Search Documents

By Rollie P. Dobyns

The K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6.5 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,018 barrels of 430 A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive. Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949. The K.M.A.? structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two "distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate-water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume of 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oil indicate that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 p.s.i., at which pressure 1 barrel of stock-tank oil contained 525 cubic feet of ea~ in solution.

Jan 1, 1952

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

By Carl E. Williams

During the past two years a computer program called "COPOR," Computerized Open Pit Optimization Routine, has been developed and used for mine planning of several base metal deposits. This routine utilizes a three dimensional computerized block model of an orebody, some economic parameters and operating constraints to locate the mineable or economic limits of the deposit schedule the yearly production from the mine and produce bench by bench ore reserve summaries and maps of the yearly and ultimate pit configurations. The moving cone method is used to perform these functions with a conventional block model. This model is conventional in the sense that each block is assumed to be homogenous; i.e., either ore or waste but not a mixture of the two. Due to the nature of a seam type deposit this approach is not realistic; therefore, revisions have been made to form a new version of the COPOR program. This version has been named "COALOR," Coal Optimization Routine. COALOR contains all of the power of the COPOR program but is equipped to handle the intricacies of coal seam type deposits. The deposit can be composed of a single seam or multiple seams which are horizontal or dipping at any angle. The numerous coal quality values can be incorporated to aid the optimization of the economic pit limits and yearly scheduling.

Jan 1, 1978

By A Manfrino

The Iron Bridge magnetite mine and infrastructure project is currently in development as a joint venture between Fortescue Metals Group, Formosa and Baosteel. It is supported by an extensive database of reverse circulation drill hole samples analysed by X-ray fluorescence (XRF), with a large subset tested for concentrate mass recovery, concentrate and tail grades by Davis tube recovery (DTR) testing. A limited number of rock physical testing results, including unconfined/uniaxial compressive strength and crushing work index, completes the database.By combining all available information – assays, DTR results, geology, stratigraphy, mineralogy and rock physical results – and using multivariate statistical analysis techniques, the impact of the critical factors that control concentrate quality, mass recovery and grindability characteristics have been outlined. A set of geochemical groups was created by using a cluster analysis technique from the combined XRF-DTR data. These groups allow optimal separation of material with consistently high concentrate Fe grades and mass recovery. This approach is superior to domaining based on stratigraphic logging or mass recovery as it is commonly used in standard magnetite estimation models. Using the results of a normative mineralogy study, the main geochemical groups were given a mineralogical profile fitting their geochemical characteristics. These findings further refined the understanding of the link between the process characteristics of the samples and their geochemical signature and mineralogy.The geochemical grouping defined on head grades and DTR concentrate mass recovery was generalised into a ‘geomet’ code based solely on the routinely assayed head grades, thus bypassing the need for systematic DTR testing. The geomet code identifies spatial domains with homogeneous geochemistry, mineralogy and process characteristics in both oxide and fresh material that form the basis of the current Iron Bridge resource model. The allocation of geometallurgical characteristics in terms of concentration amenability and concentrate characteristics on a block-by-block basis over the whole project allows for an optimum mine schedule and plant feed. This ensures that the desired concentrate characteristics and mass recovery can be better predicted over the life-of-mine, thereby improving the mine’s economics and stability by derisking the mine schedule and optimising the performance of the concentrators. A key benefit of the geomet code devised for the Iron Bridge mine is that it can be attributed in an automated manner to all samples analysed for a routine XRF analytical suite, from exploration to blasthole drilling. This allows each sample to be allocated to a geometallurgical material type with predictable process response in terms of concentrate mass recovery and concentrate quality without the need to complete systematic DTR testing.A standard multivariate analysis coupled with a cluster analysis has allowed the linking of interdisciplinary results between geology, mineralogy, geochemistry, process and metallurgy to better understand, predict and ultimately mine and process the Iron Bridge deposits. This allows plant operations and product quality to be optimised through each stage thanks to the predictable ore characteristics embedded in the mining model.CITATION:Manfrino, A, 2015. Unravelling the factors impacting on concentrate quality by geometallurgical data analysis at Fortescue Metals Group’s Iron Bridge magnetite mine, in Proceedings Iron Ore 2015, pp 567–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By Keith A. Heasley

The objective of this paper is to back-analyze the August 6th ,2007 collapse at the Crandall Canyon Mine in order to better understand the geometric and geo- mechanical factors which contributed to that collapse. In this work, the LaModel boundary-element program along with the best available information is used for the back- analysis. To initiate the analysis, a six step base model of the mining in he Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters: rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis , a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) Overall, the area was primed for a massive pillar collapse because of the large area of equal size pillars, 2) The abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse, 3) From the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2012

