Search Documents

By Antonio Adel dos Santos, Carmos Antonio Gandra, Fabricio Mazola da Silva Paiva, Vicente Tadeu Lopes Buono

Abstract Usiminas Steel Plant in Ipatinga installed an accelerated cooling device named CLC (Continuous On-Line Control) in 2010, enabling it to supply steels produced by TMCP (Thermo Mechanical Control Process) technology. This technology complements the TMCR (Thermo Mechanical Control Rolling), with the inclusion of the accelerated cooling process after controlled rolling. There are various gains in terms of quality and productivity associated to the application of such technology. However, the flatness control for API steel becomes crucial because large thermal stresses may be generated due to thermal heterogeneity during the fast cooling when the austenite phase decomposes mostly into ferrite and bainite. In literature, there is lack of knowledge regarding a full understanding of the relation among cooling conditions and plate flatness. Therefore, this work has focused on the effect of the cooling strategy for API steels, aiming at optimizing flatness and keeping the mechanical properties within the specified ranges. The starting point was dilatometer simulation, where cooling conditions such as start cooling temperature, SCT, finish rolling temperature, FRT, and cooling rate, CR, were changed in order to evaluate their effect on microstructure. Those laboratory conditions supposed to give the best results were transposed to industrial scale, so as to produce experimental lots of plates with five different cooling strategies. It was shown the possibility to find a cooling profile that guarantees the balance between mechanical properties and flatness requirements. The influence of cooling strategy on flatness was explained by the varied heat transfer regimes occurring from hot steel surface to the ambient

Oct 1, 2019

By Francisco Morganti

This report gives in the first part the metallurgical basics for the production of AHSS grades in integrated steel plants starting at the melt shop and ending at the annealing lines of the cold mill. The corresponding process and plant technologies in each production step with its specifics and rules are explained. In the second part by way of example the practical requirements for TRIP 780 steel grade are highlighted like a recipe for process control in the steel plant, hot and cold rolling mill, annealing line and finally skin pass mill. Measuring of mechanical technological properties on samples shows that the specifications according to DIN EN 10268 are fulfilled.

Oct 30, 2017

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Jorge Madias

O trabalho está baseado na análise de dados de perto de 200 fornos elétricos a arco de diferente design: convencional, de corrente contínua, de carcaças gémeas, com preaquecimento de sucata no transportador ou em shaft, etc. Incluem-se fornos que processam principalmente sucata, e fornos com carregamento parcial de gusa sólido ou líquido, ferro briquetado a quente (HBI) ou ferro esponja (DRI) a frio ou a quente. São avaliados os consumos de energia elétrica, oxigênio, gás natural e materiais carbonosos; os tempos entre vazamentos, com forno ligado e com forno desligado, assim como a produtividade horária. Com os dados obtidos, se analisa a influência dos metálicos (e seu estado térmico ao momento do carregamento), e o design do forno, sobre os consumos específicos mencionados e a produtividade.

Oct 30, 2017

By Adriane Lopes Mougo

Super duplex stainless steel presents a biphasic structure composed by ferrite and austenite with different characteristics and properties. In the micromilling process the cutting edge radius has similar dimensions to the grain size. The biphasic structure found in this material could influence on the cutting tool life and the surface integrity of the workpiece. Due to its low machinability, caused by high hardening level and low thermal conductivity, the process can produce built-up edge and high surface roughness (Ra). In this work it is performed an experimental study of the micromilling of super duplex UNS 32750 and the influence of the cutting speed (Vc) and feed per tooth (fz) on the surface integrity and tool wear. The design of experiments considered two levels and three replicates. Results indicate the increase of roughness for bigger feed per tooth, small influence of the cutting parameters on the burr formation. The tool presented flank wear after the experiments.

