Search Documents

By Brook W. H

The history of the reduction of iron from its ores is lost in antiquity. Archreologists state that man has practised it for over four thousand years. Until comparatively recent times charcoal was the principal reducing agent for making metallic iron from its various oxidised ores. Coke was first used by iron founders in England in 1619, and its use spread gradually throughout the civilised world from then onwards. Indeed, the destruction of forests to obtain the requisite charcoal made the iron founders, both in England and America, extremely unpopular, and this hampered the iron industry to a considerable extent, until coal provided the metallurgist with a new and better fuel--coke which is used by most pyro-metallurgists today. The transition from wood to coal products for iron smelting had a profound effect on the location of iron works. Particularly was this the case in America where, in the infancy of the industry, practically each of the early States had its own iron producers, but as coal and coke replaced charcoal, there came about a concentration of the iron and steel industry around the coking coal deposits, and so today there are huge steel plants clustered around the soft coal basins in Pennsylvania and Illinois.The development of the iron and steel industry in Australia, which is comparatively recent by world standards, has been cradled in the coal basins of New South Wales. The first steel works of any consequence in this country were built near Lithgow, close by the mines which produced the coal for coking.Incidentally, these works were rather unique in that the three essential materials for iron and steel manufacture-ore, coal, and limestone-were found virtually at the works' back door.When, in 1912, the location of the proposed steel works for The Broken Hill Pty. Co. Ltd. for smelting ore from Iron Knob in South Australia was considered, the site ultimately chosen was at Newcastle, almost on top of seams of satisfactory coking coal. One of the major factors which had determined the site of the steel works was the fact that, about 1912, three tons of coal were required to produce one ton of finished steel product, and the relative economics of ore and coal haulage were much in favour of bringing ore to the coal.

Jan 1, 1947

CHARLES CATLETT, Staunton, Va.-A great many important things have been said in an interesting way but the most startling, to me, is that for 25 years, the price has been in the neighborhood of $1.00, with a minimum of 86 cents and a maximum of about $1.25. It is evident that during all that time the price was inadequate. The amount paid to be divided between the land owner, the capitalist, and the laborer was too limited or too irregular to permit of a healthy condition; yet it is evident that the enormous industrial development of this country was fostered by this very cheap coal, probably the cheapest that has been provided in quantity in any country. I entered the coal business when the price was lowest and my interest and sympathy went out to the man who spent his days in the dirt and foul air of a mine and I was filled with schemes for helping. But at the end of the year, after exercising every economy and in blissful ignorance of proper depreciation and obsolescence, there was still only a profit of 1 cent per long ton for what I think is one of the best coals in the world, the best grade of New River coal. We are now paying a great deal more than we did a few years ago and probably will continue to pay more for some time; but any one who thinks we will not have low prices again is very young or very forgetful. Yet we must have larger profits if the industry is to be healthy, if the three parties to the production are to get adequate returns and be in shape to provide the improvements which will be needed to take the place of and supplement the man-power. This will come when the men are making so much money that the operator wants to replace the man by a machine, and when the operator is making so much money as to be in a shape to make the improvements. He will not put in machinery unless the machinery will save money. We have got to pay a higher prime cost for coal, but engineering skill will teach us how to handle it better and use it more economically, and the ultimate result ought to be of advantage to the public.

