Search Documents

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Elaine Ellingham, Francis T. Manns

"Abstract -The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at0.156 oz/TAu . The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distribution s, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By J. C. Watts

Monitoring and control of conventional industrial wet grinding circuits is conceptually straightforward. However, since production objectives and operating constraints can vary widely from plant to plant, there is probably no single overall grinding circuit control strategy which is "best" in all cases; in-variably some compromise is necessary between performance desired under ideal conditions and performance achievable in practice. The recent advent of relatively low cost, reliable, high speed small computer systems is revolutionizing daily operations in increasing numbers of metallurgical processing plants. Of special power and capability is a hierarchical computer network like that currently in use at the Pinto Valley Operations of the Cities Service Company. Several satellite processors for key plant areas communicate with a master computer operating under a powerful multitasking real-time operating system. Hardware and software structure is such that downtime on one of the processors -including the master -does not have a major impact on overall system operation. Admittedly, the powerful, core efficient table driven satellite software, which handles process/computer communication, calculation of nonmeasured process variables, and basic Direct Digital Control functions, is difficult to modify. However, important high level process monitoring, report preparation, graphic display, and supervisory control functions -including economic optimization -can be implemented by project engineers at the plant site. Thus, for example, new control strategies can be quickly examined and rapidly evaluated. Such computer monitoring capability also permits use of short duration process pulse tests for approximate dynamic modeling and rapid calculation of controller tuning constants for single loop dominant systems. Following a brief back-ground discussion of the Pinto Valley Project, we present some of the more interesting results and conclusions of our work over the past year.

Jan 1, 1978

By John Sasadi

Several years ago I wrote a comprehensive paper 'entitled, "Future Trend of Bulk Carriers" dealing with the principle dimensions of vessels and how they can be predicted; then with loading and unloading of large carriers, especially considering various designs of "Self Unloaders". Since writing the paper, many large bulk carriers were basically built along the, predictions made. Maximum size today is in the 150,000 DWT class, with few exceptions, which are combination carriers (ore-oil) or OBO's (oil-bulk-ore) in the 200-250,000 DWT class in the same paper, many references were made cautioning engineers not to design ports which could be "obsolete tomorrow", however, these were not always followed. Nevertheless, during the past few years many modern ports were built signaling the beginning of a new area of "Super Ports". Super Ports can be built for various reasons, most important to provide transfer stations where bulk material is received from large carriers then transferred to smaller vessels or barges for distribution. Obviously, opposite movement of bulk commodities can justify the building of "Super Ports", however, these are not as difficult to build for many reasons. The Material Handling Industry has developed efficient means of unloading smaller vessels or barges with continuous-type unloaders and has mastered the art of storing, reclaiming, and moving large quantities of bulk material to high-capacity shiploaders. Nevertheless, the industry has failed to design and market efficient ship unloaders which in any way could match the presently attainable shiploading rates. For these reasons, it is considerably more difficult to build "Super Ports" for incoming rather than outgoing bulk materials with large bulk carriers. The purpose of this paper is to elaborate on problems affecting high-capacity, continuous ship unloaders, especially involving large bulk carriers. For better understanding, some references will be made to the smaller, continuous barge or ship unloaders, but only as the principles affect the larger units. Additional references will also be made to exploit the present "State-of-Art" of the grab

