Search Documents

By G Smart, D Ward, J Grace

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. It is an underground sublevel cave (SLC) operation mining approximately 5 Mt per annum. Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. These data form the basis for forecasting and on-going systems analysis which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions, visual grade estimates and draw point sampling are routinely recorded. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Draw point recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Statistical variance controls are also employed to analyse mine and plant performance and guide actions.

Jan 1, 2003

By D. C. Martin, P. M. Hawley, C. P. Acott

"In bedded deposits such as coal or sedimentary iron, economic limits of mineable reserves are clearly defined by the footwall of the seams or ore-bearing units. Where open pits are developed in dipping strata, a long, high footwall slope may result. In many cases, unbenched slopes excavated along the base of the lowest mineable seam are operationally simple, economically desirable and geotechnicalty practical, although a variety of failure mechanisms may develop. This paper examines the engineering geology and rock mechanics parameters of importance in the design of footwall slopes. Possible failure mechanisms and stability analysis methods are described. Design considerations for benched and unbenched slopes are discussed with prime consideration given to development of long high stopes without benches or with a minimum number of benches. IntroductionIn bedded deposits, the ultimate depth and economic viability of an open pit in dipping strata may be controlled by the design of the footwall slope. The stability and, hence, design of footwall slopes is strongly influenced by the engineering geology and rock mechanics parameters of the slope forming materials. A clear understanding of the structural geology, engineering geology and tectonic history of the deposit is essential to assess the behaviour of the slope. This is particularly important for long high, unbenched footwall slopes such as shown in Photo I.A rational footwall slope design requires identification and assessment of all possible slope failure mechanisms with respect to the proposed slope geometry. Stability analyses of each potential failure mechanism are used to identify the main controls on slope stability and to develop appropriate slope design criteria. The optimum slope design is based on the most economic and geotechnically practical slope geometry with due consideration of operational constraints and of the possible advantages of specific remedial measures."

Jan 1, 1986

By M. A. Jones

Performance of a pilot flood in eastern Kansas indicates improved recovery and accelerated production resulting from mobility ratio control obtained by adding a high moleculur weight polymer to injected water. Ultimate pilot flood recovery of the 75-cp reservoir oil is anticipated to he 350 bbllacre-ft during the six-year flood life. Cumulative recovery to date totals 242 bbl/acre-ft after 30 months of injection. Reservoir parameters and flood performance are disc~rssed in detail to provide a case history relating to the feasibility of polymer flooding. INTRODUCTION The Vernon Polymer flood of the Brazos Oil & Gas Co., located in Sec. 2, 24 S., 16 E., Woodson County, Kans., was begun in late Oct., 1963. Injection of a 500 ppm solution of Pusher* polymer was initiated in a 15-acre pilot to determine feasibility of improving oil recovery by mobility ratio control. Performance to date and the anticipated recovery of 115,000 bbl from the 329 acre-ft pilot indicate efficient displacement of the viscous reservoir oil. Dependence of flood recovery on the displacing fluid-displaced oil mobility ratio has long been recognized. Displacement efficiency of the reservoir oil decreases with increasing mobility ratio. Therefore, economic reduction of this parameter is an attractive approach to improving oil recovery. particularly from viscous oil reservoirs where mobility ratios are often quite high. Waterflood mobility ratios can be controlled by dilute solutions of certain polymers'; which provide a displacing fluid with considerably reduced mobility. Reservoir parameters and flood performance are emphasized in this paper to provide data relating to polymer flood applicability. THEORY The polymer used in the Vernon pilot exhibits the property of unusually high resistance to flow through porous media.'.' A small concentration in injected water effects a mobility reduction considerably beyond that predicted from increases in bulk viscosity as measured in a capillary or rotating cup viscosimeter. Water mobility in the subject flood is reduced by a factor of 7.55 with the addition of 500 ppm Pusher chemical to injected water while the bulk viscosity is increased from 1.03 to only 1.40 cp at 75F. The exact flow mechanism causing resistance to flow has not been established; however, it is observed only in tortuous flow systems and appears to be influenced by brine properties, rock properties and oil saturation. Consequently, mobility reduction is estimated from flow studies for a given sample of reservoir rock and is expressed in terms of a "resistance factor".' This parameter is defined as the ratio of brine mobility to polymer solution mobility measured at residual oil saturation: RF= ?m/?p= (km/µm)/(kp/µp)M.......(1) where RF = resistance factor (dimensionless) k*. and A, = mobility of water and polymer solution, respectively k,,, and k,, = water and polymer permeability, respectively (darcies) µie and µp = viscosity of water and polymer, respectively (poise). Eq. 1 is similar to the expression commonly used to relate the relative mobility of the water bank at residual oil saturation to oil-bank mobility at irreducible water saturation: where M =mobility ratio of water to oil (dimension-less) A, = mobility of oil k, = permeability to oil (darcies) )i* = oil viscosity (poise). From Eqs. 1 and 2 it is apparent that the polymer-solution-to-oil-mobility ratio can be approximated by dividing the brine-to-oil ratio by the resistance factor RF: Mpn=M10/RF...........(3) where M,-, = mobility ratio of polymer solution to oil (dimensionless). This simplified presentation assumes no dilution of the polymer solution by connate water. Also, the presence of a connate water bank separating the polymer solution from the displaced oil is not considered. Displacement of oil by waterflooding is increasingly dominated by viscous forces as the viscosity of the oil displaced increases. When the oil mobility is less than that of the injected water, the oil-water interface is not a piston-like front.3,' Instead, instabilities occur at the flood front in the form of viscous fingers which tend to penetrate the less mobile oil bank. The magnitude of these protrusions, or the degree of channeling, increases

