 (180x266 ft) to a depth of 25.5 m (84 ft), which would mean a world record for pneumatic sinking! But with depths and dimensions like these, the deployment of personnel is the main limiting factor for production, despite all developments to date. It was decided to develop a remote controlled process, including the necessary equipment and monitoring systems. Monitoring not only the kinematics of the equipment in the working chamber and the production parameters related to the excavation but also of the structural behaviour of the sea-lock gate chambers was essential for approval of this innovative execution method. The lay-out and the sizes of the largest caisson the structural integrity was extremely critical for torsion and bending moments. A displacement controlled execution by the observational method was therefore required. In engineering a new approach for modelling the semi-continuous failure mechanisms of the soil was needed to understand the sensitivity of the excavation process and to define limit values for the execution. In the paper these structural and geotechnical issues will be explained together with the experiences during the execution.

May 1, 2022

By Robson Jacinto Coelho

A equipe da Coqueria identificou a possibilidade de reduzir o Burn Loss, que é a perda de material por queima durante o processo de coqueificação. Após uma série de estudos, utilizando a metodologia Seis Sigma, identificou-se oportunidades de melhorias operacionais que trariam mais eficiência, estabilidade operacional e consequente aumento na produção de coque e vapor, tais como: maior controle na admissão de ar, controle das perdas de coque e carvão, vedação dos fornos de coque e execução de paradas programadas específicas para Preservação Refratária, com foco na redução do back log e consequente prolongamento da vida útil das baterias de fornos de coque. A redução Burn Loss aumenta o rendimento coque/ carvão, com consequente redução do consumo específico de carvão e aumento na produção de coque e vapor. A implantação desse projeto permitiu a redução de 2,5 dólares por tonelada de aço produzida no Fiscal Year 16/17.

Oct 30, 2017

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019

By Mario SINNAEVE, Olivier LEMAIRE, Gisèle WALMAG, Sébastien FLAMENT

Many hot rolling mills worldwide face nowadays bonding zone fatigue problems before reaching scrap diameter of the work rolls. This phenomenon is nowadays known to occur in reversing roughing mills both in stainless steel and in carbon steel rolling. The phenomenon can be explained through longer rolling campaigns, inadequate backup or work roll maintenance, harder steel grades or increased throughput by reduced amount of passes to achieve the same thickness. In order to help users in optimizing the roll use, we developed a numerical tool to evaluate and optimize roll maintenance. This paper will review the influence of roll geometries on stresses generated at the roll surface but also at the bonding zone. We will also show how roll geometries can decrease contact fatigue damages by modifying crowning and chamfering procedures, shell thickness, material design or campaign length

Oct 1, 2019

By W. R. Reed, W. J. Archer, A. B. Cecala, J. D. Potts

The U.S. National Institute for Occupational Safety and Health (NIOSH) uses light-scattering real-time dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer (i.e., with cyclone and pump configuration), was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By Jeffrey Shawn Peterson

In past years, the U.S. Bureau of Mines has been involved in safety research that could ultimately re-late the conditions of spark testing and actual use by estimating the simple ignition probability of a circuit in question. A major problem in estimating this probability is that results show a significant variability, even though gas mixtures and electrical parameters may be closely controlled. Some researchers have suggested that the ambient environmental conditions of the testing may influence the results. A series of tests were conducted using a spark test apparatus to simulate a failing electrical circuit. By independently adjusting the temperature, pressure, or relative humidity of the combustible gas mixture, multiple test environments were examined. At each ignition, a computer re-corded the temperature, pressure, and relative humidity of the gas immediately prior to the explosion. These data were then used to establish the effect of the test environment on the ignition probability and to create a mathematical model of the test environment's synergistic effects. The analysis indicated that these effects were not as significant as previously expected. No general algorithm was found that could be used to predict these effects across the range of circuits tested.

