Search Documents

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

Sampling errors result from heterogeneities within the lot under study. Within a rock mass in situ heterogeneity results in the geological nugget effect, which accounts for most of the natural variability. In broken rock, constitution and distribution heterogeneities are important. A major result of the constitution heterogeneity is the Fundamental Sampling Error (FSE) which is the smallest residual error that can be achieved. It cannot be eliminated, but can be minimised and refl ects the fact that the broken rock sampling process is never completely free of error. Together with other sampling errors, FSE contributes to the total nugget effect. The FSE for a sampling protocol can be evaluated using the so-called Gy equation. Its practical applications to low-grade gold ores have often been unsuccessful due to problems linking the FSE and minimum sampling mass and the defi nition of key parameters such as the liberation diameter. Well-designed sample protocols minimise the total sampling error and hence the nugget effect. Reduction of the nugget effect is a key requirement for all sampling programs whether related to exploration and resource evaluation, metallurgical test sampling, grade control or metallurgical plant sampling. This contribution reviews the relationship between heterogeneity, FSE and nugget effect in gold deposits; and emphasises the need for FSE management throughout the mine value chain.

Aug 1, 2010

By Carl R. Peterson

Development of reliable, portable, low headroom, hard rock crushers would improve the efficiency of most currently operated conveyor systems and make it possible to bring conveyor haulage closer to the face, thus eliminating expensive rock rehandling procedures. A crusher that could be easily moved would permit the more widespread use of lower cost haulage systems, such as conveyors, to transport the ore out of the mine. Such crushers would be installed close to the working areas, resulting in an optium haul from the face to the dump location. A recent contract study by Rapidex, Inc., "Application Study of Portable Underground Hard Pock Crusher" (USBM Contract No. J0265006) provides a survey of industry needs in portable underground crushing, together with conclusions and concepts as to specifications and type of crusher required to serve the greatest number of operations. To fill this need a three phase program has been undertaken by the Bureau of Mines: Phase I - Design: Phase II - Construction and Testing, and Phase III - Production Underground Test. This report covers Phase I only, and includes the complete engineering design and specifications of the Rapidex Rotary Jaw Crusher conceived in the earlier "Applications Study". Also included are the design, construction, and testing of a quarter-scale functional model, utilizing three different types of rock and two different crusher feeder systems.

Jan 1, 1978

By J. M. Newell, G. R. Peatfield

"The Red-Chris porphyry Cu-Au deposit is located between Ealue and Kluea lakes, southeast of the village of Iskut on the Stewart Cassiar highway in northwestern British Columbia. It was explored by Texasgulf Inc., in a joint venture with Great Plains Development Company of Canada, Ltd. and Silver Standard Mines Ltd., during the period 1973 to 1980. Exploration resumed in 1994, following acquisition of the interests originally held by Texasgulf and Great Plains Development by American Bullion Minerals Ltd.Prospectors were first drawn to the area by prominent limonitic stain zones exposed in creek gullies in the western part of the property. These zones are developed on the alteration halo at the western periphery of the deposit. The potential ore zones do not crop out and were first exposed in a bulldozer trench excavated in 1971. Subsequent exploration was by percussion and diamond drilling, guided to some extent by induced polarization surveys. In 1976, estimated resources contained within two crudely designed open pits were 41 million tonnes with an average grade of 0.56% Cu and 0.34 g/t Au, with a cutoff grade of0.25% Cu. New resource estimates based on a major drilling program completed by American Bullion in 1994 were released as this paper goes to press. These estimates were calculated using various copper cutoff grades; at the 0.4% Cu cutoff, the ""in-situ geological reserve"" is given as 100 million tonnes grading 0.58% Cu and 0.46 g! t Au (American Bullion Minerals Ltd., 1995).The deposit consists mainly of pyrite, chalcopyrite and increasing bornite at depth, in zones of quartz-vein stockwork hosted by an elongate body of altered monzonite porphyry of latest Triassic or earliest Jurassic age. The stock intruded volcanic and sedimentary rocks of probable Stuhini Group affinity and is in faulted contact with sedimentary rocks of the Jurassic Bowser Lake Group. Gypsum stockworks are developed in the higher levels of the subvolcanic porphyry system. Late-stage quartz-carbonate veins carry small amounts of galena and sphalerite. Complex faulting within the deposit makes drill-hole correlations difficult. Alteration assemblages include an early potassic phase, almost completely destroyed by later phyllic alteration, and surrounded by a propylitic assemblage dominated by ankeritic carbonates in altered sedimentary rocks.The deposit has characteristics of bath the alkalic and calc-alkalic classes of porphyry copper deposits. The development of quartzvein stockwork suggests a calc-alkalic affinity, but the hostrocks contain little or no free quartz, molybdenum is present in trace amounts only and gold values are significant. Copper grades vary between wide extremes with unusually high grades in some sections of the deposit. The weight of evidence available in the 1970s led us to place the Red-Chris deposit firmly in the alkalic family. The quartz-sericite alteration assemblage was attributed to breakdown of potassium feldspar in a near-surface alteration environment in which seawater may have had a significant role. These interpretalions are retained here, but preliminary conclusions from the most recent work suggest that they may require some modification."

