Search Documents

By Alexsandro Berger

Many thickener operations continue to be constrained by their ability to process consolidated underflows with high yield stress and associated rheological characteristics. To maximise separation efficiencies within a thickener operation the use of both engineering and reagents are always considered. BASF is developing a Novel Flocculant Technology (NFT), which combines both of these aspects to enhance the performance of the thickener operation, improving the areas of pumping efficiency, underflow density and throughput. The development progression through stages of laboratory scale batch test work to pilot scale dynamic testing has demonstrated the ability of BASF NFT to maintain effective flocculation performance whilst increasing the rate of underflow consolidation, and significantly reducing the associated underflow yield stress of the treated material. This paper will present application data through full scale dynamic testing conducted on a granite washing circuit to demonstrate the performance benefits that NFT offers to a thickener operation. Compared to the conventional flocculant treatment, within the operation parameters and conditions employed during the full scale trials, the NFT produced a reduction in underflow rheology (yield stress) of around 45 % relative to a given solids and improved the underflow consolidation by providing at least 20% relative higher underflow solids loading than the upper limit of the given typical thickener operation. Keywords: flocculation, thickener operation, rheology, yield stress, underflow density, throughput, slump test

Sep 1, 2012

By V. Yahorava

Mintek has developed a non-destructive Resin-in-Leach method for the recovery of Rare Earth Elements (REE) from phosphogypsum (PG) waste dumps. However, PG from different sources was found to be highly variable in terms of REE recovery and physical properties. Development of a pre-treatment process was initiated to improve the robustness of the current REE recovery process in order to render it effective for any type of PG. Extensive research into the mineralogy of REE associations with PG revealed that the majority of REE are trapped inside phosphogypsum clusters which inhibits their recovery. Hydrothermal treatment of PG-containing slurry was found to result in re-crystallisation of gypsum with the release of REE phases encapsulated in it. This process was tested on various PG samples and subsequent REE recoveries improved from 5 to 80%. This approach carries a large potential for unlocking value associated with gypsum dumps worldwide.

By Naj Aziz, Peter Craig

"Double shearing tests were carried out on the 28 mm (1 in) hollow strand Jennmar TG cable bolt to gain a better understanding of the shearing behavior of the cable. The first test was limited to a 50 mm (2 in) travel on the testing machine and produced a shear load of 900 kN (92 t) at the maximum 50 mm (2 in) displacement. The axial load generated on the cable bolt was 238 kN (24.3 t). In the second test, the machine travel was increased to 75 mm (3 in), and first strand failure of the cable, due to shear loading, occurred at 1,354 kN (138 t) vertical load at a vertical displacement of 59 mm (2.3 in). The cable axial load was in the order of 385 kN (39.3 t). Analysis of the failure mode and loads achieved showed that the cable strands bent and the concrete crushed along the shear plane; the shear loading across the concrete and grouted cable then reached the tensile strength of the steel wires.INTRODUCTIONCable bolts were introduced to the mining industry around 1970, initially to surface mining and underground metalliferous mining and then to coal mining in the early 1980s, mainly for roadway reinforcement as a secondary means of support. Cable bolts have since been used as both primary and secondary supports. As primary support, Fuller et al. (1994) described the application of cable bolts, known as FLEXIBOLT, for strata reinforcement in both Angus Place and Ellalong Collieries, in New South Wales (NSW), Australia. As secondary support, cable bolts have also been used as cable trusses, which act to support the immediate roof in a sling-like manner (Fabjanczyk and Tarrant, 1988; Fuller, et al., 1991; O'Grady and Fuller, 1992), and for reinforcement at higher stratification and beyond the rebar bolt length, mainly for anchoring lower strata layers immediately above the coal seam to the higher, competent bedding formation above. Initially cable bolt anchorage was by cementatious grouting and, since the 1990s, by chemical resin. The dominant type of cable bolts used for secondary support in Australian underground coal mines are 588 kN (60 t) capacity cables which are point anchored, pre-tensioned and post-grouted. Point anchored refers to a cable resin anchor. The cables are tensioned on the resin anchor; then the same cable is grouted by cementatious grout pumped to ·fin the annular gap around the cable from the collar of the hole to the resin anchor. Bulbs are located within the resin anchor section for mixing of the resin chemical components and efficient anchorage. The installation of these typically 8 m long cable bolts involves a lot of manual handling of the cables, lifting of heavy hydraulic tensioners, and exposure to resin grouts. Table 1 shows the specification of various cable bolts currently marketed and installed in Australian underground coal mines."

