Search Documents

By G. Gao

Flyash from municipal solid waste (MSW) incinerators is frequently classified as a characteristic hazardous waste due to its lead and cadmium content. Extensive investigation has therefore been carried out to detoxity the flyash by leaching and to recover lead, cadmium and zinc. Detoxification can be accomplished by leaching in HCI/NaCI solutions. Optimization of leaching conditions for effective detoxification and subsequent metal recovery can be achieved by controlling the acidity of the lixiviant and flyash to lixivaint ratio. Lead and cadmium In the leaching solution is recovered by cementation with zinc dust. Leaching and cementation experiments have shown that zinc concentrations suitable for electrowinning, > 15 g/liter, can be achieved. Experiments have also been performed to determine the effects of pH, particle size of the zinc dust used, quantity of zinc added and dissolved impurities on the cementation kinetics. After recovery of lead and cadmium, electrowinning or electrowinning coupled with solvent extraction can be used to recover zinc. A process flowsheet is presented.

Jan 1, 1991

By James O'Brien, Lyman Frost, S. Elangovan, J. Stephen Herring, Joseph Hartvigsen, Carl Stoots, Anthony Nickens

"Carbon dioxide recovered from concentrated sources, such as metallurgical reduction furnaces, cement kilns and fossil power plants can provide a valuable feedstock for a synthetic fuels industry based on energy from nuclear, solar, wind and hydropower sources. High temperature co-electrolysis of CO2 and steam to produce synthesis gas has been demonstrated using reversible solid oxide fuel cell technology. Where a source of high temperature process heat is available, such as from an advanced high temperature nuclear reactor or solar dish concentrator, the endothermic electrolysis reactions can utilize both thermal and electrical inputs in such a way that the conversion efficiency within the cell is 100%. Synthesis gas produced in a coelectrolysis cell has been further reacted over a catalyst to produce conventional hydrocarbon fuels. Widespread implementation of synfuel production from CO2 will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles.IntroductionFor the past several years, Ceramatec, Inc and the Idaho National Laboratory (INL), have been studying the feasibility of high temperature solid oxide electrolysis for large-scale, nuclearpowered hydrogen production under the U.S. DOE’s nuclear hydrogen initiative (NHI) as an alternative to the thermochemical process. Parallel to this effort, the INL and Ceramatec have been researching high temperature co-electrolysis of mixtures of steam and CO2 to produce syngas:"

Jan 1, 2008

Successful evaluation and exploitation of resources and reserves relies on the collection of high quality sample data. The quality of the sample data must be maintained through the application of a robust quality assurance and quality control (QAQC) program, including documentation of sampling procedures, training of sampling personnel and the regular monitoring of control samples. However, the application of QAQC programs in the minerals industry is often poor and the purpose misunderstood. It is all too common to have good quality control data collected, but no analysis work carried out until after drilling is completed. In a lengthy drill program, this can lead to problems not being discovered and corrected as they happen. Moreover, rectifying problems afterwards will be costly in terms of time and money, if not impossible. The consequences of poor quality sample data are many and include such effects as over- or underestimation of block grades, misclassification of ore and waste, and lower confidence in the resource/reserve models. The purpose of this paper is to highlight, using case studies, the importance of good QAQC practices to monitor the quality of sampling and laboratory sample preparation and analysis.

Mar 1, 2010

By S. F. Burks

"This paper develops themes explained at two SAIMM platinum conferences. Optimization techniques can be used to significantly increase the value of mining businesses by enabling better long-term planning decisions. Open pit and underground mine design, mine scheduling, cut-off grade and blending, stockpiling, and the linking of these to flexible elements of the metallurgical recovery processes are all evaluated together. Transport or sale of intermediate products and the requirements of the product metal markets can also be considered. Experience shows that net present value (NPV) can be increased significantly, usually even before the expenditure of significant amounts of project capital. Recent studies of NPV have aimed to simultaneously evaluate the impact of the optimized financial solution on the non-financial features of a project or operation.The case study presented comprised a commercially orientated review of the prefeasibility study designs and cost estimates of a platinum group metal (PGM) project in South Africa, followed by value chain optimization and sustainability studies of the project carried out simultaneously to identify potential value uplifts to be gained and guide the owners’ team going forward into the feasibility study phase. Some of the major aspects of the project that were found to have significant potential to add value included enhancement of the business model by the application of activitybased costing and theory of constraints, focus on the highest net value portions of the orebody in the early years of production, enhanced and optimized scheduling of the underground mining operation, application of dynamic grind and percentage mass recovery from ore to flotation concentrate (also known as percentage mass pull) to optimize revenue, application of elevated cut-off grades early in the life of mine, matching of the mining and processing capacity, expansion of the operation subject to capital availability, and installation of downstream processing facilities subject to regional third-party capacities.The investigation of non-financial project features focused on demonstrating that a financially optimized solution could also have a number of other benefits. These are mentioned briefly in the paper, which aims to present the status of the project at an early stage of its development."

