Search Documents

By R. V. Higgins

The, large volumes of low A. P. I. gravity oil that will remain in many shallow fields of California when such oils no longer can be recovered profitably by pumping are important potential sources of oil when ways and means are found to remove them from the reservoir sands. Estimated ultimate oil recoveries in many of the "low-gravity fields" of the San Joaquin Valley in California indicate that less than 25 percent (on the average) of the original oil will be recovered. These oils have viscosities of 1,000 or more centipoises at reservoir temperatures and, because of their high viscosity and low intensity of the reservoir pressure, the quantities that will be retained in the sands ultimately are so large and their recovery is such a challenge to petroleum engineers that the Bureau of Mines has made the study of their possible recovery one of its major projects. The fact that a slight increase of temperature materially reduces the viscosity of low A. P. I. gravity oils has 'prompted the use of various means for increasing the temperature of the oil in the reservoir sands and hence the rate of flow and Completeness of recovery of the oil. Hot oil, hot water, heated air, and natural gas, steam, super-heated steam, and the products of combustion have been circulated in wells to raise the temperature of the oil it the sands; electric heaters have been installed in wells, and butane and air have been intermittently exploded and the flames propagated through the tubing to the "pay" zones. None of the methods, however, have been entirely satisfactory for the recovery of large quantities of oil.

Jan 1, 1949

By R. E. Krauss

The McLaughlin Mine is a world class epithermal gold deposit located in the coastal thrust fault of Northern California, U.S.A. Homestake adopted a proactive strategy in the permitting of the Mine. Extensive environmental base line studies were undertaken. Engineering and process alternatives were evaluated for environmental impact along with other factors. A unique pressure oxidation process was selected. Screening studies were conducted as a basis for the selection of waste rock and tailings disposal sites. Project engineering and permitting were fast tracked. Construction required eighteen months and the first gold bar was poured in Parch of 1985, six years after the initial discovery. Project facilities are designed and operated so as to minimize environmental impacts. A comprehensive monitering program demonstrates permit compliance. Reclamation of the site is ongoing throughout the Mine?s twenty year life. Non-mined lands are managed to maximize wildlife habitat value.

Jan 1, 1990

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By Hairong Zeng, Matthew Baumann, Shahram Tafazoli, Edmond Chow

Measurement of rock fragmentation has evolved from a completely subjective and manual process to a statistically objective and semi-automated process. However, ultimately, the vision is to achieve a statistically representative and fully-automated process. From the blast optimization perspective, it is critical to receive reliable rock fragmentation results quickly to incorporate into the planning of subsequent blasts. Since manual rock fragmentation measurement methods tend to be time consuming, a fully-automated method is the practical way to meet these requirements.

Jan 1, 2012

By W. R. Crane

Mining of the red iron ores of the Birmingham district, Alabama, has _gone on energetically for the past 50 years and has created a large iron and steel manufacturing center, the only important one in the South. The district produces about 10 per cent of all the iron ore mined in the United States and 80 per cent of the Alabama output is red ore ; moreover 43 of the 419 blast furnaces of the country are in the district tributary to Birmingham and produce 7 per cent of the pig-iron output. The rapid growth of the district has been made possible by investigations that have led to radical changes in furnace practice; studies of methods by which the low-grade, highsilica ores may be treated by concentration 1 will give still greater impetus to development. The· mode of occurrence of the ore has made mining practice comparatively simple, but with the rapid extension of the workings underground and the disturbed condition of the ore bed some distance from the outcrop, conditions tend to become more difficult. Stoping, handling, support, drainage, and ventilation are all affected, sometimes favorably and sometimes adversely, by the extended workings and increased depth of cover. Should beneficiatioil make available the high-silica ores of the lower bench of the Big Seam, mining practice must necessarily be adapted to the new conditions and will be rendered more difficult as the weight of cover increases at long distances from the outcrop. The support of workings will require more attention as the weight of cover increases, and the efficient and economical operation of the mines will depend largely upon improvements in mining and handling the ore.

Jan 1, 1927

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

By C. H. Elder

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand-stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022

By K. KAKLIS, O. SAUBI, Z. Agioutantis, R. JAMISOLA

Machine learning in the form of artificial neural networks was applied to investigate whether specimen load evolution can be predicted as a function of acoustic emission (AE) signals in the case of three-point bending (TPB) marble specimens instrumented with piezoelectric sensors. The ultimate objective of this study is to develop a model that can quantify rock behavior under loading that can lead to rock-failure prediction in underground structures subjected to bending, such as roof failure in development or production openings.