Jan 1, 1972

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By A R. Bye

The mining industry is facing some key challenges that provide a compelling case for geometallurgy initiatives. Over the last 30 years, the average grade of Australian orebodies being mined has halved while the waste removed to access the minerals has more than doubled. In the last eight years, the industry’s energy consumption has increased 70 per cent while multi-factored productivity has fallen 24 per cent. The paper documents a broad range of industry case studies which demonstrate strategies for gaining value from geometallurgy.The mining industry constantly faces the key questions of how significant ore variability is on mine valuation and how would knowledge of the variability change the mining schedule, mine to mill design and operation. Using case studies the paper describes the methods used for incorporating mineral extraction attributes into orebody models and their technical integration into daily operation as well as mine planning optimisation. While pit optimisation from a fully attributed geometallurgical model highlights areas of opportunity and risk it is shown that during the scheduling phase of mine planning that significant value can be added. The benefits from these projects included reducing geotechnical and environmental risk, improving mine to mill performance, option analysis and quantified cash flow risk. There is growing acceptance within the minerals industry that ‘realistically assumed modifying factors’ defined by a competent person/s are not sufficient to mitigate the risk of funding mining ventures. Geometallurgy is moving away from factored ore reserves to data-rich block models providing reliable information for mining, metallurgical and environmental considerations.

Sep 5, 2011

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By Eugene V. Cilento, R. Clark Lantz, K. A. DiGregorio

"This laboratory bas developed a sensitive electro-optical method to quantify the initial rate (R) and total amount (MAX) of superoxide (02) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope-based TV system to visualize PAM in culture, and to video record the images during the time the cells produce 02. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of O2-, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin . were added to the medium (in vitro). Rand MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using which will permit PAM to be restirnulated by different dusts to help establish a dose response relation~ p and a means to study the role of lung surfactant on modifying the acute toxicity of inbaled dusts. Ultimately, this methodology should provide useful insight into establishing the role of 02 in PAM dysfunction due to inhalation of dusts, and in lung diseases such as pneumoconioses. INTRODOCTIONPAM are free cells found in the lungs which protect the lungs by removing foreign debris and bacteria. This is accomplished, in part, by the process of phagocytosis, whereby foreign matter is internalized into vesicles known as primary phagosomes. Phagocytosis also involves the chemical breakdown of inhaled dusts and the killing of microbes. Detoxification is aided by the respiratory burst, which is a metabolic response of the cell to foreign substances, that results in the production of highly reactive oxidizing agents from the partial reduction of extracellular oxygen to superoxide (02) at the surface of the plasma membrane. Superoxide undergoes either spontaneous or enzyme catalyzed dismutation reactions to form hydrogen peroxide (H202) and subsequently hydroxyl radical (OH•) and singlet oxygen (02 t ). However, while these oxygen metabolites aid in the killing of microbes they also may destroy endogenous tissue. For example, 02 has been linked to the aging process and to many diseases including emphysema, diabetes, and cancer.'' Therefore, a better understanding of the production of 02 is extremely important since an abnonnally low production could result in damage by inhaled dusts and bacteria while an abnormally high production could result in direct damage to the lung tissue by the phagocytes. Inhalation of respirable sized mineral dusts, such as quartz (silica), coal mine dusts (CMD), and asbestos, results in various pulmonary disorders. PAM are thought to play an important role since evidence suggests that the first step in fibrogenesis is an interaction of dust particles with PAM. Generally, in vivo exposure of animals to mineral dusts results in increased respiratory burst activity, migratory patterns, phagocytic behavior, and secretory potential of PAM, and for this reason these have been implicated to be pivotal events in the pathogenesis of pulmonary diseases.1 In addition to stimulation of resident PAM, an influx of monocytes into the lung and/or production of new macrophages generally occurs in response to fibrogenic dust inhalation. Further, PAM may attract and stimulate fibroblasts, which normally synthesize proteins and collagen during rep~ of tissue, by secreting chemoattractants and enzymes. Thus, PAM may be involved in pulmonary disorders through failure or partial loss of their defensive capability, or indirectly, through release of other mediators."