Jan 3, 1920

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By R. J. Lee

Asbestos analysis is conceptually simple. The objective, in most environmental analyses, is to determine the number of asbestos fibers per unit area or volume in a sample. The sample may be a consumer product, an ambient air sample, or a water sample. This determination is complicated by several factors: (1) sample collection and preparation, (2) counting techniques, and (3) operational definitions of asbestos in use. Three different definitions have been used in the study of environmental samples and are summarized in Table 1. The analytical procedure and detail required in the analysis vary with the definition of asbestos. Accordingly, this may be the only type of environmental analysis where the definition of a substance dictates the choice of analytical methods, and the rigor demanded of the analysis. Lead, arsenic, or beryllium are sub- stances having a constant definition and the method of analysis chosen depends on the concentration and precision required. However, the meaning of the term asbestos fiber is dependent on the eye of the beholder. Macroscopically, asbestos has certain physical properties that make it highly useful. Rockforming minerals do not display similar characteristics. Now, the question arises as to how three definitions of asbestos came into being. This is a result of two factors: (1) the definition of asbestos on any scale intrinsically involves the morphology or shape of the material, and (2) the advent of the transmission electron microscope permits detection of asbestos fibers and other mineral fragments in a size range where the physical properties of asbestos such as tensile strength, flexibility, or thermal resistance are difficult, if not impossible, to measure. There is a good deal of controversy about which definition is most appropriate for regulatory purposes because of a lack of appropriate health effects data (Cooper, 1978). Most differences of opinion center on the questions surrounding the following: 11 Morphology-Is a 3:l aspect ratio an appropriate medical or physical lower limit for the definition of an asbestos fiber? 2) Length-Are asbestos fibers shorter than some arbitrary length (5 pm) as hazardous as longer fibers? 3) Mineralogy-Is the mineralogical distinction between asbestos and nonasbestos minerals medically significant? While these questions are directly resolvable only with the biological and health effects data, ultimately such data reflects the ability of analytical procedures to fully characterize the materials used in health effects studies on animal models, and to monitor the exposure to particulates with different physical attributes in the workplace or community (Cooper, 1978). The following sections outline the analytical problems involved in distinguishing the asbestos and nonasbestos varieties of the same mineral; the analytical procedures available for identifying asbestos and measuring its concentration in environmental samples; the ability of these methods to distinguish asbestos fibers from nonasbestos particles; and their precision and reproducibility. Finally, we suggest some future directions in terms of definition and procedure that would greatly improve the quality of such analyses. ASBESTOS VS. NONASBESTOS Asbestos that is mined commercially belongs to two mineral families; amphibole and serpentine (Zoltai, 1978, Wylie, and Steel, 1978). The

Jan 1, 1986

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By William L. Langdon

PRELIMINARY COMMENTS Recent years have been difficult for the mining industry, as reported in the most recently published Minerals Yearbook (Volume III), the estimated value of world crude mineral production has been generally declining since an historical peak in 1979 (16).* The costs of mineral extraction have, however, been rising rapidly. Individual project costs are, in general, exceeding the growth rate of mining companies, while operating and technical risks continue to increase (16). Risks resulting from currency flotation and political actions in the host country are also on the increase. Labor difficulties (such as those experienced by Phelps Dodge) and the Reagan Administration's recent rejection of a proposal by the International Trade Commission for higher tariffs and/or quotas on copper imports have also contributed to the mining industry's difficulties. The net result of these factors has been financial difficulties for mining companies with respect to paying for their current financial obligations as well as trouble finding new financing. It may be that one of the main factors in determining the future of the mining industry will be centered upon capital structure, i.e. how its assets are financed. Historical Perspective on Capital Structure In The Mining Industry As discussed by Isreal Borenstein in (4) and Thomas Navin in (7), mining firms typically have used a financial model based upon high financial leverage, i.e. large amounts of debt relative to equity. This has been especially true for American firms developing orebodies discovered overseas. Problems sometimes occurred for those who were forced to commit themselves to completion guarantees in order to obtain bank loans. Mines under these circumstances must be brought into operation regardless of market conditions. Politicians in overseas countries also may use the high profits required by these high risk ventures to argue for nationalization of mines. Coupled with the frequent use of high leverage, mining companies traditionally have paid out a higher percentage of earnings in the form of dividends than manufacturing firms. This is significant, in that such funds paid out in dividends are not available for other uses. Hence, a greater reliance upon debt and/or additional stock issues than would ordinarily be the case for manufacturing firms. Thomas Navin has stated in (7), that the theory behind the high dividend payout was that, "most mining investors thought of themselves as investing in a wasting asset, one that would gradually deplete over time until it ultimately became valueless." Investors, therefore, required a receipt, in the form of dividends, of a percentage of current earnings and a return on original capital. This view of reality, apparently, has not changed in some quarters, even though modern mine management ordinarily replaces depleted mines with new ones. It may be that this practice of high dividend payout coupled with relatively high financial leverage should be reexamined. Current capital structure theory could prove interesting and useful for those concerned with current conditions. Capital structure patterns and related practices in this industry are not, in many cases, congruent with those thought by some to be theoretically optimal. Prelude to Capital Structure Discussion With a few notable exceptions (such as the Guggenheims and Anaconda's chief operating,. officer in 1971) mining companies' chief executives and boards of directors have not been persons with financial backgrounds. This, one could conjecture, might have accounted for the relatively nonsophisticated nature of capital structures of mining companies. In order to appreciate the possibilities with respect to alternative influence on a firm's performance, one must be acquainted with the basics of financial theory. This paper is an attempt to familiarize the reader with (1) capital structure in general, (2) the usual components of this structure, (3) the general theory behind the use of financial leverage, and

