Search Documents

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By R. C. Adams

This report describes the feasibility of mining the oil shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976

By A. W. Ambrose

The output or oil and gas rrom the producing fields in the United States is rapidly deelining. Coincident with this decline is a steadily increasing demand ror petroleum and its products, but at present there are no commercial substitutes ror gasoline and lubricating oil. Undoubtedly, many new fields will be discovered in this country during the next rew years. Indeed, there may be periods or temporary flush production that ror a rew months or a year or perhaps two years will afford a surplus. Such peaks are temporary and should not be given too much weight in considering the relation between petroleum supply and our national lire. In considering this problem we must regard a long period or time, and, ir we do that we shall see that domestic production will be unable to keep pace with consumption. Hence, the public good demands t~at the highest efficiency obtainable be practiced in the production or oil. To accomplish this end, the operator or to-day should so organize his rorces ror development and production that he recovers every barrel or oil that can be recovered at a profit. This necessarily involves the use or eeonomical and scientific methods or development a:nd production and the elimination or waste. The Bureau or Mines has ror years urged the conservation or petroleum and its products, and has pointed out that -such conservation should start before the oil is brought to the surface rather than arter it is in storage tanks. Losses or petroleum underground have undoubtedly been rar greater than losses in storage, in transportation, and in refining. The quantity lost usually is indeterminate, and hence difficult to express in terms or money, but by remembering that entire oil fields have been ruined by invadIng waters some idea may be gained or the importance or underground waste. The petroleum engineer is coming to be recognized as an extremely important aid in the intelligent development or oil fields. In this paper an effort is made to outline ror the engineer and producer a field or work whereby science and engineering not only can but have been applied practically. The mining engineer has been the direct- ing hand in the development of mines, and it is being recognized more and more that the petroleum engineer has a similar function in developing oil properties. Thispaper aims to show the general method of procedure in studying underground conditions in producing oil fields and how such study may not only correct but even prevent great unnecessary losses. Such work provides the company with maximum insurance for the field against loss and is accompliphed at minimum cost and minimum risk. Throughout the paper reference is made to oil wells and oil fields, but to a certain degree many of the suggestions relating to oil wells are applicable in the care and protection of gas wells and in solving gas problems.

Jan 1, 1921

By J. Bilant, J. Donnelly

"A spatially-discretized heap leach simulation model was developed within the GoldSimTM modeling framework for the Coeur Rochester Mine, Nevada. The model is being evaluated by Rochester as a means of improving forecasting of silver and gold production on an actively loaded valley fill heap leach facility. Optimization of future heap leach operations and crusher product size is also being evaluated with this software. Simulation modeling incorporates metallurgical data such as mine planning, particle size distribution of placed ore, stacking plans, pad geometry, and leaching dynamics. The heap leach model is represented as a discretized matrix with lifts providing vertical separation to form 19,840 spatially discrete cells. Each cell is quantified with regard to ore properties and metal content. The model tracks solution and cyanide-complexed silver and gold within each cell as a function of time based on pad operations, unsaturated flow properties, and kinetic rates. Practical heap leach management and daily operation will be discussed as it relates to the simulation and forecasting model. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities, is an open-pit silver and gold mine located in Pershing County, Nevada. In 2015 Rochester produced approximately 4.6M troy oz silver (Ag) and 52K troy oz gold (Au) through combined cyanide heap leaching of the Stage II, III and IV heap leach pads with recovery via a Merrill Crowe process plant. Rochester is actively stacking and leaching ore on the Stage III Heap Leach Pad. The Stage III pad contains approximately 70M tons of ore in a valley fill configuration and is forecasted to receive an additional 20M tons of ore by the life-of-pad in 2019. The ultimate height of the pad is permitted to be 400 ft above the liner and solution collection system. Approximately 80 percent of the ore loaded on the Stage III pad is produced from tertiary crushing split from two crushing circuits that produce a nominal 80 percent passing 3/8” product. The remaining material consists of run-of-mine (ROM) from off loads of re-mined waste rock stockpiles. Metallurgical testing of the ore indicates low variability in geologic properties and high variability of both Ag and Au extraction rates for the various particle size distributions. Historically the valley fill configuration provided metal forecasting challenges that could not be predicted as the leach pads grew. Forecasting metal production and leach optimization of the Stage III pad became challenging due to the extreme variation in heap leach pad depth, application of available barren leach solution and the variability of Ag and Au extraction rates for the various ore particle size distributions. To assist with understanding and optimizing metal production forecasting with these factors for the Stage III pad, Hatch developed a spatially-discretized heap leach simulation model using GoldsimTM dynamic simulation software. The model incorporates metallurgical data such as mine planning (tonnages and grade), particle size distribution, ore crushing, ore stacking plan, pad geometry, and both leaching dynamics and kinetics to forecast metal production from a consolidated mine plan."

