Search Documents

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By James R. Craig

The slags generated during gasification of petroleum coke are heterogeneous and con-sist of many different phases. These phases are important because their physical properties affect the operability of gasifiers and because they concentrate many elements that are present in the petroleum coke feed in only minor to trace quantities. An understanding of the chemistry and physical nature of these slag phases is necessary to predict behavior in the gasifier and in considering the ultimate use or disposal of the materials. Slags typically consist of silicate glasses, calcium-silicates, free iron-nickel metallic phases, iron sulfides, and aluminum oxide spinels enriched in iron, chromium, and vanadium. The partitioning of elements among these phases has been analyzed and will be discussed.

Jan 1, 1989

By Todd Kilduff, Paul Wilkinson

Microtunneling is rarely a straight forward “business as usual” endeavor. More often than not, these projects take twists and turns that require on the fly, out of the box solutions to get the project completed. This paper is a case history of a 63-inch diameter, Permalok, microtunneling project, extending nearly 700 linear feet under a hill forming the left-hand abutment to an earth embankment tailings dam. The job had three major and unexpected challenges that required unorthodox solutions. Challenge #1— Face Configuration: The Santiago Formation, a cemented sand formation with widely varying strengths, presented a challenge to configuring the face with regards to the number and length of pics and cutters. Subtle differences in type and size of the tooling had a big impact on the performance of the machine. Challenge #2—Eccentric Loading: Issues at the launch shaft with the Permalok pipe adaptors caused eccentric loading on the casing pipe. This issue resulted in overstressing and breaking of several pipe joints that ultimately led to seizure of the tunnel. Challenge #3—Back-tunnel Excavation and MTBM Recovery: There were many detailed considerations into excavating a recovery tunnel to retrieve the MTBM, especially being under a high hazard earth embankment dam.

Jun 13, 2021

By A. E. Landsberg, K. C. Corin, G. Stroebel, J. A. Miller, M. Becker, H. J. J. Gordon

Geometallurgy represents an integrated approach to mine planning and operation whereby the naturally occurring ore variability and its effects on all key downstream activities in the mine life cycle are considered. Process mineralogy is one of the key components of this integrated approach. This paper focuses on understanding some of the mineralogical variability across the Swartberg Cu-Pb-Zn sulfide ore in South Africa and its consequent effects on flotation performance. This process mineralogy project is motivated by the planned changeover and expansion of the Black Mountain Mines concentrator to process solely Swartberg ore compared to the run-of-mine blend currently being treated at the plant. Eight samples spanning the main lithological units of the ore body are described using quantitative mineral-textural data and bulk sulfide batch flotation performance to establish five process mineralogical or geometallurgical units comprising: quartz-pyroxmangite-magnetite, quartz-amphibolemagnetite, quartz-magnetite, garnet-magnetite-quartzite and mica-quartzite ores. Important mineralogical characteristics affecting Cu, Pb and Zn recovery, grade and selectivity specific to the different ore samples are discussed. Ultimately, the use of ore-specific process mineralogical and geometallurgical knowledge allows for better mine planning and plant optimisation. Keywords: Flotation, polymetallic base metal sulfide ore, process mineralogy, ore variability

Jan 1, 2020

By A Clarkson

Cannington Mine is an underground silver lead zinc operation located in north-west Queensland which has been in production since 1997. Ore is primarily moved through an underground material handling system comprised of a crusher, conveyor and hoisting shaft. The Fowler Shaft was constructed in 1997 using a strip and line method with the intent for it to provide a means to hoist ore from the loading station 600 m below surface. The shaft also serves as the route of key services including high voltage power, mine dewatering and fresh air. Despite the adherence to a mining exclusion zone, large-scale change in geotechnical conditions around the shaft were first observed in 2015. Ongoing ground movement around the shaft lead to cracking and delamination of the concrete liner. Shaft management required the on-site team to measure deformation rates and magnitudes, forecast change, manage rockfall risk and deforming pipework, and ultimately, hoisting skip clearance. Monitoring techniques to observe and measure deformation were required to evolve with the magnitude of movement. Some techniques leveraged off modern technology while some of the most useful techniques were based on logic and first principles. All shaft deformation management strategies relied on the co-operation and alignment between Cannington’s Infrastructure Maintenance, Survey and Geotechnical Departments.

