Search Documents

By Mark Colwell

As per most other earth science engineering problems, the underground coal geotechnical environment and the way in which roof and rib support interacts with the rock mass are complex issues. While the problem should not be oversimplified (i.e., the dominant failure mechanisms or critical data input parameters should not be ignored), without question judicious simplification is at the heart of all good engineering design. Engineers play a vital role in supplying the world with solutions and products; however it is crucial that engineers make practical and readily useable contributions. One way to ensure this is to employ simplification in the engineering process.

By N. Ahern, D. B. Dreisinger, G. Van Weert

In the thiosulfate leaching of gold, degradation of the thiosulfate reagent is a major cost. One of the intermediary degradation products is trithionate, which also inhibits gold recovery from solution by ion exchange. Little attention has been given to this species in the context of gold leaching - the limited information on trithionate and its solution chemistry available in the literature is seldom directly related to gold leaching conditions. This review is a compilation of the published knowledge on trithionate, with a specific focus on identifying the relevance of this information to gold leaching and the shortcomings in the knowledge base.

Jan 1, 2005

By J. Robison, H. Pieterse, C. C. Smith, M. Luque, S. Chipman

Phase change during pressure let down releases significant amounts of energy that must be controlled to avoid undo wear and tear on equipment. Hydrometallurgical slurries require flow control equipment (valves and tanks) made of expensive materials to withstand the abrasive, and often corrosive nature of the slurry. Presented is a model of the nozzle of a let-down choke which is designed to control the flow pattern that exits the choke (valve) as it enters the receiving tank. This model can be used to design chokes which allow for the dissipation of the energy released during pressure let down by spreading the stream over a significant portion of the slurry pool in the receiving tank to minimize wear on equipment near the nozzle exit and the bottom of the slurry tank. An example uses the model to choose the nozzle expansion (area) ratio to select the outlet slurry velocity and slurry expansion angle.

Jan 1, 2004

By C. Ortuglio

The Bureau of Mines developed equations to determine the relationship of yields and products obtained from BM-AGA carbonization in 13-and l8-inch-diameter retorts. The developed equations indicate that results of carbonization in l8-inch-diameter retorts can be predicted from results obtained with l3-inch-diameter retorts.

Jan 1, 1966

By W J. Botha

The Palaeoproterozoic Transvaal Supergroup in the northern Cape Province of South Africa hosts high grade (>60 per cent Fe) hematitic and specularitic iron and manganese mineralisation. The mineralisation is primarily exposed along the western margin or in the central part of a major interference fold structure known as the Maremane dome. The bulk of South AfricaÆs iron ore production is currently provided by two active mines, Kumba Resources megaton Sishen iron ore mine on the northern end of the dome, and the smaller Assmang Beeshoek mine on the southern closure. The undeveloped Sishen South deposit, which contains ~400 Mt of high-grade hematite ore, is located approximately 9 km towards the southwest of Postmasburg. It forms a linear extension of the Beeshoek mine and as such contains comparable laminated, breccia and conglomeratic iron mineralisation. The Transvaal Supergroup sediments were deposited in two distinct fault-controlled basins on the Archean Kaapvaal craton. Basement rocks in the western Griqualand West basin are formed by a carbonate platform sequence (Campbellrand Subgroup), which is overlain by a thick sequence of banded iron formation of the Asbesheuwels Subgroup. A major unconformity separates these rocks from the red-bed Gamagara Formation, which is correlated with the base of the Olifantshoek Supergroup. Diamictites and lavas of the Postmasburg Group have been thrust over these units from the west. The mineralisation process is related to regional scale supergene iron enrichment of Kuruman banded iron formations along the unconformity. During regional tectonism associated with the Kheis orogeny (2400 - 1700 Ma) the Maremane dome was uplifted, and the basal dolomite units thus exposed to erosion and karstification. The overlying banded iron formations collapsed into karst sinkhole structures where leaching of silica and enrichment of hematite occurred. Although the exact mechanism of the mineralising process remains unclear, karstification preserved components of the original concordant laminated and massive ores. These ores were subsequently eroded and deposited as conglomeratic and gritty ores down-dip of the Maremane dome in alluvial fan systems. A thin veneer of recent calcrete or Tertiary Kalahari clay beds masks the subsurface geology and most of the orebodies, thus ground geophysical gravity surveys proved excellent exploration tools to penetrate the surficial cover. These surveys were used extensively for delineation drilling and to deduce the subsurface geology and structural development of the area. Finally Sishen South orebodies were modelled with ModelVision software in an attempt to obtain an exploration template for the surrounding area.