Jan 1, 1985

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

By Jr. Fackler

The ionization potentials of gaseous Group 11elements are similar, with Au(0) being 1.5 eV greater than the next highest member of the group, Cu(0). The ionization potentials are all very much greater than the alkali metals, making these ?coinage? elements rather unreactive to chemical oxidation. Ionization from the first oxidation state shows a different pattern, with Ag(I) being the most difficult of the Group 11 ions to lose an electron. Gold(I) is noble and only normally oxidized in the presence of strongly coordinating ligands such as thiols or cyanide. Gold(I) compounds are 2-, 3- and 4- coordinate, with 3-coordinate species generally showing visible photoluminescence under UV excitation. Dinuclear Au(I) compounds with strongly coordinating S or C ligands can be oxidized to form isolable metal-metal bonded Au(II) compounds which are often readily isolable. Many have been structurally characterized. T he ease with which electrons are lost from closed shell dinuclear sp ecies (with anti-bonding M-M interactions) increases when metalmetal bonded compounds are formed. T his observation was made by our group with oxidative-addition studies of dinuclear gold(I) ylide complexes. It was superbly demonstrated recently by Cotton?s group who reported the isolation and characterization of a dinuclear closed shell transition metal species which is more readily oxidized than cesium. Trinuclear Au(I) pyrazolates, TR(pz), carb eniates, TR(carb), and benzylimidazolates, TR(bz), are well known and undergo electron loss through oxidative addition forming Au(I,III) mixed valence species and ultimately trinuclear Au(III) species. Au(II) species are absent from isolation in these oxidations. These carbeniates and benzylimidazolates also are excellent bases for metals ions such as Tl(I) and Ag(I). The acidic, neutral trinuclear compound [Hg(C6F4)3]3 also interacts with these bases. We have also shown that the neutral organic pi acids C6F6 and TCNQ form stacked pi-acid pi-base products with the trinuclear Au(I) compounds. In this paper, the structure of the octafluoronaphthalene acid-base product will be described. It displays a feature not observed previously in that the product is photoluminescent with a bright yellow emission. The 3.5 ms lifetime is very long and reminiscent of the long lifetimes observed by Balch for the stacked methyl,methoxy Au(carb). The electrochemical oxidation of tetragold(I) clusters, [Au4(form)4] have been studied in 0.1 M Bu4NPF6/CH2Cl2 at Pt working electrode at different scan rates. Three waves are obtained at 0.75, 0.95, and 1.09 V vs Ag/AgCl at scan rate 500 mV/s. The potential of the three reversible waves is independent of the scan rate in the range 50 mV/s to 3 V/s. The current at the third wave is larger than those at the first two waves. These tetranuclear species app ear to be effec tive catalyst precursors for the oxidation in air of CO. Introduction. The electronic structural relationships of the coinage elements and the alkali metals are similar in the sense that each have a [closed shell]ns1 configuration, yet their ionization energies (Table) and chemistries are clearly vastly different. The Group 11coinage elements have an underlying nd10 level immediately below the ns1 level. Unlike the alkali elements, ionization leaves the filled d electron shell the next accessible for further ionization. The coinage elements are all relatively ?noble?, much less reactive to environm ental conditions than the alkali metals. With the coinage elements, oxidation becomes very much dependent upon the types of ligand s availab le to bo nd to the ionized state.