Jan 1, 2017

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By Ausenco Engineering Canada

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.INTRODUCTIONComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semiautogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2016

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By Megan Badonie, Devlon Shaver, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Critical minerals are becoming more important in our technological society because they are used in many of our electronic devices, batteries, and magnets. In New Mexico, low to moderate concentrations of critical minerals are found in Late Cretaceous coal and related strata in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, REE, and Critical Minerals) program. The New Mexico coal, humate, and clinker deposits are relatively low in REE (<325 ppm TREE), Li (<90 ppm), V (<168 ppm), Co (<51 ppm), Ni (<108 ppm), Zr (<557 ppm), and many other critical minerals compared to normal economic deposits. Some of these rocks are enriched in Al2O3 (<40%) and Sr (<3740 ppm), both critical minerals. Common minerals hosting the critical minerals in these rocks include clay minerals, zircon, and rutile/anatase. As the demand for some of these elements increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Ultimately, economic potential will most likely depend upon production of more than one commodity, maybe even from coal, humate, and clinker deposits.

Feb 1, 2024

By G. Harper

The Windy Craggy polymetallic massive sulphide deposit is located in the extreme northwest corner of British Columbia 40 miles west of the Haines Highway, 90 miles northwest of the port of Haines Alaska. The physical setting is mountainous country but with few peaks rising above 2,000 metres elevation, in contrast to the spectacular mountainous terrain to the north and south in Kluane and Glacier Bay Parks respectively. Valleys are classically U-shaped with incised V-shaped bottoms. The upper portions are still occupied by glaciers, which in the Windy Craggy area are documented as retreating at a rapid rate -in the case of the Tats Glacier of the order of 1% of its mass per year. The outcrops around Windy Craggy show a north-easterly dipping sequence of Mesozoic limey sediments and volcanics being the western limb of a north northwesterly trending syncline. Northeasterly cross folding provides a few complications. The flanks of the syncline have been buttressed by intrusive bodies of granitic affinity.

Jan 1, 1991

By R. D. Williams

INTRODUCTION In a very real sense, Butte, Montana is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site. One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot Smelter operated from 1881 to 1910 moving Upper Silver Bow Creek to the south and depositing approximately 370,000 cubic yards of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot Tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 224,000 cubic yards of contaminated material. As part of the Superfund remedy, EPA proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place which set the stage for a series of studies which continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. HISTORY OF THE PARROTT MINE AND TAILINGS Placer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery lead to a stampede of placer and lode claims. One of the first lode claims located was the “Parrot” lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow and it wasn’t until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine! The Parrott mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the District’s rich copper ore. In 1885 the employees of the Parrot Smelter bought the Butte Reduction Works, another smelter. In 1885 dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Figure 1).

Jan 1, 2019

By S. M. Robinson

Wollastonite is recognized as one of the most unique, non-metallic minerals in the world. Its history for use in industrial applications is recent compared to other minerals, however, its distinctive physical properties, such as acicular particle shape, and alkaline pH creates incorporation possibilities ranging from bowling balls to automotive fascia, from ceramic tiles to automotive brakes, and from thermal insulation board to industrial and trade sale coatings. Its future use will be impacted by the exploitation of deposits which will ensure maintenance of the acicularity and purity of this naturally occurring mineral. Additionally, closely held surface treatment technology will open up additional niches requiring highly engineered performance.

Jan 1, 1995

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF&apos;s. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By R. G. Knickerbocker

A STURDY and consistent expansion of the metal industry occurred in 1947 exemplified by an increase of approximately 30 per cent in steel consumption over 1946. For this major reason, ferroalloy metals have seen their most useful and important peace-time year. The current domestic rate of consumption of high-grade ferroalloy ores, together with added consumption of new foreign producers as well as for eign nationals&apos; restrictions on high-grade exports, makes very evident the increasing difficulties of obtaining sufficient high-grade ores. This accentuates the need for new and less expensive methods of production of ferro-alloy metals of higher purity from lower-grade domestic resources. As an important factor in preparedness, procurement of these high-grade, -critical ferroalloy minerals and metals for our nation&apos;s stock piles is a most important task. Also, this stock-piling can be the means of supplying incentive for the industrial development of the new metallurgical processes and plants necessary for the recovery of ferroalloy metals from our domestic low-grade deposits.