Jan 1, 1995

By V. E. Edlund

Pyrometallurgical studies by the Bureau of Mines demonstrated the feasibllity of sintering and smelting a low-grade flotation concentrate made by pilot-plant processing 10-percent manganese ore from the Maggie Canyon deposit, Mohave County, Ariz. Under optimum conditions 85 percent of the manganese in a flotation concentrate that assayed 36 percent manganese was recovered as standard ferromanganese. A blend of this flotation concentrate with high-grade dithionate pilot plant precipitate was similarly processed with a recovery of 90 percent of the manganese. Thorough mixing and pelletizing of the charge before treatment on the sinter hearth was necessary to produce a well agglomerated product by single pass sintering. Although satisfactory sinter was produced from a variety of material combinations, best results were obtained on a charge that contained 80 percent flotation concentrate and 20 percent return sinter fines. This combination was mixed with 6 percent coke, based on weight of concentrate; and 12 percent moisture. Sintering such a charge yielded a well agglomerated product containing over 80 percent coarse material, The results of standard crushing tests showed that the product was physically comparable to iron ore sinters and manganese nodules.

Jan 1, 1962

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps,

Jan 1, 1964

By G. Popplewel

Commencing with the Pre-Feasibility Study (PFS) conclusions, the Orapa 3 process design evolved through a phase of value-engineering studies. An overall re-evaluation of the originally proposed process design was necessary both in order to address the interim increase in target throughput from 9.8 Mtpa to 12 Mtpa as well as to increase capital efficiency. In the interests of clarity, the PFS process design for Orapa 3 has been omitted from this paper, as it is no longer relevant. Recognition is however due to those engaged in earlier phases of the Orapa 3 project with respect to fundamental mass-balancing modelling; and ore and diamond characterization, which fanned the basis for the process design that has evolved from feasibility study activities.

Jan 1, 2010

By D. A. Larson

The Bureau of Mines conducted basic experiments to study the process of crack propagation with a wedge indenter. The work was conducted under plane stress conditions in a hard, brittle limestone. The purpose of these experiments was to first gain an understanding of the basic crack propagation process under a sharp indenter, and second, to determine how the crack propagation process could be used to improve mechanical fragmentation systems. Three methods of rock fracture with the wedge indenter were investigated in this program. These were the confined indentation tests, the unconfined splitting tests, and the edge chipping tests. The confined indention tests represent worst case conditions for crack growth and formed the lower bound on fracture efficiency. The unconfined splitting tests represented best case conditions and fixed the upper bound of fracture efficiency. The edge chipping tests represented an idealized fragmentation process based exclusively upon the highly efficient fracture propagation process. Edge chipping achieved a specific energy of 25 in lb f/in3 compared to conventional drag cutters, which required a specific energy of at least 2,385 in·lb f/in3? Thus edge chipping is up to 100 times more efficient than conventional drag cutting. Because of these promising results, more work is planned with the fracture propagation process in three dimensions.