Oct 1, 2003

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada's gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world's largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By Michael A. Gustafson, Fernando B. Sotelino

INTRODUCTION The degree of success of any new project will ultimately depend on two factors: (i) the underlying economic strength of the project; and (ii) how successfully the parties involved can coordinate their interests to establish a financing structure which indeed capitalizes on the project's inherent economic attractiveness. A project's underlying economic attractiveness is determined by its inherent comparative advantage in accessing the factors of production, combining these factors of production to create a product and marketing this product. Initially, the decision regarding whether to go ahead with the project - the go/no go decision - has to be based on its total ability to generate cash flow returns to project participants to compensate them for resources committed and risks undertaken. The extent to which project sponsors will actually benefit from the project's inherent economic attractiveness is fundamentally dependent on their ability to establish the long-term financing arrangement which best meets the objectives and constraints of each project participant and sources the most advantageous funding. The decision regarding the financing of the project, the "how-to-go" decision, is then an attempt to find the capital structure, consistent with market terms and conditions and sound financial management policies which will best: (i) match planned outflows with cash inflows; and (ii) maximize the return for project sponsors. This article makes use of a case study to illustrate the analytical process involved in dealing with the go/no go and the how-to-go decisions on a project. Though most commonly applied to project finance situations, the guideline described herein is equally applicable to other financing situations, such as leveraged buyouts and debt restructurings, where timely repayment of debt depends largely on the future cash flows to be generated by the entity being financed. Our case study is of a hypothetical expansion of an existing copper mining operation in Latin America. The company, Latin American Copper (LAC) currently has 147 million metric tons of proven sulphide ore reserves. The existing mine complex consists of an open pit mining operation and a conventional flotation plant with a processing capacity of 20,000 metric tons of ore per day. LAC sells copper concentrates primarily to Japanese custom smelters. The mine has been in operation for 5 years, fine copper production last year was 108,240 metric tons, and LAC currently has assets of $175 million and net worth of $135 million. Due to a recent increase in proven reserves, LAC is considering doubling the treatment capacity of its flotation plant to 40,000 tons per day, and expanding its mining capacity to meet the additional concentrator capacity (the "Project"). Project capital expenditures and incremental working capital have been estimated at approximately $210 million. The construction period is expected to cover one year, including a three-month start-up phase. The Project is to be funded by a combination of equity, senior debt, including both supplier credits and/or commercial bank term loans, and subordinated debt. LAC's shareholders are willing to commit a maximum of $50 million to the Project. A government development agency, which is also a minority shareholder, might be willing to lend approximately $40 million to LAC in the form of subordinated notes, depending on the ability of the Project to generate foreign exchange reserves. Commercial banks cannot be expected to offer loans with maturities longer than ten years. The Project is expected to increase the value of the firm because: (i) It will solidify the Company's position as a low-cost copper producer by taking advantage of economies of scale. As a result of the expansion, cash production costs are expected to decrease 7.0[c]/lb. and all-in costs 11.0[c]/lb; (ii) The potential earnings stream from the sulphide ore reserves will be realized

Jan 1, 1985

By W. B. Wise, H. D. Attra, W. M. Black

The purpose of this paper is to illustrate a comparatively new approach for solving a problem that has plagued oil producers for many years—how to make the most money with available field production capacity. In a very basic operation such as a top-allowable one-well field, a computer and staff of engineers are not required to determine that the best operation is to produce that well at its maximum for as long a time as it will produce. However, as the problem becomes more complex and the number of wells and number of reservoirs increase, it probably will be a wise choice to devote some engineering thought and calculation time to determine the best way to operate that field on both an ultimate and day-to-day basis. Continued developments in the field broadly referred to as "operations research" have led to a number of useful engineering analyses for optimizing field operational problems. One of these techniques, termed linear programing, is parlicularly interesting because of its potential applications to the study of complex oilfield operating problems. Linear programing is concerned with the problem of planning a complex set of interde~endenl activities in the best possible (optimal) fashion. A field application of linear programing is being used to maximize daily income from a multi-reservoir producing operation. The initial results of this study indicate that the linear programing technique (I) can be applied effectively to field problems, (2) can be used to detect unsuspected avenues for improving operations and (3) can effect a significantly improved means of controlling field operations through the use of the highspeed computer. INTRODUCTION The usual approach for studying complex field operational problems has been to look in detail at several basic plans suggested by judgement and experience and, then, to choose the best plan from those investigated. This approach is entirely satisfactory provided: (1) that judgment and experience alone will reliably pick the best or near the best program as one of the plans to be investigated; and (2), and most important, that the factors which control field production will not change. This paper deals with the large group of field operations which are at least one-step removed from a satisfactory solution using the conventional method of analysis. Problems such as pipeline- and gathering-system design, transportation studies, large field development projects and multi-reservoir producing operations fall in this latter category. To find the best program for handling these problems when the best program is not obvious, a complete optimization study is required, and high-speed computers are required to continually update the program once it is selected. Operations of this type have an extremely large number of possible solutions. However, only one will result in maximum economic return and, more important, this one program must be re-evaluated and adjusted constantly to accomodate such changing field factors as the number of producing days, the price of crude, the discovery of new reserves, declining reservoir pressure with subsequent decline in production and a host of other factors which characterize specific operations. One of the most widely used, direct methods of optimization is a numerical procedure termed "linear programing", which is designed to investigate systematically each of the possible solutions involved in a given problem, determining rapidly and uniquely the optimum answer. As implied by the name, linear programing requires that all field variables be either defined or expressed in a series of interdependent linear equalities or inequalities. These relationships are solved simultaneously, using a form of matrix solutions to determine the optimum values for each producing variable that will maximize net profits. The solution techniques used in a recent field case study is termed the "simplex method" and is discussed in full detail in Ref. 1.