Jan 1, 1967

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant' on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,' aging took place during the creep tests. 'In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500' or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500' or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40' to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.' At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

By Charles Smeal, Robert J. Schafer, Max Quantinetz

Normally metal powders cannot be ground to sub-micron sizes because of welding and agglomeration phenomena. Through the use of selected grinding aids and grinding fluids, nickel and other metal powders have been ball-milled as fine as 0.1 It was found that certain inorganic salts are more effective grinding aids for metal powders than conventionally used surfactants. METAL and alloy powders are used to produce reagents, pigments, coatings, solders, brazes, and parts for industry by powder metallurgy techniques. They are also combined with refractory compounds to produce cermets and dispersion-hardened products. One of the interests at the Lewis Research Center has been to explore the potentialities of the dispersion strengthening process. Since the work of Ir-mann, many investigators have shown that the strength of dispersion-hardened products may increase with decreasing interparticle spacing.24 One approach to achieving small interparticle spacing is to combine fine refractory compounds and metal powders, preferably below 1 in size. In attempting to obtain fine metal powders, it was found that until very recently the best that could be obtained from commercial suppliers, particularly of ductile metals, was about 1.0 . Interest was therefore developed in providing finer metal powders for dispersion-hardening studies. Information obtained from the literature, from others working in the field, and from prior experimental work performed at NASA, led to a consideration of ball-milling as a technique to produce the desired materials. Some of the variables associated with ball-milling are the size, material, and nature of construction of the grinding container; the nature and amount of the grinding material and material to be ground; and the nature and amount of the grinding liquid and grinding aid, if employed, and the grinding time. In all ball-milling, welding and agglomeration can oc- cur as well as grinding. Because of the tendency of ductile metals to weld together, they are difficult to grind.5 The ultimate particle size obtained on grinding is generally the one at which the rate of grinding becomes equal to the rate of welding. To help delay welding and thus obtain smaller particle sizes, grinding aids are often employed. The principal objective of this investigation was to produce submicron metal powders by ball-milling the powders with selected grinding aids and grinding fluids. A secondary objective has been to attempt to explain the variations observed in grinding behavior by considering possible grinding mechanisms and correlating various parameters with grinding effectiveness. Three groups of ball-milling experiments were run; one in which the grinding aid was varied, a second in which the grinding fluid was varied, and a third in which the material being ground was varied MATERIALS, APPARATUS, AND PROCEDURE In the first group of experiments in which the grinding aid was varied Inco Carbonyl Grade B nickel powder initially 2.5 (all sizes refer to average particle size as measured by Fisher Sub -sieve Sizer) was used as the material being ground and 200-proof ethyl-alcohol as the grinding fluid. Surfactants, representative of typical organic structures, were selected as grinding aids. Inorganic salts used as grinding aids were chosen on the basis of the size and valence of their ions. Water soluble salts were used in order to facilitate their removal from the slurry after grinding. In the second set of experiments, grinding of the 2.5- Ni powder was tried in four different grinding liquids; water, cyclohexane, n -heptane, and methy-lene chloride. In this study seven grinding aids selected from those tried in the first group of experiments were employed. In the third group of experiments 200-proof ethyl alcohol was again used as the grinding fluid to mill Cu, Cr, Fe, Ag, and Ni powders of various initial particle sizes' All mill charges contained 300 ml of grinding liquid and 3000 g of 1/2 in. stainless steel balls. When inorganic salts were used as the grinding aid, 70 g of salt and 210 g of metal powder were employed, and with surfactants 6 g of grinding aid and 300 g of

Jan 1, 1962

By R. G. Hawthorne

This report is concerned with fluid displacement in porous media, in those cases where viscous and gravitational forces control the displacement. Such a system would usually be found in a sand body of large physical dimensions such as an oil reservoir, although it is possible to create such a system in the laboratory. It is shown that the position of the fluid interface can be predicted by numerical calculations using a basic idea presented by Dietz. Fluid flow is considered in a vertical plane in a homogeneous, porous medium of sufficient thickness that the capillary transition zone is small in comparison with the total reservoir. A theory developed by Dietz' is used to make numerical calculations of the position of the fluid interface. The results for several conditions are compared with scaled model experiments. The results show that, for gas drive in a reservoir of steep dip, a relatively low flow rate can displace large volumes of oil before gas breakthrough. On the other hand, water injection at favorable mobility ratio and low dip may show best performance at high rates. Water tends to underride the oil and, given sufficient rime, will break through without much oil displacement. For certain conditions, which include relatively low flow rate, the interface is a straight line and its behavior is simple to calculate. At higher flow rates, the interface is unstable, and a numerical solution was programed for an automatic computer. In general, good agreement is shown between the fluid model and the computed results so long as gravitational forces have control. For a water drive at very unfavorable mobility ratio, many small water fingers appear. These viscous fingers are not controlled by the relatively small gravitational forces. When viscous fingering becomes the controlling factor, the mathematical model is oversimplified, and results do not check the fluid flow model. INTRODUCTION Present methods of reservoir analysis depend upon certain simplifying assumptions to obtain mathematical descriptions of practical use. Material-balance methods (Muskat2 or Tarner2) assume uniform fluid saturations in the entire reservoir, or in a few subdivisions of the reservoir. An unsteady-state flow calculation by West, er at considered pressure and saturation changes in flow to a well during solution gas drive, and neglected gravity effects. Results showed only a 4 per cent difference for ultimate oil recovery by the Muskat method, even though the case chosen for study was one in which unsteady-state effects should be high. The Buckley-Leverett5 method commonly assumes a one-dimensional flow system. It is applicable at high flow rates where viscous forces predominate over gravity forces. Simultaneous, parallel flow of the two fluids is assumed, and the concept of a fluid interface is not introduced. Permeabilities to each fluid for a given saturation must be known. The method is not applicable for a two-dimensional system where cross flow becomes possible. Less well known is the displacement equation derived by Dietz. This method is designed for two-dimensional flow systems and assumes a definable fluid interface within the porous medium. Dietz showed that, for a range of low flow rates, the interface would be stable. straight and at an angle of inclination which could be simply calculated. At a certain critical flow rate, the calculated interface tilt would equal the formation dip. For higher flow rates, a finger of displacing fluid would invade the displaced fluid. Dietz indicated that his method applied only to macroscopic reservoir behavior, while the Buckley-Leverett method applied to the small transition zone at the fluid interface. The examples worked out in this report are based on the fluid-displacement theory of Dietz. It is shown that the Dietz theory may be used to derive equations analogous to the Buckley-Leverett equations. In contrast to the Buckley-Leverett method, flow is considered in a plane rather than being limited to a line. Rather than a frontal advance, the movement of a fluid interface is followed. For flow rates substantially exceeding the critical rate and for high viscosity ratio, many fingers of invading fluid occur-—rather than the single finger assumed by Dietz. On the other hand, so long as some gravitational influence remains, the flow is not entirely parallel to the bedding planes as assumed by Buckley and Leverett; therefore, both methods fail to give an adequate descrip-