By Andrew T. Zador

The growing demand for energy combined with the need to protect and preserve the environment have become prime considerations in the design of efficient coal handling ports and their associated stockpiles. The transportation system is analogous to a connected chain which originates at the mines and terminates at steel mills or power plants, in which the port and the stockpile reserves are a vital link. Railroad transportation costs can be minimized by rapid discharge of the cars which, in turn, requires that an adequate stockpile system be available. Ocean transport costs can be minimized by having an efficient high capacity ship loading system and sufficient quantities of coal on hand -all of which also requires an efficient stockpile system to meet shipping demands. The connector between the two modes of transportation, therefore, is the port stockyard. It is here at the interface that optimization of land utilization and materials handling equipment results in a total transportation chain that can operate as a smooth efficient system. Multiple origins of coal require the simultaneous handling of large quantities of coal of many grades. Railroad transportation logistics often limit and define the incoming arrival patterns and limited rolling stock often require priority treatment for railroad operations. The physical limitations of prime ocean frontage require that coal stockpiles be built close to residential or industrial areas which entail strict environmental controls. Large capacity, enclosed coal stockpiles for ocean shipping have not yet been considered feasible but may be forthcoming in the near future. Several have been analyzed.

Jan 1, 1978

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By Gerald A. Crawford

"1880s - Unmasking the Sudbury Basin Falconbridge Ltd. turned 60 in 1988 but its roots go back more than a century to the discovery and development of the mineral resources of the Sudbury Basin. Nickel was first identified in the area in 1856 but sustained exploration awaited the early 1880s and the advance of the CPR westward from Sudbury. Rock was laid bare in the right-of-way and by forest fires and logging. Reddish oxidized outcropping or ""gossan"" were exposed, heralding the presence of nickel as the shape of this astounding geological formation gradually began to emerge. Many great mines of the area were opened up in this period on the south rim of the Basin west of Sudbury. To the east the ore dips below overburden, however, and Falconbridge remained a mere dot on the map until the turn of the century when Thomas Edison detected a magnetic occurrence by dip needle."

Jan 1, 1999

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By Donald R. Corson

The Bureau of Mines is conducting research on the effects of various established and potential soil-stabilization additives to hydraulic backfill. This initial phase is an evaluation of the effect of inclusion of varying amounts of Portland cement and combinations of cement and a dispersant on the bearing strength of backfill. Results of unconfined compression tests are given for over 200 sample cylinders incorporating a fill material with cement or cement and dispersant. Inclusion of a minor amount of dispersant (0.2 percent by weight) is found to yield a significant increase in strength for 20-to-1 and leaner sand-cement mixes. An apparent optimum concentration of dispersant exists beyond which no further increase in strength is achieved. A dispersant-cement ratio of l.8- to-1 yielded a strength increase of 515 percent over the strength of untreated 40-to-l sand-cement mixes.

Jan 1, 1966

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

By NILS DANIELSEN

THE name of Swedish charcoal iron will probably bring to the memory of many old consumers an extremely tough and ductile iron which was formerly used in considerable quantities for common blacksmith purposes. To-day very little of this iron goes to such kind of work. Swedish charcoal iron is merely a speciality which is chosen whenever its remark¬able properties can be utilized. By giving a rough sketch of the manufacturing process of Swedish charcoal iron, the character of the iron, its weak as well as its strong points will more easily be understood. Swedish charcoal iron is a wrought iron also known in the United States under the name of Norway iron and Swedish Lancashire iron. The name Norway iron seems to have been attached to the product for the reason that in the earlier days it was generally brought into the States by Norwegian ships. However no iron of this kind is now made in Norway. The reason for the name Swedish Lancashire iron is that the manufac¬turing process emanated from Lancashier in England, the method being generally adopted in Sweden in the years 1831-1850. Today this iron is, with the exception of one plant in the United States, made in no place in the world outside of Sweden.

Jan 1, 1924

By Juan L. Yarmuch, Hyam Rubinstein

Open-pit mine planning is a key process in the definition of mineral reserves and their efficient removal. Ore in open-pit mines is extracted bymining sequential pits called pushbacks. Pushbacks need to satisfy complex geometrical constraints to ensure the efficient usage of equipment. To date, no algorithms that both account for those constraints and maximizeNPV, are commercially available. Therefore, pushback design is done by engineers relying on their expertise to incorporate practical features intothe output of commercial tools. In this article, we present a new algorithm that produces close to optimal practical pushbacks and we illustrate its performance in real mines.