By J. B. Agan, R. J. Fernandes

This paper utilizes the layered-system approach, modified to include areal sweep efficiency, to determine the miscible-slug size required and to predict the perfort7zance of a miscible-slug process in a highly stratified reservoir having a permeability variation of 0.76. The slug size in each layer was determined from theoretical calculations and laboratory data which showed that, to maintain miscibility in the reservoir, the slug size had to be 8.2 per cent of the floodable hydrocarbon pore volume. Economic considerations, however, such as the value of the miscible product injected, the cost of injection and the cost of reprocessing the miscible product, limited the amount of miscible product which could be injected into the lower-permeability layers. This resulted in subjecting only 60 per cent of the reservoir to a slug size sufficient to maintain miscibility. Utilizing the relationship of producing gas-oil ratio and areal sweep efficiency as a function of pore volume injected (as obtained from data published by Dyes, Caudle and Erickson2), the theoretical performance was determined. This prediction is compared with actual performance to date. Actual performance reflects an increasing percentage of tniscible product in the produced fluid to a particular level, which remains static for a short period and then increases again to a higher level. This performance suggests that the reservoir has performed as a layered system. It is concluded that the layered-system approach can be used to predict performance in a highly stratified reservoir and that economic consideration is a limiting factor in determining the amount of the reservoir which can be miscibly swept. INTRODUCTION The Paloma zone in the Paloma oil field, Kern County, Calif., is comprised of several sand members separated by siltstone, shale and/or cherty sections. Rapid facies changes within the zone indicate that the sediments were deposited in a "near shore" environment. As a result, the Paloma sands have a high permeability variation, and the Paloma zone is comprised of several sand reservoirs. Since one of the sand reservoirs containing crude oil was not receiving the benefits of gas injection, consideration was given to recompleting certain wells to isolate the sand in order to perform a miscible-phase injection project and, thereby, to increase its ultimate oil recovery. Before proceeding with the project, a review of the literature was made to determine the miscible-slug size that would be required to maintain miscibility throughout the displacement process. Although the review showed that considerable information was available for homogeneous systems, insufficient information was available to determine slug-size requirements and to predict performances for a highly stratified reservoir. This paper has been prepared to describe the method used to determine the miscible-slug-size requirement and to predict the performance of the miscible-phase injection project initiated in the Paloma oil field. Although the Paloma project has only been in operation since Aug., 1958, sufficient production history has been obtained so that a comparison can be made with the predicted performance. DESCRIPTION OF RESERVOIR The reservoir in which the miscible-phase project was initiated in the Paloma field is shown on Figs. 1 and 2. Reservoir properties are as follows: average sand thickness, 43 ft; porosity, 19.1 per cent; water saturation, 47.2 per cent: oil viscosity, 0.328 cp; reservoir temperature, 250°F; reservoir pressure, 3,500 psi: gas saturation, 21.2 per cent at time of miscible product injection; and total net hydrocarbon pore volume, 19,993,000 reservoir bbl. LIMITATIONS The method described herein utilizes a layer-system approach, where injection into and production from each layer is assumed to be proportional to the layer's fractional capacity. The effects of increased fluid mobility on injection and production rates, in layers which have had breakthrough, are not reflected in this method. There has been considerable controversy over the slug size necessary to maintain miscibility throughout the displacement process. In this method, the slug-size