By L. Weyher, H. L. Lovell

This discussion is restricted to a very specific application of the cyclone - its use as a hydro-cyclone in the cleaning of fine coal. It is hoped that the development of the present data will assist in the further elucidation of existing qualitative models, and also in an enhanced application of the hydrocyclone and provide a base for further research. Discussed are the mechanisms of gravity separation in hydro-cyclones, test procedures, experimental observations, and industrial applications from these studies. Within the general area of unit operations, a considerable effort has been expended in theoretical and empirical research associated with cyclone operations. The motivation involves the industrial requirement for devices and techniques to manipulate small particles at low operating costs, a situation required in coal preparation. There are good reasons why the cyclone helps to satisfy this demand, because it combines operational simplicity (no moving parts) with versatility and high throughput capacity per unit area. The cyclone is one of the most widely applied tools in the process technologies. There are areas for potential cyclone application which have been only meagerly explored or not considered at all. This discussion is restricted to a very specific application of the cyclone - its use as a hydrocyclone in the cleaning of fine coal. It represents an initial presentation of a more comprehensive report. Coal preparation can appropriately claim the hydrocyclone since most of its predominant industrial uses have originated in this area and have spread into other applications, including the broad field of ore dressing, the petroleum industry, chemical processing, nuclear engineering and food technology. There is one operational principle common in all cyclones: A fluid is tangentially introduced into a cylindrical or conical container under pressure. A predominantly irrotational flow field1 is established within the cyclone (Fig. 1). The uniqueness of this flow is indicated by the variation in tangential velocity across the cyclone radius, which reaches a maximum a short distance from the center and decays toward the cyclone wall. In contrast, the tangential velocity in a centrifuge increases uniformly toward the wall. Usually two products are discharged from the cyclone. They differ in that one discharge consists predominantly of that portion of the feed fluid which moves along the wall axially away from the feed inlet, while the other consists predominantly of fluid spiralling along the central regions of the cyclone, in an axial direction opposite to that of the wall current. Fig. 2 indicates these discharge points schematically. The latter product may be termed the vortex-product, since it is discharged with the central vortex-current. In the case of conical cyclones, the former product may be referred to as the apex-product. Although the names "over- and underflow" are widely used, many cyclones are operated from extreme angular positions thus the proposed terms are less ambiguous. The cyclone feed fluid can be laden with solid particles or nonmiscible fluid drops. Such a feed component is discharged from the cyclone, after some residence time, into the one or the other product. Yet, the orifice through which a particle will leave the cyclone is dependent upon a number of factors. These factors, in a statistical sense, determine the path of the particle within the cyclone. Thus, different separation phenomena are possible and different process results attainable by the controllable variation of the particle path. It is then, to attain a fuller understanding of this particle path, to which this study is ultimately directed. It is anticipated that the detailed study of the data being developed will allow further elucidation of existing qualitative models. However, the development of a quantitative description of cyclone operation in terms of a mechanism is not currently feasible. The flow conditions in a cyclone are not fully understood even for a pure fluid, without the added complexity of the inclusion of multiple size-density particles. It is hoped that the development of the present data will also assist in an enhanced application of the hydro-cyclone and provide a base for further research. Some practical applications drawn from the data are suggested. Cyclone operations have been classified according

