Search Documents

By JA Vallejos

High stress underground mining poses a significant challenge to rock mechanics and rock engineering. To overcome theses challenges significative improvements in solutions and best practices of the design and operation of mines under high stress have been developed and implemented. This paper presents certain topics related to the management of high stress for sustainable underground mining. The topics include; the effect of preconditioning techniques (destress blasting and hydraulic fracturing) in the seismic rock mass response to underground mining and the dynamic behaviour of rock support systems. The opportunities associated with research in rock mechanics and practical rock engineering are discussed.

Apr 26, 2022

By Michael Murphy, Mark Van Dyke, VASU GANGRADE, Brent Slaker

Room-and-pillar mining in multi-level underground stone mines come with unique pillar stability issues. The pillar stability in these mines primarily depends on the thickness of interburden between mining levels and the staggering of pillars. NIOSH has previously established pillar design guidelines for shallow, flat-lying mines and single-level operations, but there is little guidance for ground control design in multiple-level stone mines. Therefore, to improve the overall understanding of ground control in these mines, a microseismic monitoring system has been installed at a multi-level underground stone mine in Tennessee with up to a 243-m overburden and a 7-m interburden thickness between levels. The microseismic system is comprised of nine uniaxial accelerometers and one triaxial accelerometer installed in the interburden. The seismic array is locally focused with all sensors installed within a 625 m2 area and is setup to monitor the seismicity around the formation of the pillar in the lower mining level. Data is collected over 11 months and comprises of over 1,000 high-confidence events that have been located in the study area comprised of post-blast activity. The event locations were identified using a 3D-velocity model, with an average 4-m location accuracy for this array calculated using the system data. Most observed seismicity was on the excavation boundary, both in the interburden and in the roof of the top level. At this stage of analysis, there are no significant rock failures with which to correlate seismicity, but event locations correlate well with presumed damage in the vicinity of blasts.

Apr 26, 2022

By Jon A. Carlson, W. Scott Williams

The EKATI"" Diamond Mine commenced operation in October 1998. It is operated by BHP Diamonds Inc., which is a part of the Non-Ferrous and Industrial Materials Division of BHP Minerals, a business unit of BHP Company Ltd. of Melbourne, Australia. The EKATI"" Diamond Mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). In December 1993, an office was opened in Yellowknife, Northwest Territories specifically for the then Northwest Territories Diamonds Project (EKATI"" Diamond Mine) development. EKATI"" Diamond Mine is located 300 kilometres northeast of Yellowknife and 200 kilometres south of the Arctic Circle in the Northwest Territories of Canada (Figure 1 ). The site is located in a remote tundra area of continuous permafrost, north of the tree line, which is part of the Canadian Shield. Wekweti (Snare Lake), a Dogrib community approximately 180 kilometres southwest of the project, is the closest neighbour. The mining area and facilities lie within the 10 960 hectares land leases held by the joint venture. The total claim block (core zone and buffer zone joint ventures) covers 344 000 hectares. To date, more than one hundred kimberlite pipes have been identified within the claims. Five of these provide the basis for the present mine plan. Total capital investment in the project is over C$700 million. At full production employment will be about 600, including employees and long-term contractors, with over 33% being Aboriginal from the Northwest Territories.

Jan 1, 2001

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By D. Randolph Berry

The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactorily demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No, 1 Mine in Grant Town, West Virginia.

Jan 1, 1973

By Michael Radnor

The purpose of the study was to 1) examine the social and economic impacts of surface mine blasting in relation to variations in conditions of terrain and geology, population density and type, levels of ground motion and air blast; 2) consider technical, legal and government policy issues; and 3) examine the potential, nature and extent of surface mine blasting impacts and its regulations upon both communities and surface mining companies. Phase One designed the empirical research and technical analyses of Phase Two, focused upon surface coal mining and quarrying in the Eastern U.S. Several broad conclusions are evident: 1) blasting is not the major issue for communities or surface mine companies; 2) while the number of instances of severe cracking or annoyance are relatively small, the impact can be severe for individuals immediately involved; 3) blasting/drilling cost curves tend to rise significantly at intervals below 1.0 particle velocity, in/sec, dependent upon the size of a permit area and the size of a mine; and 4) the legal, complaint, cost and density analyses do not suggest the need for a general lowering of present regulations.