Jan 1, 2010

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By F Brenguier, R A. Lynch, G Olivier

The seismic velocities of intact rock are dependent on the applied stress. Unfortunately, the low susceptibility of seismic velocity to stress changes mean that changes in seismic velocity have to be measured extremely accurately to infer stress changes from them. Previously, it was thought that measurements of this accuracy could only be made with active sources or repeating earthquakes. In this paper, we show that the noise generated by mining activity can be used to construct virtual seismic signals with which we can measure changes in seismic velocity accurately enough to see the short- and long-term effects of a production blast on the surrounding medium. The time-dependent velocity variations achieved with this method show that the blast caused weakening of the rock mass for the rock within a radius of 200 m of the blast. The weakening is healed by confining stresses over a period of five days, after which permanent changes in the seismic velocity can be seen. The size and spatial distribution of the seismic velocity changes were compared to modelled changes in static volumetric stress, which supported the notion that seismic velocity changes can be used to measure the redistribution of stress after a blast. The results of this study indicate that this method can be a powerful tool to evaluate the evolution of stress in a mine at a relatively low cost as the data that it uses would normally be discarded.CITATION:Olivier, G, Lynch, R A and Brenguier, F, 2016. Measuring the redistribution of stresses resulting from new excavations with ambient seismic noise correlations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 873–878 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Karlson R, Rispin M

Chemical admixtures are not commonly included in the variety of backfill mixes used in the mining industry. This may be attributed to several reasons including, but not limited to: the perceived high added cost, 2. the lack of awareness about their proper use, and 3. the lack of knowledge about their features and benefits. In the construction industry today, however, chemical admixtures are used in the majority of the concrete produced, enabling concrete to become a more cost-effective building material. They also enable construction crews to meet demands for year-round construction, quicker completion of construction projects, and improved concrete properties. The high demand for chemical admixtures in the construction industry has led to numerous innovations in admixture technology in recent years. Some of these chemical admixtures have been found to enhance the production, transport, placement, and in situ properties of backfill mixes. Others have been found to reduce the cost of such mixes while maintaining, and in some cases improving, their physical properties. In this paper, a few of such innovative admixture technologies are discussed. The benefits, imparted by these technologies to backfill mixes as well as performance data on their use in several backfill applications at various mines, are presented.

Jan 1, 1998

By J Carrillo, A King

Gravity recoverable gold (GRG) is largely distinguished from other gold by its non-mineralised, metallic form, its high degree of liberation from the ore and its appreciable particle size. The gold mining industry has so widely accepted the use of batch centrifugal concentrators (BCC) and intensive cyanidation (IC) systems for the recovery of GRG that these may well be considered requirements of any plant processing ore containing appreciable GRG. The recovery of gold by gravity is quick, easy and cheap by comparison to alternatives. However, there are cases where attributes of the ore make recovery of gold by gravity and IC unusually challenging. This paper describes three examples where such challenges have been encountered and met, including those where the ore contains cyanide soluble base metals and where fine GRG is to be recovered from flotation concentrate.CITATION:King, A and Carrillo, J, 2018. Addressing challenging applications of intensive cyanidation in gravity gold recovery, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 283–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Thomas Fraser, J. D. Davis

"INTRODUCTION Preliminary tests of the Oyon coal constituted part of a wartime exploratory and development program in which many agencies participated. The general objective was to find new and adequate source of fuel and other raw materials for greatly expanded industry.The Oyon coal field, known for at least a hundred years to the mining people of Peru, offers a possible source of high-grade process fuel for the growing metallurgical industries of South America and the Pacific coast. Santolalla 4/ reports that low-volatile coal from this region was used in local smelting operations as early as 1850. It has been mined in very small quanti¬ties for many years and used in neighboring mining camps and villages. Small quantities are regularly used at Oroya for the manufacture of carbide, and in recent years small-scale coking operations in specially designed ovens in the region have demonstrated that these coals will make dense coke.During this long period of desultory operations many small openings have been made scattered over a wide area in this general region, indicating very extensive occurrence of the coal measures, although systematic exploration work has not been undertaken. However, current development work of the Banco Minero del Peru has opened up several substantially parallel highly inclined or vertical beds of workable thickness and has followed these deposits to sufficient lateral extent to prove fairly well the existence of substantial reserves on this property."

