Search Documents

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

By M. P. A. Hames, D. R. Beaumont

INTRODUCTION Legend has it that when Isembard Kingdom Brunel was confronted with the cost and consequences of one of his bridges having failed, he responded cheerfully that the event had saved investors and taxpayers a fortune because it prevented him from repeating the same design at several other locations. To meet the demands of rejuvenating and expanding the transportation system in an era of industrial growth Brunel and his contemporaries introduced bold designs and many innovations. Great advances in design and construction techniques resulted, yet these too had their practical limits as the story tells. In the gold mining industry today we face the same challenge of expansion, yet designers must respond mindful of economic restraints. Is innovation the answer? It has two meanings; to bring in novelties and to make changes. Distinguishing between improvement and novelties, or simply recognizing the benefits and limitations of new ideas over proven technology is part of good design. This paper will illustrate the practical aspects of selecting appropriate solutions to a design problem by examining a variety of examples common throughout the industry. Since a variety of engineering disciplines contribute to the design of a gold processing plant, and each has some old wisdom to impart or new development to boast this paper is divided into the different areas of expertise involved.

Jan 1, 1987

An Integrated Geology-Mine-Plant and Eco-Efficiency Simulator for Anglo Platinum's Evaluation and Operational Improvement Initiatives

Sep 13, 2010

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at INCO Ltd.'s J.Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be effected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high grade nickel concentrate as the residue. Sodium cyanide was added to the froth product to depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition. The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high grade nickel concentrate ( 29. 5% Ni, . 26% Cu) and copper concentrate ( <O. 5% Ni, 30% Cu) were all realized."

Jan 1, 1984

By M. William Lallman

Potash production from natural brines of the Bonneville Salt Flats has a comparatively long history dating back to the start of World War I. However, it vas sot until the late 1930&apos;s that a successful commercial potash operation was achieved by a firm known as Bonneville Ltd. While improvements in operating techniques, pond design and equipment have been incorporated as they became available it should he understood that the basic technology developed in the late 30&apos;s and early 1940&apos;s by Bonneville Ltd, for potash production has not been changed significantly. The purpose of this paper is to present a brief review of the history, geology and hydrology of the Bonneville Potash operations and discuss the cur¬rent methods employed for brine collection, solar evaporation and the recovery of potash and other brine chemicals. A detailed study of the hydrogeology of the Bonneville Salt Flats wan made by L. J. Turk,1 Ph.D. thesis for Stanford University in 1969, under the auspices, of Kaiser Chemicals the Industrial Chemicals Division of Kaiser Aluminum & Chemical Corporation. Turk&apos;s thesis furnished much of the information presented in this paper.

Jan 1, 1976

By S. A. G. Poppen, J. Konopka

"Petro-Canada&apos;s project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda&apos;s mine production goal was set at 500,000 tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: Combined the exploration and business development groups Formed teams to search for and respond to opportunity Made our geologists more business minded and our engineers more optimistic Went global Set clear thresholds, farmed out the marginal properties, fast tracked the others Focused reconnaissance exploration where we had a clear competitive advantage Became a "flexible" partner to both juniors and seniors Is it working? A number of successes, near successes, and outright failures are discussed. The main result is a much higher rate of opportunity flux which is essential for success in the mining industry.

Jan 1, 1999

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By Robert V. Price

It is a pleasure to be here today to discuss coal&apos;s prospects with the Society of Mining Engineers of AIMS--- a group destined to play a crucial role in shaping our national energy future. Much has been said lately about attaining domestic energy self-sufficiency, but to date, little has been done. Oil tankers from Venezuela and Kuwait continue to glide across the seas to meet our incremental energy needs. Meanwhile, our principal domestic energy resources -- oil and natural gas reserves in the Outer Continental Shelf and the oil shale deposits and the coal lands of the West -remain untapped. Help, however, appears to be on the way. In a forceful address last fall, President Ford called for the elimination of oil as a fuel for base-loaded power plants and its replacement with coal by 1980. He also urged the accelerated leasing of federal lands on the Outer Continental Shelf, the resumption of coal leasing on federal lands, and the development of a new energy conservation policy. There are, of course, many details left to be worked out. Language must be developed to put statutory flesh on the conceptual bones spelled out by the President. Congress must act. Regulations must be approved and tested, if need be, in court.

