Search Documents

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By K. C. Heald

THE places where, yesterday, oil was unknown contain tomorrow's fields. Unquestionably, some states that now yield little or no oil have great potentialities, and developments in these states, although perhaps of less immediate interest than those in regions where great pools now exist, may easily be of greater ultimate importance than the results of exploration closer to known fields. Not long ago, Montana had only a quarter of an oil pool, and that was regarded by many as an accident that had strayed from Wyoming. More recently, the northern line of Louisiana was a dead line that would not be crossed by any Louisiana operator who valued his reputation for sanity. Within the past few months, Colorado has shown that it is far from being a negligible factor in the oil supply of the Rocky Mountain states, and it is now known that western Kansas, long shunned by many reputable geologists and operators, should be reckoned with. There may be a vast difference between what a wildcat well yields and what the well signifies. The fact that no commercial production is encountered may be lamentable and may well be disastrous to an individual or a company, but the same well that spells ruin to one may convey to another the information that will result in opening a new field. In presenting the conclusions, in this paper, the writer recognizes fully the possibility of erroneous deductions, particularly since he has had contact with only a few of the wells that are mentioned. Information comes principally from the scout. maps and files maintained at the Geological Survey by M. E. Latimer and G. K. Drach, without whose cooperation this summary would not be possible, supplemented by some personal contact and second-hand information gained by. conversation and correspondence. However, it is felt that the data contain few errors, and that the conclusions are at least reasonable.

Jan 3, 1924

By Stephen Burke

THE oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combus-tion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the condi-tions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 21120 + 702 --> 2FeSO4 + 2H2S04 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to dis-close any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1937

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By Denby B, Miles N. J

The underlying theory behind the construction of an on-line size analysis system is described together with an introduction to the Artificial Intelligent techniques that it is founded on. Previous systems based on more traditional technology such as edge detection and dilation algorithms have been restricted by the significant processing power they require, this has resulted in the production of systems with either reduced functionality or severe hardware requirements. A neural network approach offered a new perspective to the problem of size analysis; the ability of a network to learn and recognise subtle patterns in training data before on-line processing is initiated opened up the possibility for the production of a fully functioning practical system. The format of the training data had to be carefully analysed prior to its implementation in a neural network as the capability of a neural network solution depends as much upon a suitable data preparation as it does on the system architecture. To facilitate experimentation with various profile quantification techniques such as fourier and fractal analysis an Image Profile Analysis System was constructed (IPAS) in software on a personal computer. The IPAS system was produced with the aim of pre-processing image data to create data sets for experimenting with external neural network packages. The system allows the analysis of both real images obtained by image capture and simulated images created by an in-built in simulator. A measurement comparison scheme is also included together with a case study concerned with the frequency analysis of simulated images. The power of neural networks combined with the data compression provided by profiling removes the need for direct measurement of individual particles. This has obvious implications on the level of hardware necessary, and ultimately the expense of a stand alone system. The extrusive nature of data collection via an image analysis system will also permit simple installation of a shipped system; eliminating any requirement for interference with existing machinery.

Jan 1, 1995

By M. Muskat, H. G. Botset

Any information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undisturbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a, method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamination by penetration of drilling water, since this problem has been extensively studied by other investigators.1-3 Furthermore, it was regarded as outside the scope of these experiments, which were concerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essential and obvious procedure is to vary systematically one factor or condition while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program. The procedure adopted was essentially very simple, and consisted merely in filling a given core with fluid (gas and oil, gas and water, or

Jan 1, 1939

By John R. Freeman

The die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the minimum amount of scrap to be sheared from the pressing as it comes from the die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