Mar 29, 2023

By A. C. Fieldner

THE older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer, I who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter "g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 5, 1925

By W. A. Schaeffer, Sidney A. Justin, Jr. H. D. Easton

Restriction and proration of petroleum production have increased materially the difficulties attendant upon the estimation of reserves, particularly in large, "flush" fields. Such practices preclude the use of decline or other curves, from which, under capacity production conditions formerly prevalent, much could be learned as to the ultimate recovery to be expected from a given field or lcase therein. In restricted fields that would produce at many times the low rate allowed by the regulations in force if allowed to flow without restraint, one is forced to use other information than production performance to predict the volume of oil recoverable. Examples are: at Kettleman Hills, California; the Conroc, Van and East Texas fields, Texas; the Iowa field, Louisiana. It is beyond the scope of this paper to apply a definite method to the determination of the reserves in any actual field, therefore the discussion will be limited to a consideration of available methods and an enumeration of important factors governing the accuracy of such estimates. The problem is to determine not only oil in place but recoverable oil in place, for a given field or tract, which is complex and depends not only on the characteristics of the reservoir but also on the plan of development, the production allocation scheme, the rate of production and many other factors. Many data must necessarily be considered, weighed as to inportance, and assigned quantitative values. Estimates of recovery in prorated fields have been discussed by Brace', Shaw2, Snider3 and others. The wide difference in estimates of ultimate recovery from a number of important recently developed fields demonstrates the inadequacy of

Jan 1, 1935

By Noel W. Kirshenbaum

Difficulties and costs of transport markedly affect Canadian mineral producers because of distance from markets, weather conditions and rugged terrain. The chemical and physical nature of sulphide concentrates presents additional difficulties in handling and transport, resulting in higher costs which are ultimately borne by the mineowner. Troublesome properties include the thixo-tropic character of wet concentrates, freezing, susceptibility to autogenous heating, and fine particle size causing spillage and dusting losses. Canadian mineowners and shippers must contend with these problems and with stringent regulations governing the maritime shipping of concentrates. A "systems approach," in which complementary techniques in materials preparation, handling and transport are integrated, could reduce freight costs and losses for those selling concentrates, facilitate operations for those carrying and handling them and, in some cases, improve metallurgical processes in smelters receiving them.

Jan 1, 1969

By Brosnan J. G

Simcoa Operations is the only silicon smelter in the region and since the plant was commissioned in late-1989, has progressed from supplying silicon metal to the secondary aluminium market to the current position of supplying in excess of 90 per cent of its production to the high quality chemical and primary aluminium markets. This position has been achieved through the unique advantage which Simcoa has developed within the industry, namely raw materials, people and Simcoa's ability to adopt and use modern technology. A quality culture was instilled into the workforce prior to commissioning which ultimately led to AS3902 qualification in 1992. Simcoa has continued its quality drive through the formation of 'Simcoa's Quality Leadership Process' which is planned to make Simcoa the best silicon producer in the world.

Jan 1, 1995

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By Garth A. Maki, Douglas M. Smith

"The largest Canadian Lamella thickener installation to date, with 13,600 square feet of effective clarification area, is being successfully operated at the Rocanville Division of the Potash Corporation of Saskatchewan. This paper describes the operational principles and design features of the Lamella thickener, the testwork leading to its specification f or the Rocanville phase two expansion project and a review of the performance of the full- size unit which was ultimately installed.IntroductionThickening equipment operating in the Saskatchewan potash industry is generally situated within the main refinery building or a separate insulated an d he a ted structure due to the harsh winter climate and the need to closely control plant brine temperatures to en sure good flotation circuit performance Because these thickeners process large volumes of slurries, conventional basin-type designs tend to be large, ranging up to 46 metres in diameter or more. As part of the general effort to minimize capital costs, the potash industry has begun investigating the use of alternate high capacity, compact thickener designs. In this regard, PCS Rocanville undertook a program in 1978 to evaluate a LamellaTM thickener and one other type of ‘High Rate' thickener as alternatives to a conventional design for the phase two expansion project.This paper describes the operational principles and design features o f the Lamella thickener (manufactured by Axel Johnson lnc.), the testwork leading to the specification of a Lamella for the Rocanville expansion project and are view of the performance of the full size unit (1486 m2 of the effective settling area) which was ultimately installed and is now successfully operating in the Rocanville plant."