Jan 1, 1981

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By L. H. Duschak, C. N. Schuette

In the years 1850 to 1923, the United States produced 2,426,000 flasks- (73,600 metric tons) of quicksilver worth $120,500,000. California yielded 2,195,000 flasks of this total; the remainder came from Texas, Oregon, Nevada, and A.rizona. Most of this metal has been extracted from low-grade ores, those containing less than 0.5 per cent mercury or 10 pounds per ton. The finished product or " virgin metal" is made at the mine and shipped in flasks. Quicksilver is unique in being the only metal that is liquid at ordinary temperature. Because of this and other physical and chemical properties, it is perhaps more indispensable to industry than any other metal. On the other hand, the quicksilver industry of the world is of vanishing significance" when compared to the major mineral industries with respect to quantity and value of product, capital invested, or the number of men employed. The peculiar value of quicksilver is due to the fact that in some of its applications no substitute is available and in others the substitutes would be unsatisfactory or extremely expensive. Scarcely a branch of science or industry fails to make some use of mercury or its compounds. As a detonator for explosives, mercury fulminate holds first place and in safety and reliability could be replaced only by the highly expensive silver fulminate.t vThrough its use in detonators and in the metallurgy of the precious metals quicksilver is of special importance to mining. In medicine,in the manufacture of electrical apparatus, the production of pigments and antifouling paints, and the general field of experimental science quicksilver is equally indispensable.

Jan 1, 1925

By K. C. Watts

The Silver City mining region is located in Grant County, southwestern New Mexico (Fig. 1). This area is well known, having produced large tonnages of base and lesser amounts of precious metals over the past several years. Mining within the region continues today, as well as exploration activity, which seems to have been on the increase since the recent discovery of a large skarn-associated Zn-Pb-Cu replacement deposit near Pinos Altos, a mineral district within the region (McKnight and Fellows, 1978). Because the Silver City area contains a number of mineral districts and retains promise for additional deposits, as suggested by widespread hydrothermal alteration and favorable igneous rocks, it was selected as the focus of two independent geochemical studies, both seeking to enhance anomaly-to- background contrast in order to improve our abilities to detect blind metal deposits or subtle manifestations of near-surface occurrences. The first of these independent studies involved the systematic sampling of those secondary Fe-Mn oxides that occur within coatings, selvages, and fault fillings, and then the selective extraction of these oxides from the host-rock matrix by chemical methods. The second study sought to isolate clastic Fe-Mn-rich materials from the heavy fraction of stream alluvium. The ultimate source of the clastic Fe-Mn oxides is presumed to be the same coatings, selvages, and fault fillings sought by the direct sampling of joints, but has been transported as a result of lateral erosional processes.

Jan 1, 1981

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944

By A. E. Back

A method has been developed in the laboratory for successfully treating titaniferous magnetite ore from the deposit at Iron Mountain, Wyo. The ore is roasted with 15 percent sodium carbonate to convert the vanadium to a water-soluble form and fix the soda for the subsequent electric-smelting step. Approximately 90 percent of the vanadium is recoverable in a product assaying 80 percent V2O5. The leached calcine is briquetted and smelted in a graphite-lined electric-arc furnace. Substantially all of the titanium is recovered in a soda slag, assaying 60 percent TiO2 and 2 percent Fe, which can be upgraded to 75 to 80 percent TiO2 by leaching with dilute sulfuric acid. The upgraded slag could be utilized for the production of titanium dioxide pigments or titanium tetrachloride. About 90 percent of the iron is recovered as pig iron, containing only minor amounts of vanadium, titanium, and sulfur. The high TiO2 slag compares favorably with slag containing about 70 percent TiO2 being produced by the Quebec Iron & Titanium Corp. at Sorel, Quebec. The data obtained from this investigation indicate that a feasible process has been developed for treating Iron Mountain ore, and larger-scale testing is warranted to develop engineering data for the ultimate utilization of this deposit as a source of titanium, iron, and vanadium. There are adequate supplies of basic raw materials, electric power, water, sodium carbonate, coal, and petroleum products within fairly short distances of Cheyenne and Laramie, Wyo., the nearest cities and probable plant- and labor-supply points.

Jan 1, 1952

By Joseph Chalmers

Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the "gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ultimate recovery of oil from their properties. A number of factors influence the efficacy of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity show a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate of gas injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.

Jan 1, 1930

By Norman R. Paterson

"Under certain conditions useful gravity information of a reconnaissance nature can be obtained with-out measuring elevations by spirit level surveys on the ground. Gravity surveys can become part of a practical exploration program where high cost and slow progress previously hindered their utility. The advantages of the new elevation procedures are realized mainly in remote areas, in areas where ground transportation is slow and difficult and on surveys where the station spacing is large in comparison with the distance of the average optimum level shot. To utilize the advantages, transportation by helicopter or light plane is usually necessary. Methods of obtaining elevation control without leveling include: barometric altimeter survey; photogram-metric -APR spot determinations; methods involving the measurement of gravity gradients. The accuracies of these methods have been tested and compared with the normal accuracy of level surveys. It is felt that each method has its place in reconnaissance gravity work, particularly in the open areas of Northern Canada."