Mar 1, 1948

By Jack G. Hazan

The Critical Path Method is the modern scientific answer for solving the planning and scheduling problems inherent in today's complex projects. With this method, nothing is left to chance. All resources are controlled and kept to the minimum. The various phases are properly planned and strategically determined. Optimum conditions are evaluated for the most economical and fastest way to complete a definite project. The method must be fully understood and implemented with positive data and continuous feedback to obtain the best results. This paper covers the various aspects of the Critical Path Method and mentions some of its applications in the mining and metallurgical fields. T 0 progress to a higher state of human welfare necessarily involves sacrifices. The greatest sacrifice is to relinquish social freedom in favour of economic freedom. In the old days, for example, a cobbler was free to work at whatever time of the day he chose; today, he can't. He is now forced to adapt himself to environment and to work at stand-

Jan 1, 1965

By Gary Buchan

"Mine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mine operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. The acoustic emissions (AE) form of non-destructive testing has been used for decades to determine material or machine deterioration or potential failure. This paper presents the findings of research in AE with the results of laboratory bolt pull tests and comparisons to field experimentation, including AE sensors and bolt load data in an underground stone mine. The goal of the project is to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of predicting bolt failure or roof deterioration.INTRODUCTIONMine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mining operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. Typical ground control monitoring devices involve drilling into roof or rib, grouting or gluing of sensors, and dedicated cabling for data collection. One of the original goals of this research was to develop a methodology for a simple wireless device that could provide an indication or warning of potential roof bolt or roof failure. Various types of nondestructive testing (NDT) have been used for decades to determine material or machine deterioration or the potential failure of either. One type of NDT is acoustic emission (AE) monitoring, which has been studied for use in mining to predict rock bursts and mine failures since the 1940s (Obert, 1941; Obert and Duvall, 1942). The primary goal of the work was to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of evaluating bolt loading or roof deterioration in an underground stone mine. Bolt pull tests were conducted in the laboratory to establish a repeatable trend of AE activity versus bolt load. The second part of the project was to then install bolt load cells in an underground stone mine and monitor AE activity in the vicinity of mining."

Jan 1, 2018

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for over three years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace's hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1996

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By Loic Galisson

"Urban tunneling projects are usually extensively monitored. Most of the instruments used rely on benchmarks providing a sustainable datum throughout the life of the project. The monitoring program also is based on a predicted model of deformation induced by specific construction methods. Events can interfere with those assumptions and eventually alter the stability of these datum. In addition, the anticipated ground conditions and hence the theoretical deformation model often differ from reality. Satellite Radar Interferometry provides useful information to overcome the weakness of the hypothesis made before construction. It is also a powerful tool to ensure the continuity of the monitoring program throughout the life of the project, accurately describing the true effect of the project on the surrounding environment. This paper emphasizes the benefits and limitations of this technique for urban tunneling applications, illustrated by examples of major tunneling projects around the world. MONITORING URBAN TUNNEL PROJECTS Why Monitoring? Retrofitting existing tunnels or constructing new tunnels – including access and retrieval shafts, portals and cross passages – implies an alteration of the neighboring soil structure. Excavating, dewatering, grouting, loading tie backs, etc. artificially modifies the natural equilibrium of the pore-water pressure, of the water table level and of soil stability. In many cases, the effects are immediate: ground loss, deformation of utilities, settlements of buildings, and distortion of infrastructure are a few examples resulting from construction activity.Instrumentation and Monitoring Scope To control and mitigate the risks of damage associated with the above effects, tunnel projects usually include an instrumentation and monitoring program. Depending on the level of geotechnical, structural and environmental risk, the magnitude of this program varies. Projects with a low exposure to risk may restrain the program to conventional methods such as limited topographical surveys and intermittent manual readings of geotechnical instruments. On the other hand, iconic projects with high risk or with controversial history may implement complex and extensive instrumentation plans, involving highly technical solutions such as Automated Motorized Total Stations (AMTS – see opposite Picture 1), Multi-Point Borehole Extensometers (MPBX), In-Place Inclinometers (IPI) and a wide series of fully automated geotechnical, structural and environmental sensors. In this case, all the devices are usually connected to field data loggers collecting raw data around the clock at frequencies ranging from days to seconds, depending on the sensors."

Jan 1, 2016

By Jorge Sandoval

El presente texto señala un modelo conceptual genérico, cuyo uso de plataformas informáticas permite revisar la validación de la data, previa a la emisión del KPIs, de forma que genera rigurisidad y representatividad para el análisis. En ese sentido, el modelo se basa en la integración de las plataformas, reduciendo los tiempos de procesamiento de la data y eliminando sesgos por la manipulación de la misma. Asimismo, homologa y standariza los árboles de equipos, modos de falla, entre otros aspectos.