Jan 1, 1967

By K. K. Clark

Excessive injection pressures in water injection wells may create deeply penetrating fractures, or may open up existing reservoir fractures. If these fractures are oriented toward offset producing wells, oil recovery at injected water breakthrough and ultimate recovery will be impaired. A method of calculating fracture lengths from pressure fall-off test data is presented. The method is based on a linear flow model that simulates conditions present during the early-time period after shutting in an injection well. Fracture lengths can be calculated directly if formation permeability is known. A graphical technique is presented that provides fracture lengths based on permeabilities calculated from normal fall-off tests, where those permeabilities are adjusted for flow geometry. Test data from four injection wells and results obtained from applying the method to these wells are discussed. Introduction Rates of water injection into nonstimulated wells in low permeability reservoirs frequently fall below economically desirable levels. Therefore, some form of stimulation such as hydraulic fracturing often is performed on these wells. Usually these fractures penetrate a short distance from the well — short as compared with interwell spacing — and therefore should not create problems of water channeling to offset producing wells. In the past, some operators have been tempted to increase injection pressures continually to maintain a specified injection rate. But pressures cannot be increased indefinitely. Field data indicate that continued injection above fracture opening pressure can cause excessively long fractures to approach between well distances. If these long fractures intersect or closely approach offset producing wells, premature water breakthrough can result. It is difficult to seal effectively these fractures by various workover procedures after premature water breakthrough has occurred. This paper describes testing procedures that are potentially capable of detecting premature water breakthrough before it occurs. Knowledge of fracture lengths and fracture opening pressures can assist field engineers in selecting optimum operating conditions for water injection wells. Fracture lengths should be calculated from pressure fall-off tests on injection wells, and maximum permissible iniection pressures should be determined from step-rate injectivity tests. Equipped with this information, the field engineer is in a better position to recommend for a particular injection well the optimum operating conditions that will lessen the chances of channeling to offset producers. Historically, pressure transient tests have been conducted primarily on producing wells and analysis procedures have been based on radial flow concepts. Several authors have suggested that these same procedures be applied to tests conducted on water injection wells. This application is justified for wells that are not connected to extensive fracture systems. However, if the formation is severely fractured, the interpretation methods must be modified. Several authors have presented the pressure response of various systems that are intended to simulate reservoir conditions. A paper by Russell and Truitt* on vertically fractured svstems is probablv the most useful from the standpoint bf the fieid engineer. Russell and Truitt presented the pressure-vs-time behavior of a well connected to vertical fractures with various fixed lengths. Their permeability adjustment technique is used in this paper to refine methods of calculating fracture length and interwell permeability. Theory and Definitions Three flow-system geometries are considered in analyzing injection well test data. These various geometries are applicable during specific time intervals of transient pressure tests. Schematic drawings of the flow models, and the time intervals over which they are applicable, are shown in Fig. 1 in the chronological order that they are applied to the pressure response of water injection wells in fractured formations. The very early response is simulated by an infinite linear system as shown in Fig. 1A. This representation permits the calculation of matrix surface area exposed to the fracture. The model shown in Fig. 1B is identical with the one studied by Russell and Truitt. They evaluated the transient pressure response of this vertically fractured system by finite difference techniques. The results were presented as tabulations of dimensionless pressure drop functions for a range of fracture lengths. A semilog plot of these data shows that the apparent matrix permeability can be related to the true matrix permeability by a simple exponential function. Their adjustment factor is used in this paper to improve the accuracy of matrix-permeability and fracture-length calculations.

Jan 1, 1969

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By P. H. Wendland

Calculations are presented for the design of a silicon photodiode in which the incident light beam makes multiple passes between the detector surfaces. Total internal reflection is used for this "light-trapping" effect. By this means, the optical path length can be extended to several millimeters, while the electrode separation remains less than 102 cm, as required for nanosecond response time. Data are presented for a Schottky barrier photodiode constructed on a multiply reflecting silicon base wafer. It is shown that the long-wavelength response is considerably extended in such structures without a corresponding sacrifice in high-speed response. The development of efficient and powerful lasers at 1.06 p has stimulated interest in detectors which operate at this wavelength. In typical silicon photodiodes, for detecting 1.06 p radiation, the requirements for high speed and high sensitivity are mutually exclusive. Since the absorption coefficient is only 25 cm-', a lo-'-cm path length is required to absorb 92 pct of the incident 1.06 p radiation. If the electrode separation is greater than 10 cm, however, the carrier transit time will be greater than 1 nsec. This problem can be solved by allowing the incident light beam to make multiple passes between the electrodes. The optical path length can then be extended to several millimeters, as required for complete absorption, while the electrode separation remains less than 10' cm, as required for nanosecond response time. In a typical photodiode geometry, one ohmic contact and one rectifying contact are formed on the two opposite surfaces of a base wafer, and the wafer thickness determines the electrode separation. The objective of the multiple reflection design is to allow all 1.06 p radiation to enter the detector front surface and to form the back detector surface so that no 1.06 radiation can exit. Total internal reflection at the back detector surface is well-suited for light trapping of 1.06 p radiation because the relatively large dielectric constant of silicon leads to a critical angle of 16.5 deg for total internal reflection. LIGHT TRAPPING It is well-known that, as light passes from one medium such as air into another medium such as glass or silicon, the angle of refraction is always less than the angle of incidence. In the limiting case, where the incident rays approach an angle of 90 deg with the normal, the refracted rays approach a fixed angle +, beyond which no refraction is possible: this is called the critical angle. It follows from Snell's law that where = critical angle, n - index of refraction of air, n' - index of refraction of the medium. Applying the principle of reversibility of light rays, all internal angles of incidence greater than +, will produce total internal reflection and "light trapping". The index of refraction of silicon at 1.06 p is 3.5,' and the critical angle is thus 16.5 deg. Fig. 1 shows these relationships for silicon. This very small critical angle in silicon is significant because all incident angles between 16.5 and 90 deg will produce total internal reflection and "light trapping". This effect can be implemented with a "prismlike" geometry, so that incident light can be introduced into the sample without loss and "trapped". PHOTOSIGNALS A precise knowledge of the absorption coefficient at 1.06 in silicon is of critical importance to the design of fast and efficient silicon photodiodes for 1.06 radiation. Dash and newman2 show a value of 25 cm-l, and our measurements have corroborated this value. Assuming that the collection of photoinduced minority carriers is perfect, the quantum efficiency of a photodiode is dependent only on the absorption coefficient. It then follows from Lambert's law that where QE is the quantum efficiency in pct, a is the absorption coefficient, d is the optical path length, and the reflectivity at the surface is assumed to be completely suppressed by an optical interference layer. Fig. 2 gives the maximum quantum efficiency for 1.06p radiation of a silicon photodiode with optical path length d, using Eq. [2]. The ultimate response time of a fully depleted photodiode to an incident light pulse can be considered to be the arrival times of all photoinduced carriers at the contacts, i.e., the minority carriers at the junction interface and the majority carriers at the oppo-