By John S. Brock

INTRODUCTION The Oxford Dictionary says that the word "promoter" has usually been used in an opprobrious sense since at least 1876. This popular image of mining promoters is of cigar-chomping shysters and Brooklyn-Bridge vendors, improving their standard of living with the aid of funds raised through the sale of stock to little old ladies. It is unfortunate that mining promoters are considered crooks until they can prove their integrity and honesty by finding a mine. A common rule of thumb states that for every 1,000 prospects, 100 come to be drilled, and one becomes a mine. However, it is also a statistic that there have been mining promotions, where money raised has gone elsewhere than into the ground; Junior exploration companies can be handy vehicles for unscrupulous financial activity. One must remember though that every stock exchange has had its share of sound mining promotions that, because of the one in 1,000 odds, have failed for legitimate reasons. The promoter must be able to rationalize the worth of a mineral discovery which, on an industry- average basis, probably cost more to find than the discounted value of its net return, which return is not an assured percentage of invested capital, and furthermore, is ultimately from a wasting asset. So, it is easy to understand why the promoter must constantly justify the credibility of his operation to his grubstakers during the course of the "five phases of exploration," those being (1) euphoria, (2) disillusionment, (3) search for the guilty, (4) punishment for the innocent, and (5) distinction for the uninvolved. The promoter with the exploration organization that does not have the benefit of positive cash flow, by definition for the sake of this article, works for a promotional outfit, a Junior Company, that must raise its exploration budget from a variety of sources. Promotion, as discussed here, will not entirely refer to the formation and operation of a joint- stock company but rather to the overall methods of raising risk capital for mineral exploration ventures from outside sources. THE NECESSITY OF PROMOTION In Canada, the publicly financed Junior Company has had an enviable record of mine-finding success. In the Province of British Columbia alone, the discovery of fifteen out of twenty-four mines has been as a result of the activity of the Junior Company (B. C. & Yukon Chamber of Mines, 1977). In the Province of Ontario, one research study indicated that between 1951 and 1974 the 'Juniors' spent only 28 percent of the total exploration funds but were responsible for 62 percent of all economic discoveries (Freyman, 1978). The reasons for the success of the Juniors are tied to a variety of factors, the main one being personal initiative based on incentive. In other words, the principals, or their employees have 'a piece of the action.' The smaller companies can operate faster and more efficiently than their larger counterparts. The Junior Company is also destined to take some bigger risks, the 'long shots,' many of which efforts by virtue of the Junior's perseverance coupled with a touch of 'ore is where you find it' philosophy, result in major discoveries. The individuals, syndicates, private and publicly financed Junior Companies, because of high costs of exploration and development, cannot hope to finance most mineral prospects all the way to production. Exceptions do exist, those being the lower capital cost, small, high-grade deposits. Private investors and publicly financed Junior companies, therefore, can usually afford to finance most exploration through the initial drill-testing stage. The major resource company will enter a mining deal with a Junior Company usually by way of option or joint venture agreement, and will finance to production to earn an equity in the prospect or the Junior Company or both. The conventional lending institutions, banks and government agencies, will usually only participate through loaning a portion of capital

