Search Documents

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

"The effects of five commercially available foaming reagents (range of 0 to 25 ppm) namely Dowfroth 250, Saponin, Yucca, Licorice and Meta-Para Cresol on acid mist control, current efficiency, polarization behavior, and deposit morphology and orientation were investigated. The deposition was carried out using a bench scale electrolysis apparatus (cell volume 3L) at 500 Nm-2 and 38°C for 3 hours from Kidd Creek zinc electrolyte. The acid mist control capability of the various reagents was studied and compared by characterizing the foam layer generated during actual electrowinning conditions and by direct quantitative measurements of acid mist levels on top of the electrowinning cells. Within the range considered, the addition of these reagents reduced the current efficiency, refined the grain size of the deposit, and changed to preferred orientation of most of the deposits. Among the reagents tested, acid mist measurements indicated that Licorice and Dowfroth 250 were the best acid mist suppressant at emissions of 0.30 mglm3 and 031 mg/m3 respectively while Yucca and MPC produced the most mist at 3.0 mg/m3 and 33 mg/m3 emission rates, respectively.IntroductionMost of the world's primary zinc is produced via a combined roast-Ieach-purificationelectrowinning process. Depending on the electrolysis conditions, several additives may be added to the electrolyte. Some (e.g. glue, antimony, sodium carbonate) are added to mainly counteract the detrimental effects caused by impurities while others (e.g. licorice, Saponin) are used as foaming reagents to prevent excessive acid mist formation. Acid mist emission is a problem in many electrolysis operations because it corrodes the equipment and is a health hazard to the workers in the tankhouse as well as it pollutes the environment. Due to recent trends towards more environmental protection and more stringent in-plant hygiene, there is an increasing need to minimize these aerosols. In order to eliminate or minimize these aerosols foaming agents are usually added to the electrolyte to produce a foam layer on top of the electrolyte, thus trapping most of the mist. The ideal foaming agent would trap all of the mist and would not interfere with the electrowinning process. It is also evident that the reagent toxicology, cost and availability are important factors that need to be considered.Review of the available literature clearly indicated that very little work has been done in the past on the subject of acid mist control in electrowinning operations particularly in the area of foaming and anti-misting properties of surfactants. Two papers [1,2] have reviewed briefly the existing technologies for acid mist control. Recently, most of the work in this area has focused on the development of special mechanical devices that could be attached to the electrodes and control the mist generation at the source before it is emitted to the cellhouse [2-5]. On the other hand, extensive body of literature exists that deals with the effects of anti-misting reagents on the electrowinning aspects [6-7]."

Jan 1, 1997

By B Olsson, B Reynolds, R Norman

An unprecedented growth in demand for coal exports has placed pressure on multi-user coal chains to guarantee that their capacity expansion projects will meet the required demand. These projects, however, are taking place in an increasingly complex commercial and technical environment - competing rail and coal terminal service providers as well as a myriad of competing mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing system complexity and integration has driven the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems, their sensitivity to uncertainty and the resultant capacity of the integrated system is the key to both maximising value and minimising risk.Recently, TSG has worked closely together with the Integrated Logistics Company and a number of key stakeholders in the Dalrymple Bay Coal Chain to develop independent system master plans. These master plans have provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. This paper provides an overview of the study and a comprehensive guide to the process required to effectively achieve valuable strategic insights in a challenging multi-user stakeholder environment.CITATION:Reynolds, B, Olsson, B and Norman, R, 2012. Using independent system simulation to mitigate risk in the Dalrymple Bay Coal Chain, in Proceedings Project Evaluation 2012 , pp 77-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By W. E. Stumpf