Jan 1, 1968

By Dr. O’Neil Thomas J., Donald W. Gentry

"Who is the man who views the mines and promptly turns them down? Who is the one that thinks this is the short cut to renown? Who is it gives the bum advice to the innocent financier? The knowledge-feigning, theory- straining mining engineer." -Anonymous INTRODUCTION Taxes levied against mining properties and operations are a critical cost in the economic evaluation of mining investments. Indeed, taxes represent a substantial cost of doing business in the minerals industry and often have a significant impact on corporate investment decisions. A good example was the postponement of mineral development in the state of Wisconsin, primarily because of what was perceived to be excessive taxes imposed by that state. In many respects mining investments are no different from other industrial investments. Astute taxing authorities should recognize that geologic endowment is a necessary but clearly not a sufficient condition for mineral investments. The fact that a mineral deposit exists does not necessarily mean that it will ultimately be developed-a point that many taxing authorities fail to recognize. While it is true that ore deposits are not mobile in the sense that they cannot be physically moved to a district having more favorable taxes, corporate investment capital certainly is mobile and flows to ventures which maximize wealth to the firm. In short, higher taxes reduce project yields and tend to drive investment capital elsewhere. The appropriate type and level of taxation imposed upon the mining industry continues to be a very controversial and emotion-charged topic. Mining activities have been taxed at various levels over the years due to widely differing taxation philosophies. Location has also influenced taxation policies, as evidenced by the diversity of tax laws and assessment procedures applied to mineral deposits by the various states. Indeed, mineral taxation varies from state to state, from county to county, and from one mineral commodity to another. Whether or not a given tax is appropriate for a specific mineral deposit, or even an industry, is a difficult problem to assess. First, the type or kind of tax which should be imposed must be considered. Second, it is most important to define a fair and unambiguous base against which to levy the tax. Finally, one must consider the tax rate to be applied to this base. It is the combination of these two components

Jan 1, 1984

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By J. M. Goris

"Researchers at the U.S. Bureau of Mines are conducting research on cable-type ground supports to assess their material and support properties and to provide design criteria for implementing cable supports as a workable roof control system under various underground mining conditions. Much of this work involves laboratory assessment of the material and support properties of cable supports using both conventional and birdcage steel cables. Included in this assessment are single and double cables, effects of changes in embedment length on support strengths, water-cement ratios, use of breather tubes, and pumpability and water-bleeding properties of grouts.IntroductionSince cable supports were introduced in the early 1970s, considerable research has been conducted in laboratories and at mine sites to understand their behaviour. The U.S. Bureau of Mines began a laboratory evaluation project in 1985 at the Spokane Research Center (SRC) to study the behaviour of cables supports under uniaxial loads so that the effects of various cable support components, such as grout and breather tubes, could be identified. Other objectives were to compare the behaviour of various types of cables and grouts and to collect meaningful data for numerical analyses. Pull tests were conducted to determine how cables supports reacted under uniaxial loads and how they failed when ultimate loads were exceeded. Such data are essential for the development of numerical models for analyzing rock mass behaviour when the rock is supported with cables.Test ProgramBecause each cable support can be composed of either single or double cables as well as a breather tube, pull tests were designed to include a variety of samples containing these components. A series of samples containing a single conventional cable, a neat cement grout having a water-cement ratio of 0.45, and no chemical additives was selected as a standard (Table I). Then one component in the system, such as the presence of a breather tube, was changed, and results of tests compared to results obtained for the standard samples to determine what influence that component might have on the behaviour of the support system. If significant changes in test data occurred, they could be attributed to that one component. To control the quality of the samples, the physical condition of the cables and tubes were monitored closely, and compressive and tensile strengths as well as flow properties were determined for the grout used in each test series."

Jan 1, 1991

By P. G. Nahin, A. Grenall, R. S. Crog, W. C. Merrill

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By W. C. Merrill, P. G. Nahin, A. Grenall, R. S. Crog

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By H. Conrad, V. Damiano, J. Hanafee, N. Inoue

