Search Documents

By G. W. Groove, E. E. Quenon

"INTRODUCTION Uncontrolled mine fires originating in exposed coal beds through the acts of careless or irresponsible persons present a serious threat to buildings, surface property, and the life and health of persons near the affected area. Apparently, the seriousness of such fires is not fully understood by property owners or those residing in the vicinity, as practically nothing has been done to alleviate conditions. In many instances, such fires have been active for several years before property owners or civic organizations have shown any interest toward having the fire extinguished. Recommendations by Bureau of Mines investigators in the interest of controlling such fires are seldom followed, as the Bureau cannot provide the funds for doing the work.Several uncontrolled and widespread fires are burning along the outcrop of coal beds and in underground abandoned mine workings within a 25-mile radius of Pittsburgh, Allegheny County, Pa. If these fires are permitted to continue to burn unabated, the ultimate results may be far-reaching. Most of the outcrop fires investigated are believed to have originated from burning rubbish, forest fires, or workmen, hunters, or others building fires near the outcrop of ,the coal beds. In other instances, smoke and fumes have suddenly appeared in the vicinity of abandoned coal-mine openings, indicating that a fire has either burned its way along the outcrop of the coal bed or has traveled through the abandoned mine from another location. An underground or outcrop coal-mine fire will be very likely to continue to burn as long as an oxygen supply is present.; and, so far as is known, such fires do not stop burning automatically until virtually all combustible matter is consumed."

Feb 1, 1948

By K Williams

Marvel Loch South Pit has had a number of stages of open and underground mining activities before acquisition by Sons of Gwalia. The historical pit had achieved a completed pit depth of 150 metres and the shaft and decline mine had reached approximately 220 metres in depth using open stope mining methods. The various mining methods reflect the various economics and industry practice at the time. The South Pit ore zones are medium grade (~2.5 g/t) but have a regular geometry and large tonnes per vertical metre. A number of studies have been completed up to a pre-feasibility stage looking at options to extend the pit depth and to lower the unit cost of gold production. The options considered were the re-optimisation of the pit to determine further cutbacks or the innovative use of an in-the-wall ramp. The in-the-wall ramp (tunnel) would permit the removal of the in pit ramp to expose additional ore that was within the footprint of the ramp design and to provide the opportunity to increase the final pit depth. Similar mining method has only been used at Three Mile (Coolgardie, WA) and Chalice Mine (Norseman, WA). The tunnel would serve as a gateway for further extension of the south mine and the central ore zone via underground mining methods. The ultimate depth of the South Pit has been extended to 310 metres below surface and significant additional ore has been recovered. This paper will give an insight into the various studies to optimise the Tunnel mining method, the determination of the various tunnel dimensions, and the phases of mining to arrive at the completed design.

Jan 1, 2003

By Martha McJunkin, Lawrence Pietrzak

This paper describes and demonstrates the application of systems analysis and mathematical modeling techniques in the planning of actual tunnel projects and research and development to improve tunneling techniques. A recently completed tunnel project located in Utah is used as an example. Although cost estimating computer programs are used in tunnel project planning, the introduction of performance modeling, simulating the time to excavate, has added advantages that are explored here. The performance/cost tunneling model (TM) described herein mathematically simulates on a high-speed digital computer the important activities of a number of tunneling techniques accounting for activity interactions, variable external environments, mechanical failure, and other uncertainties. A cost accounting segment is included to facilitate cost-effectiveness comparisons. It is shown that, when combined with informed judgment and appreciation of limitations, the TM can be a useful tool that may help improve tunneling operations and cost estimation, for example, by achieving more balanced system designs or bounding the performance/cost implications of geologic and other uncertainties. Ultimately, this might lead to more competitive bids and greater profits. The need for systems analysis and modeling in tunneling research and development (R&D) is well recognized and documented.(1-5) In R&D one must seek broadly useful solutions to the basic problems of face fragmentation, materials handling, ground support, and environmental control. These solutions must take account of the interdependence of these elements and, for a variety of ground conditions, the limitations or constraints that any innovation in one element may impose on total system performance and cost. In this regard the structure and logic of the TM has been kept as simple and modular as possible so