Jan 1, 1948

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By W. John Rankin

The finite and non-renewable nature of mineral resources poses unique challenges for sustainability: How can mineral and material needs of society be satisfied indefinitely? How can the benefits of exploitation of minerals best be captured for present and future generations? How can the environmental problems caused by large scale mining and processing best be ameliorated? These issues are rarely addressed, or if so only incidentally, in traditional courses in geology, mining, metallurgy and materials yet addressing them will increasingly be a major role for professionals in the minerals and materials industry and related sectors and agencies. This paper describes a framework for examining these and other sustainability issues related to meeting future material needs from non-renewable resources. The framework may be useful for educational purposes, either as the basis of a dedicated subject or by including the elements of it throughout a traditional course in relevant subjects.

Jan 1, 2014

By P. R. Dugan

The ultimate objectives and interest in removal of sulfur from high sulfur coal include: (a) reduction of the atmospheric load that con- tributes to the problem of acid precipitation; (b) reduction of ash which contributes to decreased energy transfer in boilers and the problem of ash disposal; and (c) alleviating the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. The cost of sulfur removal in relation to the value of refined coal will govern the development of an emerging coal-refining industry. The value of refined lower sulfur coal will be influenced by the national commitment to the environment as well as economic considerations.

Jan 1, 1986

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, &apos;longwall&apos; and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By V Pere

A geotechnical data management system has been developed to manage drillhole and mapping data generated from in house and consultant administered field programs. This system comprises a data collection interface with integrated validation, processing and reporting functionality. Development of the database required careful consideration of how and what geotechnical information is gathered in the field, a clear understanding of the interdependency of the parameters, and the outputs required to support geotechnical design.The acQuire Geoscientific Information Management System was selected as the preferred software to support the process because of its ability to easily manage data from capture in the field through to quality reviews and ultimately into reports. Initially only geotechnical logging of diamond core was considered, subsequently the system has been expanded to support additional geotechnical data sources such as laboratory test results, traverse and window mapping data. This paper focuses on the core logging data acquisition, validation, analysis and presentation of data.The acQuire Geoscientific Information Management System has proven to be a robust platform for the capture, interrogation, and reporting of geotechnical data. Data entry objects have been created to manage seven different areas of geotechnical data collection ranging from core logging to mapping to automated reports for falls of ground.

Aug 22, 2011

By J. J. Taute, S. J. Archer

"BASF Mining Solutions has developed a new-generation copper solvent extraction reagent that offers significant benefits over standard extractants currently available to the industry. As the name suggests, the new hightemperature (HT) extractant can be used at a higher operating temperature, but also exhibits significantly lower degradation rates, greater copper-toiron selectivity, and is totally nitration-proof compared with the standard extractants. Pilot-plant trials have also shown that lower aqueous-inorganic entrainment can be achieved. This paper investigates the technoeconomic benefit of using the HT extractant as an alternative to the standard extractant in a high-temperature application. The results of the technical evaluation showed that the use of the HT extractant reduces the extractant addition requirements and bleed volume from copper electrowinning; this smaller bleed requirement further reduces acid and limestone consumption, leading to a reduction in valuable metal losses. The results of the economic evaluation showed that the use of the HT extractant represents significant cost savings over that of the standard extractant. IntroductionCurrent solvent extraction (SX) reagents employed for the extraction of copper from typical pregnant leach solutions (PLS) at ambient conditions function well with minimal long-term effects on the extractant’s performance (Taute et al., 2015). This performance, however, deteriorates at elevated temperatures due to the degradation of the reagent’s hydroxyoximes. The degradation mechanism, acid-catalysed hydrolysis of the oxime, is accelerated by high temperature. This has a knock-on effect where the increase in degradation products increases the organic viscosity, leading to increased entrainment, crud formation, and ultimately to an increase in SX reagent consumption (Bender, Emmerich, and Nisbett, 2013).SX reagents also show an increase in the co-extraction of iron as the ferric concentration in the PLS increases. Co-extracted iron is transferred to electrowinning (EW) during stripping of the loaded organic and can adversely affect EW current efficiency. Iron in the EW circuit is typically managed by bleeding the electrolyte; however, this can lead to excessive consumption of EW reagents such as acid, cobalt, and mist-eliminating surfactants. The electrolyte bleed can also affect upstream consumption of reagents, such as lime, due to the high acid concentration recycled to leach."

Nov 1, 2018