Mar 1, 2016

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017

By Kim B. Shedd, Erin A. McCullough, Donald I. Bleiwas

"The earliest known use of cobalt was to make blue glass in Mesopotamia before 2000 B.C.E. Since then, innovations across many diverse industrial sectors transformed cobalt into an essential commodity for contemporary society. The physical and chemical properties of the element cobalt and its alloys and compounds make them indispensable for a variety of applications, including aircraft engines, hybrid electric vehicles, machine tools, missile guidance systems, petroleum refining and smartphones. As a major industrialized nation, the United States is a leading consumer of cobalt and cobalt-containing products. However, with few exceptions, U.S. cobaltcontaining ore deposits are of low cobalt grade. Historically, U.S. cobalt mine and refinery output have not met domestic cobalt demand. As a result, U.S. cobalt chemical and alloy producers need to procure most of their cobalt from the international market, which can become susceptible to supply risk.The 1978 Cobalt Crisis illustrates supply risk. At that time, the Democratic Republic of the Congo (DRC) (then known as Zaire) was the world’s leading producer of mined and refined cobalt. An insurgent invasion of the country’s copper-cobalt mining region during a period of high cobalt demand and low producer inventories caused a temporary supply shortage in the international market. The monthly average cobalt spot price increased from $18/ kg ($8/lb) before the crisis to $99/kg ($45/lb) seven months later. The high price and concern about potential disruptions in supply prompted manufacturers to reduce or substitute for cobalt where possible, and encouraged increased recovery of cobalt from scrap. The DRC has regained its position as the leading producer of mined cobalt globally and continues to be characterized by high governance risks (U.S. Central Intelligence Agency, 2015; World Bank, undated). This article will present current and historical world cobalt production trends, which can help inform discussion about the variety of international supply chain risks consequential to its trade."

Jan 12, 2017

By L. Yuan, J. H. Rowland, R. A. Thomas, D. Bahrami, G. P. Cole

"The past several decades have seen a steady increase in the use of atmospheric monitoring systems (AMS) in underground mines as sensor technology has advanced and costs for this technology have decreased. The AMS is a reliable tool for early mine fire warning by detecting gaseous products of combustion in underground mines. During a mine fire emergency, mine decision makers rely heavily on the prompt and accurate knowledge of the ventilation and fire situation in the mine, such as fire location, fire size, and the spread of smoke to make effective and efficient decisions on firefighting strategies and miner evacuation. Meanwhile, a prediction of the potential for fire development at a later time, such as whether the currently designated mine escapeways will be contaminated by smoke and toxic gases with the progress of the fire, is critical for effective decision-making to save lives that are in danger. The AMS monitoring data, including carbon monoxide (CO) concentration, airflow rate, smoke, etc., can provide information as to whether the smoke has reached the locations where AMS sensors are installed and if a mine-wide smoke spread has occurred. The National Institute for Occupational Safety and Health (NIOSH) has undertaken a task to integrate real-time AMS monitoring data with the mine fire simulation program, MFIRE, to simulate and predict the spread of smoke and toxic gas in a ventilation network based on the real-time AMS data. This paper reports the developed real-time method for characterizing the size and location of an underground mine fire and for predicting the spread of contaminants throughout the mine ventilation network using sensor data from the AMS.INTRODUCTIONNIOSH conducts research to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in underground mines. The advancement of senor technology and the increasing demand for real-time mine parameters monitoring have led to extended applications of atmospheric monitoring systems (AMS) in underground mines worldwide. In the United States, AMS is primarily used for early mine fire warning by detecting carbon monoxide (CO) in fire hazard areas, such as belt entries. Mine fires can grow rapidly, and time is the critical element. Prompt detection, timely and accurate warnings to those miners potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground mine fire (Conti et al., 2005). The early detection of a mine fire could gain time for the first responders to put out the fire before it develops into a disaster. An AMS system with CO sensors has especially played an important role in the early detection of mine fires. The continuous monitoring of an underground mine atmosphere with an AMS could generate a large amount of data in a mine fire event. However, the current application of AMS is mainly limited to sending out an alarm when monitored CO concentration exceeds a certain level. An opportunity arises as to whether these data can be further used in fire emergency response. In order to make effective decisions on firefighting strategies, mine workers’ seeking refuges, evacuation and escape, and the timing on when to send rescuers, decision makers need accurate and timely knowledge of the ventilation and fire situation in the mine. Information about the fire intensity, where in the mine the smoke and toxic gases have spread, and whether designated mine escapeways have been compromised by smoke and toxic gases from the fire would greatly increase the effectiveness of these decisions. However, the monitored AMS data only provides atmospheric conditions in the vicinity of sensor locations. What is concluded from the monitored AMS data highly depends on the decision makers’ capability and experience. Predictive insight into fire growth and smoke transport would greatly help decision makers during a fire emergency."

Jan 1, 2019