Jan 1, 1983

By K. Barron

"A computer program is described which will analyze the stability of coal pillars. The extent of the peripheral failed zone and the central elastic core of the pillar, the stress distribution across the pillar and its strength can be determined by a ""sliceby- slice"" analysis technique. The program incorporates a brittle/pseudo-ductile transition point so that a pillar may fail by brittle fracture or pseudo-ductile yield. It is shown that:(i) There is a minimum pillar stress below which fracture cannot initiate; hence there is a minimum pillar strength. (ii) In specific circumstances (narrow pillars) , once fracture initiates at the pillar edge it must propagate immediately to the pillar centre. This unstable situation is called ""catastrophic"" failure and might be regarded as a model of a pillar ""burst "". (iii) For wider pillars, the failed zone ex tends gradually into the pillar as the loading increases until it reaches the pillar centre when the pillar is deemed to have f ailed. This is called the point of ""ultimate"" failure.The critical pillar widths to avoid catastrophic and ultimate failure can be calculated.A hypothetical analysis of five rib pillars is given to illustrate the application and the results obtained from the model. The model is then used to analyze three case histories taken from the literature. The first demonstrates the applicability of the brittle/pseudo-ductile failure criteria for Pittsburgh coal. The second compares the pillar strength formulae derived here with those of Salamon and Munro(13) and Bieniawskiou . The final case history compares the model analysis with field stress measurements in a yielding pillar. In all cases the model results are compatible with the case histories."

Jan 1, 1984

By Jan Zwarcendyk

This study is primarily directed toward providing an understanding of the economic complexities associated with subsidence damage on the surface resulting from underground mining. Some of the pertinent theories on the physical stresses involved are reviewed, and both remedial measures and relevant laws in various countries are discussed. Part I (Chapters 1-3) is an historical overview of various aspects of subsidence problems (theoretical, remedial, and legal) during pre-World War I, between World Wars, and post-World War II, respectively. Part II (Chapters 4-9) presents a comprehensive analysis of the economic aspects of subsidence in relation to the following mining alternatives: (a) carrying out the lowest cost mining method without regard for any surface subsidence, (b) special mining techniques, (c) partial mining, (d) full recovery with stowing, and (e) sterilization or leaving the mineral unmined beneath selected areas. These alternatives are evaluated in terms of their measurable expenses.

Jan 1, 1971

By Georgc E. Collins

SEVERAL years ago, I estimated the total stock of gold in the world to be about a thousand million ounces, of which rather over one-third was available for monetary uses. Robert H. Ridgway has estimated the world's production from 1493 to 1927 as slightly over this amount. Of this total, 1.5 per cent was produced between 1493 and 1850 (before the Californian and Australian goldfields began to flood the world with gold), 331/2 per cent from 1851 to 1900, and 511/2 per cent from 1900 to 1927. Allowing for loss by attrition and permanent consumption in the arts, and for loss of buried treas¬ure, my first-mentioned estimate is perhaps not far from the truth; but my estimate of the monetary stock was certainly too low. Of the total production stated by Rid-way. 28 per cent came from North America. 26.9 per cent from Africa, 1.6.8 per cent from Australasia, 12.4 per cent from South America, and 11.2 per cent from Asia. Excepting that from the African conglomerate beds, the ultimate origin of which is still the subject of controversy, by far the greater part of the total production was derived from alluvials. Weighing all contingencies, it is improbable that any such production as has been made during the last forty years will be repeated in any similar period, if the present price level is maintained. The gold standard today seems firmly established except for temporary digressions. Nevertheless, no well-informed mining engineer will venture to assert the probability that the material for its maintenance throughout future generations can be furnished.