Aug 8, 2018

By Wilian da Silva Labiapari

Austenitic stainless steels are widely known for their good weldability, excellent mechanical properties for deep drawing and superior corrosion resistance in environments where most of the metals fail. Their uses include many applications subjected to a combination of mechanical and corrosive wear, such as pumps, valves and surgical implants. Although their corrosion resistance has been largely investigated, their resistance to mechanical wear is less studied. In particular, their performance under conditions involving combined corrosive and mechanical wear is not well understood. The aim of this study is to demonstrate the effect of the mechanical component on the electrochemical signal of an anodic polarization curve. A test rig was developed to investigate micro-abrasion-corrosion using a fixed ball configuration. Tests were carried out using stainless steel AISI 304 samples and 25.4 mm zirconia balls as counter bodies. The electrolyte was a 1N H2SO4 solution with SiO2 as abrasive dispersed at the concentration of 10 wt%. The results showed an increase in current density when the counter face roughness and the normal load applied during the tests are increased, evidencing a mechanical influence on the surface activity of this material in a corrosive environment.

Jul 31, 2018

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019

By Mariana Carla Mendes Rodrigues

The present study deals with the effects of strain rate on the functional behavior of NiTi thin wires. The samples, in the austenitic condition at room temperature, were mechanically cycled 20 times by loading up to 6% strain followed by complete unloading, at 25°C. Four different quasi-static strain rates were assessed: 1x10-4, 1x10-3, 1x10-2 and 5x10-2s-1. The functional properties are described by means of critical stress to induce martensite, stress at maximum strain, energy dissipated per cycle and residual strain. The sensitivity of repeated cyclic deformation to strain rate is also analyzed in terms of phase stability. The results show that the fluctuation in the loading plateau, due to non-homogeneous transformation, increases with increasing strain rate. During cycling, it is observed that higher strain rates result in lower critical stress to induce martensite after the 5th cycle. However, the stress at maximum strain is higher at high strain rates, regardless the number of cycles. The accumulation of residual strain also increases with the strain rate due to the higher applied stress. During unloading, both the elastic deformation of stress-induced martensite and the reverse transformation seem to overlap at high strain rates. The dissipated energy behavior changes between the 1st and 20th cycle. No martensite is stabilized after training, but the intensity of the X-ray diffraction peaks of austenite increases with strain rate, as a result of stress relaxation.

Aug 17, 2017

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Francisco Morganti

Weight reduction is the main target of all carmakers, which results in a continuous development of new steel grades. Latest 3rdgeneration advanced high-strength steel grades (AHSS) are complex materials with special chemical compositions and multiphase microstructures. The pickling, annealing and galvanizing processes of these grades aresomewhatdifferent due to the changed chemical compositions and microstructures. Therefore, these innovative steel grades place new demands on the plant technology of pickling, annealing and galvanizing lines. The most significant challenges for the pickling process are sludge occurrence during pickling, varying pickling times, weld ability of the materials, changed visual appearance and required high surface qualities. The most important topic concerning annealing line is a precisely controlled and very flexible heating and cooling process in the furnace.One of the new requirements in galvanizing linesis the prevention of surface faults caused by bare spots, which can occur since these materials feature a higher content of alloying elements like silicon or manganese. Prevention is possible with the special pre-oxidation technologies.Due to the higher strength of the material also the mechanical equipment has to be designed differently in these lines. This paper describes the influences of the changed chemical composition and material characteristics of modern steel grades on the pickling, annealing and galvanizing process and gives an overview about the technical solutions.