Jan 1, 1974

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991

By W. Rostoker, H. Nichols

The embrittlement by mercury of aluminum alloys in various states of anneal, cold work, and aging has been studied. It is shown that single phase and non-precipitation hardened structures irrespective of de,pee of prior cold work demonstrate some small measure of yielding before fracture occurs. Sub-yield-stress failure is confined to the aged state, and embrittlement is accentuated by small plastic prestrains. With large plastic pyestrains, embrittle~nent is progressively reduced. In previous work' it was shown that the propensity of commercial aluminum alloys for embrittlement when wetted with mercury seems to be related primarily to the intrinsic strength in the normal un-wetted condition. The data from a large number of commercial alloys in various states of anneal, cold work, and/or aging gave a generalized relationship. At low strength levels, the wetted fracture strength increases proportionately to the increase in tensile strength; but above 65,000 psi normal ultimate strength, the trend is abruptly reversed, and the wetted fracture stress decreases proportionately to the increase in tensile strength. This paper will demonstrate that the simple character of this relationship between normal tensile strength and wetted fracture strength is fortuitous. It will be shown that structure and thermal-mechanical history are clearly relevant factors. The term brittle fracture has been used to connote the geometry of the fracture surface (transverse vs shear plane) or the negligible extent of preceding plastic strain. At its maximum effectiveness, liquid metal embrittlement can satisfy both criteria—fracture transverse to the axis of tension and without observable plastic strain. In this paper, brittle fracture will signify failure at stresses below the engi-

Jan 1, 1962

THERE is available a considerable amount of literature concerning the practice, and, to a smaller extent, the theory of ventilation as it applies to coal mines. Publications considering the subject of ventilation of metal mines from a practical viewpoint are much less numerous, whilst the treatment of the theoretical aspect of the question (except in so far as is common to coal mining) appears to have been almost neglected. This may be due to one of two causes (a) That in many metal mines (especially those which have not attained a great depth), on account of the greater number of connections with the surface, as compared with coal mines, natural ventilation has sufficed.(b) That in metal mines where the foregoing is not the case the solution of the ventilation problem from theoretical considerations has been regarded as involving so many complications that any attempt at the determination of a set of concrete ventilation figures applying to and throughout the mine would be futile. Whilst it is freely admitted that the difficulties inherent in the application of theory to the ventilation of metal mines are numerous, it must also be admitted that few attempts have been made to overcome them. The ultimate aim, of course, would be the collection of sufficient data to enable the probable behaviour of the air-currents throughout the whole of the workings of any mine to be accurately predicted under any particular set of circumstances. Failing the attainment of this goal of perfection, it would at least appear that much valuable information might be obtained. In ventilation, as in...

Jan 1, 1921

By Gregory Comstock

THERE is a growing interest in the possibilities presented by the manipulation of metal powders, which justifies an attempt to summarize their character and potential value. A summary of this kind presents an opportunity for making a classification of metal powder products into several general types. Our present knowledge of the finer and more abstract aspects of many of the principles involved in metal powder technique is extremely limited. Any conclusions as to the ultimate value of the process will, therefore, for the present at least, be of doubtful value unless they are substantiated by its products. The number of such products is increas-ing. A study of their diverse and unusual characteristics; an examination of the methods by which they ale made, and a consideration of the reactions that take place during their fabrication, in so far as we can define them, should afford as good an evaluation of this interesting development as it is possible to make at this time. A critical study of this kind results in a formidable list of special attributes, which apparently are characteristic of applied powder metal-lurgy. A comparison of these special effects with the end products and well defined limitations of the melting and casting process indicate that often they may very well be considered as being special advantages. They are subject, of course, to certain not as yet so well defined limita-tions of their own. Based on current products only, a necessarily con-densed summary of the more striking special attributes of the metal powder process follows.