Jan 1, 1987

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By Max J. Spendlove

This Bureau of Mines publication reviews current recycling trends in the United States. Although near-term prospects are poor for recycling most present wastes, urban refuse is an important exception. Such wastes comprise a mine above ground, and much less processing energy is normally required to recycle the constituents of urban ore than to obtain them in equal amounts from natural raw materials.

Jan 1, 1976

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By J K. Claflin, S R. La Brooy, A M. Claflin

Rotary kilns have been in service in the gold industry to regenerate carbon for 65 years. At the time oxide ores with gold head grades of 8 to 10 g/t were being treated. Carbon could be regenerated adequately at 650°C and solution losses were less than 1%. Forty years ago, research indicated that heavily fouled carbon from flotation circuits had to be held at 750 to 850°C for ten to twenty minutes for full reactivation (Avraamides and La Brooy, 1987), gold head grades were typically 5 g/t and solution losses typically 0.02 ppm – still less than 1%. In 2017 it was determined (Claflin et al., 2017) that a residence time of less than 1 minute at 750°C can be adequate to reactivate carbon fouled with organics sufficiently to achieve 0.005 ppm solution losses in a flotation tailings leach plant.With the potential for discovery head grades to drop below 0.6 g/t, solution losses of 0.02 ppm represent over 3% loss. Tight operation of the whole carbon circuit is required to keep gold solution losses below 1% going forward.There are alternatives to a rotary carbon kiln, e.g. vertical kilns of which the Minfurn, Rintoul and Combustion Air kilns are examples. The alternative kilns can be heated using electrical heating elements, induction, and microwave. These kilns can operate successfully under the right conditions, however, they are almost exclusively for small carbon throughputs and are not suitable for the large carbon advance rates that are required to process low head grade ore deposits. Large throughput carbon kilns are are almost exclusively fossil fuel fired rotary kilns and the subject of this paper. In the view of the principal author, a fossil fuel fired vertical carbon kiln is preferred to a rotary kiln, however, it is not currently used in the industry.Thermal regeneration of activated carbon has a major impact on gold recovery in the carbon circuit. The carbon kiln and associated equipment constitute 3 to 5% of the capital cost for an oxide processing plant and up to 10% of the capital cost if flotation tails are leached. Despite the capital cost and impact on recovery, the carbon kiln is often poorly selected, operated and maintained.Six years ago Ausenco embarked on the Carbon Kiln Initiative to reduce solution gold losses. This body of knowledge has been published in a series of papers culminating in this paper on how to:1. Select a kiln appropriate for the flowsheet;2. Maintain the kiln to achieve design operation; and3. Operate the kiln to minimise costs and maximise reactivation.CITATION:Claflin, J K, La Brooy, S R and Claflin, A M, 2018. Carbon kiln selection, operation and maintenance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 251–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G. W. Birge, D. E. Wolfson, J. H. Lynch

This report presents all available 900 ° C BM- AGA carbonization and related data for coals from the principal beds of the southwest Virginia field in a form which permits ready comparison of product yields and properties of coals and cokes . Thirty- one channel samples from Buchanan , Dickenson , Russell , Tazewell , and Wise Counties were carbonized at 900 ° C in an 18 - inch - diameter retort . Blending properties of 10 of the coals were studied , and expansion of most of the coals and blends was measured in the Bureau of Mines sole - heated oven . Ash Most of the samples were chemically suitable for metallurgical use in coking blends , and their coking properties generally were satisfactory . content exceeded 10 percent in only three samples , and none of the coals contained more than 1.5 percent sulfur . Dry , mineral - matter - free fixed - carbon content of the coals ranged from 62.1 to 77.5 percent . Expansion behavior varied widely , ranging from 16.8 percent expansion to 27.6 percent contraction .