Jan 1, 1985

By Goldye Leeds, Marian Balicki

A SURVEY of literature reveals the scarcity of experimental evidence relating to work hardening and reannealing of silver.'-'" With the exception of the well-known X-ray investigation of silver and other metals by W. A. Wood? the effect of progressive cold working has not been studied. The determination of thermal stability of silver in the work-hardened state by means of isochronal or isothermal annealing has been confined apparently to very high reductions only. In the survey made, no study was encountered which endeavored to produce a complete picture of the changes in various properties due to cold working and subsequent reannealing. To fill these gaps and to assemble data that could be used for the determination of activation energies and of frequency coefficients of primary recrystallization, a systematic experimental approach, which was developed by one of the authors, has been applied to pure silver. Material and Processing The silver used was Handy and Harman fine silver, with a spectroscopic analysis at the testing stage of Cu, 0.0001 to 0.001 pct; Te, 0.0001; Pb, Si, Ca, Mg, and Mn, traces. The material was supplied in the form of a rod 0.406 in. diam and was converted into test samples according to the procedure condensed in Table I. It should be mentioned that air annealing was adopted to simulate industrial practice, though it was realized that annealing in a neutral gas or in a vacuum would be preferred. The usual precautions have been taken to eliminate any structural changes and property changes resulting from the storage of the samples prior to annealing or testing. Thus the wires were kept at the fully annealed stage, and the final wire drawing, which produced the desired degree of work hardening, was done just prior to the final annealing or testing. During the short waiting period, the samples were kept in a thermosflask filled with ice. Even with these precautions some strain-age-hardening or self-annealing could occur. To test such a possibility, wires of different reductions were prepared in the manner adopted and portions of them were immediately tested. The remaining portions were similiarly tested after different periods of storage, both at room and melting-ice temperature. Within experimental error, all samples obtained from a wire of a given percentage of reduction yielded identical values. This result qualified the material for further tests and interpretations, because it showed that either strain-age-hardening and self-annealing were absent, or that these effects fully balanced each other. The final annealing was carried out in an electric resistance furnace automatically controlled to within a 10°F. It was realized that the temperature fluctuations were greater than desired for this type of work. TO diminish the errors due to fluctuations of temperature, the hot junction of the thermocouple was placed as close to the samples as possible; the time of soaking was reduced to 15 min; and the number of samples annealed at different temperatures was increased. It will be seen from Table I that some tests were performed on the same material at rising temperature. These will be discussed elsewhere. Room temperature testing was limited to the determination of some of the mechanical properties that are known to be additive in a degree sufficient to be used for indirect study of the kinetics of the reannealing process, Tensile tests, carried out on a manually operated J. Camillon machine, accurate to within permitted the determination of the ultimate stress (U.S.1 and of the 2 in. elongation, (A,). The proof stress (d,e) has been determined from a series of bend tests carried out on a Tinius Olsen Stiffness Tester by using the offset method. This involved accurate determination for each sample of load-angular deflection curves, finding a

Jan 1, 1952

By Basil Prescott

Resume.—The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre-mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide type occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore, The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition. Introduction The Santa Eulalia district is situated in the State of Chihuahua, Mexico, and lies about 12 miles southeast of the capital, the city of Chihuahua. (See map, Fig. 1.) The district embraces the Sierra de La

Jan 1, 1915

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By W. B. Mather

A RKANSAS is not only a geologist's paradise, but Ait is also particularly fortunate in possessing a wide variety of mineral resources. The future mineral production and mineral industry of Arkansas, like the other states in Mid-America, will probably depend to a large degree on efforts to increase the exploitation of the non-metalliferous deposits of the state. The term nonmetalliferous, as used in this paper, embraces all types of mineral deposits, except fuels, water, and those deposits from which, after bene-ficiation, metals are ultimately derived. For example, bauxite is the ore of aluminum, but a considerable portion of the bauxite mined eventually is employed in the production of nonmetallic alumina, an important oxide in the abrasive and ceramic industries. The bulk of the production, however, becomes metallic aluminum and therefore this type of mineral resource is considered metalliferous and is omitted from this paper. Arkansas' nonmetalliferous deposits are of many different types, too numerous to discuss in detail in a single paper; therefore, only their salient features are presented. Many types of deposits such as limestone, glass sand, novaculite, shale, and sandstone are exposed over wide areas, providing inexhaustible reserves. Other types of deposits, such as barite and tripoli, contain large reserves which certainly are not unlimited. Still other types of deposits, such as celestite, kaolin, and vermiculite, appear to occur in small isolated deposits containing relatively small reserves. Of course, all of Arkansas' nonmetalliferous deposits probably have not as yet been recognized, nor have all of the known deposits been prospected, tested, and evaluated. Various types of deposits are too low grade or too limited in extent to be profit- ably produced by today's standards. In the case of other deposits, the known uses are few in number, thus acting as a retarder to their development. Due to anticipated technologic advancements, the future demands of industry are not expected always to be the same as they are today, and therefore idle deposits or those of current limited production may readily become the important revenue producers of the future. The types of nonmetalliferous deposits discussed here include: clays, shales, and slates; silica deposits including glass sand, novaculite, tripoli, sandstone, chert, and quartz crystals; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; green-sand; phosphate; vermiculite; fuller's earth; ben-tonite; diamonds; sand, and gravel. The location of the various types of deposits are presented on the accompanying map (fig. 1). Symbols indicate the general area of occurrence. Many deposits, such as limestone, shale, novaculite, and so on, are represented by formations which could only be properly shown on a geological map. In these instances only active deposits or those of exceptional merit are indicated by symbols on the map. A general northeast-southwest line divides the interior highland from the Gulf Coastal and Mississippi Alluvial Plains of south and east Arkansas. The data presented in this paper are only a surnmary of a portion of a more comprehensive survey and study of the natural resources of the entire state.' The study was sponsored and underwritten by the Arkansas Power and Light Co., Little Rock, as a public service to the state and its residents. Permission to present some of the data and conclusions resulting from the survey is gratefully acknowledged. Table I, prepared by the Arkansas Geological Survey from state severance tax records, presents the annual production secured from Arkansas nonmetalliferous mineral deposits. Clays, Shales, and Slates Clays: It is realized that each method of classifying clays is prone to criticism. In this paper, Arkansas' clays of potential value are arbitrarily