Jan 1, 1938

By John O. Marsden

Technology development has played a crucial role in the minerals industry throughout history. The development of new technology allows mankind to produce metals and minerals at progressively lower cost of production in real terms, and therefore at progressively lower prices, improving their availability, accessibility and utilization worldwide. However, the developers of such technology are not guaranteed to reap the benefits from this effort: There is an expectation that technology developers will gain an advantage over their competitors. Is this a short-term benefit that results from a temporary cost or efficiency improvement, or is it a sustainable longer term "edge" that prevails even after metal or mineral price has been eroded by the implementation of a major step change technology? This issue is examined by reference to several case study examples in the copper industry. BACKGROUND The development and adoption of new technology has played a crucial role in the commodity minerals industry throughout history. As new, cost-efficient technologies are commercialized, the cost of production decreases, and this enables lower grade ore to be processed profitably. This in turn increases the availability and supply of the metal or mineral of interest, and ultimately (in a free market environment where the supply- demand balance determines price) inevitably decreases the metal or mineral price. This leads to the question: Why should mining companies invest in (new) technology development if the result is a decrease in the product price? The answer is to achieve competitive advantage, where the application of new technology enables one or more

Jan 1, 2004

By Michael J. Sapko, Samuel P. Harteis, Eric S. Weiss

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL’s Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal’s ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

By Jon T. Langstaff

The microseismic method of detecting instability and high-stress zones in underground mines was first developed in this country by the US Bureau of Mines in the early 1940's (Obert and Duvall, 1957). Early laboratory experiments showed that when competent rocks are stressed in a testing machine, the rock noise rate (number of rock noises per unit time) increases with increasing applied stress. This increase is more pronounced as the ultimate strength of the rock is approached. Subsequent testing of rock noises in underground mines confirmed this laboratory experience and much effort has been directed in recent years to make use of this property to develop a practical method of predicting rock failure. Investigations conducted in the Coeur d'Alene district mines have pointed out a definite relationship between the stress buildup in a rock mass caused by mining activity and the emission of audible and subaudible seismic activity (microseisms). In 1968, a concentrated joint effort by USBM Denver Mining Research Center and American Smelting and Refining Co. at Asarco's Galena mine was undertaken to verify several theories regarding the generation of microseisms (Blake, 1971; Blake, Leighton, and Duvall, 1974; and Kovacs, 1973). Findings indicate that (1) rocks under stress emit detectable seismic energy; (2) the energy source can be located using a triangulation method involving travel time differences to various receiving stations; (3) the rate of release of seismic energy increases with increasing stress; and (4) this increase in noise generally precedes a major rock failure (rock burst).

Jan 1, 1979

Manganese ore has been mined from the Peak Hill Gold- field since 1948 and from the Pi'lbaraòGoldfield since 1954, and it is probable that some deposits- In and, near the Phillips River Goldfield will be mined at a future date', There are also several million tons of mariganiferous ;naterial which is too low in manganese. .co.ntent_ for . present requirements. The manganese deposits¦of Western Australia are mostly superficial. They hav' been formed during the Cainozoic Era by supergene enrichment ò6f Precambbrian: manganiferoius sediments, and by deposition from -solution on, or'in caves in, the Cain- ozoic land surface. The manganese in solution was derived from the weathering of Precambrian manganifer.ous s.edimexsts, None of the deposits are of hydrothermal origin, nor are they related to igneous rocks in any war, other than as ultimate source rocks. There is ho evidence-'t.o.:sugge,st that meta- morphism has been responsible for.the emplacement of any deposit. The tenor of the ore varies'aec'ording'to the quantity of gangue in the orebody and- also to the nature of the part- icular ore minerals. The main ore.mine.rals are the oxides pyrolusite and cryptomelane and the 'o'xide-silicate braunite. The main gangue minerals are hematite, limonite and quartz. The deposits of high grade oreò(-above.45 per cent Mn) range in size from 50 tons to many thousands of tons but most of them are in the 500-5,000-tons r .nge .

