Search Documents

By D. R. Mathews

Electrorefined vanadium was evaluated with respect to tensile properties and the effects of interstitial contaminants in the temperature range of 77° to 273° K. The yield strength of 18,500 psi and hardness of 63 diamond pyra-mid hardness (DPH) of electrorefined vanadium are approximately equal to that of iodide crystal bar vanadium. The ductile-brittle transition temperature was found to be below 77° K, but with 0.175 weight-percent oxygen or 0.10 weight-percent nitrogen, it increased to between 123° and 190° K. With carbon content up to 0.11 weight-percent, the transition temperature remained below 77° K. The yield strength of the interstitial-containing alloys can be expressed by: au = 7.5 + 480 (pct N) + 290 (pct 0) + 280 (pct C), where au is the upper yield stress in 1,000 psi at 273° K. Profuse deformation twinning occurred in the alloys tested at 77° K. However, twinning could be suppressed by dissolved oxygen or nitrogen in excess of 0.15 and 0.086 weight-percent, respectively. Carbon, even though present in excess of the solubility limit, did not affect twinning.

Jan 1, 1965

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By R Ayothiraman

Tunnel excavation may induce adverse effects on nearby existing structures/foundations in urban areas. Accurate prediction of tunnelling effects on pile foundations of nearby structures in the urban environment poses a major challenge during design. Several studies have been undertaken to understand the mechanisms of the soil-tunnel-pile interaction, which focused only on influence of tunnelling on nearby existing building and foundations. However, effect of pile loading on existing tunnels did not receive enough research attention so far. So it is essential to measure the response of existing tunnel-lining due to loading on newly constructed pile to assess to the safety against the additional forces/moment caused by pile loading and to evaluate the critical distance for the proposed construction of any structures from the tunnel location. This paper presents result of three-dimensional (3D) finite element analysis carried out in ABAQUS to investigate the effects of pile loading on existing tunnels embedded in cohesive soil. It is found that the effects on tunnel lining depend on horizontal separation distance between pile and tunnel as well as location/elevation of pile tip with respect to tunnel location.

Mar 8, 2011

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields, with rapid depletion of existing reserves, emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry for meeting increasing market demands; but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields. Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most current operations are of the pressure-maintenance type, in which the reservoir pressure is maintained or partly maintained by injecting natural gas to in-crease oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes current gas-and water-injection projects in California.

Jan 1, 1952

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

Risk management has taken on renewed vigor since the economic crisis of the late 2000s. The resources of governments, individuals, and corporations are being stretched to a point where only the most promising projects move forward. Risk management is a crucial part of the decision making process, yet it remains a broad term that includes disciplines from engineering to finance. A collaborative effort will be necessary to ensure that the most auspicious and appropriate projects are the ones moving forward. Risk management can be quantified to an extent by comparing the likelihood of an instance with the result of consequence of the instance occurring. In this manner it is possible to assign risk factors to instances and ultimately, begin to associate monetary value to the instance. Carbon sequestration is an emerging field that has a number of unique challenges. Risk management and mitigation must be an integral part of the overall picture. This begins with the planning and design phase, continues through implementation and production, site closure, and does not cease until termination of liability. The ability of carbon sequestration projects to successfully assess, mitigate, and recover from leaks will be a decisive characteristic of overall success. The costs of mitigation and failure will need to be analyzed on a test level, but will still need to be reliable enough to extrapolate to a commercial level operation. This paper will build a risk management profile based on case studies and field tests in Tennessee and Virginia. These tests are scheduled to commence in late 2013 and consist of small-scale injection tests in unconventional storage reservoirs with an emphasis on enhanced coalbed methane (ECBM) recovery and enhanced gas recovery. The ultimate goal will be to provide a clear and concise direction to move carbon sequestration from the test phase to commercial scale. While it is necessary from a risk management perspective to analyze all risk points, the scope of this paper will focus on pre-injection risk assessment for carbon dioxide (CO2) leakage potential. Despite the differences between the two tests, CBM compared to shale among other differences, a framework for analysis and mitigation can be developed pertaining to leakage risk. The probability of each type of failure will be assessed and analyzed, and plans to mitigate or reduce these risks will be reviewed.

Aug 1, 2013

By Donald Deardorff

"Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head.Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required."

Jan 1, 2017

By Donald Deardorff

Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head. Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required.