Jan 1, 1975

The first grant of land rights in Australia was pursuant to the Aboriginal Land Rights (Northern Territory) Act 1976. That Act has been at the core of the dispute between land rights and miners&apos; rights. The mining industry believes that the Act, in giving a right of veto to Aborigines with respect to exploration and mining on Aboriginal land, has been responsible for a stagnation in exploration amd mining activity in the Northern Territory. In February 1985 the Commonwealth Government released for public comment its preferred model for national land rights legislation. The model has been opposed by the mining industry because it believes, first, that land rights is a matter which should be left to the States and, secondly, that the detailed mechanisms contained in the model constrain the industry in the manner of the Northern Territory legislation. Aboriginal leaders have opposed the model because it does not, in their view, measure up to undertakings given by the Commonwealth Government and, in addition, it provides for amendments to the Northern Territory legislation which are likely to result in the loss of the Aboriginal veto right. Are land rights and miner&apos;s rights compatible? The answer is yes provided all parties, including Governments, are prepared to talk and compromise and Governments recognise that the grant of land rights and any control by the Aboriginal people of exploration and mining on their land is not a substitute for raising the living standards of Aborigines as a significant group of disadvantaged Australians.

Jan 1, 1986

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young&apos;s moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.&apos; In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young&apos;s modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young&apos;s modulus and substantial magnetic permeability.&apos; Young&apos;s modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.&apos; This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.&apos; The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).&apos;. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.&apos; Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young&apos;s modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.&apos;, " In this method Young&apos;s modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101&apos; dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young&apos;s Modulus Values at 25°C: The modulus values of O&apos;, 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By John Ward Smith

Variations in specific gravity of oil retorted from oil shales of the Eocene Green River Formation in northwestern Colorado were evaluated statistically, demonstrating that these variations are very strongly associated with stratigraphic position and less strongly but still significantly associated with geographic location. Specific gravity of oil retorted from these oil shales apparently varies with the carboxyl group content of the oil shale&apos;s organic matter. Higher temperatures accompanying increasing depth of burial probably progressively decarboxylated oil shale&apos;s organic matter producing the decrease of oil specific gravity associated with deeper stratigraphic position. The geographically associated oil-gravity variations were probably produced by regional variation in the original thickness of late Cenozoic extrusive rocks once overlying the Green River Formation.

Jan 1, 1966

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By D. G. Krige

In the world mining scene, precious metals (particularly gold) have recently monopolized the attention in exploration as well as new production activities. As the major world producer of gold, South Africa plays and will continue to play a very significant role in this commodity. This role will, of course, have its consequential effects on the world&apos;s gold supply and, hence, also on the international price of gold. It is essential, therefore, and in the interests of all gold producers that the likely future pattern of gold production in South Africa be estimated such that some measure of production uncertainties can be predicted. For this purpose, some elementary geostatistical models will be used, and the main factors affecting the situation will be analyzed in broad outline only under the following headings: South Africa&apos;s basic gold ore potential in the three categories of: (1) ore remaining in existing mines; (2) extensions to existing mines via unexplored areas and/or reef horizons of lower grade; and (3) new mines, potentially deep or ultradeep. Cutoff grades - operating, marginal, and flotation, for the foregoing three ore categories, respectively. The availability of production, financial, and other resources required. Cutoff grades will, of course, depend on cost levels (operating and capital), future inflation and cost escalation trends in South Africa (SA), and/or gold price trends (in US$ and via the exchange rate in SA Rand terms). The differentials in inflation and escalation trends with those in overseas countries, mainly the USA, will, in general, set the scene for future exchange rate levels of the Rand. To predict the effect of various cutoff grades on future gold production from South Africa, it is essential to use geostatistical models. The applicability of such models is tested against past records of price, cost, and grade trends and then applied to the estimated ore potentials. These models were referred to briefly in a paper at a recent seminar on gold (Krige, 1986) but are discussed in detail herein. This lecture was intended originally to cover only technical aspects, but, in view of South Africa&apos;s position internationally and the possible effect of sanctions, internal unrest, and strikes on gold production, a brief reference to the third factor above (availability of production, financial, and other resources) seems appropriate.

Jan 1, 1988

By Lynch K. S, Street R. P

Hamersley Iron&apos;s pellet plant at Dampier involves ore drying, dry grind- ing in ball mills, disc balling and, indurating by use of the straight grate system. After five years of operation, the plant&apos;s output has been increased from the design capacity level of 2 M.T.P.Y. to 2.5 M.T.P.Y. Steps taken in equipment modifica- tion, improvements in process control, and changes in maintenance procedures are described.

