Search Documents

By C G. Sweeney

The underground mining industry is seeing unprecedented shortages in skilled labour. Migration to Australia being at an all-time low is a leading concern, with pandemic-induced border closures and lockdowns only exacerbating the skills shortage, not causing it. The skills shortage is forecast to peak in 2023 and remain high beyond 2025. With this skills shortage in mind, mining companies throughout Australia are trying to deal with stricter protocols around Health and Safety (H&S) legislation, as well as more stringent controls on quality assurance, particularly as underground mines are reaching greater depths and extending into ‘unchartered territory’. The cumulation of this is proving to be a major hurdle in ‘effective’ operational geotechnical management. The drive for automation in mining is bringing another level of complexity. However, ‘once automation is up and running, it presents the opportunity to access talent pools that may not normally be available. There is also a change in skillset that will be required to drive automation. ‘The top two emerging roles that will be critical for the future of the mining industry are artificial intelligence and machine learning (AI/ML) specialists, and process-automation specialists’ (Writer, 2021). If anything positive has come from the pandemic, it has shown that remote working can be effective and that the drive for automation and critical evaluation of skills required on-site should be given greater priority. UQ acknowledges that the industry is changing, and that digital technology is required to be offered in mining related disciplines. Industry and academia need to do more to promote geotechnical engineering in mining and balance the curriculum to suit the future of mining and make it more enticing. The average cost of a geotechnical failure is about $5 million in coalmines and can be into the hundreds of millions of dollars if production is affected (Cartledge Mining and Geotechnics, 2020). The cost of a good geotechnical design far outweighs the potential losses if a failure were to occur. This alludes to the growing importance of experienced geotechnical consultancies playing a pivotal role in managing mine site geotechnical hazards, while the industry is developing the next generation of geotechnical engineers.

Nov 29, 2022

By Ashirbad Satapathy, Sanket Rawat, Ramanand Shukla, Ravi Kant Mittal

Bearing capacity factor (Nq) and Adhesion factor (α) are the key parameters for analyzing the load carrying capacity of pile foundations embedded in cohesionless and cohesive soils respectively. Numerous models are available in the form of charts or equations for the computation of these parameters and hence, have been adopted by most of the International and National standards. Indian Standard for the Design and Construction of Concrete Pile Foundations, IS 2911–Part 1 (2010), also makes use of charts detailed in its Annexure B. However, the sources of these charts have not been specified clearly, making it difficult to back-refer to the actual models to assess their basis for resolving any critical scenarios encountered during design. The present study aims at acquiring a distinct understanding of the development of these charts in order to bring more clarity to the design process of pile foundations. The given charts have been compared with various models specified in existing literature and international standards for the calculation of Nq and α for both driven and bored piles and hence, the basis of Indian Standard charts has been identified. Moreover, it is evident that the use of these charts complicates the process of automation of analysis and design of pile foundations as well as the associated optimization studies. Additionally, the manual entry of data especially, from the logarithmic graph of Nq, escalates the chances of error thus, making it a critical concern for design offices. Therefore, this paper also presents a non-linear regression model for Nq and α, developed using NCSS software for both driven and bored piles. Through multiple iterations, the value of coefficient of determination for Nq and α has been found to reach greater than 0.995. The developed equations can be simplistically used for both manual and automated analysis of pile foundations.

Nov 1, 2022

By Jeffrey W. Lin, Larry B. Weston, Jonathan D. Abbott, Jordan L. Arthur

Hydrocarbon fuel oils are one of the main components of ammonium nitrate-based explosives, including ANFO (Ammonium Nitrate-Fuel Oil) and emulsions. While a wide variety of fuels can, and have, been used in the manufacture of ANFO and emulsion products, No. 2 diesel, particularly dyed, off-road diesel, is widely used due to its ready availability and use in fueling mining equipment. However, a number of alternatives to standard diesel have been introduced over recent years, namely, biofuels, ‘high-performance’ diesels, and renewable diesels. The pressure to adopt these alternative fuels come from a variety of sources, such as initiatives to reduce carbon footprints, increased lifetime of equipment, and cost-advantages from tax credits. While these factors may provide a very real benefit to the mine site, a consideration that is often missed is how the use of these fuels can impact the formulation and characteristics of the ammonium nitrate-based explosives. Herein will be presented a discussion of these alternative fuels from a chemical perspective as well as the results of several studies focused on how the inclusion of various alternative diesels influences the production and performance of ammonium nitrate explosives. ANFO and emulsion were manufactured using representative fuel sources and studying in terms of the manufacturing parameters, shelf-life, interaction with other chemicals using in mining explosives. Detonation data was then collected for these products and compared to the behavior of products made with standard diesel fuels.