Jan 1, 1964

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By Michael Samis

The real option valuation method is often presented as an alternative to the conventional discounted cash flow (DCF) approach because it is able to recognize additional project value due to the presence of management flexibility. However, these two valuation methods can be separated on a more fundamental level by their differences in risk discounting. Real option valuation applies the risk-adjustment to the source of uncertainty in the cash flow while the DCF method adjusts for risk at the aggregate level of net cash flow. This seemingly small difference is the reason why the real option method is able to differentiate between projects according to each project?s unique risk characteristics while the conventional DCF approach cannot. This paper provides an overview of the real options and DCF valuation frameworks and discusses the differences in risk discounting that exist between the two methods. Using grade-school mathematics, this paper clearly demonstrates how, with real options, a unique project risk discount can be calculated which is directly linked to the project?s unique risk profile. It also highlights why the DCF method fails in this regard and shows why a call to ?increase the Risk-Adjusted Discount Rate? is an incomplete solution at best. Finally, a heap-leach project and satellite reserve development project are valued with both techniques and the difference in investment conclusions is explained in terms of the risk-discounting concepts discussed here.

May 1, 2003

By T. R. Curr, W. A. Gericke, J. Basson

South Africa is a leading player in the international ferro alloys industry. Historical factors that have contributed to this dominant position include an abundance of natural resources and relatively low cost electricity. A number of relatively recent developments are potentially threatening this position. These include new legislation affecting the mining and minerals industry, a shortage of some types of suitable reductants, depletion of surplus electricity generation capacity with resultant threat of real escalation of electricity prices and pressure resulting from the recent strengthening of the South African Rand. The industry is addressing these challenges in a number of ways to ensure long-term viability. Some of these measures include investments in more efficient technologies that have economy of scale benefits and are less dependent on expensive reductants and electricity. Local macro-economic impacts include new legislation regarding ownership of enter-prises, mineral rights and royalties on mineral sales, development plans for port and rail infrastructure, as well as initiatives to expand electricity generation and coke production capacity. The fundamentals for being a successful ferro alloy producer are still largely in place for South African producers. Therefore the South African ferro alloy industry will remain competitive and is well placed for continued growth in line with the international growth in ferro alloy demand. The industry should emerge leaner, more efficient and ready to respond to any future demands of the industry. This paper will cover the present status of the industry, the factors that are impacting thereon and a view on its future outlook.

Jan 1, 2007

By W. F. M. GOSS

The locomotives in service on the railroads of this country consume more than one-fifth of the total coal production of the United States. The amount is so large that any small saving that can be made effective in locomotive practice at once becomes an important factor in conserving the fuel supply of the nation. For this reason the United States Geological Survey gave attEmtion to the special problems of combustion in locomotive boilers. It approached this task from several different directions. The facts presented herewith constitute one series of results. In the fall of 1906 the locomotive-testing laboratory of Purdue University, at Lafayette, Ind., entered on a series of tests, one purpose of which was to determine in precise terms the degree of efficiency with which a modern high-class American locomotive utilizes the heat energy of the fuel supplied to it. The general interest in the subject, the elaborate plans which had been formulated for conducting the work, and the substantial character of the support which had been pledged to maintain it justified the Geological Survey in aiding the investigation. a The cooperation of the Survey consisted in detailing experts to assist the regular staff of the laboratory in the chemical and calorific work of the tests. These experts, working under the general supervision of the director of the Purdue laboratory, became responsible for the sampling of smoke-box gases, of the fuel used, of the cinders caught in the front end, of the sparks discharged by the stack, and of the refuse caught in the ash pan. The gas analyses were made by them at the university laboratory. The analyses of all solid samples and the calorific tests of the fuels were made at the government fuel-testing plant at St. Louis. The representatives of the Survey were not concerned with other phases of the work.

Jan 1, 1911

By B. Law, M. Menabde, B. Baird

Blasor is a new mine planning tool which is being used in the long and medium-term optimization of multi-open-pit operations throughout BHP Billiton’s Base Metals and bulk commodities portfolio. It is not just a scheduler, nor even only a schedule optimizer—although this function lies at the heart of the tool’s functionality—but a pit development plan optimizer, used from ultimate pit design and process plant capacity sizing right through to mining phase design and optimal panel scheduling. The tool uses a mixed-integer-linear-programming optimization engine to determine when material should be excavated and where it should be sent to optimize discounted operating cash flow over the life of operation. The core software design concept of Blasor is to provide a tool which is intuitive and flexible enough so that a competent mine planner can perform a pit development plan optimization without assistance from optimization specialists. To this end, a generalized graphical user interface has been implemented which allows full configuration of the optimization problem, including the definition of all inputs and constraints, specification of the material flow topology, bin and destination class definitions and full specification of the economic model encompassing prices and costs. This paper describes the capability of Blasor and outlines the design concepts underlying its design philosophy.