The effects of hydrostatic pressure up to 400 ksi at 25" to 300°C on the mechanical properties of three forms of commercial beryllium (hot-pressed block, extruded rod and cross-rolled sheet) were investigated. Three effects of pressure were studied: mechanical beharior under pressure, the effect of pressure-cycling, and the effect of tensile prestraining under hydrostatic pressure on the subsequent tensile properties at atmospheric pressure. For all three materials the ductility increased with pressure whereas the flow stress did not appear to be significantly influenced by pressure. An increase in the subsequent atmospheric pressure yield strength generally occurred as a result of pressure-cycling or prestraining under pressure, whereas either no change or a decrease in ductility occurred. The only exception to this was sheet material, which exhibited some improvement in ductility following a pressure-cycle treatment of 304 ksi pressure. The effects of pressure-cycling and prestraining were relatively independent of the temperature at which they were conducted. Stabilized cracks of the (0001) type were found in hot-pressed specimens and {1120) type in extruded and sheet specimens following straining under pressure. Also, pyramidal slip with a vector out of the basal plane, presumably c + a, was identified by electron transmission microscopy for extruded rod and for sheet strained under pressure. Small loops similar to those previously reported were found after straining at pressures of the order of 300 ksi. THE use of beryllium in structures is limited because of its poor ductility under certain conditions. Therefore, one objective of the present research was to determine if the ductility of beryllium at atmospheric pressure could be improved by prior pressure-cycling or prestraining under hydrostatic pressure. Another objective was to study the mechanisms associated with the plastic flow and fracture of the polycrystalline form of this metal with pressure as an additional variable. Since the early work of Bridgman,1 it has been recognized that many materials which are brittle at atmospheric pressure exhibit appreciable ductility when strained under high hydrostatic pressure. This effect has been reported for beryllium by Stack and Bob-rowsky2 and by Carpentier et al.3 and has been attributed to the operation of pyramidal slip systems with slip vectors inclined to the basal plane while cleavage or fracture is suppressed.4 That such slip may occur simply by the application of pressure alone without external straining (pressure-cycling) is suggested by the results on polycrystalline zinc5 and polycrystalline beryllium,6 where nonbasal dislocations with a vector (1123) were reported. A significant improvement in the ductility of the bee metal chromium by pressure-cycling has been reported.7 On the other hand, limited studies on the pressure-cycling of the hcp metals zinc67819 and beryllium6 indicated no improvement in ductility; there only occurred an increase in the yield and ultimate strengths. The study on beryllium was limited to hot-pressed material. Consequently, additional studies on the effects of pressure-cycling on other forms of beryllium seemed desirable, especially since for chromium some authors10 have been unable to detect any improvement in ductility while others find a large improvement.7 That the ductility of polycrystalline beryllium at atmospheric pressure might be improved by prior straining under hydrostatic pressure was suggested by the known beneficial effects of cold work on the ductile-to-brittle transition temperature in the bee metals. It was reasoned that, by straining under hydrostatic pressure, fracture would be suppressed, and during the propagation of slip from one grain to its neighbor dislocations with a vector inclined to the basal plane"-'4 would operate. Upon subsequent straining at atmospheric pressure, these dislocations with a nonbasal vector would continue to operate and thereby reduce the tendency for fracture to occur, by assisting in the propagation of slip across grain boundaries and by interacting with any cracks that may develop. It was recognized that maximum improvement in ductility would probably occur at some optimum amount of prestrain under hydrostatic pressure. If the pre-strain was too small, an insufficient number of dislocations with a nonbasal vector would be activated; if it was too large, internal stresses (work hardening) might increase the flow stress more than the fracture stress, or incipient cracks or other damage could develop. EXPERIMENTAL PROCEDURE 1) Materials and Specimen Preparation. The materials employed in this investigation consisted of hot-pressed block (General Astrometals, CR grade), extruded rod (General Astrometals, GB-2 grade with a reduction ratio of 8:1), and cross-rolled sheet (Brush S200, 0.065 in. thick). The analyses of these materials and mechanical properties at room temperature and atmospheric pressure are given in Table I. The grain size of the hot-pressed block was 15 to 16 µ, that of the extruded rod 10 to 11 µ, and that of the sheet 7 to 10 µ in the rolling plane and 5 to 6 µ in the thickness, all determined by the linear intercept method. Al-

Jan 1, 1969

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By S. Luszcz, R. W. Vook, Fred Witt