"SynopsisSouth Africa recently announced a resurgence in its commercial nuclear power programme. The implications for the development of the necessary high-level manpower within South Africa’s tertiary educational system and its national research and development (R&D) capacity in materials science and engineering, as well as in other engineering disciplines, are placed into perspective. An organized national process of developing this manpower by moving away from the previously high-risk and costly ’large programmes’ to rather a selection of ‘small and better’ research projects and a redefinition of what constitutes ‘nuclear materials’ are proposed as parts of this strategy.IntroductionSince 2008, and more particularly in 2014/2015, South Africa has woken up to the fact that significant steps need to be taken to ensure sufficient electricity generating capacity for the future, even beyond the coal-fired stations at Medupi and Kusile currently under construction. It is, therefore, encouraging to see some active large-scale wind farms in the Eastern Cape near Jeffrey’s Bay, in the Couga area, and others in the Western Cape already in operation. In addition, many solar energy projects are also progressing from the small localized scale to larger programmes in the Northern Cape, which may contribute some capacity on a national basis. South Africa needs to tap into its renewable resources of wind and solar much more, but will these projects solve the country’s long-term industrial needs? Unfortunately not. One cannot run mines and trains on solar cells. Industry needs reliable baseload capacity, and with very limited easily accessible hydrocapacity this leaves really only coal, possibly natural gas, and nuclear power as options. South Africa’s current over-reliance of about 90% on coal–fired power, however, places it in an internationally vulnerable position, and diversification into a more equitable energy mix should be a national priority for the medium to long term. South Africa cannot significant climate change confronting the human race, as the IPCC cautioned in 2013, and will have to adjust its future energy reliance to a more balanced combination of sources."

Jan 1, 2015

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By Mitchell P. Rothman

This paper concentrates on profits and other measures of return in the Canadian mining industry, especially in the non-mineral-fuels sector. The paper examines the historical patterns of mining profits, both before and after taxes, as compared with profits in other sectors of the Canadian economy, as well as some of the more important influences on mining profits. These include the prices of mineral products, provincial and federal tax policies with respect to mining , and the effect of inflation on mining profits and the financial position of mining firms - in each case, comparing mining with the other sectors of the economy. Finally, the paper provides an analysis of current and prospective rates of mining profits in relation to the capital required to ensure the future viability of the Canadian mining industry.

Jan 1, 1977

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By W. V. Bluck

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most any given power plant is now going beyond buying at the lowest delivered fuel cost and is now taking into consideration other factors such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1983

By Thirumalai, K.

Although the term "spalling" has long been known, Norton l first referred to its usage for the fracture or disintegration of materials subjected to rapid temperature changes. Spalling of ceramic materials at high temperatures has received attention in the past. Removal of the char formed during ablation in re-entry of space vehicles has been referred to as mechanical spalling. The first experiments to evaluate the process of rock fragmentation by thermal spalling were conducted by Stoces using a series of gasoline burners on the quartz veins of the Zinnwald deep mines in Germany. After the development of rocket-jet burners, the principles of 'thermal spalling combined with high fluid momentum found wide practical application in rocks. The well-known jet piercing process for drilling blastholes in taconite and for jet channeling in the quarrying of granite are among the more notable of these application^.

Jan 1, 1970

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By N. L. Richards

In manufacturing for the 21st century, the first company to market often leads the pack in product development and sales. In this respect, manufacturing processes play an important role in transforming “raw materials” into a product(s) for sale to a customer. Thus it can be seen that upfront modelling of a design concept, or modelling of manufacturing processes in a plant, can play an important role in effectively ensuring the overall design and manufacturing route is carried out in an expeditious manner. In the paper various scenarios are considered with respect to modelling the microstructure and/or process, in various manufacturing processes. Also considered are the effects of service condition on the manufactured product in terms of creep and fatigue.