Jan 21, 2025

By T. C. WEBB

In New Brunswick, significant potash deposits are intimately associated with rocks of the Lower Carboniferous Windsor Group. To date, two deposits high in sylvinite, up to 20 m thick, have been confirmed at depths between 490 and 1,035 m below surface near Plumweseep and Salt Springs. These areas are currently under development by the Potash Company of America and the Denison-Potacan Potash Company respectively. A third area, near Lower Millstream, is also known to contain potash-bearing evaporites and is now being explored by BP Exploration Canada Ltd. All three areas are situated in the western half of the Moncion Subbasin and are within 25 km of Sussex. Numerous similarities in stratigraphy, thickness, mineralogy and structure suggest that deposition of evaporites throughout much of southern New Brunswick was contemporaneous and extended over a considerable area. Future opportunities for potash exploration in the province thus seem excellent. A number of large unexplored areas remain in the Moncion and Cumberland Subbasins and in parts

Jan 1, 1984

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By Ellis S. Hertzog

The data published in this report cover only one phase of a special study of the physical and chemical properties of Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, end ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This paper makes available for the first tine fairly comprehensive information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors have included a complete description of it in this report.

Jan 1, 1938

The OK orebody comprises a steep dipping narrow quartz reef averaging 0.4 m in width hosted in basalt and gabbro with porphyry bars cross-cutting through it. The following paper tracks the mining of this orebody, challenges encountered, measures undertaken to address these challenges and changes in mining conditions and methods as the mine matured in both depth and age. The initial mining method was narrow vein hand held shrink stoping accessed by shaft, that over the period of the mines life was superseded by gallery stoping, shrink stoping and ultimately mechanised narrow vein long hole sublevel open stoping. The reasoning behind the change in mining methods is detailed, including safety and cost benefits. The transition presented many challenges that were overcome, resulting in the successful development of a narrow vein long hole stoping method. The lessons learnt during the transition period and the practices and principles developed for successful mining of narrow vein orebodies using long-hole open stoping methods are summarised in this paper. The final section of the paper takes a retrospective view of how the knowledge gained through the mining of the OK orebody would be applied to a new mine containing an orebody of this type, with consideration given to the initial excavation design, equipment selection, mining sequence, geotechnical investigations and mining method used.

Jan 1, 1998

By R. W. Boyle

"EDITOR'S NOTEPart 1 of this paper, published in the August issue, covered lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos.Part 2, which follows, continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, and geothermometric, geobarometric, thermoluminiscent, pedochemical, hydro-chemical, atmochemical and biogeochemical methods. It concludes with a selected bibliography.Surveys Utilizing Leakage HalosLeakage halos can be used as scalar or vector quantities in thesearch for deeply buried blind mineral deposits. In the first case, the occurrence of a leakage halo (e.g. a small pitchblende seam) may simply indicate the possible presence of pitchblende mineralization or orebodies; in the second case, the areal or three-dimensional distribution of leakage halos may, by their increasing frequency and I or increasing metallic or gangue element content, provide a means of vectoring in on loci of mineralization and orebodies. Examples of both cases are given in the following text.Leakage halos are of many types, as shown in Figure 2 (Part 1), and are best discussed with respect to their associated mineral deposits. Furthermore, it should be noted that leakage halos are frequently offshoots or extensions of enveloping halos. Where this occurs, careful tracing of the leakage halo(s) downward or upward respectively will often lead to the apex or nadir (bottom) of the enveloping halo(s) and ultimately to mineralization or ore."

Jan 1, 1982

By R. H. Fett

T HE APPROACH to maintenance must always be ?completely positive: there must be no question of putting off difficult problems until it is more convenient to tackle them. By this it is meant that a piece of machinery or equipment which, by experience, is known to be due for a check should not, merely because it appears to be operating satisfactorily, be left until it reaches a critical .condition and breaks down. The mentality of the Maintenance Manager must be completely orderly and methodical and he should, in fact, possess a ledger-book mind, having a debit and credit outlook. The debit side would be that applying to time out of service, cost in wages, material, personnel involved, etc., and the credit side that relating to continuous operational time of the locomotive and therefore to the ultimate benefit of the mine and the personnel who work there. The Maintenance Manager is not concerned with design problems, and although he and the personnel under his jurisdiction are not engaged in productive work, he and his staff do, nevertheless, add greatly to or detract from the overall efficiency of the organization. Provided the machinery placed in his care is good to start with, he must take the best steps he possibly can to keep it running. However, he may, on occasion, be forced to improvise and this is where the ingenuity of a clever man rises to the occasion.

Jan 1, 1956

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in rescent years. The tenative ball-mill grindability method D408-35T4/ was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity.