Jan 1, 1973

By Thomas R. Kuesel, Harvey W. Parker

INTRODUCTION This paper describes the use of a shield and compressed air for construction of a short section of a pair of twin single-track tunnels for the Metropolitan Atlanta Rapid Transit Authority (MARTA) transit system. Although only two blocks long, this section posed the greatest difficulties to both engineers and contractors, and is the most expensive section of line construction on the MARTA system. All this derives directly from its setting--these tunnels had to be constructed through mixed-face conditions. SETTING The Broad Street tunnels form a link between the Peachtree Center and Five Points Stations, in the heart of Atlanta&apos;s central business district (Figure 1). Peachtree Center sits atop a solid rock ridge, which inspired the design of a deep rock-mined station, as described in the 1979 RETC. Five Points Station is MARTA&apos;s hub--the intersection of the system&apos;s two main branches. It is located in the old railroad gulch, a filled-in erosional valley at the base of Peachtree Ridge, and was constructed by open-cut methods. The alignment and profile of the Broad Street tunnels were closely constrained by these two adjacent anchors, and in the six-block stretch between them there was very little room for maneuvering. Since the rock ridge petered out about in the middle of the section, it was evident at the outset that there would be about two blocks of rock tunneling at the north end, two blocks of soft ground construction at the south, and two blocks of mixed-face in between. It is this central two-block section that is the focus of this paper.

Jan 1, 1981

By L. A. Panek

A new pillar strength formula is presented, incorporating a function P of size and shape, which takes into account the size-shape interaction effect as well as the enhanced strength exhibited by wide pillars. Existing pillar formulas, lacking these capabilities, are not suitable for extrapolating small-specimen test results to mine-pillar sizes and shapes. Interpreting compressive-strength test results as function of P clearly reveals wide-pillar behavior in much old test data. Model relationships are discussed, along with their scaling implications.

Jan 1, 1994

By T. D. Dreger

In the spring of 2009, Suncor Energy Inc. technical personnel saw an opportunity to improve planning and mining of overburden material in order to address aggressive construction goals and increased mining complexity. By tying together current and historical equipment performance, geological model information, and material observation in the field new operating elevations for the shovels were developed. At the same time, methodology of recording and reporting overburden movement through the Modular Mining DISPATCH system was changed. The result of this first stage of improvements was an increase in construction-grade material available at the face. The personnel involved realized that other opportunities were available to build on the initial successes and establish processes that would stand up to attrition and experience levels. A cross-functional technical team was assembled to identify ways of further improving workflows around overburden mining. Some of the opportunities realized include greater alignment between planning, reporting and operations as well as development of reporting tools that help steward Mine Operations to the plan. All of which have resulted in Suncor meeting or beating its forecast overburden targets. The cross-functional technical team continues to seek out new and better ways of doing business so Suncor can continue to deliver on its commitment of outstanding performance and results.

Jan 1, 2012

By B. C. Litzinger

Minerações Brasileiras Reunidas S.A. - MBR is a brazilian iron ore mining company geared for the export market. It is controlled by Companhia Auxiliar de Empresas de Minerações - CAEMI through its subsidiary Empreendimentos Brasi leiros de Minerações - EBM which holds 51% in MBR and is formed by CAEMI, the six major japanese steelmills and five japanese trading companies, Universe Tankships, Inc., and Indústria e Comércio de Minérios S.A. - ICOMI. The remaining 49% of MBR&apos;s capital are held by St. John del Rey Mining Company, a subsidiary of The Hanna Mining Company. MBR iron ore reserves exceed 1.5 billion tons of high grade ore distributed in 36 deposits located in the so-called IRON QUADRANGLE in the State of Minas Gerais. The Aguas Claras Mine is the largest presently known and highest grade deposit owned by MBR. Other mines such as Pico, Mutuca and Jangada are in operation at a combined rate of production of about 2 to 2. 5 million tons per year. The project consists of mine, railroad and marine terminal (slide). The Aguas Claras deposit, which is located about six kilometers southeast of Belo Horizonte the Capital of Minas Gerais, was selected for initial development. The Sistema Regional Centro of the Rede Ferroviária Federal, through its 6th Division known as the "Central " is responsible for the transportation of MBR ore, and provided the necessary railway construction to connect Mine and Terminal. The Terminal is located on Guaiba Island near the entrance to Sepetiba Bay, at about 120 kilometers west of Rio de Janeiro.

Jan 1, 1974