Jan 1, 2010

By William E. Roscoe

"Non-producing mineral properties include those at various stages of exploration, properties at the pre-feasibility or feasibility stage, properties with currently uneconomic mineral resources, and past-producers. The market approach is applicable to all these types of non-producing mineral properties. Income approach methods such as discounted cash flow and option pricing are generally not applicable to properties at the exploration stage, but may be applicable to non-producing mineral properties with defined mineral reserves or mineral resources.The value of a non-producing mineral property depends on its perceived potential for the existence and discovery of an economic mineral deposit. The potential, in turn, depends on a number of factors which must be considered when choosing market comparables. These comparability factors include such items as geology, mineralization, stage of exploration and results, mineral resources, location and geography, and political jurisdiction. The date of the market comparables must be within a reasonable time period of the valuation date of the subject property. Although it is difficult to find good market comparables because of the unique nature of mineral properties and the small number of transactions, these difficulties are compensated for by analyzing a number of transactions on similar properties to develop a range of values for the subject property.For valuation purposes, market comparables can be expressed in terms of total property value, value per unit area (e.g., $ per hectare), or value per unit of metal contained in mineral resources (e.g., $ per ounce of gold, or $ per pound of copper). The market comparable value can be used to estimate the value of the subject property by using the total property value, unit area value or contained metal value."

Jan 1, 2003

By S Sims, A Stradl, G Hope, B Lacouture

Column flotation cells have been installed in numerous base metal operations around the world. The majority of these cells utilise conventional air-only spargers to introduce air into the bottom of the column. The recent development of instruments to measure the bubble characteristics in these columns has provided a renewed understanding of column behaviour. These new tools provided insight into why the columns at Red Dog Mine had never performed up to expectations. After efforts to optimise the spargers failed to substantially change the bubble size and air efficiency, alternate sparger systems were investigated. The Metso Minerals CISA Microcel sparger system appeared promising and was selected for a full-scale plant trial. The Microcel sparger system was originally developed for the coal industry at the Virginia Centre for Coal and Minerals Processing. In October 2003, a Microcel was retrofitted into one of two 3.66 m diameter flotation columns in the zinc retreat circuit at Red Dog Mine. The operation of the two different sparger systems in parallel allowed a detailed comparison. This paper discusses the performance of the Microcel based on the data collected during several detailed surveys. Bubble size measurements carried out in the pulp zone using the McGill University bubble viewer showed a significant difference in bubble size. The mean Sauter diameter of the bubbles decreased from 3.4 mm for the jetting-type sparger to 1.9 mm for the Microcel sparger. The overall recovery and the recovery by size fraction for both valuable and gangue minerals were compared. Paired t-tests demonstrated that the Microcel column produced a higher concentrate grade (0.6 per cent zinc absolute) and a higher unit recovery (2.8 per cent zinc absolute) than the existing Canadian Process Technologies Inc (CPT) SlamJet column. These improvements provided a payback period of 1.5 months for the $109 000 investment.

Jan 1, 2005

By T. P. Meloy

A methodology is presented for finding feasible or locally optimal designs in the class of homogeneous, countercurrent, processing networks performing two-component non-sharp separations. The advantage of the methodology developed here is that given a set of independent performance criteria (specifications such as network separation factor, beneficiation ratio or recovery), a feasible or locally optimal countercurrent network design meeting those criteria can be found in one step. In the methodology, graph-theory was used to explicitly obtain the exact network responses of specific countercurrent networks. These responses were used to formulate the linear recursion equations whose solution gives the expressions for the countercurrent network responses which are a function of the stage transfer functions for two-component, non-sharp separations. These expressions are also functions of the network variables n and c. These expressions, together with the set of independent design criteria, were solved simultaneously for n and c using the Levenberg-Marquardt algorithm for systems of constrained, non-linear equations. The network variables n and c embody the coded network design information which is used to find the feasible network design which satisfies the set of independent performance criteria.