In situ X-ray investigations were made on polycrys-talline silver films deposited by vacuum evaporation on (111) CaF2 and (100) NaCl single-crystal substrates at 80°K. The films were evaporated and annealed in an X-ray diffractometer attachment having a residual gas pressure of 2 x lo-' Torr. All measurements were made without exposing the films to the atmosphere. Measurements were made on the films in the as-deposited state and after various annealing treatments. The intrinsic stacking and twin fault densities, the magnitudes of the uniform and nonuniform strains, and the crystallite sizes were determined. In addition the textures in the films were measured qualitatively. The results obtained for the as-deposited films on single-crystal substrates are in substantial agreement with previously reported results for silver films deposited on glass. Intrinsic stacking and twin faults, as well as uniform and nonuniform strains, were present in these films. During the various annealing treatments (up to 350°C) the faults and nonuniform strains annealed out. Considerable grain growth and texture changes occurred also. The effects were much greater for the NaCl substrate than for the CaFz substrate. The relative magnitudes of the grain growth in the variously oriented grains could be explained qualitatively in terms of the thermal strains and strain energies introduced into the differently oriented grains during the initial, irreversible anneal. These strains were due to the different thermal expansion coefficients of the film and substrate. X-RAY diffraction measurements on evaporated films deposited on substrates at low temperature have the advantage that many of the imperfections introduced into the film during deposition are "frozen in". Thus, the influence of a very important experimental variable, substrate temperature, on the imperfection structure of evaporated metal films may be studied. Moreover, the effects of annealing such films makes possible the study of thermally activated recovery processes in these films. The present study was designed to determine the influence of single-crystal substrates on the resultant film structure relative to the previous results obtained using glass substrates.' To this end great care was taken to keep the experimental variables the same in the two cases. Different experimental conditions would, of course, result in films having different physical properties. Again the initial substrate temperature was in the neighborhood of 80°K and the films were subsequently annealed to 350°C. The pure metal silver was chosen for evaporation, primarily because of its relatively low stacking fault energy and consequent high fault density in the as-deposited state. The silver films were formed by evaporation onto air-cleaved {ill} CaF, and (100) NaCl surfaces cooled to 80°K in an X-ray diffractometer attachment2 having a base residual gas pressure of 2 X l0-' Torr. The films were not exposed to the atmosphere until all of the X-ray data had been recorded. In this way one of the most important experimental variables, environment, could be well-controlled and reproduced. X-ray measurements were made at the temperature of deposition and included determinations of the diffraction line peak positions, line shapes, and integrated intensities. The peak position measurements were used to determine the intrinsic stacking fault densities and the average uniform strain in the film. The shapes of the diffraction lines provided information on the twin fault density, true crystallite size, and average nonuniform strain. The preferred orientation in the film was determined qualitatively from the integrated intensities. I) EXPERIMENTAL PROCEDURE The evaporator attachmentZ was charged with 99.999 pct Ag pellets positioned in a tantalum filament which had been outgassed previously at l0-8 Torr. The CaFz and NaCl single crystals were cleaved in air and then placed in position in the chamber so that their cleavage surfaces were on the diffractometer axis. The chamber was prepumped using a sorption pump, sealed off, and then baked at 150°C for 24 hr. The ion pump operated during the bakeout cycle. The substrate was then heated to 500° C by means of an auxiliary heater and kept hot until the rest of the chamber was cooled slowly to room temperature. This bakeout procedure consistently resulted in an ultimate pressure in the low lo-' Torr range. The substrate was then cooled down on 80°K. Its temperature was monitored by a thermocouple wedged into the rear of the copper substrate holder. The diffracted intensity and peak position of the 111, 222, and 333 CaF, lines were measured prior to evaporation. Nickel-filtered, pulse-height-discriminated copper radiation was used. Similar measurements were made for the 200 and 400 lines from NaC1. These measurements were used as a lattice parameter check and to determine the thickness of the evaporated silver films from the attenuation of the substrate lines. The evaporation rates were approximately 3A per sec for both films while the maximum pressures during evaporation were 3 x lo- ' and 7 x 10"8 Torr for the CaF, and NaCl cases, respectively. The film thickness was measured by the attenuation of the CaF, and NaCl substrate lines and by at optical interference method. Values of 1700 and 1500A, respectively, were obtained for the silver

Jan 1, 1969

By C. R. Barker, D. A. Summers, H. D. Keith

Introduction Historically, the presence of methane has been a problem, mainly in and around the working areas of active coal mines, and only in these areas has drainage been considered. Drainage, where practical, has been achieved through the drilling of holes forward into the coal and the surrounding strata from the working area. These holes generaly have been short in length, although where methane drainage operations around a longwall face have been undertaken, the holes have had to be longer in order to adequately drain from the center of the face into the access gate roads. In recent years, attempts have been made to degasify the coal seams in advance of mining, without disruption of the mining cycle. This is done by drilling much longer horizontal holes through the coal in advance of the working area. Under the aegis of the federal government, methods have also been developed for draining coal seams of their methane content in advance of mining, but from shafts sunk from the surface, without using the active area of the mine as the location for the drill holes. Development of methane drainage has recently been encouraged by the potential use of the drained methane as a commercial energy source, with a need, therefore, to adequately organize a collection system, separate from mining the seam for coal. This has already been successfully accomplished, for example, in the Federal No. 2 mine of Eastern Associated Coal Corp. starting in 1975 (Johns). However, whether the system gains access to the coal through horizontal drilling from a pre- existing mine or via access through a separate shaft from the surface, long horizontal holes are required to adequately tap the methane reserve. It is to this regard-the actual drilling of the horizontal holes-that this paper is directed. It will examine potential benefits that may accrue, both in conventional horizontal hole drilling from a mine site underground, and also in drilling from the surface if a high pressure water jet drill is used to drill the degasification holes. Long Hole Drilling from an Underground Site Personnel from the Bureau of Mines have recently examined methods for conventional drilling of long horizontal holes to gain access for methane drainage. They have shown that it is possible (Cervik, Fields, and Aul) to drill out some 610 m using a conventional drilling system. Three types of bit were used in the program and by alternating between a drag bit, tricone bit, and plug bit, advance rates of between 0.6-3.6 m/min were achieved. Hole diameters varied from 7.6-9.2 cm in surface tests at bit thrusts of 1360 kg. A hole was then drilled and maintained in relative alignment within the coal seam for a distance of 640 m. Thrust levels had to be lowered to between 363-680 kg across the bit. Because the loads were smaller than those used in the surface trial, advance rates in the hole were of the order of 10-38 cm/min. The thrust level was lowered since it was found that the level of the thrust controlled the inclination of the drill so that, for example, a thrust of 363 kg caused the hole to incline downward, while at greater than 544 kg the hole inclined upward with the 9-cm-diam bit. Thrust levels increased 227 kg when the hole diameter was raised to 9.2 cm, although in such a case penetration rates in excess of 56 cm/min could be achieved. Horizontal Water Jet Drilling of Coal The University of Missouri-Rolla has recently undertaken research for Sandia Laboratories on the use of high pressure water jets as a means of drilling through coal. The initial experiment in this program called for drilling a hole horizontally into a coal seam from the side of a strip pit using water jets as the cutting mechanism. A very simple setup [(Fig. 1)] was used in this program and a 15-m hole was drilled at an approximate drilling speed of 1.2 m/min. The nozzle was designed so that the hole dimension was approximately 15 cm across [(Fig 2)] and the thrust was maintained at levels below 91 kg in moving the drill into the coal face. The system used was very crude and comprised a high pressure water jet drill enclosed within a 5.7-cm outer diameter galvanized water pipe to provide rigidity to the drilling system. This pipe sufficed to maintain hole alignment over the 15-m increment. While it is premature to make long-term predictions on ultimate applicability of this sytem to long hole drilling, certain inherent advantages of water jets can be delineated from research results and suggest considerable advantage to further research in development of this application. High pressure water was supplied at approximately 62 046 kPa from a 112-kW high pressure pump, with a 83 L/m flow through the supply line to the nozzle. The drilling system consisted of a nozzle rigidly attached to the front end of the galvanized piping. High pressure fluid was supplied to this nozzle through a flexible high pressure hose that fed from the nozzle back through the galvanized pipe to a rotary coupling attached