Jan 1, 1932

By D Drinkwater

In 2009, Peter Munro and Peter Tilyard examined the “human capital” in the mineral processing sector in a paper entitled Back to the Future (Munro and Tilyard, 2009). One of their major concerns was a general decline in technical skills and process knowledge, exacerbated by lack of appreciation of the impact this can have on process plant performance and, ultimately, profitability or sustainability of the industry. There are many reasons for this decline, not least of which are the work schedules of today’s metallurgists which have a very different balance between technical and non-technical responsibility than those in the past. However, a shift towards a more technical focus has potential to deliver a range of benefits for industry at large and for the individuals in it This paper discusses some options for development of core metallurgical and process engineering skills that can be used by graduates, employers and training providers.Key skills are identified and mapped against available opportunities for development, such as existing graduate programs, on-the job training and external courses. The authors also review a number of past and present high-quality graduate development programs, including the graduate development program in place at Mount Isa Mines in the 1980s and the Anglo Platinum Graduate Development Program (AGDP) currently operating in South Africa.

Aug 8, 2011

"The paper treats the spatial aspect of mine sequence optimization. This aspect is revealed in the context of determination of the optimum number of cutbacks of an open pit mine. Cutback mining is a dominating method currently in base\precious metal mining and it is based on a pseudo-economic discretization of the pit space by using advanced pit design algorithms. The result of the implementation of such approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks for maximization of the project value. A mathematical solution of this problem is developed with the utilization of a combinatorial analysis. The solution provides a multi-variant investigation of the optimum mine sequence with the implementation of an author’s method for production scheduling optimization, which uses the Net Present Value as a criterion for assessing the economic efficiency of mine sequencing. A case study is provided for the conditions of a hypothetical open pit gold mine to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the cutback geometry. INTRODUCTION The mine sequence optimization in open pit mining is a procedure that predetermines the efficiency of the production scheduling optimization. From a technological standpoint, the mine sequence optimization deals with two aspects – spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the open pit design problem. Original results on the time aspect of mine sequence optimization are published by Halatchev [2002]. They reveal a wide range of the Net Present Value (NPV) variation for a multi-variant arrangement of mine sequence over time and using a fixed geometry of the cutbacks, which determines the economic potential of a single open pit mine from a deterministic standpoint. The results show a range of NPV variation up to 30% depending on the stripping ratio of the mine. The effect of this variation is mainly due to the implementation of the mine planning principle of waste deferment in the scheduling optimization and using all theoretically possible variants of mine sequence arrangement by the inclusion of the bench sequences over the Life-Of-Mine (LOM) in the production process."

Jan 1, 2015

By I. M. Marshall

A review of technical literature covering Canadian mining emphasizes the advancement and changes that have been made in mining practice. However, current technical publications rarely outline basic principles or state definite rules that govern profitable mine operation. it may be argued that the broad principles of mining have long a go been outlined in various handbooks, text-books, and periodicals, and that these principles never alter. This is in great part true, but modern machinery, improved meta1-lurgical practice, and other advances, have in part modified these principles or changed the manner of their application. Many engineers hesitate to state specific rules, because it is so easy to quote an exception to a rules that any such statement appears to lose weight upon its very utterance. The exception to rules, and the reluctance to formulate rules, has forced such maxims as "the only rule in mining is the point of a pick," and "gold is where you find it". As an illustration of rules and their exceptions, one might quote the time-honoured maxim that a mill should not be built before a shaft has been sunk on a property in point of fact, Canadian mining history is replete with examples of wasted capital where a mill was built before a shaft had been bottomed. Y et this past year has seen a property enter profitable production whereon the building of the mill was started before the shaft was sunk. Instances such as this should not be accepted as evidence that a rule has been overthrown, but rather as an exception to the rule. The case cited pays tribute to the application of the diamond-drill combined with the correlation of sound geology. Incidentally, both these features emphasize a modern trend in the development of Canadian mining properties-a trend that is perhaps worthy of further comment. It is such trends that affect the principles of mining or modify their application. It is with such that this paper deals, at ]east in part. It is hoped that the statement of principles and the opinions herein outlined will be of sufficient interest to arouse discussion.