By James Kitson, Abram S. Hewitt

I HAVE now the duty—the very pleasant duty—to perform, of presenting to the Hon. Abram S. Hewitt the Bessemer gold medal for distinguished services to the iron and steel trade. When this matter was brought under consideration in London it was well known that, as Mr. Hewitt would be the first to acknowledge, there is more than one man in America upon whom we would gladly have cm ferred this distinction, and to whom this merit might be justly at tributed ; but Mr. Hewitt has been long known to our distinguished members on the other side of the Atlantic as one of the most active minds in the investigation of new methods of manufacture, and one of the most enterprising metallurgists on this side of the Atlantic. Well, gentlemen, we proposed to Mr. Hewitt that he should receive this gold medal, but I think it is quite right, and is his due, that I should state that he at once declined to receive it; and he declined in a manner which rendered it impossible to any one but very per sistent friends and very obstinate Englishmen to refuse. When we heard that our American friends had conferred once more upon Mr. Hewitt the distinction of President of the American Institute of Mining Engineers, and particularly with reference to our contem plated visit, and when we heard that he had been elected unani mously to that position, we felt that we had received the stamp of approval from this side. Gentlemen, as I said before, Mr. Hewitt has long been known to many of us in England as an advocate of scientific education. A report which he made of the metallurgical products at the Paris Exposition in 1867 was one of the matters which drew very clearly and distinctly the attention of the English iron and steel trade to the necessity of further improvement in our technical education as to iron and steel; and it was one of those beginnings which led ultimately to the foundation of the Iron and Steel Institute. The development of the ideas which 'he there investigated undoubtedly led

Jan 1, 1891

By David B. Reger

Oil and gas and their derivatives continue to be stable products in West Virginia. In the midst of the cataclysmic happenings of 1930 to 1934, which have swept away banks and practically destroyed many other enterprises of presumably nonspeculative character, the possession of a royalty or working interest in a few old oil or gas wells has prevented disaster in literally thousands of homes. These old wells yield their daily quotas of basic commodities, which the public must have. Fortunately, the facilities of disposal in the Appalachian Province are so ample and well managed that the owner of such equities may be reasonably certain that his proportionate share of existing markets will be afforded him without much effort on his part. In most cases these investments are free from encumbrance or hypothecation, therefore the main uncertainty is the date of ultimate exhaustion at the source. Generally, this is known to be fairly remote. The net result has been that individual owners part with such investments only as a last resort. In sharp contrast to the action of the small owner of wells or royalties who has prudently refrained from jeopardizing his rather certain income by drilling new wells that may be failures, or of which the product may not be needed for the moment, has been the plight of various promotional enterprises in natural gas. Many of these ventures have been operated by amateurish remote control and practically all have been overloaded from the start with bonds and debentures, which could only be satisfied in a rising and expanding market; and with operating costs that have been exceedingly high because of widely scattered producing units and large overheads. Many of these promotions are now in receivership or bankruptcy and in various instances the original units have been recaptured by former owners and have again become profitable by reason of personal operation and elimination of all forms of overhead expense. New Development In 1934, the State issued 524 permits for drilling. According to the trade journals, 553 wells were completed, with 184 oil wells, 274 gas wells and 95 dry holes (Table 3).

Jan 1, 1935

By M Biesinger, R St C Smart

Diagnosis of the surface chemical factors playing a part in flotation separation of a value sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Statistical methods, based on the monolayer-sensitive time of flight secondary ion mass spectrometry (ToF-SIMS) technique, have been developed towards this ultimate aim by measuring hydrophobic species (collector ions, dimers and metal complexes, polysulfides) as well as hydrophobic metal ions, precipitates and added depressant species. Reliable identification of specific mineral particles is central to this statistical analysis. A chalcopyrite/pyrite/ sphalerite mineral mixture conditioned at pH 9 for 20 minutes to study transfer of Cu from chalcopyrite via solution to the other two mineral surfaces, since this mechanism can be responsible for their inadvertent flotation in copper recovery, showed no statistical difference in the copper intensities on pyrite and sphalerite (selected from Fe and Zn images) after this conditioning. Principal component analysis (PCA) identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from sets of data. In images, PCA selects these correlations from the mass spectra recorded at each of 256 ¦ 256 pixels in a selected area of particles. In the image mode, PCA has proved to be a much better method of selecting particles by mineral phase with clearer definition of particle boundaries due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The PCA method has been applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrating extensive CuOH and NiOH transfer between the chalcocite (Cc) and heazlewoodite (Hz) minerals. Statistical differences illustrate the important discriminating depressant action of NiOH in flotation despite the activation of Hz by Cu transfer. The adsorption of the collector at specifically-identified Cu sites has been elucidated by the study. Importantly, the statistical analysis has been able to confirm some mechanisms and deny others proposed to control recovery and selectivity giving more focus on the control factors.