Jan 1, 1981

By Shiro Ban-ya, John Chipman

Equilibrium in the reaction was investigated at temperatures of 1500°, 1550°, and 1600°C for sulfur concentrations up to 7.2 wt pct. Multisample crucibles contained the liquid alloys in a resistance-heated furnace using a technique especially designed for the study of more complex alloys to be reported separately. Modern free-energy data are used to correct the H2S:H2 ratio for dissociation of H2S and calculalion of the partial pressure of S2. Published data on the equilibrium are similarly corrected. Thermodynanzic treatment of the data employs the composition variable zs = nS/(nFe — nS) and the activity coefficient Gs = as/zs The data at 1500" and 1550°C are fitted by the equation log s = —2.30zs. Within the limits of experimental error the same coefficient is applicable to the data at higher temperatures. Equations are given for the free-energy change in Reaction [I] as well as for the solution of S, gas in the metal. The heat of solution of 1/2 s2 is -32.28 i2.5 kcal. Uncertainty in the free energy is very much smaller. For dilute solutions of interest in steelmaking, the activity coefficient of sulfur is unchanged from that listed in Basic Open Hearth Steel-making. DETERMINATIONS of the thermodynamic properties of sulfur in liquid iron by Morris and williams1 and by Sherman, Elvander, and chipman' provided a basis for control of sulfur in steelmaking processes. From the standpoint of understanding the chemistry of metal plus nonmetal in liquid solution they left several questions unanswered. The activity of sulfur in dilute solution at about 1600°C was well-established but temperature coefficients were uncertain, due at least in part to the use of the optical pyrometer and uncertainty regarding the effect of sulfur on emissivity. It appeared that deviation from Henry's law increased with increasing temperature, a most unusual behavior requiring either confirmation or disproof. These studies were based on experimental determination of equilibrium in the reaction: At high temperatures H2S is partially dissociated so that the gas mixture contains HS, S2, and S in addition to HS. At the time of the earlier studies the free energies of these constituents were unknown and it was therefore impossible to make adequate correction for dissociation. Observations on the effects of alloying elements by Morris and coworkers1, 3 and by Sherman and Chip-man4 enable us to assess the effects of alloying elements on the activity and to make corrections for incidental impurities in the binary liquid. These studies as well as a number of more recent investigations will be reviewed in detail after out own experimental results have been presented. It was our purpose in planning this study to avoid uncertainties regarding the emissivity of alloys and the errors of thermal diffusion which plagued some of the early attempts,5 by using a resistance furnace and thermocouple in preference to induction heating and optical pyrometer. Modern data on free energies of the gaseous species are to be applied to our data and to those of other investigators to obtain corrected values of K1 and of the activity coefficient and ultimately to relate the sulfur content of the bath to the equilibrium partial pressure of S,. Extension of the study to include ternary and complex solutions will be described in a later section. EXPERIMENTAL METHOD a) Preparation and Calibration of H2-H2s Gas Mixture. The source of hydrogen sulfide was a preparer mixture of 43 pct H2S, balance hydrogen, contained in a large aluminum cylinder. This was passed through anhydrone and through a microflowmeter. Hydrogen was passed through platinized asbestos, ascar-ite, and anhydrone, and through a capillary flowmeter. Argon was passed through copper wool at 500°C, then through ascarite, anhydrone, and a flowmeter. The flow rate of hydrogen was kept constant at 200 ml per min, to which an arbitrary amount of the hydrogen-hydrogen sulfide mixture was constantly added and then the prepared gas mixture was introduced into the reaction tube through a gas mixer. In certain experiments 200 ml per min of argon was added to the hydrogen-hydrogen sulfide gas mixture to increase the total flow rate of gas. The ratio of hydrogen-hydrogen sulfide in the inlet gas was checked for each run by chemical analysis. A sample of the gas taken from a bypass was bubbled through zinc and cadmium acetate solution (4 pct zinc acetate, 1 pct cadmium acetate, and 1 pct acetic acid) to remove hydrogen sulfide from the gas mixture, and the flow rate of the remaining hydrogen was measured by a soap bubble method to determine the volume of hydrogen. The amount of hydrogen sulfide absorbed in solution was determined by titration with iodine against sodium thiosulfate, with starch used as the indicator. The ratio of hydrogen sulfide to hydrogen in the inlet gas could be kept within ±2 pct in the range from 10-2 to 5 x 10"4 which corresponds to from 0.2 to 7.0 wt pct sulfur in liquid iron. b) Furnace Arrangement. Fig. 1 shows the furnace arrangement and the shape of the alumina crucible used in this experiment. A vertical-tube silicon carbide electric resistance furnace contained the reaction tube which consisted of two parts, the gas-tight

Jan 1, 1969