Jan 1, 1960

By C. B. Daellenbach

A prototype particulate size analyzer system was developed that would rapidly determine size distributions of homogeneous and two-mineral materials in the 74-micrometer (200-mesh) to 7-micrometer size range. The system sizes particles in a series of hydrocyclone elutriation steps and senses the weight of the five sized fractions by nuclear attenuation techniques. Size distribution of materials was determined from experimentally developed mathematical relationships that existed between particulate weight and the measured transmittance of gamma rays from an Americium-241 source. In the developmental phases, size distributions of three minerals (quartz, magnetite, and hematite) and a laboratory prepared two-mineral mixture of quartz and magnetite were accurately determined by the prototype system. In later stages of the investigation, semiconcentrates, an intermediate magnetic product from a taconite plant, were evaluated. Using 25-gram feed samples of this industrial material, the analyzer system was found to predict weight percentages for individual size fractions with an accuracy of ±0.85 percent or better at a 95-percent confidence level.

Jan 1, 1974

By D David

Amongst those whose task it is to design tumbling mills and other comminution machines there is an almost religious divide between devotees of the Bond method and devotees of other methods developed in more recent times. For a decade or so the issue was between the Bond power-based methods and the JKMRC (JK) simulation based approach. The newest method to challenge the status quo is power-based and was developed by Steve Morrell. As the title suggests, this paper will take some liberty at concluding that Fred Bond and Steve Morrell may be separated by history, but not by their approaches to their individual contributions to the science of comminution. Another driver for the paper is that although it is good to have diversity of thought, the existing divisions are problematic for those of us signing public disclosure documents. If alternative design methods produce materially different outcomes for the mill duty, then at least one of them is wrong or being used incorrectly. At some point the unsustainable argument may need to be put in a court of law that we metallurgists have two or more materially different design methods, each of which is correct! Therefore, perhaps a resolution is needed before this occurs?The works of both Fred Bond and Steve Morrell are each directly related to their contemporary grinding mill design and operational environments. Both their approaches are empirical, borne of observing and measuring real world situations. Both worked with theories that preceded them, gathered their own data and then each saw shortfalls in the status quo.Fred Bond was an escapee from revolution, a victim of The Great Depression, and had several near death experiences during his early site-based career. Perhaps he was fortuitously rescued from himself when asked by Allis Chalmers (A-C) to set up its rock testing laboratory in Milwaukie in 1930. Fred’s testing led him to conclude that neither the Kick nor the Von Rittinger theories explained his measurements. His writings on the failings of these old theories caused a divide between devotees of the old and new methods at that time. After many years, and much thought and plotting of data (the old way!), he came up with his now-famous equations (and his Third Theory) which have stood the test of time, certainly in the world of Bond-era machines.Coming from England via several African diamond mines, Steve Morrell immersed himself into the comminution world of the JK in Brisbane about a decade after Fred passed on. The JK had developed its semi-autogenous grinding (SAG) simulation framework using its own pendulum breakage tester, itself a derivative of the twin pendulum impact device invented by Bond decades earlier. At the JK Steve developed his authoritative Tumbling Mill Power equations and was involved in real world analysis of comminution problems on the global stage. Steve’s JK experience coincided with the demise of the rod mill, the rise of autogenous grinding (AG) and SAG milling and a rapid expansion in concentrator capacity.Morrell left the JK to pursue his own interests, which included ongoing consulting work, now demanded by the comminution world. He then turned to investigating a growing list of discrepancies between the opinions of designers and theoreticians, and the factual outcomes. The Morrell Method of design arose from this re-examination of ore testing, real world operating data and these glaring and expensive discrepancies between design and outcome. The elements necessary for a relook at the world of rock breakage were in place!CITATION:David, D, 2017. Steve and Fred would have been mates – a comminution design evolution story, in Proceedings MetPlant 2017, pp 2–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D. F. Ball, P. R. Dawson, J. T. Fitton

Report of discussion at December, 1970, IMM general meeting (Chairman: M. J. Cahalan, President) and contributed remarks on the paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C189-96, plus the authors' replies. Contributors included Cohen E., Hope B., Wasse D.G., Shakespeare A.G., Burwood D.S., Jones H.A., Dartnell J., Carter G.C., Henderson T.A., Relf G. and Clark S.W.

Dec 1, 1971

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998

By A Black, A de Jo, J Cavanagh, J Harding

Acidic and metal-rich waters have been discharging from Sullivan Mine, West Coast, New Zealand since the closure of the mine during the early- 1990s. This has resulted in a decrease in pH from a background of 4.5 to 2.8 and an increase in metallic elements in nearby Rapid Stream. In addition to the chemical effects on Rapid Stream, a study of freshwater macro-invertebrates revealed the absence of most biota downstream from the discharge. An attempt is being made to use the Sullivan Mine as a case study of problem and remediation analysis.