Jan 1, 2005

By M. Muskat, H. G. Botset

Any information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undisturbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a, method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamination by penetration of drilling water, since this problem has been extensively studied by other investigators.1-3 Furthermore, it was regarded as outside the scope of these experiments, which were concerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essential and obvious procedure is to vary systematically one factor or condition while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program. The procedure adopted was essentially very simple, and consisted merely in filling a given core with fluid (gas and oil, gas and water, or

Jan 1, 1939

By R. L. Wilcox, M. L. Fuller

Owing to the nature of the die-casting process, fresllly cast alloys are undoubtedly not at equilibrium from the standpoint of alloy phase relationships. After casting, therefore, they tend to undergo phase changes, with the ultimate effeet of reaching a state of equilibrium at the aging temperature, beyond which no fnrther change takes place. This phase alteration undoubtedly is one of the primary causes of the changes in dimensions and physical properties that zinc-alloy die castings undergo during aging. It is planned to report on this problem in a series of papers of which this is the first. The writers have made a study of commercial zinc die-casting alloys over a period of several years, utilizing the X-ray diffraction technic of determining the phase composition changes in the alloys. Up to the present, two principal phase changes have been observed which are capable of causing dimensional changes: (I) the segregation of secondary constituents from the zinc-base solid solution and (2) the beta aluminum-zinc decomposition. The latter is the subject of the present paper and studies on the former will be reported upon at a future time. Scope of Study In the present investigation a special technic for the study of the beta phase in zinc-alloy die castings has been developed, making possible the determination of the period of existence of the beta phase after casting. The pure beta constituent and its decomposition have been studied in detail. The effect of magnesium and copper on the velocity of the decomposition is reported. The heat of decomposition, the eutectoid temperature arid the accompanying density change have been measured. The density change lias been calculated from data on crystal structure and the result thus obtained has been compared with the actual change.

Jan 1, 1935

By John Langton

In determining what kind of pourer should be adopted for the works of the Moctezuma Copper Co. at Nacozari, Sonora, Mexico, certain considerations imposed by local conditions had to be taken into account. Water.—During most of the year the water-supply is abundant for all purposes, but it dwindles rapidly when the dry season sets in, reaching a minimum flow which is entirely undergrouad. It was evident, that with the greatest care in keeping down the unavoidable loss of water in milling and smelting, these operations and hence the capacity of the works mould ultimately be limited for about two months of the year by the small watersupply available at the period of minimum flow. Transportation.—The nearest railway terminus was in Arizona, at the international boundary-line; and the price of supplies at that point would be enhanced at Nacozari by the additional cost of a 90-mile wagon-haul. During the rainy season, transport to Nacozari was much impeded, and at times made impossible, by the condition of the roads. Hence, to insure continuous operation at the works, it would be necessary to provide for hauling the year's supplies, including fuel for power and coke for smelting, in less than eleven months. In other words, the average freight delivered daily at the works should be at least 10 per cent. more than the average daily consumption. For moderate quantities of freight, pack-carriage by burros is astonishingly cheap. But it has a capacity-limit which is generally very soon reached. A 200-lb. load, and 10 miles a day, 5 with and 5 without load, is the full capacity of a burro. This means one burro per ton-mile of the round trip; and,