Jan 1, 1964

By Brian W. Hester

Ore was first discovered at the Kidd Creek mine site during the first few days of December 1963 when a diamond drill hole there cut sulfide mineralization. This event marked the end of the search started 11 years earlier with the conception of a geological idea. Economic forces provided the stimulus needed for the application of this idea but other-events, and legal considerations, also played arole in delaying the ultimate discovery. The location of Kidd Creek is shown in Fig. 1. Management of the then Texas Gulf Sulphur Co. had become concerned in 1951 at the company's declining reserves of native sulfur in Texas. This problem was to be alleviated by new discoveries and development of methods to recover sulfur from sour gas. At the time, however, the solution appeared to lie in the recovery of sulfur from pyritic ores. Canada was chosen as the best country in which to find these ores. Walter Holyk was hired in 1951 to conduct the search. By 1952, he was working in the area near Sherbrooke, Quebec, known as the "Eastern Townships" where mineralization consisting of base metal sulfides in volcanic rocks has long been known. His observations here led him to the then revolutionary conclusion that such mineralization could have formed as part of the volcanic process and not, as was generally supposed at the time, by replacement. On learning of the discovery of similar mineralization near Bathurst, NB, he moved there in the spring of 1953. He was able to utilize his new concept and found the Half-Mile Lake sulfide deposit.

Jan 1, 1991

By J. B. Stubbins, D. F. Coates, K. L. McRorie

Twenty-two pit slides that occurred in two Canadian open pit mining properties are analyzed. Information on the results of laboratory tests of the rocks and a brief description of the geological environment are also presented. One deduction from the study is that slides seem to be predictable by using established theory. This corroboration indicates that, contrary to normal mining practice, the appropriate slope angle should vary with the height of the wall. In addition, if the general ground water level around an open pit can be reduced, the appropriate slope angles of the walls could then be increased by a determinable amount. The ultimate objective of these investigations is to determine the relationship between the percentage probability of failure of any slope designed with specific strength paraheters. With this relationship it would then be possible to determine optimum slope angles. Because of changes in various economic factors, open pits are now being mined to much greater depths than previously. The need to keep stripping ratios low without endanrrerine.-- lives and equipment provides a strong incentive to determine the maximum practicable wall slopes. Applied research work is currently being conducted to establish the methods for analyzing optimum slopes.

Jan 1, 1963

By G. Q. Liu

"The application of oxygen-enriched cyanidation to three Canadian gold ore samples has been investigated. The results showed that the use of oxygen can improve gold dissolution kinetics, reduce grinding time, and lower cyanide and lime consumptions. To obtain the same gold extraction, the required cyanide leaching time was reduced from 48 hours in slurry containing 8 ppm O2 to 12 - 24 hours in 20 ppm O2 slurry. Reagent consumptions were reduced by 23 - 37% for cyanide and by 35 - 54% for lime. There was little advantage to further increasing the dissolved oxygen to 32 ppm from 20 ppm. Gold extraction from the +200 mesh fraction improved 4 - 14% in oxygen-enriched slurry. A general kinetic model derived from the cyanidation of three ore samples can be described by the following equation: <equation>where E is the gold extraction (%) at time t (hours), EI is the ultimate gold extraction (%) , and &apos;P and k are constants depending on cyanide concentration, level of dissolved oxygen, and the characteristics of the ore samples. Comparative studies of conventional carbon adsorption and carbon adsorption in oxygen-enriched slurry have also demonstrated that oxygen enrichment resulted in more favourable conditions for gold adsorption."

Jan 1, 1995

There are a number of examples of how environmental factors have been integrated into the water management aspects of mining projects. The Kingston Lignite project in South Australia, Pine Creek Gold Mine in the Northern Territory, gravel and sand extraction from the Nepean River flood plain near Penrith, and the Olympic Dam Project have all illustrated that consideration of environmental factors can be integrated with project developments, with beneficial outcomes for both the project and the environment.Each of the above cases demonstrated an individually significant environmental issue, directly related to the interaction between the proposed project and its environment. In each case, careful research and an integrated approach to the problem resulted in a solution that gave both maximum protection to the environment and optimum consideration to the economic feasibility and success of the proposed project.The solutions ranged from alternative mining methods and improved waste and water management through to the ultimate objective of converting a mining project into a major water-based recreation source. These examples have set a precedent that will contribute ignificantly to the successful development of future projects.