Jan 1, 1990

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Brandon Smith, William Bohlen

Riverbank erosion along the Brazos River has modified the structural support conditions for an existing bridge structure in Southeast Texas. The 8-span, 1,200-foot long bridge was completed in 1992 along Highway 99, a key corridor for the Houston area. Foundation support conditions have been altered due to natural, ongoing river morphology for three bents on the affected riverbank. Recent events include three storms within a three-year period that each exceeded the 500-year return probability. This resulted in accelerated erosion along the northern riverbank. Over forty vertical feet of soil has been removed in some locations. Drilled shaft foundations are now functioning as columns. This review considers the behavior of columns and deep foundation elements due to the modified support conditions. The review ultimately presents a rational methodology for the review of the present and anticipated future bridge configuration with respect to current strength, service, and extreme event limits, with corresponding safety factors for the design. Introduction and Background The Fort Bend Grand Parkway Toll Road Authority (Owner) oversees the State Highway 99 Judge Jodie Stavinoha Bridge over the Brazos River. The 8-span, 1,200-foot long bridge was originally designed with four southern approach spans of 115 feet; a three-span continuous river crossing with span lengths of 195 feet-235 feet-195 feet; and a single northern approach span of 115 feet. Figure 1 provides an overview of the northern portion of the bridge. Table 1 provides a summary of the original bridge substructure configuration. When the bridge was completed, the centerline of the Brazos River was located at midpsan of the main span and the northern high bank was originally located at Bent 7. Erosion process has forced the northern high bank to Abutment 9 (also called Bent 9), and the river centerline during normal flow conditions is located south of Bent 8. The overall estimated river excursion at present day is approximately 270 feet to the north from its original location. An erosion wall that was installed in 2017 limits further erosion of the north river bank within the 300-foot width of the roadway corridor right-of-way. This study was developed to better understand the existing conditions, and to forecast the need, nature, and criteria for potential future improvements.

Jan 1, 2019

By R Baumgartner

The Canahuire deposit is a recently discovered Au-Cu-Ag epithermal deposit in Southern Peru. A geometallurgy program is a key study element of the project Feasibility study. Metallurgical, mineralogical, and comminution studies have been completed over a suite of samples, spatially distributed among the various geological/ore domains. The early stage of Canahuire presents challenges as there is a lack of metallurgical information to guide geometallurgical sampling, in contrast with an established deposit at a more advanced stage of development or mining. Nevertheless, the available information will assist in the development of geometallurgical domains for Canahuire in order to ensure that future metallurgical, mineralogical, and comminution test work is representative of the deposit variability. This supplementary knowledge will be able to predict important metallurgical parameters which will be incorporated into a geometallurgical model to spatial predict material types, metallurgical recovery and through put. The information obtained will be a valuable addition to the future mine plan, influencing process design, engineering design, plant operation, operating and capital costs, and ultimately will reduce project development risk.

Sep 5, 2011

By Matthew Preedy, Brett Campbell, Jim Rush, Alan Howard, Derek Penrice

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2018

By E Vargas, A Egana, M Alarcon, X Emery, A Barberan, A Lopez, N Morales, C Friedrich

"As the cost in time and money of data from sensors and small-scale tests has reduced, additional challenges have arisen. Although many mine data sets are not big relative to those in other disciplines, they are complex in other ways, and becoming too large to manage efficiently on personal computers. In order to take advantage of the opportunity offered by increased data, a diverse team from Universidad de Chile and CSIRO Mineral Resources has developed a virtual geometallurgical laboratory to support the computational requirements linking data acquisition with data-driven business decisions. A particular focus to date has been the development of user-guided workflow ensembles to enable comparison between plausible geometallurgical hypotheses.A case study has been undertaken using publicly available data from the Rocklea Dome iron deposit in Western Australia. A hypothetical mining schedule was produced from geochemical and hyperspectral drill core/chips data via the following steps: data preprocessing, exploratory data analysis, geochemical interpolation, block modelling, ultimate open pit design and scheduling. The key outcome of this study was the integration of workflow stages through new plug-in methods or modification of existing software. Outcomes from this study will be described in the paper in terms of geological and metallurgical data quality, analytical software support and ongoing computing infrastructure requirements.CITATION:Lopez, A, Barberan, A, Alarcon, M, Vargas, E, Ortiz, J, Morales, N, Emery, X, Egana, A, McFarlane, A and Friedrich, C, 2016. Progress towards Data-driven Mine Planning via a Virtual Geometallurgical Laboratory, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By John Barber