Jan 1, 1994

By Gerald R. Larocque, Donald F. Grenville

"IN APRIL, 1965, the employee relations department (then called the personnel department) was established as a separate function within the company. Its aims and objectives were to hire an effective work force to operate the open-pit mine and the mill, which were at that time under development and construction. It was also directed to develop a sound policy for employee relations to assist the company in maintaining a stable and properly motivated work force, which included the establishment of satisfactory wage rates and fringe benefits, safety, fire protection and security. During the 8 years that the department has been in existence the scope of the company's operations has expanded to include a zinc plant and an underground mine. The work force has enlarged accordingly and now totals 1,680 employees working at the two sites, separated by 34 road miles. To cover the employee relations functions the department has a total of 29 members at the two sites. The department is organized under a superintendent, who has an employee relations supervisor, a safety director and a fire chief reporting directly to him. The employee relations supervisor, with 2 employment officers and 2 clerks, handles hiring, first-stage employee grievanoos, terminations, employee records, and the organization of company-sponsored functions and meetings. Safety, training and security are the responsibility of the safety director, who has 3 safety supervisors, 16 security men, 1 first-aid attendant and one hearing conservation technician to service the two sites. The fire chief operates as a one-man section responsible for plant-wide fire inspections and fireoriented training. Although"

Jan 1, 1974

By David S. Holmes

An overview of existing biological technologies for the recovery of copper and uranium is presented. Engineering and biological challenges and opportunities in these areas. are discussed. New opportunities for the biooxidation of refractory gold ore are described. Techniques for the development of new strains of microorganisms. for commercial metal recovery applications are discussed with special reference to the genetic manipulation for bacterial strain improvement.

Jan 1, 1991

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By Guy Reed, Russell Frith

"The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database.This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength “index.” These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of super-critical overburden behaviour as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases.A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.INTRODUCTIONThe inspiration for this paper is founded in three statements from two eminent persons in the field of coal pillar strength research, Jim Galvin and Essie Esterhuizen, as follows:Both Salamon and Munro and [the University of New South Wales] based the derivation of their pillar strength formulae on a criteria that the diameter of a panel of pillars, W, had to at least equal the depth of mining, H. This was thought to result in full tributary loading. It is now known that there are some mining environments included in both the South African and Australian databases in which mining span must exceed depth by a considerable margin in order to achieve full deadweight loading. Hence, it is logical to conclude that these data points may have contributed to pillar strength being overestimated by Salamon and Munro and UNSW (underline added by authors). Normally, this should be of no consequence because it is reflected in the probability of design success associated with any given safety factor (Galvin, 2006)."

Jan 1, 2018

By R. D. Carnahan, G. A. Stone, R. J. Arsenault

An experimental technique has been developed for carrying out a dynamic tensile stress-strain test in which plastic strain is measured continuously throughout the microstrain region extending through the macroflow region to total deformations of 5 pet. The tests were carried out on niobium, samples having interstitial impurity levels of 160 and -800 ppm at temperatures ranging from room temperature down to 100°K. A band spectrum of activation energies was obtained from calculations based on the measured activation volumes and temperature dependence of flow stress. The inability of a single rate-controlling process to predict such a phenomenon has led to the proposal that several sequential rate-controlling dislocation mechanisms are operative in the preyield micro-strain region. These are thought to be: the motion of geometrical kinks, the formation of double kinks in edges, and finally in the macrostrain region the formation of double kinks in screws. In less pure niobium the effect of interstitial impurities is shown to be dominant in the microstrain region, suggesting that a fourth probable mechanism is overcoming interstitial barriers instead of geometrical kink motion and the formation of double kinks in edge dislocations. THE principal fundamental aim of most mechanical properties studies of crystalline solids is to determine the dislocation mechanisms responsible for the plastic behavior. The extension of such studies to the region of preyield microstrain behavior has received renewed attention in the past few years as the details of macroscopic flow behavior have become better understood. For the most part, microstrain studies have been carried out using one of two variations of a single experimental technique.1 The first method involves loading the sample at a constant extension rate to a predetermined stress level (less than the macroscopic yield stress), instantaneously unloading, and then determining the extent of plastic deformation to a sensitivity of 10"6. The microscopic stress-strain curve is then constructed from the results of a repeated series of such individual measurements, each of which involves loading to an incrementally higher stress level, by relating the accumulated plastic microstrain for each step to the maximum applied stress in that step. The second variation, also carried out by step-wise increases in stress, measures the total strain to a sensitivity of ~10"6 and relates the maximum stress to the area of closed hysteresis loops that are generated under certain conditions (namely, prestrained samples). The foregoing methods have yielded interesting information about the nature of preyield deformation and plastic response to stresses below the yield stress, but they offer certain disadvantages for studying the dynamic behavior of dislocations. In the first method it is physically impossible to specify a plastic strain rate inasmuch as the test sample is reexposed, as it is loaded to its maximum stress in a particular step, to lower stresses at which flow will take place. The strain corresponding to a given stress level on the stress-microstrain curve thus generated will then always be greater than that at the corresponding stress level of a truly dynamic test carried out at the same extension rate. The second method has been used to obtain correlations with dynamic macroscopic flow parameters by applying dislocation damping theory to the hysteresis loop areas.2 The approach has had some success but suffers in that only samples that have been prestrained a few percent can be studied. Although the stresses