Jan 1, 1939

By G. Kleyn

"Sub-standard practices and their adverse impact on safety performance remain a challenge in the South African gold mining industry. The purpose of this study was to investigate the root causes of sub-standard practices and the effect on safety performance in South African gold mines. The focus of the study was on the underground production operations at a gold mine in the Free State. The study consisted of three parts: a personal investigation into the causes of sub-standard practices at the mine, a comparison with the results of a cultural study performed at the West Wits mines, and a behavioural survey.The studies described in this article yielded similar results in terms of the key drivers behind sub-standard practices. It was found that substandard practices had a number of causes, and the origin lies within the habits, attitude, and behaviour of employees. Current methods of addressing sub-standard practices and improving safety performance were found to discourage employees from performing work safely and according to procedure. It was concluded that the lack of critical behavioural habits for the given work environment and job title could possibly be the primary reason for the occurrence of sub-standard practices. IntroductionSince the implementation of the Mine Health and Safety Act, 1996 (Act 29 of 1996) and the Mine Health and Safety Regulations, the South African mining industry has been striving to improve health and safety performance and has placed great emphasis on adherence to mine standards.The Act requires employers in the mining industry to report accidents, incidents, and dangerous situations to the Regional Principal Inspector of Mines in their area. The data provided by employers is captured and analysed by the South African Mines Reportable Accident Statistical System (SAMRASS) and made available for public viewing (Department of Mineral Resources, 2011).A review of the national mine-related accident statistics shows clearly that the South African gold mining industry has improved its safety performance markedly over the past decade, but is still facing major challenges (Figure 1). These include meeting the Mine Health and Safety Milestones (Department of Mineral Resources, 2011)."

Jan 1, 2016

By Friedel. Michael J.

The U.S. Bureau of Mines investigated acoustic emission (AE) and the Kaiser effect in six types of rock: St. Cloud gray granodiorite, Barre granite, Dresser basalt, Salem limestone, Berea sandstone, and a volcanic tuff. AE signatures were used for interpreting the rock deformation stage and for indicating mechanisms of failure in uniaxial compression. The research demonstrated the advantages of using the volumetric stress-strain curve, as opposed to the more conventional uniaxial curve, for correlating AE response signatures with deformation stages and fracture processes in the rock. Standardized experimental procedures were used for the AE monitoring. The Kaiser effect was shown to be capable of determining prestress levels to within a few percentage points in uniaxial compression tests. Also, prestress memory was shown to be retained in the rock for periods of up to at least. 5 months, the maximum period of testing. The Kaiser effect AE technology holds promise for providing a comparatively inexpensive and less complex method for examihing stress history in rock. However, since the conftning stress has a pronounced influence on the Kaiser effect, it must be considered in developing technology for determining peak fteld stresses based on the Kaiser effect.

Jan 1, 1990

By Philippe Angers

This article analyzes the social acceptability process of a mining project located in an existing city. It will explore how the principles of sustainable development have been integrated in the project of the Canadian Malartic open pit mine held by the Osisko Mining Corporation, and the corporate social responsibility (CSR) initiatives proposed to strengthen the social acceptability of the project. This mine is located on the ancient south quarter of Malartic and has required the displacement of hundred of houses and five institutions. The location and the inherent social impacts generated by the relocation of the citizens of the south quarter makes this case particularly interesting to understand social dynamics in an era of environmental consciousness. These major constraints of the mine generate high expectations within the urban population with regard to the social and economic benefits it will receive from the project. In a context where society demands higher CSR from the corporation, Osisko is closely followed regarding their actions toward the sustainable development principles to see if they respect the environment and the desires of the community. From the beginning, the company had to be a model of sustainable development in various aspects reflected by the manifold interest of the population. To understand the endeavor made by the company to fulfill the demand of CSR, we will analyze how the company understood sustainable development principles and what CSR initiatives Osisko company put forward. We will explore the involvement of the company in various social aspects like employment, employee satisfaction, and the level of commitment to non-discrimination policy in employment, notably with the native populations. We will also take a closer look at the relationship built by the company with the community and the level of commitment with the various stakeholders of the community. In this way, we will be able to seize the level of involvement of the company in the fulfillment of the principles of sustainable development toward a higher CSR, and to specify the trajectory adopted to build social acceptance.

Aug 1, 2013