Jan 1, 1938

By W. A. Calhoun

A method for treating high-iron Arkansas bauxites for recovering both abrasive and metal-grade bauxite has been developed by the Bureau of Mines. Present practice usually produces a reject containing appreciable quantities of metal-grade bauxite; however, the processing renders the alumina in the reject unsuitable for the Bayer extraction treatment. Thus the Arkansas abrasive bauxite industry has, in the past, produced little or no metal-grade bauxite. The present investigation was made to determine the possibilities of batter utilization of those particular bauxites through recovery of the wasted metal-grade portion. The large expansion of aluminum-production facilities planned for 1951-53 makes recovery of metal-grade bauxite from presently treated abrasive and marginal abrasive ores en especially timely objective and a welcome addition to our aluminum potential. The quality of the Arkansas bauxites and the inherently associated titania content have made this material particularly attractive to the abrasives industry. however, the gradual depletion of natural abrasive-grade bauxite reserves in this area, the comparative scarcity of high-grade ore, and the difficulty of maintaining adequate reserves have necessitated blending different grades of bauxite calculated to meet specifications. Production of abrasive-grade bauxite from tile, high-iron reserves 13 becoming, increasingly necessary. In one commercial operation, producing abrasive-grade from ores averaging slightly less than 10 percent Fe2O3, approximately 2.7 tons of ore are required to produce 1 ton of abrasive-grade bauxite. The reserves of ore of this grade, however, have been considered inadequate for a long-range production, and ultimately ores averaging 12 to 15 percent Fe2O3 will have to be treated to moot the continued demands of the abrasive industry.

Jan 1, 1952

By T Elkington, A Finch

The theory of constraints (TOC) is a business improvement method that focuses on exploiting a business’s bottleneck to deliver the highest possible profit. Early applications were mostly in the manufacturing industry; however, the theory in itself is completely generic and has now been applied widely in other industries such as services, retail, software and distribution, amongst others. The intent of the approach is attractive – it focuses on the ‘silver bullet’ rather than ‘death by a hundred projects’, and it focuses on growth rather than cost cutting. Application within the mining industry has been limited to date, although there are a few applications emerging. This paper discusses how TOC can be applied to maximise value during the project planning phase and how to maximise profits when the mine is operational. The paper uses two case studies to illustrate the approach. Case study 1 uses the approach to improve tactical mine planning, which delivers an increase in revenue of 58 per cent. The second case study is a strategic mine planning example that delivers an increase in value of 77 per cent.CITATION:Finch, A and Elkington, T, 2014. Application of the theory of constraints to strategic and tactical mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By S Graskoski

The allocation of boggers and trucks at Telfer’s sublevel cave mine is currently assigned by manual techniques, with decision-making primarily dependant on the judgement of the operators and mine control. Field observations indicate that allocation decisions could be improved by establishing a systematic approach to dispatch. An investigation into the current state of technology determined that no currently available solution would provide a tool to make optimal decisions for the Telfer dispatch challenge.In an underground sublevel cave (SLC) environment, the destination decision is fixed and the source is variable, so open pit and block cave solutions are not relevant. Newcrest underwent a development venture with an external vendor to develop a novel production dispatch algorithm and user-friendly software program to make allocation decisions in a systematic way with consideration given for the true complexity of the operation.This new production software, nicknamed Dingo (for Dispatch ‘n’ Go), is a smart way to assist forepersons and mine control operators in their day-to-day roles of planning shifts and allocating trucks and loaders to optimal locations during shifts.CITATION:S Graskoski, 2017. Dingo – an optimisation tool to solve complex short interval control at Telfer underground mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 261–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J. Awmack, M. A. Tomlinson, P. J. Lind

"Peñasquito is a complex polymetallic deposit containing gold, silver, lead, zinc, and copper and is one of the largest producers of gold in Mexico. Mining activity is currently transitioning to a second open pit, Chile Colorado, which will be mined concurrently with the existing open pit, Peñasco. The ore bodies are located within diatreme pipes and into the surrounding sediment formation. In the coming years, mining will be carried out in more sedimentary zones, which are significantly higher in organic carbon content. Organic carbon in the feed influences both flotation and leaching operations. Several changes are being implemented to the Peñasquito flowsheet to mitigate the effects of increased organic carbon in the plant feed. These include the use of alternate reagent schemes, construction of a carbon pre-flotation circuit, implementation of a pre-leach flotation circuit ahead of pyrite leach, and evaluation of a tertiary process for separation of carbon and precious metal minerals.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas in the Mazapil municipality (Figure 1). Peñasquito has been in operation since 2009, with mining carried out by open-pit methods. Oxide ore has been processed in a heap leach facility and sulfide ore is treated in the sulfide processing plant. The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 465,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead in lead concentrate, and 263 million lb of contained zinc in zinc concentrate (Goldcorp Inc., 2017). To recover more of the contained gold and silver and to mitigate the impact of increasing organic carbon content in the ore, a number of significant changes are being made to the operation."