Jan 1, 1904

By Jeongbok Seo

This paper describes successful application of driven tapered-steel-pipe piles for two large-scale projects in the New York metropolitan area: Rego Park Mall, Rego Park, N.Y. and 164 Kent Avenue, Brooklyn, N.Y. The combination of side friction and end bearing resistance produced by tapered-steel-pipe piles has been well-recognized as greater than the side friction and end bearing resistance by pipe piles. Forty-four tapered piles were driven and tested at these two sites. Design pile load for the two sites was 260 kips for Rego Park Mall and 400 kips and 300 kips for 164 Kent Avenue. To measure the pile-drive hammer efficiency, the compressive stress in the pile, and to estimate the ultimate bearing capacity of the pile, dynamic load testing using a Pile Driving Analyzer (PDA) was conducted on index piles at the sites. Subsequent to the field testing, data analysis using the Case Pile Wave Analysis Program (CAPWAP) was conducted. Restrike PDA analysis and full-scale static load tests were performed on the selected test piles. Test piles at the project sites exhibited significant time-dependent increases in bearing capacity caused by the effects of "set-up" or "soil freeze." The dissipation of excess pore-water pressure in the soil, which had been disturbed and remolded by driven pile, was generally considered the primary cause of set-up. The increase at the subject sites ranged from 100 to 300 percent of the capacity measured at the initial driving. This paper discusses the results of various types of load testing on tapered piles and the set-up effects by comparing PDA test results acquired during and after pile driving. Finally, an empirical relationship for the New York metropolitan area has been offered for quantifying set-up.

Jan 1, 2008

By R. L. Wilcox, M. L. Fuller

Owing to the nature of the die-casting process, fresllly cast alloys are undoubtedly not at equilibrium from the standpoint of alloy phase relationships. After casting, therefore, they tend to undergo phase changes, with the ultimate effeet of reaching a state of equilibrium at the aging temperature, beyond which no fnrther change takes place. This phase alteration undoubtedly is one of the primary causes of the changes in dimensions and physical properties that zinc-alloy die castings undergo during aging. It is planned to report on this problem in a series of papers of which this is the first. The writers have made a study of commercial zinc die-casting alloys over a period of several years, utilizing the X-ray diffraction technic of determining the phase composition changes in the alloys. Up to the present, two principal phase changes have been observed which are capable of causing dimensional changes: (I) the segregation of secondary constituents from the zinc-base solid solution and (2) the beta aluminum-zinc decomposition. The latter is the subject of the present paper and studies on the former will be reported upon at a future time. Scope of Study In the present investigation a special technic for the study of the beta phase in zinc-alloy die castings has been developed, making possible the determination of the period of existence of the beta phase after casting. The pure beta constituent and its decomposition have been studied in detail. The effect of magnesium and copper on the velocity of the decomposition is reported. The heat of decomposition, the eutectoid temperature arid the accompanying density change have been measured. The density change lias been calculated from data on crystal structure and the result thus obtained has been compared with the actual change.

Jan 1, 1935

With the advent of the First World Conference on Sampling and Blending (WCSB1) in Denmark in 2003 and the subsequent biannual meetings, together with other sampling conferences held on a regular basis, the central tenets of sound sampling practice and theory are spreading throughout the minerals industry. End-users and project houses, or groups who execute the projects, are all now better-informed about the principles of ?correct? sampling and preparation. To support this, many large mining companies now have their own in-house champion who will advise and ensure that the supply of sampling equipment is correct in terms of design and application, which further contributes to improved metallurgical accounting. The presence of a sampling champion also ensures that consistent and acceptable standards in regard to sampling practice are maintained throughout the group. This has, in turn, placed a greater degree of responsibility on the shoulders of sampling equipment suppliers, in terms of their equipment designs and product offerings, as well as applications knowledge for effective installation of equipment on client plants. This paper attempts to highlight the significant challenges that sampling equipment manufacturers often face with regard to complying with the newly understood requirements of best practice and sampling equipment design. Manufacturers invariably face issues with end-users or project houses, including project cost control, restricted headroom for samplers in plant layouts, and a lack of knowledge in certain quarters. These all have a potentially negative effect on the final outcome of a proposed sampling solution or implemented project. In reality, what is intended by all parties and what is ultimately installed are at times very different, with undesirable consequences for all concerned. Against this challenging background, there are, however, a number of instances where intent and implementation are complementary, with very satisfactory results. Keywords sampling, mechanical samplers, design, installation, sampling theory.