Jun 25, 2023

By Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Liang Yin, Xiaohui Fan

Straw char exhibited considerably faster burning speed than coke breeze for its porosity, which significantly degraded sinter quality when it replacing coke breeze as sintering fuel. In this investigation, preforming technology has been employed to densify raw straw. The properties of straw char preformed show that its density was increased, and the structure was also densified, which made the difference of combustibility between the straw char and coke breeze smaller. The proper preforming temperature, residence time and pressure were 200℃, 1min and 120MPa respectively. Sinter pot trials show that the product carbonized from preformed straw made the proper replacement ratio to coke breeze increase from 20% to 40%, and the emission reduction of SOx, NOx in flue gas increase from 11.50%, 14.15% to 37.85%, 23.60% respectively, compared with non-preformed straw char.

Jan 1, 2015

By Run-bo Wang, Zhe Wang, Fan-yi Meng, Jian-Liang Zhang

The influence of semicharcoal substitution for coke breeze on sintering performance was investigated by pot-grate sintering test. At a fixed fuel ratio, sinter productivity and strength decreased with the substitution increasing from 0 to 100% due to better combustibility. To enhance the utilization efficiency of 100% semicharcoal, sintering parameters (moisture and suction pressure) was adjusted. With the moisture increasing, sinter performance of 100% semicharcoal increased because of the suppression of semicharcoal incomplete combustion. As the moisture further increasing to 9.0%, sinter quality gave rise to a decrease trend. The results also showed that the increase of suction pressure was benefit for the increase of heat transfer rate, leading to the improvement of heat utilization energy. Measures to enhance magnetite oxidation during sintering are discussed based on current understanding of the fundamentals that control the sintering process.

Jan 1, 2015

By L Boczek

The term Engineer of Record (EoR) is commonly used in North America and South Africa to define the responsible person for the design, construction and operational phases of a tailings storage facility (TSF). Recently, this role has been elevated in prominence within Australia, but what does it really mean? Recent updates to international TSF guidelines suggests appointing an EoR is good practice, but where does the responsibilities of the EoR start and finish. Interestingly, both Samarco and Mount Polley failures had active EoR’s in place. This suggests that nominating an EoR alone, is not the full answer to mitigating the potential for a TSF failure. Appropriate construction and operational practices are key to the success of the design of TSFs, where all too often, operators ignore the operating plans developed by the designer. To be successful, a key consideration of the EoR role, is involvement in the operational phase of the TSF. This requires ‘buy-in’ from the mine managers and a change in the way TSFs are perceived by site. This paper explores how the roles and responsibilities of the EoR can assist in improving governance of TSFs if implemented effectively and what role the client has to ensure the success of the EoR.

Jul 1, 2021

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By John Paul Gries

This Bureau of Mines study outlines the history of 11 major metal ore deposits or districts that are relatively new discoveries. The oldest operation is the White Pine mine, where major exploration was initiated in 1929. Discovery (delineation of ore bodies) dates range from 1948 to 1976. All but two of the deposits, Quartz Hill in Alaska and Flambeau in Wisconsin, are or shortly will be in major production.

Jan 1, 1979

By R. A. Cattell

Every finding of the year's work, obtained under stress to meet present objectives, contributed to postwar needs, because the very nature and constitution of petroleum and natural gas require that research be conducted along the same general lines whether the results are applied in peace or war. More than 40 reports were submitted to the Petroleum Administration for War and others concerned with (1) evaluation of crude oils to determine their content of aviation-gasoline base stock, (2) evaluation of base stocks for blending with high-octane, synthetically manufactured components, (3) analyses of naphthas to determine their content of various types of hydro-carbons, such as benzene and toluene, and (4) the improvement of quality of marginal base stocks to meet future requirements of aviation gasoline. This upgrading of marginal stocks is being attained by selective distillation and chemical and catalytic removal of sulfur compounds. Asphalts were studied with respect to the characteristics of their various constituents in order to compound them, in the same way that aviation fuels now are being "built" to meet exacting requirements. The work previously initiated to give the industry fundamental data on thermodynamics of hydrocarbons progressed satisfactorily, and the heats of combustion of 10 hydrocarbons in the lubricating oil -range of petroleum were determined. Thermodynamic data requiring highly specialized techniques are so broad in application that their commercial usefulness is not yet fully appreciated.

Jan 1, 1946