Jan 1, 2018

By K. T. Damodaran

The Chavara and Manavalakurichi placer deposits have been known since a long time for their rich reserves of heavy minerals like ilmenite, rutile, monazite etc. While detailed work has been conducted on the mineralogy and texture of the bulk placer sediments, reports on the detailed investigations on individual minerals are relatively scanty. Though, limited work pertaining to the chemistry of ilmenite has been carried out by Nair et al (1995) and Ramakrishnan et al (1997), a comprehensive study of the weathering patterns of ilmenite along the longitudinal and vertical profiles has not been, so far, undertaken. Data on the microscopic analysis of ilmenite from the southwest placers, too, is sketchy. The present work deals with the variation of the weathering undergone by ilmenite in the southwest placer deposits based on chemical and mineralogical analyses.

Jan 1, 2002

By David A. Newman

In the 1950s, an underground limestone mine in the Camp Nelson Formation was developed from an outcrop exposure. The Camp Nelson Limestone met the requirements for DOT stone and aggregate. The mine ownership changed several times, which resulted in distinct mine designs in Level 1. Based upon the production requirements and an attempt to maximize limestone recovery from a single level, a variety of pillar dimensions and three mining heights (28 feet, 68 feet and 83 feet) were developed. This was sufficient prior to reaching the mineable extent of Level 1. Level 2 introduced previously unknown ground control challenges. These included: ??Pillar spalling and a significant back fall on the Level 1 - Level 2 decline; ??Laminated immediate back and the need to bolt the back on Level 2; ??Delamination of the back adjacent to the Level 1 - Level 2 decline resulting in bolt shearing, and floor heave in isolated areas of Level 2; ??Multiple level interaction, the need to design pillars based upon numerical modeling as columnization between Levels is infeasible: and ??Water inflow as the mine approached river. To meet the challenges, a testing program to determine rock strength and physical properties was implemented along with numerical (LAMODEL and FEM) modeling, and borescope inspections of the immediate back. The efforts to implement rock mechanics were re-focused as Level 2 approached its mineable limit and the initial attempt to drive a decline to Level 3 was unsuccessful. A second decline site was selected based on inter burden stability, a consistent shale parting for the Level 3 back horizon, results from numerical models of the immediate back and multiple level interactions, and the projected low water inflow. The mine is operating on Levels 2 and 3 with long-term planning and ground monitoring for Level 3.

Jan 1, 2014

By S. Fitzel

The Betts process for electrorefining of lead has been in operation since 1902 in the Trail Operations Metallurgical complex. The Betts process allows production of high purity lead in a single electrochemical step. Process improvements and plant expansions have taken place over the many decades of operation of this process which has proven to be robust, flexible, and capable of successfully treating a large range of anode bullion compositions. This paper reviews the history of the Betts lead electrorefining process, the innovations and quick industrial adoption of new discoveries that took place at the end of the nineteenth century. The process was first implemented in Trail Operations and integrated very well with metallurgical needs then and now.

By M. C. Flemings, S. B. Brown

"Metallurgy, as all of material science and engineering, rests on the intellectual foundations of processing-structure-property-performance relationships. Today it is widely recognized that processing has been too long neglected and presents exciting opportunities for exploitation. New processes, many of them already in the laboratory, will be exploited in the year 2000 and beyond, for near net shape forming and for achieving-new metallurgical structures and composite structures. Process modelling will alter the way we think about process and product design. Processes themselves will increasingly be automated and controlled by computers, altering the nature of the workplace and the tasks of the metallurgical engineer of the future. IntroductionInnovations in metal processing is hardly a new phenomenon, with the field thousands of years old. Nonetheless, the next few decades offer particularly important opportunities to improve our ability to process these materials. We appreciate today the variety of processing paths available to us, including vapor-, plasma- and electro-deposition, multiple phase and casting technologies, and non-equilibrium processes, and how these affect structure at the atomic level and at higher levels of aggregation. We understand the basic physical mechanisms involved far better than even before and have remarkable new abilities to predict, control, and simulate the kinetics underlying processes, and the processes themselves.The following sections describe these new opportunities in greater detail. First, we examine developments in the modelling of metal processing. We then consider some implications associated with process control and automation. Finally we present what we consider to be particularly promising metal processing technologies, and conclude with a few summary comments."

Jan 1, 1988

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014