Jan 1, 2014

By Eric Brandner

Expansive soil formations can be found throughout the United States. When subjected to wetting, many of these formations have the potential to swell and exert large uplift forces which can significantly damage lightly-loaded structures. Designing an economical foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material, or drilled shafts, can be costly and problematic. Piles made from recycled polymer materials may provide a solution. Due to a lower coefficient of friction along the interface than piles made from traditional materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure which minimizes the risk of significant structural damage. This paper presents the preliminary results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six 13 in. (330 mm) diameter recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. The piles varied in length from 15 ft. to 25 ft. (4.6m to 7.6 m). Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity, while the additional four piles are being subjected to long-term monitoring of uplift movement. A cast-in-place concrete pile, with a diameter of 6 in. (152 mm) and length of 15 ft. (4.6 m), was also installed at the test site for monitoring. The preliminary results indicate that the use of solid recycled plastic piles is a viable alternative for support of lightly-loaded structures in expansive soil environments.

Jan 1, 2009

By Neal Harries

The monitoring of rock slopes is a common procedure in the management of hazards associated with slope instability. Slope stability radar has become widely accepted as the state-of-the-art method for management of hazards associated with unstable slopes in open pit mines. This is confirmed by the rapid adoption of the technology since inception in mid 2003, with over 70 GroundProbe slope stability radars now in use at open pit operations throughout the World. The use of a monitoring system such as slope radar to identify slope hazards is only part of the solution to minimise the consequences associated with slope instability. The presence of the hazard must also be effectively communicated to the mine personnel, so that the correct response to the hazard can be enacted, and the risk mitigated to an acceptable level. In some surface mines, due to the geotechnical characteristics of the rock mass, hazards can develop rapidly; with slopes progressing from stability to ultimate collapse in just hours. In these situations, it is vital that efficient systems are developed to evacuate the area of the pit affected. Such a system has been developed by GroundProbe in South Africa, with the vital driving force for the project being provided by the Anglo Platinum Mogalakwena mine operation based at Mokopane. The mine based development of the system was perceived as an essential aspect in the development of the successful system. From an early stage, the mine provided essential input on both hardware and software developments to allow the system to be rapidly integrated into the mining operation. This paper describes the pit evacuation alarm system that was developed and discussed the benefits obtained from a mine based development program.

Jan 1, 2008

By T. W. Harris

This paper was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the reduction of individual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States in order to consolidate the information developed from the many hundreds of boiler tests on coals consumed by various coal-burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal data, including description of coals used (with sufficient space to include first, second and third preference) on source of coal used, complete analysis and factors affecting choice of coal used. 3. Plant data, divided into: (a,) hand-fired, (b) overfeed stokers, (c) underfeed stokers, (d) traveling grate stokers, (e) pulverized coal; and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency data and remarks. The questionnaire was drawn up by consultation with various combllstion engineers, including B. J. Cross, Test Engineer of the Combustion Engineering Co., W. H. Fulweiler, of the United Gas Improvement Co. and the U. S. Bureau of Mines. In all, 11,538 copies of the questionnaire have been distributed, of which 4369 were sent in duplicate. Our estimate of the total volume of bituminous coal consumed in stationary steam boilers over the 12 months of 1930 is approximately

Jan 1, 1934

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981