Nov 1, 2022

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By S Hanrahan, S McLaughlin

A case study is presented that details the safety journey at a North American project involving two major contracts: a 1000 m shaft recovery and rehabilitation, and the development of a drainage gallery in a large open pit operation. In the early stages of the contracts, there were a number of incidents that created tension between the owner and contractor, which resulted in the contractor being placed on a final warning with almost imminent potential termination. As a result of this, it was agreed to initiate a focused safety recovery plan as a ‘last chance’.Over a period of two years, the engagement and consequent performance of the contractor was turned around, steadily working to set it up for success such that in one of the contract work areas, a record of ‘one year LTI (lost time injury) free’ was achieved. The journey involved the owner and the contractor teams working cohesively to educate all parties in the safety requirements and, most importantly, providing the context and understanding for certain requirements being put in place. Early on in the process, it was recognised that the owner team unknowingly was an impediment in that they did not fully understand the safety requirements and so was not able to lead the way for the contractor effectively. The journey to rectify the situation was supported and followed up by focused engagement with the project team, which generated a progressive improvement in a very challenging environment.In particular, the contractor turnaround was significant and of enough value for the contractor to ultimately export some of the safety systems from this site to other contract sites. This demonstrated the ultimate benefit of the contractor understanding and buying into a safety culture and system.CITATION:Hanrahan, S and McLaughlin, S, 2016. Winning the safety battle, in Proceedings International Mine Management Conference, pp 181-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By J. L. Eakin

The works and opinions of experts on well stimulation and related problems are summarized in this paper. The material is devoted to stimulative work in petroleum and natural-gas wells exclusive of the generally applied pressure maintenance and secondary-recovery methods. Its purpose is to review a collection of recent and available material on well-stimulation methods and techniques. Each separate discussion is accompanied by a selected bibliography. An author index is included.

Jan 1, 1964

By Leon Borgman, Michael P. Lipkewich

Orebodies at or near the surface are generally amenable to open pit mining. The development of a mining program involves designing an ultimate pit and a production schedule. This pit maximizes total profit while the production schedule maximize6 the present value of the property. Optimum pit limits can be approximated by two-and three-dimensional numerical techniques. These techniques presuppose that the mineralized area has been sufficiently sampled to allow a reasonably accurate prediction of grade at any spatial location.

Jan 1, 1969

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Jeffery L. Kohler

The research and development of a pattern recognition system which can predict incipient failures and safety hazards in the mine power network is described. An examination of mine electrical safety hazards revealed they are often related to the electrical equipment down-time experienced on mine sections. Based on this, a method is proposed that can improve both production and safety, without compromising either. Equipment failure modes are examined to illustrate how the ultimate failure can be predicted for enough in advance to allow a convenient and safe repair, followed by a discussion of actual monitoring system performance. Finally, the paper is concluded by projections of the system's utility to industry.

Jan 1, 1977

By Bolmerm R. L.

This information circular describes the application of modern methods and equipment in sinking a vertical, 916-foot-deep by 16-foot-diameter, concrete-lined access shaft for the Harold D. Roberts tunnel near Montezuma, Colo. Although the access shaft was merely a construction facility to expedite completion of a 23-mile water-diversion tunnel, a circular shaft of this type would be equally adaptable for mine development or other purposes. Comparable sinking methods and equipment could be used for similar shafts within a wide range of sizes and depths. SUMMARY In addition to excavation and support of the basic access shaft to tunnel grade, the overall sinking project involved initial preparation of a surface site and plant, subsequent construction of a tunnel-level station and loading pocket at the shaft bottom, and ultimate conversion of the basic shaft into a hoisting and access facility for tunnel operations. The sinking period for the basic shaft approximated one year. Actual tunnel operations through the converted shaft began on April 3, 1958, approximately 19 months after the project was initiated.

Jan 1, 1961

By Jr NeSmith

"Augered-cast-in-place (ACIP) pile installation technology has matured extensively since the first auger, pressure grouted pile was patented in 1959. The current technology allows for successful pile installation across a variety of stratigraphies to meet various project load resistance requirements. This paper presents an overview of current ACIP techniques by comparing a number of case histories in a variety of geologic settings from Eastern Pennsylvania, New York City and New Jersey to demonstrate ACIP pile constructability in soft soils as well as the penetration, and resulting significant loads resisted, of ACIP piles in dense soils and intermediate geo-materials. Geologic settings that will be discussed include the Piedmont and Coastal Plain geologic provinces as well as glacial till deposits. Keywords: Deep Foundations, Piles, Augercast, Augered-cast-in-place, Auger pressure grouted, ACIP, APGINTRODUCTIONThe author, along with two colleagues, published an article in Deep Foundations magazine (NeSmith et al, 2013) which described a number of the advances in equipment, techniques, installation monitoring and post-construction testing that have expanded the geologies in which Augered Cast-in-place (ACIP) piles are installed as well as increasing their efficiency in some traditional ACIP pile geologies. The author uses the term efficiency to refer to the load resisted by a pile of a certain diameter and the increased efficiency noted refers to increased allowable loads over those traditionally resisted by piles of certain diameter (or a reduction in pile diameter from that which was traditionally used to support a certain design load). The performance and installation of ACIP piles in a variety of geologies in the Northeastern U.S. are discussed herein.PIEDMONT PHYSIGRAPHIC PROVINCEThe Piedmont physiographic province stretches from Alabama to the east through Georgia and up the east coast, just west of the Coastal Plain to Pennsylvania and New York (Brown, 2002). It generally consists of soils weathered in place from the underlying bedrock, which is typically a combination of granite, schist and gneiss depending on the location within the province. The author’s experience in the Northeastern US has been on sites where alluvial or coastal plain soils overly the residual soils and partially weathered or intact rock of the Piedmont. The example presented here, from a site on Walnut St in Philadelphia PA, is representative of these projects."

Jan 1, 2016

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019