Jan 1, 2016

By Randall Wheeler

In early 2008 we were asked by a quarry to become involved in a conflict with a pipeline company concerning blasting near one of their underground high pressure gas lines. The pipeline company, without the quarry’s knowledge, had sought and obtained a temporary restraining order against the quarry forbidding them from blasting near the pipeline.

Jan 1, 2011

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By D Kent, D Eisner

A lot of talk has been generated about the so called ‘Internet of Things’ (IoT) and its potential to transform the way we interact with our homes and devices. But the true potential and value of IoT is not going to be realised by the general consumer but by businesses.This paper outlines the application of IoT in mining and how it is a natural extension to the base networks becoming commonplace in both surface and underground mines. The potential for ubiquitous monitoring throughout a mining operation at low capital and support costs will transform the ability to monitor, analyse, report and manage all of the key processes involved in a mining operation.Importantly, the paper will discuss the practical applications that the IoT offers mining and explain how this really is transformative technology, not just the latest buzz words from the information technology (IT) world. If leveraged correctly the impact on mining, its cost base and efficiencies, is enormous.CITATION:Kent, D and Eisner, D, 2015. What the internet of things means to mining, in Proceedings Third International Future Mining Conference, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

By L. M. . Chia

The successful treatment of waste materials to recover metals with acceptable purity is often hampered by the presence of undesirable impurities. The problem is further complicated by the need to insure that any residues or solutions generated are environmentally acceptable. Hydrometallurgical processes involving leaching- solvent extraction-electrowinning offer some attractive features which address many of these problems. However, in certain instances trace impurities that contaminate the organics are difficult to chemically strip and interfere with the overall process efficiency. A new processing scheme has been developed which appears to provide some attractive alternatives for impurity removal from organics. It has been shown that many ionic impurities can be electrochemically removed from the organic by spontaneous direct reduction using solid metals. A variety of metal ion impurities have been removed from selected common organic extractants such as D2EHPA and TBP using different metals as the reducing agents. The results and probable mechanisms involved in the reactions are discussed.

Jan 1, 1994

By A. Singh, M. Ntlhane, V. Ross, M. Dlame

"Fine valuable particles are often lost to flotation tailings streams due to inefficient collection by air bubbles as well as passivation of surfaces by oxidation and slimes. The application of high-shear hydrodynamic cavitation devices (HCDs) to overcome this problem has already proven to be a considerable success in the industry. This paper details the results of further investigations that were undertaken at Mintek to better understand the mechanisms involved when preconditioning feed slurries in an HCD. By promoting inter-particle attrition and conditions of high shear within the reactor, cleaning of particle surfaces is enhanced as well as the formation of superfine (nano) bubbles which are believed to aid their agglomeration and subsequent collection by normal sized bubbles. In order to broaden the envelope of understanding with regard to application of the technology, rather than tailings material as investigated earlier, a Platinum Group Mineral (PGM) UG2 ore from the Bushveld Complex in South Africa was used in this study. The results of a series of batch flotation tests in a 10L Denver cell are presented, being conducted after the feed has been subjected to different methods of preconditioning. It was demonstrated that the preconditioning significantly improved the flotation kinetics of the PGMs, the optimum being obtained after around 20 passes through the reactor. This was accompanied by a much enhanced recovery-mass pull relationship and a significant improvement in the grade-recovery response. Significantly, the selectivity between the PGM and the deleterious chromite (expressed as Cr2O3) gangue more than doubled under these conditions. Modelling of the PGM data by means of the modified Kelsall model indicated that both the fast and slow floating rate constants were improved.INTRODUCTIONIt is well known that the flotation recovery of fine and ultrafine particles, typically less than 10 micron in size, is a challenge (Yoon et al., 1989; Miettenin et al., 2010). Although these particles are typically well liberated, due to their very low mass and inertia, the collision efficiency with air bubbles is low as a result of the inability of particles to penetrate the liquid streamlines around bubbles. Hence the probability of contact is often regarded as the ratedetermining step in flotation of ultrafine particles. Introducing more power into conventional flotation machines is likely to solve only part of the problem, as conventional mechanisms are effective only to a point in terms of shear and micro-turbulence. Further challenges are posed by the treatment of low-grade or oxidised tailings dump material, where valuables are passivated due to prolonged exposure to the atmosphere or slimes. Over the years, various mitigating strategies have been investigated, including the use of dissolved air flotation (Martinez-Gomez et al., 2013; Calgaroto et al., 2015), shear flocculation (Subrahmanyam and Forssberg, 1990), seed or carrier flotation (Tabosa and Rubio, 2010), sonication to clean particle surfaces (Aldrich and Feng, 1999; Newell et al., 2006), high intensity conditioning (Bulatovic and Salter, 1989; Chen et al., 1999; Tabosa and Rubio, 2010), and various electrochemical approaches such as changing Eh in order to promote formation of dixanthogen, dissolution of oxidation products by lowering the pH, activation by sulphidisation (Newell et al., 2006; Becker et al., 2014), and the use of alternative collectors."