Jan 1, 2010

By Gavin Beer

The Chelopech Copper/Gold Mine, located in west-central Bulgaria, has been in operation since 1953 producing a low-grade copper/gold concentrate containing up to six percent arsenic by weight. The penalties and restrictions imposed on smelting this concentrate, have seen the past operators of the mine strive to find a balance between achieving acceptable metal returns from the smelters and installing novel or unproven technologies in the face of changing political and economic climates. This paper documents the colourful history of the concentrate processing alternatives that have been investigated and implemented over the 45 year life of the Chelopech Mine, culminating in the high pressure oxidation option that is now the focus of a Definitive Feasibility Study (DFS) presently being undertaken by GRD Minproc Limited. The fundamental chemistry of the preceding alternatives is outlined followed by a discussion as to why each was ultimately not employed. A detailed description of the technology proposed in the DFS is given including: pressure oxidation, arsenic fixation, SX/EW copper recovery, CIL gold recovery and AVR/SART cyanide/copper recovery processes. Keywords: Arsenic, Scorodite, HPOX, Chelopech, Dundee

Jan 1, 2005

By H. P. Greenwald, H. C. Howarth

There was reported in Bureau of Mines Technical Paper 5754/ a series of tests to determine the compressibility and bearing strength of specimens prepared from blocks of potash salt obtained from a mine near Carlsbad , N. Mex . The events leading up to the investigation were sketched in a foreword by George S. Rice , then chief mining engineer of the Bureau ( retired September 30 , 1937 ) ; this foreword also gives a discussion of the possibility of increasing the ultimate total recovery of the potash salt by " second mining" of pillars or by use of a longwall system . In June 1936 , Rice and the senior author visited Carlsbad with H. I. Smith , chief of the mining division of the Geological Survey , to observe mining then in progress and to discuss with the management of one of the mines records of convergence of roof and floor which they were obtaining . It developed that serious thought was being given to the possibility of roof failure resulting from shear at the faces of pillars . There was envisioned the danger of such cracks extending upward to water - bearing strata . Obviously , the simple compression tests of the potash salt then being made would throw no light on this question , and tests of assemblies of potash and roof salts would have to be made . In this connection it is to be remembered that in the mine no sharp division exists between the potash salt being recovered and the nearly pure halite which forms the roof . The interlocked crystalline structure is continuous , and there is merely a very rapid decrease in the proportion of sylvite in a short distance vertically . Figure 2 of Technical Paper 575 shows that two samples near the top of the salt being mined contained , respectively , 51 and 65 percent potassium chloride . Contrasted with this is an analysis of the roof salt given on page 24 of that publication , which showed only 3.6 percent potassium chloride . As the data given in Technical Paper 575 show , the roof salt is much less plastic than the potash salt . The immediate roof may then be thought of as a more rigid stratum of indefinite extent resting on and continuous with yielding supports and loaded uniformly at the rate of 900 to 950 pounds per square inch . Just what thickness of the salt should be considered as immediate roof is uncertain .

Feb 1, 1938

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

By A. Z. Lang, D. A. Hall

After a brief description of the causes of spontaneous heating and of general preventative methods, a detailed account is given of occurrences of spontaneous heating in the Main Seam (locally known as the 5/4 Seam) at Westoe Colliery. This seam is about 12 feet thick consisting of hands of coal and shale, but only 4 feet 6 inches is worked because of the thickness os strata in water-bearing rocks and the worked section is selected on quality considerations. An advancing longwall face in this seam (2nd South) began to heat after working for six months and ultimately had to be abandoned. By adopting retreating methods and mining narrow panels it has been possible to extract this coal at an excellent rate of productivity. The system of goaf ventilation is important, because the use of a bleed road would have given rise to dangerous conditions in a goaf which of necessity would have contained fallen coal. Preparatory seals were prepared at selected sites so that, if necessary, a panel could be sealed off quickly; these seals are completed as soon as possible (within three weeks) of finishing a panel. A gas sampling system has been instituted which includes daily sampling on the face and in the goaf, and weekly sampling at the stoppings of all completed panels. The coal has now been extracted from this seam for three years without any further difficulties from spontaneous heating.