Oct 30, 2017

By Leandro de Almeida

Tiras e chapas de cobre e suas ligas possuem excelentes propriedades térmicas, elétricas e mecânicas simultaneamente e por isso podem ser utilizadas na fabricação de inúmeros produtos através de processos de conformação. Determinadas características devem ser analisadas na chapa antes mesmo do processo de manufatura, visando eliminar possíveis falhas durante as etapas de produção. Especificamente para o processo de repuxo profundo, faz-se necessário avaliar a possível formação de orelha e o possível afinamento da espessura da chapa durante a conformação. Sendo assim, o levantamento dos coeficientes de anisotropia planar ?r e o de anisotropia normal r são essenciais para se obter bons resultados nos processos de conformação. O presente estudo tem como objetivo avaliar a influência da deformação (e) na obtenção dos coeficientes ?r e r na liga UNS C22000, utilizada especificamente para a produção de projéteis A norma ASTM E 517 que apresenta a metodologia para se determinar esses coeficientes não especifica claramente qual e a ser utilizada. Os resultados alcançados não demonstram diferenças significativas com relação a e utilizada nos ensaios, ou seja, os coeficientes obtidos utilizando 0,10, 0,15 e 0,20 de deformação são os mesmos.

Aug 17, 2017

By Rodrigo Martins Barbosa

A água é utilizada em processos industriais desde o começo da era industrial. Sua utilização é variada, desde como matéria prima, até como utilidades. Muito se discute a respeito da qualidade da água para descarte e seus possíveis danos ambientais, mas é importante mostrar que, além disso, existe um impacto financeiro ao trabalharmos com a má qualidade da água industrial. Este trabalho propõe demonstrar a influência da qualidade da água nos processos industriais, através da avaliação do resultado da instalação de um filtro de água na tubulação de entrada de um trocador de calor.

Aug 17, 2017

By Fabiana Fonseca de Morais

A sinterização é um dos mais importantes e mais antigos processos de aglomeração da indústria metalúrgica. Entender a realidade atual do processo de sinterização e as qualidades requeridas para o sínter é primeiro passo para o desenvolvimento de equipamentos ou processo. Este trabalho visa entender o impacto das diferentes características de minério e resíduos empregados em uma sinterização, seu comportamento na qualidade do sínter e a sugestão de equipamentos para amenizar problemas encontrados. Parâmetros como CaO/SiO2, SiO2, Al2O3 e MgO são avaliados para entender a tendência do mercado e o efeito na qualidade final do sínter. A correta avaliação das necessidades da planta para otimização dos equipamentos a matéria-prima disponível se faz necessário para o melhor resultado no alto-forno. A granulometria da matéria-prima também é um ponto importante a ser analisado. O sinter feed tradicionalmente possui uma maior fração entre 0,7 e 6 mm, uma fração menor entre 0,2 e 0,7 mm e um conteúdo de ultrafino (<0,150 mm) limitado a 15%. Estudos identificam uma tendência do sinter feed com maior conteúdo de sílica e o consequente aumento da utilização de ultrafinos. Como resposta ao incremento de ultrafinos na sinterização as grandes siderúrgicas já estão investindo em equipamentos que minimizem grandes perdas de produtividade, como a instalação do misturador intensivo, utilizado em projetos da Pau Wurth. Outra solução inclui a instalação de uma mini-sinterização dedicada para receber este material mais fino e resíduos. O sínter produzido poderá ser adicionado diretamente no forno e/ou ser utilizado como nuclueante na sinterização grande para aumento de sua produtividade.

Aug 16, 2017

By Fabio Da Costa Garcia Filho

O uso de resíduos de vidro como aditivo mineral finamente moído, em substituição parcial de cimento e agregados é uma direção promissora para a reciclagem. Este trabalho teve como objetivo analisar a influência de resíduos do processo de corte de vidro em argamassa adesiva, como substituição parcial de cimento e agregado miúdo. O vidro em pó foi utilizado em percentuais de 10, 15 e 20% em peso em substituição ao cimento Portland e, em outro momento, em substituição ao miúdo agregado. Verificou-se que a substituição refletiu positivamente sobre a resistência à adesão da argamassa, com o aumento da temperatura de cura.