Jan 1, 2018

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012

By K. Olsen

As aluminum alloy usage in automobiles grows, there are increasing demands on recycling processes and facilities to deal with mixed alloy automotive aluminum scrap. These processes and facilities strive to produce near virgin aluminum stock, which can be relatively costly and difficult. One alternative is to use physical processing methods to upgrade the scrap properties instead of chemically refining the scrap. The Impulse Atomization Process (LAP, patent pending) is a new process for making metallic and ceramic powders. It can produce fine homogeneous microstructures in scrap aluminum alloys due to high undercooling and rapid solidification. The particles have a very narrow size distribution and are in a convenient form for consolidation. This paper compares and contrasts the microstructural features of Impulse Atomized. and quenched Impulse Atomized powders,&apos; for both AL6061 and a scrap aluminum alloy composition.

Jan 1, 1995

By L. Bbosa

Positron Emission Particle Tracking (PEPT) and the Discrete Element Method (DEM) are used to investigate Power Draw in a laboratory scale tumbling mill. The mill is run dry in batch mode at different speeds using mono-size charge of glass beads, and is mounted along with a torque transducer to measure power. Particle tracking information from PEPT is used to reconstruct the motion of glass beads and infer the overall charge behavior, while DEM is employed to simulate particle motion and interaction, with collision mechanics calculated using the Hertz-Mindlin contact model. For PEPT and DEM data, the product of torque and average angular velocities in discrete cells are accumulated to obtain mill power. This method is found to be within statistical agreement with measured power for all tests. Spatial distributions plotted from this approach highlight the regions of the mill that draw the greatest power. A second technique to obtain Power Draw from DEM data which sums particle forces against the mill geometry is similarly found to accurately predict mill power with lower statistical error. Keywords: Power Draw, PEPT, DEM

Sep 1, 2012

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016

By E. O. Strahl

In the search for economic mineral deposits, the need for efficient mineral or chemical assays is of prime importance. Costly analytical methods and long delays in obtaining assay results severely limit the effectiveness of an exploration program. The assay problem becomes acute once a potential ore body is located and large numbers of samples are generated in close interval drilling programs. In order to avoid the delays and high costs of extensive assays, the exploration geologist or mining engineer is likely to be required to curtail his drilling program, composite samples, or restrict the required analyses to a limited number of critical elements. As a result, the definition of the potential ore body may be less than needed for final economic evaluation. The assay requirements for bauxite exploration usually involve a considerable number of total elemental and empirical analysis. Since the Bayer process for extracting alumina from bauxite involves the selective dissolution and reaction of specific minerals from the bauxite, a direct chemical analysis for elemental composition yields only a portion of the data required to effectively describe the potential economic value of ore body or deposit. To fully characterize the economic value of a bauxite requires digestion, mud separation and mud settling tests under conditions approximating a commercial Bayer plant. A close approximation of the process behavior of a bauxite also can be calculated from a combination of the chemical and mineralogical analyses. By determining the elemental chemistry, mineralogy, and Bayer plant processing characteristics of a few samples of a given bauxite, correlations can be derived that permit defining a bauxite in terms of a given set of process conditions.

Jan 1, 1977

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By D. Newman

Ground control is critical to the success of a safe and productive underground stone mining operation. The primary focus of the ground control engineer is the stability of the roof or back; development and benched pillar stability; stability of the sill pillar between vertically adjacent mining levels; and floor stability. Roof stability begins with the selection of a stable back horizon based on the presence of a thin shale parting, stylolite or other discontinuity from which the production shot can easily peel away, leaving a stable back stratum. Bed thickness, fracture spacing, jointing and the material properties of the roof strata control the room width; the decision whether to bolt the roof; the bolt length, type and diameter; and the spacing of the roof support. Horizontal stress controls the header and crosscut azimuth. The mine operator should avoid driving perpendicular to the maximum horizontal stress direction. Where this is unavoidable, narrowing the opening width, narrowing pillar centers, increasing the support density and using three-way intersections are alternatives to remediate shearing along the roof-rib interface. Stable pillar dimensions depend upon the interaction of the vertical stress resulting from overburden thickness and multiple-level interaction of overlying level or levels; the mining height during development and the final mining height after floor shots are taken during benching; the presence of faults, folds or joints passing through the pillar; and limestone lithology, recognizing that the presence of oolitic bands, shale partings, joints and bentonite beds creates zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone typically exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture-sensitive strata, weak stone bands or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. To illustrate these ground control issues, this paper presents four case histories that are a mix of ground failures and successful mining. The focus is on the geotechnical data required for roof, pillar and floor design and stability analysis.

Jan 8, 2017

By M. E. D. Raymont

"During the history of the sulphur industry there have been three distinct phases of production. Factors controlling supplies during these periods have shifted from demand for sulphur to demand for energy and a cleaner environment. The pattern of brimstone production is t raced through these phases and includes estimates of future supply; these indicate an involuntary excess production of some 20 million plus tons per year by 1980 unless some large-scale new uses are found. Traditional uses for sulphur, including fertilizer, chemicals, fibers, etc., are generally expanding slowly; how• ever, supply in ""by-product"" form alone will soon outstrip demand. The predicted oversupply situation can be corrected by the development of novel potential markets. Promising areas include construction materials, insulation and plastics, among others."

Jan 1, 1972