The Deep Ore Zone (DOZ) Mine is PT Freeport Indonesia&apos;s (PTFI) newest operation. Production at the mine began in September 2000. The DOZ Mine produces 25 kt/d (27,500 stpd) using mechanized block cave mining methods. The DOZ Mine has several major improvements when compared with previous block cave mines in the district. It has an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system. PTFI&apos;s copper and gold mining complex is located in the Ertsberg mining district in Irian Jaya, Indonesia (Fig. 1). The Ertsberg district is located in the Sudirman Mountains at elevations from 3,000 to 4,500 m (9,800 to 14,700 ft) above sea level. The topography is extremely rugged and rainfall in the mine area averages 3,000 mm/a (118 in./year). Freeport began production in the district in 1972 when the mill began processing ore from the Ertsberg openpit. Underground mining began in 1980 when the Gunung Bijih Timur-Ertsberg East (GBT) Mine was brought online using block caving methods. In 1991, the GBT Mine reached a maximum production rate of 28 kt/d (31,000 stpd). Ore from the mine was exhausted in 1994. The Intermediate Ore Zone (IOZ) was brought into production in 1994. It, too, used block caving methods and had a design rate of 10 kt/d (11,000 stpd). The IOZ is currently producing at a rate of 21 kt/ d (23,000 stpd). The DOZ was discovered in the mid-1980s by deep drilling from the GBT. The GBT, IOZ and DOZ deposits are all situated in the Ertsberg East Skarn System (EESS). In 1993, the first of several studies was completed that indicated that portions of the DOZ Mine could be economically mined using block caving methods. Limited development was started in 1995. Full-scale development and construction began in late 1997. The crusher and conveying system began operating during the first quarter 2000. The first of two main exhaust shafts has been com¬missioned, along with three of the four new main fans. The second exhaust shaft and fourth main fan will be in service by the end of 2001. Undercutting and production began in September 2000. The DOZ Mine will reach its design production rate of 25 kt/d (27,500 stpd) in 2003. A study is under way to determine if an ultimate production rate of 35 kt/d (38,500 stpd) is feasible.

Jan 1, 2001

By R. Simon, A. Khosravi

"Tensile strength of rock samples is measured by direct and indirect tensile tests in accordance with standard guidelines. Due to the difficulties in performing direct tensile test, the indirect tensile (Brazilian) test is conventionally carried out to obtain the ultimate tensile strength. A limited number of studies have been conducted to investigate the role of sample size (length to diameter ratio = L/D) in the stress distribution of the Brazilian test using numerical and analytical methods. These investigations showed that the tensile stress distribution along the loading diameter is not uniform. They also indicated that the difference between the tensile stress at the middle part and at the sides of the sample with higher L/D ratio is greater than that in the other samples.The objective of this study is to show the effect of tensile stress distribution on the fracture surface created by the Brazilian test from a morphological point of view on the samples with different L/D ratio. Hence, a series of fracture surfaces created using the Brazilian tests on the rock samples with L/D of 0.5, 0.75, 1, 1.25 and 1.5 were investigated.In this study, all fracture surfaces were scanned by a 3D laser profilommeter. A number of roughness profiles parallel and perpendicular to loading axis have been selected from the samples with different L/D ratio and spacing of 1 mm. The results show that the roughness of the profiles perpendicular to the loading axis increases with an increase of L/D ratio, while the roughness of the profiles parallel to the loading axis decreases. Furthermore, some roughness profiles parallel to the loading axis were chosen and divided into three segments. The results revealed that the segment in adjacent to the upper loading platen possesses higher roughness than the other segments."

Jan 1, 2015

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013