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Sabri Ergun

This report gives the result of investigations of coals of different rank, coal com¬ponents, chemically and thermally treated and irradiated coals, and sedimented organic matter. In most studies the arbitrary parameters obtained from the usual quantitative profile analyses are not given largely because they lack physical meaning. Instead comp interpretations are offered. X-ray patterns of high-volatile bituminous and lower rank coals are not self¬-sufficient for structural interpretation by the methods of analysis developed to date. The patterns of hydrogenated and dehydrogenated coals indicate that the basic change in the structure of bituminous coals with increase in rank is the conversion of alicyclic structures into aromatic layers. In low-rank anthracites the aromatic layers are about 10 A in size. The increase in rank is the result of coalescence of layers. High-rank anthracites have layer sizes of 25 to 40 A and exhibit the development of three-dimensional (hkl) reflections of graphite, indicating ordering of adjacent layers. In meta-anthracites the layers are > 1000 A and the basic structure is that of defective crystalline graphite. The well-known petrographic components in low-rank coals have different structures; the differences dissappear in low-volatile bituminous and higher rank coals. The patterns of sedimented organic matter, except impsonites, differ from those of coal hydrogen contents are high, and their X-ray patterns are consistent with those of structures. In contrast to normal coals, the patterns of uranium-bearing coals show increased diffuseness with decrease in hydrogen content. The diffuseness is accompanied by increase in the uranium content of the coal. It is very likely that high uranium-bearing coals have predominantly tetrahedral structures.

Jan 1, 1968

By R. A. Beall, S. L. Ausmus

The development of a completely water - free expendable graphite mold material , useful for reactive metal castings , has been detailed . Mixing and curing variables have been evaluated both by physical testing of the material itself and by castings of titanium , zirconium , and hafnium . The blend of powdered graphite , cornstarch , dextrin , cereal binder , linseed oil , and Carbowax -4000 is a successful mix when mulled in a carbon dioxide atmosphere , and properly cured and fired . The primary advantage of this material is its adaptability to standard foundry techniques ; i . e . , core blowing and hand ramming . Temperatures in the curing and firing cycles do not exceed 960 ° C , and no vacuum firing is required .

Jan 1, 1964

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By L. Simpson

South African is a repository of significant deposits of a variety of minerals. The Citigroup confirms this assertion with an estimate of in-situ valuation of US$2.5 Trillion. The mining sector plays an important role in the South African economy. In addition to the mineral resource base South Africa has other comparative advantages. Firstly, South Africa retains major mining companies that participate globally, including Anglo American, Goldfields and De Beers. Their global involvement offers much to the local mining sector and the broader economy. Secondly, government established research councils. The Council for Geoscience (CGS) was established to manage the Geological Survey of South Africa, including the reduction of geo-scientific investment risk. The Council for Scientific and Industrial Research (CSIR) promotes industrial development, including mining technology development. Mintek undertakes mineral research from mineral examination of ores, to extraction and refining technologies and manufacture of end products. Thirdly, South African universities teach and conduct research along the mineral value chain. They have increased their minerals graduates? capacity, thus advancing knowledge and skills. Knowledge and technical progress are behind productivity growth and emergence of competitive advantage. The research and development (R&D) capabilities of industry, science councils and universities, working in unison, will enhance the competitiveness of the South African mining industry. The National System of Innovation (NSI) requires multi-disciplinary, collaborative research. Key R&D elements, including skills and expertise, funding and facilities, must be available to implement a long-term national strategy or programme. Improved international collaboration and partnerships between government, academia and industry driven human resource development (HRD), ultimately develop the critical mass for inter-generational skills requirements. This trend requires an expansion of research collaboration programmes. Decisions involving investments and collaborative actions pertaining to R&D in the sector necessitate an analysis of the South African mineral value chain R&D capability. This paper analyses the evolution of R&D capability from exploration to refining, tertiary education, science councils and industry. The political economy of the evolution of this capability is analyzed in relation to the central role that the South African government plays in creating an appropriate supporting environment and related initiatives to enhance R&D and innovation. Keywords: research and development (R&D), science councils, universities, industry, innovation policy, South Africa

Sep 1, 2012

By Bill Linville

During fiscal years 1967-68, the Bureau of Mines produced 185 technical papers and reports about petroleum and oil-shale research, which were published either by the Bureau or by others as referable scientific literature. Numerous other reports were prepared for Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau. Research performed during the reporting period by the Bureau on petroleum, natural gas, and oil shale was classified by 71 active projects. A basic appropriation of $3,575,000 was supplemented by $1,300,000 in fiscal year 1967, and that of $4,043,000 by $1,402,000 in fiscal year 1968, making the appropriated-to-supplemental fund ratios about 2.8 to 1 for fiscal year 1967 and 2.9 to 1 for fiscal year 1968. In fulfillment of the mission of the Bureau, through planned research programs, methods for producing and utilizing petroleum were improved. The continued conservation of this natural resource of petroleum, including crude oil, natural gas, and oil shale, was pursued through research performed by some 350 personnel at two petroleum research centers and two petroleum research laboratories supervised and supported by administrative personnel of the Bureau and the Department of the Interior.