May 23, 1905

By C E. Loo

The cohesive zone has a significant influence on blast furnace operation and performance. The high-temperature behaviour of the reducing ferrous burden determines the properties of the cohesive zone and is studied in a laboratory using a softening and melting test. This paper summarises recent work aimed at better understanding the physico-chemical changes in a ferrous bed during softening and melting. Using a combination of standard, non-standard and quenched tests supported by optical image analysis, this work has highlighted some important differences in behaviour between lump, pellets and sinter as well as between the two lump ores and two acid pellets. As with the two lump ores, one pellet is denser than the other and the denser ore/pellet is also higher in silica.Within the cohesive zone, densification of the ferrous layer leads to reduced permeability and greater pressure drop. From the work presented in this paper, two key mechanisms of ferrous layer densification were identified. Firstly, the formation of fayalite, which melts at low temperatures, can act as a lubricant between particles and lead to densification of the ferrous layer under load. Secondly, reduction to metallic iron is topochemical and fayalite in the outer shell of the particle restricts gas flow to the centre and results in the formation of a wustite core. As temperatures rise, the wustite melts and eventually exudes out of the shell, occupying void spaces between particles and further reducing layer voidage and permeability.This work has shown that density and silica content are two key factors that result in increased densification of the ferrous layer. For porous Australian lump ore, the higher porosity and lower silica reduces the formation of fayalite and limits the formation of the wustite core, ultimately leading to a more permeable bed. The difference between the porous and dense ores was more pronounced with the introduction of prereduction to better simulate blast furnace conditions. This suggests that a porous ore gives significantly better cohesive zone permeability and blast furnace operations than a dense ore.The behaviour of fluxed sinter particles is different in that the silica reacts with lime to form dicalcium silicate. Minimal wustite core forms because relict hematite particles in sinter are only small and reduction occurs uniformly throughout the particle. Even with significant loss of material through prereduction, beds formed from sinter remained comparatively rigid. Studies using a typical blast furnace burden mix of 80 per cent fluxed sinter and 20 per cent porous ore showed that the structures of these beds at softening and melting temperatures are very similar to the sinter-only test. Measurements of bed contraction and pressure drop also confirmed that the introduction of 20 per cent porous ore into a sinter bed did not alter its properties. This is an indication that 20 per cent ore can be easily accommodated by blast furnace burdens.CITATION:Loo, C E, 2015. Important acid ferrous burden properties in the cohesive zone of a blast furnace, in Proceedings Iron Ore 2015, pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By T Ireland, S Eratne, W Newns, P Spies

The approach to risk management during the procurement of major projects often has a significant outcome on the ultimate delivery of a project. The NZ$1.4 B Waterview Connection project is the largest and most complex project yet undertaken by the New Zealand Transport Agency (NZTA) and the procurement process for an alliance contract was refined to provide compliance with the International Tunnel Insurance Group (ITIG) Code of Practice for Risk Management of Tunnel Works (TCoP). The principle of shared risk within an alliance incentivises a common understanding of project risks prior to finalising the alliance agreement and therefore enables superior risk management through design, construction and beyond. Risk management practices need to be instigated well in advance of commercial phases, so that commercial competition does not lead to a significant elevation of project risk. In particular the practice of gaining commercial advantage by taking on a potentially unmanageable level of risk is one of the outcomes to be avoided by the TCoP.During the procurement phase the NZTA placed high value on design and construction mitigation measures proposed in order to address ground risks, as is appropriate for a major tunnel project. In order to achieve alignment on the level of geotechnical risks an Alliance Geotechnical Baseline Report (AGBR) process was developed.This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. Refinements to the procurement process to ensure compliance with the TCoP prepared by the International Tunnel Insurance Group (ITIG) are described along with the AGBR process applied as part of a suite of measures to achieve a successful procurement outcome.CITATION:Ireland, T, Spies, P, Eratne, S and Newns, W, 2014. Risk management and use of a geotechnical baseline report for a competitive alliance procurement?process, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 553–562 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014