Oct 30, 2017

By Dyego Irineu Silva de Almeida

O presente trabalho teve como objetivo analisar os efeitos dos ciclos de tratamento térmico de recozimento, normalização e esferoidização nas características microestruturais do aço SAE 8620. O aço SAE 8620 é amplamente utilizado na fabricação de engrenagens, pinos e peças onde há exigência de dureza superficial, obtida pelo processo de cementação ou carbonitretação. O aço SAE 8620 é empregado na construção de mecanismos onde a resistência ao desgaste é propriedade mais importante. Para essa aplicação, aços com baixo teor de carbono produzem um núcleo tenaz e os tratamentos termoquímicos conferem as características superficiais necessárias. O espécime original foi caracterizado através dos procedimentos necessários para visualização da microestrutura, bem como as amostras provenientes dos tratamentos térmicos. Sabe-se que o estudo metalográfico de um material é de grande importância para a identificação de suas propriedades, haja vista que essas propriedades estão diretamente relacionadas com a microestrutura que o material possui. Concluiremos que os diferentes ciclos de tratamento térmico, influenciam diretamente nas microestruturas das peças tratadas termicamente, como também na propriedades mecânicas.

Oct 30, 2017

By Ângelo Siqueira da Silva

Este trabalho teve por objetivo avaliar o potencial gratifizante de adições de alumínio, em conjunto com inoculante a base de silício, diretamente no fundo do basquete antes do basculamento da panela de metal líquido no basquete da máquina centrífuga, a fim de produzir tubos centrifugados de ferro fundido nodular de matriz majoritariamente ferrítica. Amostras extraídas da ponta e cabeça dos tubos, sem e com distintas adições de alumínio, foram submetidas a tratamentos de recozimento (1050, 1000 e 900ºC), a fim de serem analisadas por meio de análise microestrutural e dureza Brinell. De acordo com os resultados obtidos a incorporação de alumínio ao ferro fundido foi mais efetiva para a incorporação de 1,7% de Al no ferro fundido, permitindo obter um ferro fundido nodular de composição ligeiramente hipereutética, com adequada grafitização e matriz 100% ferrítica, mesmo nas condições testadas com menor temperatura de encharque (900ºC) no recozimento, e com dureza dentro das especificações para a aplicação.

Aug 16, 2017

By Anna Paula Littig Berger

O objetivo do presente trabalho foi estudar a influência da adição de argônio à atmosfera de redução a plasma sobre a redução de pós de hematita. Os experimentos de redução foram realizados em reator a plasma pulsado DC, sob pressão de 533 Pa, temperatura de 380ºC, tempo de 60 min, fluxo total de hidrogênio e de argônio de 400 cm3/min e variando os teores de argônio e hidrogênio. Os resultados mostram que os aglomerados de partículas após redução possuem um aspecto esponjoso. Verificou-se que o uso de uma mistura gasosa contendo 2% de Ar e 98% de H2 permite um aumento de aproximadamente 7,76% na fração de redução.

Aug 8, 2018

By Luiz Gabriel da Silva Nascimento

Foi fabricada uma matriz hipoeutética de Al-2%Ni e adicionado nela concentrações de 0,5; 1,0; e 1,5 % de nanotubos de carbono de paredes múltiplas (NTCPM). A fabricação do material estudado aconteceu por fundição e resfriamento unidirecional brusco originado grãos predominantemente colunares. Os ensaios mecânicos mostram que concentrações maiores de nanotubo na matriz provocam acréscimo na propriedade mecânica e que em áreas mais distante da base extratora de calor a microdureza aumenta. Na amostra que contém 1,5% de nanotubos o valor da microdureza em áreas da posição P1 distante 5 mm da interface metal/molde é aproximadamente de 120 HV, já em áreas da posição P5 distante 45 mm, se aproxima de 210 HV. A resistência a tração é influenciada pela adição de NTC. A matriz possui uma resistência a tração de 64 Mpa, enquanto que a adição de 1,5% de NTC eleva esse valor para 135 MPa.

Aug 17, 2017