Jan 1, 1968

By G. X. Wang

The nonliving dried water hyacinth (E. crassipes (Mart.) Solms) roots were investigated for biosorption of cadmium and lead and other heavy metal ions in aqueous solutions. Dried water hyacinth roots, when suspended in solution, strongly and rapidly sorb several different metal ions. Factors such as reaction time, pH, initial concentration of metal ions, presence of other metal ions and biomass concentration were investigated. Metal ions, including Cd2+ and Pb2+, were bound to the root in a very pH-dependent manner, with the binding increasing after about pH 3. High levels of removal were obtained. The adsorption was shown to follow the generalized Langmuir adsorption equation. The relative affinity of the roots for lead is greater than for cadmium. The maximum sorptions of the roots were about 33 and 86 mg/g for cadmium and lead, respectively. Only 15-20 minutes were required for the process of uptake onto the biomass to occur. The batch sorption kinetics of the uptake of cadmium and lead can be described by an apparent first-order reversible reaction model. The roots could be regenerated after the metal ions were stripped. A solution of CaCl2 in acidic medium appeared to be the best eluant for desorbing the sequestered Cd and Pb completely at pH 3. The kinetics of the metal stripping process was quite rapid. Successful desorption of Cd and Pb from the biomass by acidic CaCl2 solutions revealed that the metal uptake phenomenon is reversible, implying physical sorption of Cd and Pb.

Jan 1, 1997

By B. W. Gandrud

This is the first report published by the Bureau of Mines on washability characteristics of coal from beds in Tennessee. It is based principally upon screen-sizing and float-and-sink tests of raw coal from a bed on the Cumberland Plateau. Stripping operations were undertaken recently on this bed by the Cumberland Collieries, Inc., near Chalybeate,Van Buren County, Tenn. The bed has not been definitely correlated, but it may be an extension of the Sewanee bed, which has been mined extensively in the Tracy City district to the south-vest and at points near Dunlap and Pikeville to the southeast and east. It was spoken of by officials of the Cumberland Collieries as the Sewanee bed at the time of sampling for this study. In a letter dated October 16, 1948, W. D. Hardeman, geologist of the Department of Conservation, Nashville, Tenn., states: "The stripping operations of the Cumberland Collieries near the old postoffice at Chalybeate are, I am fairly certain, in the upper part of the Whitwell shale, which carries the Sewanee coal. This coal may be a stray seam, but it probably can be correlated with the Sewanee coal, which is mined farther east. "There are no detailed geologic maps or reports covering the area, and this opinion is based on what was observed in visiting the strip mines in that general vicinity." The laboratory work upon which this report is based was done at the Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the Cumberland Collieries, Inc.

Jan 1, 1949