Jan 1, 2005

By Virgil L. Barr

National income originating compared to physical production for an enterprise or an industry reflects its ability to strengthen the national economy. For a single industrial sector or for an industry this comparison can be useful to reflect changes that may occur in this ability to contribute because of changing supply-demand-income-investment equilibria. A favorable relationship can be postulated by specified economic incentive, and the accompanying technologic input required can be shown. The new index proposes the use of the Federal Reserve Board indexes of production divided by the constant dollar income originating in the petroleum industry which reflects increases or decreases in performance. When compared with other mineral industries and with, total industry, an approximation of relative strength is evident. By constructing three different hypothetical conditions for future petroleum imports, assuming a constant excess capacity requirement for domestic production, and providing an estimate for future domestic demand for petroleum, the impact on the performance index can be shown. Thus, a strong position for the petroleum and natural gas industry can be stated. If this is done, it becomes evident that because of restrictions on cost-price relationships, a drilling program that would provide enough domestic oil to meet demand may not be practicable. By difference, the amount of improvement in methods of production and processing through technologic advancements can be stated explicitly.

Jan 1, 1960

By M. L. McAllister, M. Veiga

The mineral industry has seen many significant changes in the past decade. Increasingly, it has responded to unanticipated pressures and demands with a variety of voluntary initiatives. Yet there is still much to do. Mining now takes place in a different context than was the case in the past. Socio-economic, political and environmental considerations must now be integrated into traditional mining systems. This process of integration needs to involve industry, governments, academics, communities and other stakeholders to design a new approach to mining, one that can be fostered through interdisciplinary links and holistic strategies. This paper considers the meaning of sustainability in the context of the Canadian mining industry and explores the need for a broader vision for the mining industry. The role of technology is then analyzed and related to an initiative recently taken by Canadian universities to develop a national network for interdisciplinary research into sustainable mining, CaSM.

Jan 1, 1999

By L. R. Verney

A number of interrelated factors influence the economics of the sulphide smelting of copper, lead, zinc and nickel. This paper discusses these factors, mainly from a US point of view, and shows how they affect the cost of construction and operation of new and existing plants. The paper shows how metallurgical plant construction costs and the consumer price index have increased at a much faster rate than metal prices thereby making some metal mining and production operations within the USA, Canada and the EEC less profitable than operations elsewhere. This in turn inhibits new "grass roots" metallurgical developments. It is explained how retrofit of existing pyrometallurgical plants can be a more viable development than the construction of "green field" plants, especially if such retrofit improves, energy efficiencies, overall operating costs and reduces emissions of sulphur and other toxic wastes. Some aspects of metallurgical plant operation are examined, especially for copper and nickel, to show how changes in operating practices may develop in order to improve overall smelting economies, especially when developed in conjunction with objective retrofit. The paper also examines some financial aspects, especially insofar as the disparity between terms for loans offered to third world countries and the USA and the EEC are concerned and also comments upon the need, especially within the USA, for legislation to permit rapid depreciation of capital. Specific comments are made about environmental aspects, including the lack of uniformity of pollution control legislation and how environmental considerations may have some bearing of the location of future smelting operations.

Jan 1, 1983

By D. A. Livingstone

Abstract Golden Manitou Mines, Limited, nine miles east of the town of Val d'Or in northwestern Quebec, are presently milling, at the rate of 1,000 tons daily, a relatively complex 3.11-phide ore and producing, in decreasing order of value, zinc, silver, gold, lead, and copper. The products are a zinc concentrate, a silver-lead-copper concentrate, and a silver-gold precipitate from cyanidation. Although several independent pre-production metallurgical investigations into the treatment of the ore were carried out, current practice is different from any of the recommended methods and, while still leaving room for improvement, is considerably more effective than earlier performance. Flow-sheet developments from the commencement of operations in 1942 are dealt with briefly, showing the reasons for making numerous changes, the shortcomings of the various schemes tried, and, finally, covering data pertinent to present-day practice. From the recovery standpoint, silver has presented the greatest difficulty. The writer's association with the Company coincided with the start of production. Characteristics of the Ore The predominant metallic minerals present in the ore, in decreasing order of their abundance, are: pyrite, sphalerite, galena and chalcopyrite, with lesser amounts of argentiferous tennantite-tetrahedrite, arsenopyrite, covellite, bornite, and chalcocite. The sphalerite is mostly light in colour, sometimes colourless, and practically free from combined iron. Some of the sphalerite is very closely associated with minor amounts of pyrite, chalcopyrite, and galena. Pyrie is abundantly disseminated as medium to fine grains; more rarely it is massive and contains occasional grains of sphalerite, galena, and chalcopyrite.