Jan 1, 1970

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By E. Milosavljevic, C. H. Bucknam, K. L. Gabby, T. C. Eisele

"Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately, mercury is recovered along with the silver as mercury/silver/gold amalgam, which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution. IntroductionThe dissolution of mercury along with precious metals during cyanide leaching is a long-standing problem, which can result in significant mercury toxicity issues (Washburn, 2003). Mercury is first dissolved by the cyanide solution, and then, since it has a great deal of chemical similarity to silver, it follows silver throughout the concentration and recovery processes, ultimately being recovered as a silver/ mercury amalgam when the metal is precipitated by either the Merrill-Crowe process or by electrowinning.While it would be desirable to either prevent mercury dissolution entirely while still allowing silver dissolution, or to selectively capture mercury before the precious-metals recovery step, there is not yet an effective and economically practical approach to doing this (Grosse, 2003; Ravichandran, 2004; Misra, 1998; Pai, 2000). There are a few processes that have been proposed, such as differential adsorption. While activated carbon, as used in the carbon-in-pulp process, is not highly selective between mercury and silver (Washburn, 2003), it may be possible to achieve some separation by selective elution of the carbon to produce high-mercury and low-mercury eluates (Bunney et al., 2010). Certain synthetic resins were shown to be selective for gold but are more expensive than carbon, requiring special equipment, and have not yet been shown to be selective for mercury (Grosse, 2003). There may be potential for differential dissolution approaches, as thiosulfate leaching does not dissolve mercury sulfides as readily as it dissolves gold (Oraby et al., 2010), and it is possible that it may be similarly more selective for dissolving silver relative to mercury. Some work has also been done with selective precipitants, such as sodium polythiocarbonates (Bucknam, 2007), and 1,3-benzenediamidoethanethiol (Matlock, 2002). Common problems with these approaches include introduction of a solid:liquid separation step, reagent costs, the need to measure the mercury concentration for process control for minimizing silver losses, and regulatory requirements to retort otherwise stable mercury concentrates."

Jan 1, 2015

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

[lllc purpabr at thla report Vd, Lu JeLermlnr the health ar1J sdfet?; Nene11Le a octatc?J ultll Lne oar L.t support Ydlll ..up.I,ated lu dltetllative cupPurt svsLem, larrellLty hcle.g uaeJ af the Len,::rat 1, UI.Jlng 11-al tl. .1 a d 1 c L V h S LIdl'. L dal. I -ten- lu L he tt I .. L'., etuJ I e. 11'? L_1,1'1,11 .Jtd.. it, ..urn,at'l core ,LuJICCill JhLdll, an.: ...,La -IL .utia_tel .an LI?r oar of -l: l,.!rl .a..a. Ma terI.I auJ ...11,mc[Ii -ldla,tutcle 11. LI.ac .uwIttIca Welt a, a.. V.alte,, L.. .:Ltail, ..,,L., uI. LuClu,alug) Lelll anci ur devel?puJ I.,r Cul r1 , all. ...~.,rLrI Vt,ILt 1.'ere ~e,1C L? .Lher Gentiaii m111cc t, UL.-rye a Variety o. a rL vyl I pp.1Ca:t..n:. 'a.la IrL ..,_wLeiti, Iapl,.III ,tall ~,..:. IL all, maLertdl c1,arait-erlstIcs, JIRICn,IUIIe. and laden ul1.1 ILc rrgatrelaeuls. ,1 r.? p.'rt .a pro-1Jd, labor rep altrlarnts Jdta and illtlitI ieS tie l,ealtll d?J ,atetV ISSUC ,u-1aled Wit su furl Wall a an, CJl,wttuctSOn, I'aLentiaI appll.at1ou:. Ior support Walt, ,a,. , a, sdV.u,L111 .., u.1 retreating lungval1, single -t r-, roar al,- pi r. [,-+ln, anJ SuhIU..,Ina, Sill] b1OpplllgL ale 1:111neated aid al? e.aIWRac AS Sddemcni LV pre,C'IIL..: .,f LI. Clabllhty r+t rlul,I.,y111I? ulg4,rt .I Le.l,lwlug,. Lr i,,,rCASC Lllc rtCVLLrS rat, u., retrc.+tlnp .unui.,11? ur L., elply, A d v Ctnp IuI-,wall in uer;-!y iy1ng seam, . 11111.a1L .a1,.'iI1.-I,.. nr S.IU1tIVlil a1 milItlI; Lust, La LIldnt;2S L.~ gey support Vait Id tdmcLera la dlaa presents,.]

Jan 1, 1980

By J. E. Hoffman

The operation of the U .S Metals Refining Company, USMR Co. is defined below by the description of a variety of unit processes and operations the author encountered during his tenure with the operation, 1955 - 1978. The operations discussed include: sampling and sweating of radiators, processing of Indian Coin, treatment of insulated wire, baghouse and converter dust treatment, blast furnace and converter operation, the electric arc furnace, antimony control, selenium and tellurium products, electrolyte liberation with soluble anodes, and the precious metals refinery. These operations, although peripheral to the primary copper production circuit, were critical to the company's technological and economic base.

Jan 1, 2000