Jan 1, 2003

By James W. Echerd

Anthracite preparation developments, particularly in the early days of the anthracite industry, formed the basis for the modern coal preparation plants that have become so essential to the coal industry today. The anthracite industry, from early in the 19th century until relatively recently, was a leader in mining, preparation and marketing of coal, and played a leading role in the development of the industrial America we know today. Anthracite was discovered in America in about 1760--the story of Necho Allen is well known--but the rediscoveries leading to mining operations took place about 50 years later. The Wurtz brothers in 1815 at Scranton, the Smith brothers at Wilkes-Barre in 1807, Beach in Hazleton in about 1814, and Boyd in 1816 at Shamokin were all instrumental in promoting early mining and marketing of anthracite (J3. The early canals and railroads were built for the specific purpose of moving anthracite to the market areas. Eventually, the industry grew until, in 1917, it reached a production zenith of a little over 100,000,000 tons, representing about 20 percent of the total coal output in the United States. Almost half of the anthracite produced that year was consumed for domestic heating, a utilization that had dominated the industry for almost 100 years. Initially, anthracite had to be used by gunsmiths and blacksmiths, after which had followed the consumption of extensive quantities for railroads, blast furnaces and foundries, and electric power generation. Most of the markets have been lost to coke, oil, and natural gas. Near the anthracite regions, however, significant quantities are still used for domestic heating, power generation, carbon black manufacture, blending with bituminous coal to make metallurgical coke and fuel, and for other industrial purposes. Thus, anthracite production has not been entirely committed to history, but remains an active industry that follows modern practices in the mining, preparation, shipping, and utilization of a fuel that is still a valuable adjunct to the national economy. In fact, its inherent low sulfur content may make it an important fuel of the future. Estimates indicate there are reserves of anthracite to last for 300 years at a consumption rate of 50,000,000 tons/year. Anthracite Preparation Yesterday A 170-year history of the anthracite industry obviously is not the purpose of this discussion. A complete history of anthracite preparation, the rather unglamorous step in the processing of "mine run" hard coal to make it suitable for the user, is also not practical. Hence, the purpose of this report is to trace the development of some of the most important processes used through the years to meet a part of the demand for energy developed by our modern society. Anthracite preparation in the early days of the industry consisted solely of separating slate from the coal, by hand, underground (Z). This method prevailed for almost 20 years until wrought iron hand rakes were introduced to separate the large and small sizes. Shortly thereafter, the first attempts were made to size and clean the coal aboveground. The coal was dumped on a perforated cast iron plate, and men used sledge hammers to break the larger pieces into smaller sizes suitable for the market. The smallest sizes--that is, the material that went through the plate--were thrown away because they had no value at that time--a concept that existed for many years and actually was the basis for the subsequent "river" coal production and the many silt banks which are landmarks in the anthracite region. The larger sizes, at that time, sold for 50 cents per ton. The Batten breaker, or roll crusher, was invented in 1844, followed soon thereafter by the Snell-Diehm breaker (A). The latter had disadvantages, including excessive waste and fixed product size, but it later was improved in these respects. A breaker was also developed at Minersville, Pa., at about the same time that processed 200 tons of coal per day, using roll crushers and circular screens (1). Handpicking, from the beginning of anthracite preparation, was an important part of the cleaning process and was still being practiced as late as 1950. It was this process that involved the "breaker" boys of coal region lore. How much good handpicking accomplished depended on how much impurity was present in the coal--the more the impurities, the greater the reduction in ash. Thus, high-impurity streams were significantly improved, whereas picking of relatively clean coal was mainly to show an effort to make a quality product. As indicated, picking is largely a visual operation. It was and is wasteful of coal in the larger sizes since some good coal is always associated with the bad. However, it was probably much more effective' in the larger than the smaller sizes.

Jan 1, 1971

By D. K. Uko

In the stretch-bend or bending-under-tension test, a strip is rigidly clamped and restrained at each end and bent by central transverse loading using a radiused punch: The strip deflection at failure has been used as a measure of formability for high-strength low-alloy (HSLA) steels by other investigators. In this work, a detailed study is made of strains developing during stretch bending of an 80,000-lbf/ in 2 (552 MPa) yield stress steel using different punch radii. It is shown that toward the end of the process, the bending strains at both the inner and outer surfaces are tensile and suddenly increase at a rapid and approximately equal rate. The strain ratio in the failure region departs significantly from plane strain , even using a large width-to-thickness ratio of about 10. The effective fracture strains appear to be independent of bend ratio (punch radius/thickness) and significantly below the fracture s train in simple tension. Metallographic and tensile data were obtained for the subject material and, for one bend ratio, the effects on stretch-bend parameters of annealing both on this material and a. carbon steel were compared.

Jan 1, 1977