Jan 1, 1952

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By Cecil H. Desch

THE progress of metallurgical practice and the demands made by the engineering industry on our foundries and mills have made the crystalline structure of metals a subject of far more than academic interest. Metals and alloys are made up of crystals. Even if we accept the view, so ably maintained by some metallurgists, that the crystals are separated from one another by an amorphous layer, it remains true that all but a very minute fraction of any metallic mass is crystalline. The conditions which affect the growth of crystals are therefore of importance in metallurgy. It is not only castings whose properties depend on the arrangement of their crystals, for the more we learn of the behavior of forged, rolled and drawn metals, the more certain it becomes that it is profoundly influenced by the size and arrangement of the crystals in the original ingot, deter- mining a structure which may persist in a modified form through a long series of mechanical operations and annealings. This is mainly due to the concentration of much of the impurities in the last portions of the liquid to freeze, so that the boundaries between single crystals or groups of crystals are marked out by a zone of segregated material, differing in properties from the mass, and offering a barrier to diffusion and equalization of composition throughout the whole. The importance of this fact has been fully recognized by steel manufacturers, who have to deal with ingots which are sometimes very large, and are cast at a high temperature, containing impurities which have a marked effect on the properties even when present in very small quantity. For this reason the Iron and Steel Institute has set up a committee to examine the whole question of the heterogeneity of steel ingots,(l)f and a report has been issued, containing an account of the structure of 16 ingots, ranging in weight from 15 cwt. to 172 tons, each of which was sectioned and examined by chemical analysis and by etching. A valuable body of data concerning segregation has thus been collected. The work of the committee is being prosecuted with great activity, and at the same time researches are in progress to determine the physical

Jan 1, 1927

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study of ten existing or proposed port sites in Alaska, the Bureau of Mines examined the potential for mineral development around three Alaska port sites: Iliamna Bay, Kotzebue, and Nome. The mineral deposits near Iliamna Bay include gold, copper, and iron. Development of minerals in this area will require the discovery of new deposits or the definition of additional are reserves at known deposits. The mineral deposits near Kotzebue are primarily gold, copper, coal, lead, and uranium. Based on the character of these deposits, it appears that development of a small-scale mine supplying coal for regional use is the most likely scenario in the near-term. The mineral deposits near Nome are primarily gold and copper. Development of small underground gold mines is possible, however it appears that expanded offshore gold dredging will have the greatest impact on the flow of freight and goods through the Nome port in the near term.

Jan 1, 2011

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

By S. C. Ellis

THE bituminous sand of northern Alberta has already an extensive literature, and most of the reports dealing with the subject are still available (see Selected Bibliography at end of paper). A phenomenon so striking and, as regards its extent, so unique, as the deposit in the vicinity of McMurray settlement could not fail to attract the notice of the early explorers, and we find references to it as far back as the latter part of the eighteenth century. However, scarcely a thought had been bestowed upon the possible economic value of minerals in the the remote northern parts of Canada before the second decade of the present century, and practically no detailed mapping had been done north of the town of Athabaska. The late Wm. Ogilvie made a track survey of Athabaska river in 1884, and surveys of certain lines-including the 23rd base line-had been completed by 1911. Between this base line and lake Athabaska, nothing had been attempted. Actually, no definite information at all was available regarding the character and extent of the bituminous sand when, in the earl y summer of 1913, a reconnaissance party set out from Athabaska for McMurray. At that period, the journey was made in summer by scow or canoe. No telegraph line had been laid, and a casual mail service by canoe or dog team once in three months formed the only means of communication with the outside world. The investigation has begun by the Mines Branch was continued during several subsequent years. The sand deposits were studied and sampled, the bi rumen was extracted from the sand and studied chemically and physically, and the economic significance of the deposit was given exhaustive study.