Jan 1, 1951

By B. L. Averbach, Morris Cohen, S. A. Kulin

The martensitic transformation can be initiated by elastic stresses at temperatures above M. in a steel containing 20 pct Ni and 0.5 pct C. Shear strains and normal tensile strains acting on a potential habit plane promote the transformation but compressive strains oppose it. THE strain sensitivity of the martensitic transformation has long been recognized. It is now well known that martensite formation can be induced by plastic deformation at temperatures below, and not too far above, the M, point.' However, the exact role of elastic vs. plastic strains and of the concomitant stresses has proved to be a very elusive matter. Many investigators2-' of the steel hardening reaction have made use of the stresses resulting from volume changes to account for such observations as the existence of retained austenite and its variation across the section of a bar, the change in the amount of retained austenite with quenching rate, and the self-stopping nature of the transformation when the cooling is stopped. The effect of applied strain as an independent variable has been studied in 70 pct Fe-30 pct Ni alloys by Scheil7 and McReynolds.8 Some data are also available for lithium and Li-Mg alloys,9 Cu-Zn,10 Cu-Sn and Cu-A1 alloys," and aus-tenitic stainless steels."-" It has been found that martensite formation can be induced isothermally, even at temperatures above M,, by mechanical deformation of the parent phase. The competitive nature of plastic yielding by slip and by the martensitic reaction has been depicted by Scheil.7 Basically, Scheil postulated that: 1—at temperatures not too far above M, (where austenite is less stable than martensite), a critical resolved shear stress (within the elastic range) is required to promote the transformation to martensite; 2—at and below M,, the austenite lattice becomes mechanically, as well as thermodynamically, unstable and shears over spontaneously into martensite without the application of external stress; and 3—at temperatures sufficiently far above M8, the critical resolved shear stress for martensite formation increases to a level above that required for slip, and plastic flow then supersedes the transformation when external stress is applied. Scheil's concepts were tested by McReyno1ds8 ho found no change in the elastic moduli (measured both statically and dynamically) of 71 pct Fe-29 pct Ni alloys in the vicinity of the M, temperature. Since the moduli did not approach zero or become negative on cooling to M,, it was concluded that the austenite lattice does not become mechanically unstable at M2, as postulated by Scheil. McReynolds also reported that M, is not raised by elastic stresses. Accordingly, plastic deformation was considered to stimulate the transformation by generating martensite nuclei in the distorted regions of the parent phase. The above issues with regard to the role of applied stress require clarification, if a basic understanding of the martensitic transformation is to be obtained. For example, in the reaction-path theory,'"," it is postulated that strain embryos exist in the austenite that provide part of the activation energy for the nucleation process. These embryos are visualized to be regions of localized strain in which the atoms in the austenite lattice are displaced part way along the path to their ultimate positions in the martensite. Consequently, it would

Jan 1, 1953