Jan 1, 1988

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By Henderson N, Schaap H

In large companies with mining operations spread over multiple sites, it is essential that consistency between sites is maintained in preparing and classifying resource and reserve estimates. The endorsement by The AusLMM and AMIC of the "Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves" and the subsequent incorporation of reference to the code into the ASX listing rules for mining companies has provided a basis for the consistent classification of resources and reserves. However, compliance with other criteria more or less stringent than the Australasian Code can present some reporting difficulties. Examples include listing requirements for foreign stock exchanges, particular Acts of Parliament that may apply to individual leases, constraints imposed by individual companies on their own leases, and ultimately, reserves for short, medium and long term planning. Confusion can arise when any two or more sets of reserves for the same lease are compared.. To alleviate this confusion, a standardised procedure was developed for the calculation and classification of coal resources and reserves. The procedure which is geostatistically based incorporates a technique called "Irregular Block Kriging" where specific mining blocks are directly kriged. The procedure has enabled those engineers and geologists with only a basic understanding of geostatistics to apply the technique and not feel hampered by some of the complex mathematics which in the past has tended to inhibit and overcomplicate the use of geostatistics. The procedure has resulted in "cleaner" data bases and hence more reliable reserve estimates.

Jan 1, 1990

By Frederick K. Allgaier

As part of an ongoing research program, the Bureau of Mines, U.S. Department of the Interior, is monitoring surface subsidence over six longwall panels at three Utah coal mines. These sites are characterized by mining depths of 244 to 610 meters (800 to 2,000 ft .), thick and massive sandstone layers in the overburden strata, multiple seam mining, extraction heights of approximately 1.8 to 3 meters (6 to 10 ft.), and rugged surface topography. Maximum subsidence, angle of draw, timing relative to mining, horizontal strain, and rate of subsidence development are being determined and correlated with mining and geologic variables. Results to date indicate the maximum vertical subsidence over the monitored panels ranges from 0.6 to 0.9 meters (2 to 3 ft.). The major factors controlling the amount of subsidence are the panel dimensions and the status of adjacent panel mining. Only minor surface cracking at the panel ends was evident at any of the sites. In all cases, there was a time lag of several months between the start of mining and subsidence at the surface. As subsequent panels are monitored and additional data become available, better estimates of the effect of various site characteristics on the subsidence will be possible. Ultimately, improved prediction capabilities will allow mine operators in the West to evaluate the potential for subsidence-related damage which could affect the current or future land use above the mine.

Jan 1, 1982

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

By Klenowski

Rational design of layouts for longwall operations is greatly facilitated by use of an accurate and economical method for predicting stresses and displacements. The displacement discontinuity method (a form of boundary element method) is based on replacing actual excavation geometries by thin slits of the same plan area. This approach allows three-dimensional stress- analysis at a fraction of the cost of alternative methods. The analyses can be readily performed on economical microcomputers, putting the analysis capability within the reach of mine-site personnel. This paper describes investigations associated with the German Creek Central Colliery, the first longwall operation in Queensland&apos;s Bowen Basin. The material properties used in the model, in particular the rock mass and goaf properties, have been &apos;tuned&apos; to fit stress measurements obtained during extraction of the first and second longwall panels at the mine. The study shows that model predictions based on suitably scaled anisotropic rock strata properties are in good agreement with the stress measurements made to date. This model predicts average chain pillar loads significantly higher than predicted by models based on United Kingdom conditions. A working chain pillar design method is proposed using average pillar loads predicted by the numerical model and ultimate strength characteristics given by Bieniawski&apos;s formula.

Jan 1, 1988