Jan 1, 1937

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By P. L. Woolf

Seven evaluation tests with blast furnace iron bearing burden materials are described. The effects of pellet strength, fines in the burden, decreasing slag volume, pellet size, eliminating stone with superfluxed sinter, and eliminating stone by prefluxing the pellets were determined. Fluxed pellets and fluxed sinter made with the same ore fines were compared. The tests were conducted under cooperative agreements between the Bureau of Mines and North American steel companies. The objectives were to improve blast furnace practice, expand and develop understanding of the operation and theory, quantify the effects of changes, and explore the limitations of operability. This work was part of an extensive program of blast furnace research in experimental blast furnaces at Bruceton, PA conducted in the years 1958 to 1967.

Jan 1, 1984

By Mike de Wit

Of the approximately 6,500 kimberlites known to date, less than 3% are diamondiferous and less than half of those are economically viable. Admittedly, this is a global figure and varies from area to area much depending on geological, logistical, and political circumstances. The number of diamond-bearing kimberlites is an important geobarometer, and an age-frequency profile has been compiled in order to identify diamond metallogenic epochs and provinces. Four primary diamond clusters have been recognized: Siberia (332-370Ma), Kaapvaal South(114-144Ma), Kaapvaal Southwest(84-95Ma), and Slave (52-55Ma). In addition, three secondary clusters are the Kaapvaal Central (S06-S38Ma), the Man Craton (139-lS3Ma) and the Kasai Craton (120-130Ma). The Kaapvaal is the only area where kimberlites with diamonds were discovered between 1870 and 1925, except for the Prairie Creek discovery in North America in 1906 and Colossus in Zimbabwe in 1907. Between 1906 and 1940 no major diamondiferous kimberlites were discovered, but many of Africa's alluvial deposits were found and exploited in that period. Advances in scientific prospecting in the 1940's rapidly accelerated the discovery rate that peaked in the 1990's; 39 diamondiferous occurrences were found in the 1980's, of which 8 became mines and 5 are in feasibility, and nearly 450ha of kimberlite was added to the global resource base. Despite the accelerated exploration expenditure, the last decade (e.g. 2000-2009) has been the leanest since the 1940's. The most important reason for this decline in exploration success is that any undiscovered deposits are largely buried by younger cover. Understanding complex and geophysical noisy basement geology, as well as decomposition of path-finder minerals are major challenges to further exploration success. Major investments in basic geological expertise and field research will have to be made in order to secure future diamond resources. Integrated geophysical studies, geochemistry diamond forensics, and improved imaging of Earth's upper mantle are perhaps foremost in this requirement, but the costs of these activities are such that government support will be required if countries are to sustain their diamond mining industry.

Jan 1, 2010

By Robert A. Laurence

Ore deposits in the Southern Appalachians are ( 1) sedimentary or syngenetic, ( 2) epigenetic, and ( 3) residual. In general, deposits characteristic of high temperature and pressure are found in the Blue Ridge and Piedmont provinces and those of low and intermediate temperature and pressure, including the sedimentary ores, are found in the Valley and Ridge and Appalachian Plateaus provinces. Residual deposits are present throughout the area. Recognition of several periods of intrusion and metamorphism in the Appalachians has changed former concepts which held that most mineralization was of late Paleozoic age in a zonal pattern including all four provinces. Many deposits probably are of early or midPaleozoic age. Similarly, recent studies in geomorphology indicate that the formation of residual deposits is a continuous process and not related to specific cycles of peneplanation.

Jan 1, 1968

By A G. Grice

WMC Resources Pty Ltd û Copper Uranium Division operates the large underground Olympic Dam Mine at Roxby Downs, South Australia. These operations mine and process the ore to produce refined copper, uranium oxide, gold and silver. In mid-1996, the company committed to the Olympic Dam Expansion Project (OEP) to expand production from 3.0 million tonnes per annum of ore (85 000 tonnes per annum of copper metal) to over 9.0 million tonnes per annum of ore (over 200 000 tonnes per annum of copper metal). Along with the increase in the ore production capacity of the underground mine and the surface ore handling and processing facilities, expansion of the backfill system was required. The target backfill placement rate was 2.0 million cubic metres of backfill per annum which was to be predominantly delivered as cemented aggregate fill (CAF). This paper discusses the engineering activities undertaken to assess and change the method of designing the required strength of fill exposures. In addition, the operational changes that were introduced to achieve the required fill quantities and the mix designs to meet the specified strengths, including the use of alternate binders, are discussed. This work resulted in a large increase in the fill placement rate and a reduction in the overall unit cost of fill.

Jan 1, 2000

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.