Jan 1, 2007

By A. K. Singh, R. Singh, P. K. Mandal

On the basis of in situ study of pillar loading at different sites, an attempt is made in this paper to visualize the development of mining induced stress under varying geo-mining conditions. Field study demonstrated interesting interaction between size of pillar and nature of roof rock mass under the influence of increasing dimension of the excavation. Stiffness of pillars/overburden, extraction ratio and depth cover are observed to be the important parameters for the estimation of mining induced stress over the pillar. These parameters influence, both, the value of ultimate induced stress (vertical) and its range of influence ahead of the face line. Further, it is observed that the change in width/height (w/h) ratio of a pillar has got considerable influence over the nature of mining induced stress over it. Impact of highly dynamic nature of mining induced stress over the natural supports is observed to be the most serious factor for the safety of working under a hard and massive roof rock mass. On the basis of these observations, a conceptual model of interaction between the natural support and overlying strata is discussed in the paper. ZUSAMMENFASSUNG: Aufgrund ist in situ Studium von Säule Beladung an verschiedenen Stellen, ein Versuch in diesem Papier gemacht, die Entwicklung des Bergbaus vostellen sich, Spannung unter Änderung von Geo Bergbau von Bedingungen hat veranlaßt. Feld Studium hat interessante Wechselwirkung zwischen Größe von Säule und Natur von Dach Felsen Masse unter dem Einfluß von Vermehrung Dimension des excavation vorgeführt. Steifheit des Säulen Overburden, Herausziehung Verhältnisses und Tiefe sind beobachtet bedeckt, die wichtigen Parameter für die Schätzung des Bergbaus zu sein, Spannung über der Säule hat veranlaßt. Diese Parameter beeinflussen, beide, der Wert allerletzter veranlaßter Spannung (senkrecht) und sein Bereich des Einflusses voraus von der Gesicht Linie. Weiter ist, es beobachtet, daß die Änderung in Breite Höhe (W H) Verhältnis einer Säule beträchtlichen Einfluß über der Natur des Bergbaus erhalten hat, Spannung hat darüber veranlaßt. Schlag sehr dynamischer Natur des Bergbaus ist Spannung über den natürlichen Stützen beobachtet hat veranlaßt, der ernsteste Faktor für die Sicherheit des Arbeitens unter einer harten und massiven Dach Felsen Masse zu sein. Aufgrund dieser Beobachtungen, ein begriffliches Modell der Wechselwirkung zwischen der natürlichen Stütze und der überlagernde strata ist im Papier diskutiert. RESUME: En se basant sur dans l'étude de situ de chargement de pilier aux sites différents, une tentative est faite dans ce papier pour envisager le développement de creuse la tension persuadée sous varier de conditions de geo creuse. L'étude de champs a démontré l'interaction intéressante entre la taille de pilier et la nature de masse de rocher de toit sous l'influence d'augmenter de dimension de l'excavation. La raideur de piliers overburden, la proportion d'extraction et la couverture de profondeur est observée pour être les paramètres importants pour le jugement de creuse la tension persuadée par-dessus le pilier. Ces paramètres influencent, les deux, la valeur de tension persuadée ultime (vertical) et sa gamme d'influence en avant de la ligne de face. Plus, il est observé que le changement dans la largeur hauteur (le w h) la proportion d'un pilier a reçu l'influence considérable par-dessus la nature de creuse la tension persuadée par-dessus il. L'impact de nature extrêmement dynamique de creuse la tension persuadée par-dessus les soutiens naturels est observé pour être le facteur le plus sérieux pour la sûreté de fonctionnement sous une masse de rocher de toit dure et massive. En se basant sur ces observations, un modèle conceptuel d'interaction entre le soutien naturel et les couches recouvrant est discuté dans le papier.

Jan 1, 2003